Square Flame Patio Heater Instruction Manual
Contents
1. T 19 7 S00mm IIIA AIA AUT TOU LEO LOUIE LEER a MAINTENANCE CLEANING AND MAINTENANCE WARNING FOR YOUR SAFETY DO NOT touch or move heater for at least 45 minutes after use Allow all burner elements to cool before touching To enjoy years of outstanding performance from your heater make sure you perform the following maintenance on a regular basis Keep exterior surfaces clean 1 Use warm soapy water for cleaning Never use flammable or corrosive cleaning agents 2 While washing your heater be sure to keep the area around the burner and pilot assembly dry at all times If the gas control is exposed to water in any way DO NOT try to use it It must be replaced Keep the heater area free and clean from combustible materials gasoline or other flammable vapors and liquids Visually check burner flames Incorrect lame w i p ty 1 Cormect Name Visually check the hose assembly inside the post and check for any cracks or worn sections 1 Unscrew gas hose and regulator hose with 3 4 inch open end wrench and adjustable wrench 2 Check if there are any cracks or worn sections on hose If yes contact your gas supplier to replace the hose 3 At least once a year the unit should be inspected for the presence of spiders spider webs or other insects Air flow must be unobstructed Keep controls burner and circulating air passageways clean Signs of possible blockage include 1 Gas2. installation included operating and maintenance instructions thoroughly NOT included before installing or servicing this equipment eAdjustable opening wrench 8 long ePhilips screwdriver w medium blade WARNING eSpray bottle of soapy solution For Outdoor Use Only for leak testing LPG Cylinders to be used must be constructed and marked in accordance with US DOT specifications Storage of the heater indoors is permissible only if the gas cylinder is turned off and removed NOTE Use only 20Ib LP Gas tank with size of 18 1in 46cm Height 12 5in 32cm Width Do not use if the environment temperature is below 40 degrees F 4 4 degrees C PRECAUTIONS NOTE PLEASE READ THE FOLLOWING SAFETY RULES WARNING This heater must only be used outdoors Using this product in an enclosed area may cause injury death or property damage Only use in a well ventilated space Do not use in a building garage or any other enclosed area Read the instructions before use This heater must be installed in accordance with local codes or in the absences of local codes with the National Fuel Code ANSI Z223 1 If applicable the heater when installed must be electrically grounded in accordance with local codes or in the absence of local codes with The National Electrical Code ANSI NFPA70O Do not use the heater in an explosive atmosphere Keep the heater away from areas where gasoline or other flammable liquids or vapors are stor
3. odor with extreme yellow tipping of flame 2 Heater does not reach the desired temperature 3 Heater glow is excessively uneven 4 Heater makes uneven popping noise Spiders and insects can nest in burner or orifices This dangerous condition can damage heater and render it unsafe for use Clean burner holes by using a heavy duty pipe cleaner Compressed air may help clear away smaller particles Carbon deposits may create a fire hazard Clean dome and engine with warm soapy water if any carbon deposits develop NOTE In a salt air environment such as near an ocean corrosion occurs more quickly than normal If the heater is exposed to this type of environment you should frequently check for corroded areas and repair them promptly TROUBLESHOOTING Pilot will not light Turn the gas valve ON OFF Plot will nat stay on Burner will not light Pilot light assembly Place pilot in proper bent or not in correct Position and retry location Burner flame goes Low gas pressure Let the pilot flame stay lit off immediately for 10 minutes before after ignition setting variable knob to LO 20 Distributed By Well Traveled Living 716 S 8 Street Amelia Island FL 32034 Toll Free 866 WTL SUPP Web www wtliving com Email cservice welltraveled net 1 YEAR LIMITED WARRANTY Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner again
