Dell PowerVault MD3400 and MD3420 Series Storage Arrays
Contents
1. For more information see the Dell PowerVault MD34xx 38xx Series Support Matrix at dell com support manuals a Install the software and driver package included on the PowerVault MD series resource media For information about installing the software see Installing PowerVault MD Storage Software b Set up the PowerVault MD1200 series expansion enclosure s For information about setting up the PowerVault MD1200 series expansion enclosure s see the Owner s Manual at dell com support manuals c Using MDSM update the RAID controller module firmware and NVSRAM to the latest versions available on dell com support manuals d Click Tools Upgrade RAID Controller Module Firmware from the Enterprise Management Window EMW 2 Stop I O and turn off all systems a Stop all I O to the storage array and turn off affected host systems attached to the storage array b Turn off the storage array c Turn off any expansion enclosure s in the affected system 3 Cable the expansion enclosure s to the storage array a Connect the MiniSAS HD end of the supported SAS cabled to the SAS OUT Port O on the MD 1200 series array b Connect the other end of the SAS cable to the IN port on the MD 1200 series array 4 Turn on attached units a Turn on the expansion enclosure s Wait for the enclosure status LED to light blue b Turn on the storage array and wait for the status LED to indicate that the unit is ready Ifthe status LEDs are2. Number 1 12 gbps SAS Host Ports 2 Allows you to connect host servers to the storage array 2 7 segment display Displays status of the controller 3 1G Ethernet Management MGMT Port 1 Allows for out of band management of storage array 4 Reserved Ethernet Port 1 This is a reserved port 12 gbps SAS Host Ports 2 Allows you to connect host servers to the storage array 6 SAS Expansion Ports 2 Allows you to connect the storage array to optional PowerVault MD1200 series expansion enclosures for additional storage capacity NOTE Only one SAS OUT expansion port can be used at a time and the recommended expansion port is port 0 K NOTE Do not cable the reserved management port Each PowerVault MD3400 and MD3420 storage array can be expanded to a maximum of 120 slots or 192 if enabled using Premium Feature activation through a maximum of seven MD1200 series expansion enclosures Cabling The Storage Array You can cable the storage array to host servers with e Single path data configuration A single path configuration allows you to connect a maximum of eight hosts This is a non redundant configuration e Dual path data configuration A dual path configuration allows you to connect a maximum of four hosts Choose the data configuration based on Number of hosts required e Level of data redundancy required Redundant And Nonredundant Configurations Nonredundant configurations are configurations that
3. With mixed host support the data paths might have different bandwidths or different data transfer speeds Least Queue Depth The least queue depth policy is also known as the least I Os or least requests policy This policy routes the next I O request to a data path that has the least outstanding I O requests queued For this policy an I O request is simply a command in the queue The type of command or the number of blocks that are associated with the command are not considered The least queue depth policy treats large block requests and small block requests equally The data path selected is one of the paths in the path group of the RAID controller module that owns the virtual disk Least Path Weight The least path weight policy assigns a weight factor to each data path to a virtual disk An I O request is routed to the path with the lowest weight value to the RAID controller module that owns the virtual disk If more than one data path to the virtual disk has the same weight value the round robin with subset path 29 selection policy is used to route I O requests between the paths with the same weight value The least path weight load balance policy is not supported on Linux operating systems Changing Load Balance Policies On The Windows Server Operating System Load balancing with the PowerVault MD series storage array can be done from the default round robin with subset by using either the e Device manager e Disk management