4. Patio Heater Model PHO8 SA PHO8 SSA Item 60804 WARNING For outdoor use only FOR YOUR SAFETY If you smell gas 1 Shut off gas to the appliance F AAR EARREABLORRAT RLABEAM RII A F eee esses seesier dissin f in TEET iitidttiiti TAA TELET zi eens 2 Extinguish any open flame EER 3 If odor continues immediately call Zik gas supplier ed bee TA PEE pra eae AANA t FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance CCP Cee er VAR ee ee ETIE Conforms to ANSI STD Z83 26a 2008 pa Certified to CSA STD 2 37a 2008 C US Listed Intertek 3177588 Instruction Manual amp Parts List INSTALLER Please leave this manual for the consumer CONSUMER Please retain this manual for future reference MANUFACTURER Changzhou Wellife Furnace Co Ltd l Tools and parts needed for assembly CARBON MONOXI DE HAZARD This appliance can produce carbon monoxide which has no odor Using itin an enclosed space can kill you Never use this appliance in an enclosed space such as a camper tent car or home WARNING Improper installation adjustment Tools needed alteration service or maintenance can cause injury eOpen end wrench 10 amp 13mm or property damage Read the
5. S IN THE ASSEMBLY AND OPERATION OF THIS UNIT FAILURE TO FOLLOW WARNINGS AND OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN SEVERE PROPERTY DAMAGE AND OR PERSONAL INJURY IN NO EVENT WILL WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CONTRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDIRECT SPECIAL PUNITIVE EXEMPLARY CONSEQUENTIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE MAINTENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL WELL TRAVELED LIVING OR ITS OFFICERS DIRECTORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER This limited warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sales of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty 1IMIPORTANT NOTICE Do NOT return to place of
6. ed Prior to use check for damaged parts such as hoses regulators pilot or burner Turn off and disconnect LPG cylinder before moving the heater Do not attempt to alter this heater in any manner EXAMPLE Using the heater without the top canopy reflector or radiant screen Do not use this heater in basements or below ground level It must always be placed on a solid and level surface Always ensure there is ample fresh air ventilation For outdoor use ONLY Never replace or substitute the regulator with any regulator other than the factory suggested replacement Do not clean the heater with cleaners that are combustible or corrosive Do not paint radiant screen control panel or top canopy reflector All leak tests should be done with a soapy solution NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS The LPG cylinder should be turned off when the heater is not in use At least once a year the unit should be inspected for the presence of spiders spider webs or other insects PRECAUTIONS CHECK THE HEATER IMMEDIATELY IF ANY OF THE FOLLOWING EXIST 1 The smell of gas in conjunction with extreme yellow colored tips of the burner flames 2 The heater does not reach temperature 3 The burner makes a popping noise during use a slight popping noise is normal when the burner is extinguished after using Children and adults should be aware of the hazards of high surface temperature and should stay away to avoid burns or clothing
7. el is clear of debris Be sure any component removed during assembly or servicing is replaced and fastened prior to starting Before Lighting Heater should be thoroughly inspected before each use Have a qualified service person inspect the heater at least annually If relighting a hot heater always wait at least 5 minutes OPERATION LIGHTING INSTRUCTIONS a TO TURN ON THE HEATER n Fa 1 Turn the control knob OFF i 2 Slowly open the gas cylinder valve YWL 3 Press and turn the control knob to w E ie FF position and hold for 30 seconds While holding down the control knob press the igniter several times until the pilot flame ignites Release the knob after ignition Note If the pilot flame does not light or it goes out repeat Step 3 To regulate the heat turn the control knob to LO position or HI position 4 If the burner flame goes out accidentally or it is blown by wind turn off the heater and wait at least 5 minutes or more to let the gas dissipate before relighting to avoid gas explosion Repeat steps 2 to 4 WARNING FOR YOUR SAFETY NOTE If at any time you are unable to light burner and smell gas wait 5 minutes to allow gas to dissipate before attempting to light heater If after 1 minute you are unable to light burner wait 5 minutes and allow flammable vapors to dissipate before attempting to light heater again If a new tank has just been connected please allow a
8. hed to the base assembly and then lower the second piece of glass tube over the glass tube connector Lay Step 8 Attach the other glass tube fixed part 4 to the upper plate 11 with 3 pcs M4x8mm screws 21 ASSEMBLY Step 9 Put the assembled upper plate from Step 8 on top of the assembled support connectors and use 4pcs M12 screws 15 to secure it Step 10 Attach 4pcs mesh guard 10 on the lower support connectors NOTE The long side will connect with the base assembly 10 Pee if Pa Pr a tat ey at HH lit ASSEMBLY Step 11 Attach 4pcs mesh guard 10 on the upper support connectors eee eerie Sera ih hd a a a a i at AF ut i it A th i i fet iF i Peta ed ae Step 12 Attach 4pcs mesh fixed parts 13 on the assembled upper plate with l 4pcs M4x8mm screws 22 ta id o e gi mi na 1 J M L S z j i 1 rd i he z lj ti p F ii _ot 7 E A 1 ASSEMBLY Step 13 Attach the top reflector 12 on the assembled upper plate with 3pcs 3 16 screws 19 and 4pcs M5x10mm bolts 16 Step 14 Open the front panel of base assembly 1 Attach 3pcs gas cylinder fixed parts 14 on the base with 6pcs M6x12mm bolts 18 12 ASSEMBLY Step 15 Connect the regulator Preassembled with the burner to the LPG cylinder and hand tighten then put gas cyl
9. icable for connection NO 510 in the standard for compressed gas cylinder valve outlet and inlet connections ANSI CGA v 1 2 The cylinder supply system must be arranged for vapor withdrawal 3 The cylinder used must include a collar to protect the cylinder valve Annually check operation A Open the front panel of the base assembly B Open the propane tank valve C Spoon several drops or use squirt bottle of the solution onto gas hose connection and pilot connection Inspect the connections and look for bubbles If no bubbles appear the connection is safe If bubbles appear there is a leak Close the propane tank valve and loosen and re tighten this connection G Check for leaks again H If bubbles still appear close the propane tank and refer to instructions under 8 on page 14 DO NOT attempt to use the heater mm 15 OPERATION WARNING DO NOT attempt to operate the heater until you have read and understand all precautions Failure to do so can result in serious personal injury death or property damage Before Turning Gas Supply ON Your heater was designed and approved for OUTDOOR USE ONLY _DO NOT use it inside a building or any other enclosed area Make sure surrounding areas are free of combustible materials such as gasoline and other flammable vapors or liquids Ensure that there is no obstruction to air ventilation Be sure all gas connections are tight and there are no leaks Be sure the access pan
10. ignition Young children should be carefully supervised when they are in the area of the heater Clothing or other flammable material should not be hung from the heater or placed on or near the heater Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater Installation and repair should be done by a qualified service person The heater should be inspected before use and cleaning may be required at least once a year or as necessary It is imperative that the control compartment burner and circulating passageways of the heater are kept clean Keep the heater area clear of combustible materials such as gasoline and other flammable vapors and liquids Do not obstruct the flow of combustion and ventilation air Keep the ventilation opening of the LPG cylinder enclosure free and clear of debris Storage of a heater indoors is permissible only if the LPG cylinder is turned off disconnected and removed from the heater Cylinders must be stored outdoors in a well ventilated area out of the reach of children Disconnected cylinders must have threaded valve plugs tightly installed and must not be stored in a building garage or any other enclosed area o ASSEMBLY L PE Base assembly with tank and control housing 2pcs wheels Handle 2pcs glass tube fixed parts one for top one for bottom 2pcs glass tube Glass tube connector 4pcs lower support 4pcs upper s
11. inder on the base i ii Warning When connecting the gas cylinder and regulator make sure the connection is tight and always check for leaks Please see page 14 Check for Leak for full instructions 13 ASSEMBLY Check for Leak Your patio heater has been checked at all factory connections for leaks but you should always check when you attach the LPG cylinder To check for leaks follow these instructions Assemble all gas connections Connect regulator assembly to the propane tank Make sure the heater valve is turned OFF 1 Make soapy solution by mixing 1 part liquid dish soap and 3 parts water 2 Open the propane tank valve 3 Spoon several drops or use squirt bottle of the soapy solution onto the gas hose regulator and regulator cylinder connection 4 Inspect the connections and look for bubbles 5 If no bubbles appear the connection is safe 6 If bubbles appear there is leakage Close the propane tank valve and loosen and re tighten this connection 7 Check for leakage again 8 If bubbles still appear and the leak is with the regulator or hose close the propane tank valve and contact customer support If a leak is detected DO NOT attempt to use the heater MAKE SURE to check all THREE connections between the cylinder and gas line 14 ASSEMBLY NOTE 1 The cylinder must be provided with a shut off valve terminating in a LPG supply cylinder valve outlet specified as appl