4. manuals The PowerVault MD series resource media provides features that include the core software providers and optional utilities The core software feature includes the host based storage agent multipath driver and Modular Disk Storage Manager MDSM application used to configure manage and monitor the storage array solution The providers feature includes providers for the Microsoft Virtual Disk Service VDS and Microsoft Volume Shadow Copy Service VSS framework NOTE For more information about the Microsoft VDS and Microsoft VSS providers see the Owner s Manual To install the software on a Windows or Linux system you must have administrative or root privileges K NOTE If Dynamic Host Configuration Protocol DHCP is not used initial configuration of the management station must be performed on the same physical subnet as the storage array Additionally during initial configuration at least one network adapter must be configured on the same IP subnet as the storage array s default management port Controller O MGMT port 1 192 168 129 101 or Controller 1 MGMT port 1 192 168 129 102 After initial configuration the management ports are configured using MDSM and the management station s IP address can be changed back to the previous settings K NOTE Only two management ports per array are supported Second port on each controller is reserved The PowerVault MD series resource media offers the following three installat
5. Changing Load Balance Policies Using Windows Server Device Manager Follow the steps to change the load balance policy using Windows Server device manager 1 Right click My Computer and select Manage to open the Computer Management dialog box 2 Click Device Manager to show the list of devices attached to the host 3 Right click the multipath disk device for which you want to set the load balance policies then select Properties 4 From the MPIO tab select the load balance policy that you want to set for this disk device Changing Load Balance Policies Using Windows Server Disk Management Follow the steps to change the load balance policy using disk management Right click My Computer and click Manage to open the Computer Management dialog box Click Disk Management to show the list of virtual disks attached to the host Right click the virtual disk for which you want to set the load balance policy then click Properties gt NN ES From the MPIO tab select the load balance policy that you want to set for this virtual disk 30
6. path to a virtual disk through a specific RAID controller module When the multi path driver receives a new I O to process the driver tries to find a path to the current RAID controller module that owns the virtual disk If the path to the current RAID controller module that owns the virtual disk cannot be found the multi path driver migrates the virtual disk ownership to the secondary RAID controller module When multiple paths to the RAID controller module that owns the virtual disk exist you can choose a load balance policy to determine which path is used to process I O Multiple options for setting the load balance policies let you optimize I O performance when mixed host interfaces are configured NOTE For more information on Load Balance Policy see your operating system s manual and updates You can choose one of the following load balance policies to optimize I O performance e Round robin e Least queue depth e Least path weight Microsoft Windows operating systems only Round Robin With Subset The round robin with subset I O load balance policy routes I O requests in rotation to each available data path to the RAID controller module that owns the virtual disks This policy treats all paths to the RAID controller module that owns the virtual disk equally for I O activity Paths to the secondary RAID controller module are ignored until ownership changes The basic assumption for the round robin policy is that the data paths are equal
7. provide only a single data path from a host to the storage array This type of configuration is only recommended for noncritical data storage Path failure from a failed or removed cable or a failed or removed RAID controller module results in loss of host access to storage on the storage array Redundancy is established by installing separate data paths between the host and the storage array Each data path is connected to one of the two RAID controller modules installed in the storage array Redundancy protects the host from losing access to data in the event of path failure because both RAID controller modules can access all the disks in the storage array 10 Single Controller Configurations The following figures show two and four hosts each connected to only one RAID controller module The hosts can share storage space but without redundant paths if one path fails the server on that path would be disconnected from the storage array Server 1 Storage Array Eo L Management Network Figure 2 One Host Connected to a Single Controller 11 Server 1 Server 2 Storage Array Management Network Figure 3 Two Hosts Connected to a Single Controller Using Two HBAs 12 Server 1 Server 2 Storage Array Management Network Figure 4 Two Hosts Connected to a Single Controller Using One HBA 13 Server 1 Server 2 Server 3 Server 4 EE 01 01 de m a giles HBA HBA HBA HBA HBA HBA HBA HBA St
8. solid amber the storage array is still coming online If the status LEDs are blinking amber there is an error that can be viewed using MDSM Ifthe status LEDs are solid blue the storage array is ready c After the storage array is online and ready turn on any attached host systems 5 Using MDSM update all attached expansion enclosure firmware if it is out of date a From the EMW select the enclosure that you want to update and enter the Array Management Window AMW b Click Advanced Maintenance gt Download EMM Firmware c Select Select All to update all the attached expansion enclosures simultaneously 22 Installing PowerVault MD Storage Software The Dell PowerVault MD series resource media contains software and drivers for both Linux and Microsoft Windows operating systems The root of the media contains a readme txt file covering changes to the software updates fixes patches and other important data applicable to both Linux and Windows operating systems The readme txt file also specifies requirements for accessing documentation information regarding versions of the software on the media and system requirements for running the software For more information on supported hardware and software for Dell PowerVault systems see the Dell PowerVault MD34xx 38xx Series Support Matrix at dell com support manuals NOTE It is recommended that you install all the latest updates available at dell com support
9. D Storage Software From WIiNdOWG cccccccceeeeceeeeeeeeeeeeeeeeeeeseaeeeeeesceeeesseeeeeesseees 27 Uninstalling MD Storage Software From Windows Server GUI VersiOns cccceeeeeeeeeeeees 27 Uninstalling MD Storage Software From Windows Server Core VersiOns cceeseeeeeeeeeees 27 Uninstalling MD Storage Software From LiNUX oococcioocccconooccccononnncnnonnnnnonnnnncnnnnnnnnnnnennnnnnnnnnnncnnnnnccnnns 27 2 Load Balan cid ni aa 29 Load Balance Poli da 29 Round RObIA With SUBSEt ua la ia eel ence 29 Least Que Dep A Eee errr e a Sunnie dees deeutinnsh autacrancdanttinciveuss dtecTaedlaivecsdences 29 Le astsRathy WIG a read aia Changing Load Balance Policies On The Windows Server Operating System Introduction This document provides information about deploying Dell PowerVault MD3400 and Dell PowerVault MD3420 storage arrays The deployment process includes e Hardware installation e Modular Disk Storage Manager MDSM software installation e Initial system configuration Other information includes system requirements storage array organization and utilities K NOTE For more information on product documentation see Related Documentation MDSM enables an administrator to configure and monitor storage arrays for optimum usability The version of MDSM included on the PowerVault MD series resource media can be used to manage both the Dell PowerVault MD3400 and Dell PowerVault MD3420 systems and the e
10. DE 9 Cabling The Storage Array ios a AE RA a a A 10 Redundant And Nonredundant Configurations ecececcecscceeentecseeeeeneeeeneeeseeesnereseeessiresenteeeas 10 Single Controller CONFIQUIATIONS ccccccccsceescessecsecssccseecseesseecsessseesseessessueessecseecseecsessstenseesstenies 11 Dual Controller Configuration S mermsrsamara not ladies 14 Cabling PowerVault MD1200 Series Expansion EnclosureS oocccoccnnocicoonncconccnnn conan ncnnnncnnnnncnnnncnnn nono 20 Expanding With Previously Configured PowerVault MD1200 Series Expansion Enclosures 21 Expanding With New PowerVault MD1200 Series Expansion EnclosureS oocciccocccccnocccccconcccc no 22 3 Installing PowerVault MD Storage SoftWare oooocoooccoccocciccccccoccoonoonconccnnonnons 23 Graphical Installation RecomMmMended ooooocoococococinococccccnoonncononnncnnnnonnnnonnnnnncnnnnnnnnnnnnnnnnanennnnnnnnnnnnnanns 24 a ieee e eaae weal ee Mise ek be eo ob La een dh an a m ae Made leads Ra eee 24 Sil rtInsta lation ce daa ERA e ASE e idos 25 Silent Installation On Windows SySteMs ccc ccccecsceeeeeececeeceseeeeceseeeeeeseaeeeeseneeeeeseaaeeesscneeeeeeaes 25 Silent Installation On Linux SysSteIMS ooooooccccconoccccnononcnnnnnncnnncnnnccnnnnnnnnnnnnnn cnn naar nnnnnannnn nn nnnnnnnnannnnn 25 Upgrading MD Storage Softwa esse srira e ar aai Gad EA dea 25 4 Uninstalling MD Storage SoftWare ooocococccocninncccnoccconconccnnocononoononnnonnonnonnons 27 Uninstalling M
11. Dell PowerVault MD3400 and MD3420 Series Storage Arrays Deployment Guide Notes Cautions and Warnings Es NOTE A NOTE indicates important information that helps you make better use of your computer A CAUTION A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem A WARNING A WARNING indicates a potential for property damage personal injury or death Copyright O 2014 Dell Inc All rights reserved This product is protected by U S and international copyright and intellectual property laws Dell and the Dell logo are trademarks of Dell Inc in the United States and or other jurisdictions All other marks and names mentioned herein may be trademarks of their respective companies 2014 02 Rev AOO Contents LT PVE CRON 2 ud ta 5 Systeri Requirements armada a E EA 5 Management Station Requirements ocooccnnoconinccnnonccnoncnnnonono non n ccoo nc nnn nn nn rara rra nro 5 Intro dUCtONtO Storage AM Sic di Mace ected ae I Ea 5 Related DOCUMENTATION di elie ee 6 Locating Your Systeri Servic Tai A e 6 Contacting Dellanos een a ds Bete 7 Documentation Feedback 12 id A SR a OSA i ee ae 7 2 Hardware Installation ddan aiiiek dice Gel ees 9 Planning The Storage Configuration ccccccceccccceeesececeeeeeeceeceeneeeseeaeeeeseneeceeseaaeeeeseneeeeeesneeeeseeaeeess 9 Connecting The Storage Array oca rd a a a Masedd suds aea aaan a PEATE AEE T aiia E MEE