12. purchase For customer service and warranty issues contact our Customer Service Center at 866 985 7877 OR Email cservice welltraveled net Customer Service Hours Mon Fri 9 00 a m 6 00 p m EST Fire Sense Mojave Sun and Well Traveled Living are registered trademarks of Well Traveled Imports Inc All assembly instruction presentations are the property of Well Traveled Imports Inc and are protected by U S copyrights and trademarks All rights reserved
13. st defects in materials and workmanship under normal use This warranty does NOT cover normal wear and weathering assembly and or maintenance OR use in a commercial application At Well Traveled Living s sole discretion products under warranty will be repaired and or replaced at no charge to the customer Any returns sent back to Well Traveled Living must be sent via prepaid freight and in the original retail packaging For warranty service contact Well Traveled Living at the address phone numbers or internet site and email listed in this owner s manual Be sure to have your sales receipt date of purchase and catalogue model numbers available when calling All warranty service will be coordinated by the Well Traveled Living s Amelia Island Florida service center This warranty is extended only to the original purchaser Proof of purchase will be required before warranty service is rendered The sales receipt is the only valid proof of purchase This warranty only covers failures due to defects in materials or workmanship which occur during normal use Failures and or damage which result from accident negligence misuse abuse neglect mishandling alteration or modification failure to maintain improper assembly or maintenance service by unauthorized agency or use of unauthorized components or damage that is attributable to acts of God are NOT covered THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED ABOVE PURCHASER ASSUMES ALL RISK
14. t least one minute or more for the air in the gas pipeline to purge out through the pilot hole When lighting the pilot flame make sure that the control knob is continuously depressed while pressing the igniter button Variable control knob can be released after the pilot flame has been lit for 20 30 seconds Pilot flame can be watched and checked from the peephole located on the base of burner TO TURN OFF THE HEATER 1 Press and turn the control knob to a Md ad g i ies iit OFF position a a Y ee A 2 Turn off the valve on the gas cylinder Cy iy E WW j be disconnect the cylinder Soi NITER a al LO WARNING N Heater will be hot after use Handle with extreme care 17 LOCATION OF HEATER WHILE IN USE CAUTION WHEN CERTAIN MATERIALS OR ITEMS ARE LEFT UNDER THIS HEATER WHILE IN USE THEY WILL BE SUBJECT TO RADI ANT HEAT AND COULD BE SERI OUSLY DAMAGED This heater is to be used for the heating of outdoor patios decks spas pool and open working areas This heater is for outdoor use ONLY Always make sure that adequate fresh air ventilation is provided and follow the spacing tolerances shown in the picture below The minimum clearances must be maintained at all times This heater must be placed on level firm ground Never operate in an explosive atmosphere Keep away from areas where gasoline or other flammable liquids or vapors are stored or used ULN HD
15. upport 4pcs support connector 8pcs mesh guard Upper plate Top reflector 4pcs mesh fixed parts see exploded view below 3pcs gas cylinder fixed parts and 3pcs M8x25mm bolts to secure LPG cylinder on base 4pcs M12 screws 4pcs M5x10mm bolts 4pcs M6x12mm bolts 6pcs M6x12mm bolts 3pcs 3 16 screws 3pcs M4x8mm screws 3pcs M4x8mm screws 4pcs M4x8mm screws 8pcs M6x18mm bolts 24 8pcs M6 nuts ASSEMBLY WARNING This appliance requires installation by a competent person Proper assembly is the responsibility of the installer Step 1 Attach the wheels 2 to the base assembly 1 with 8pcs M6x18mm bolts 23 and 8pcs M6 nuts 24 Step 2 Attach the handle 3 to the back panel of the base assembly 1 with 4pcs M6x12mm bolts 17 p ASSEMBLY Step 3 20 Attach one of the glass tube fixed parts 4 on the base assembly 1 with 3pcs M4x8mm screws 20 Step 4 Screw the 4pcs lower support 7 into the holes located on the top of the base assembly 1 ASSEMBLY Step 5 Put the 4pcs of the support connector 9 onto the tops m of the 4 lower supports 7 Step 6 Screw the 4 upper supports 8 onto the 4 lower supports 7 ASSEMBLY Step 7 Fit one piece of the glass tube 5 into the glass tube fixed part 4 on top of the base assembly 1 Insert the glass tube connector 6 into the glass tube piece already attac
Download Pdf Manuals
Related Search