12. ached to and configured on a Dell PowerEdge RAID Controller PERC H800 adapter Data from virtual disks created on a PERC H800 adapter cannot be directly migrated to a PowerVault MD series storage array or to a PowerVault MD1200 series expansion enclosure connected to a PowerVault MD series storage array To attach previously configured PowerVault MD1200 series expansion enclosures to the PowerVault MD3400 or PowerVault MD3420 storage array 1 Back up all data on the expansion enclosures 2 Upgrade the expansion enclosure firmware to the latest version available at dell com support while the enclosure is still attached to the PERC H800 controller Windows systems users can reference the DUP exe package and Linux kernel users can reference the DUP bin package 3 Ensure that the storage array software is installed and up to date before adding the expansion enclosures For more information see the Dell PowerVault MD34xx 38xx Series Support Matrix at dell com support manuals a Install the software and driver package from the PowerVault MD series resource media For information about installing the software see Installing PowerVault MD Storage Software b Update the storage array RAID controller module firmware and NVSRAM to the latest versions available at dell com support c Using MDSM click Tools Upgrade RAID Controller Module Firmware Enterprise Management Window EMW 4 Stop all I O and turn off the system and attached
13. ack dell com Alternatively you can click on the Feedback link in any of the Dell documentation pages fill out the form and click Submit to send your feedback Hardware Installation Before using this guide ensure that you review the instructions in the documents e Getting Started Guide The Getting Started Guide shipped with the storage array provides information to configure the initial setup of the system e Owner s Manual The Owner s Manual provides information about important concepts to set up your storage solution See the Owner s Manual at dell com support manuals Planning The Storage Configuration Consider the following before installing your storage array e Evaluate data storage needs and administrative requirements e Calculate availability requirements e Decide the frequency and level of backups such as weekly full backups with daily partial backups e Consider storage array options such as password protection and email alert notifications for error conditions e Design the configuration of virtual disks disk groups or dynamic disk groups according to a data organization plan For example use one virtual disk for inventory a second for financial and tax information and a third for customer information e Decide whether to allow space for hot spares which automatically replace failed physical disks Connecting The Storage Array Figure 1 RAID Controller Module Ports Item Name Description
14. arlier PowerVault MD series storage arrays MDSM is compatible with both Microsoft Windows and Linux operating systems System Requirements Before installing and configuring the PowerVault MD3400 and MD3420 series hardware and software ensure that the minimum system requirements are met and the supported operating system is installed For more information see the Dell PowerVault MD34xx 38xx Series Support Matrix at dell com support manuals Management Station Requirements A management station uses MDSM to configure and manage storage arrays across the network For management station requirements see Dell PowerVault MD34xx 38xx Series Support Matrix at dell com support manuals Introduction to Storage Arrays A storage array includes various hardware components such as physical disks RAID controller modules fans and power supplies gathered into enclosures The physical disks are accessed through the RAID controller modules One or more host servers attached to the storage array can access the data on the storage array You can also establish multiple physical paths between the hosts and the storage array so that loss of any single path for example through failure of a host server port does not result in loss of access to data on the storage array The storage array is managed by MDSM running on a e Host server On a host server system MDSM and the storage array communicate management requests and event information using in
15. band or out of band connections e Management station On a management station MDSM communicates with the storage array either through an Ethernet connection to the storage array management port or through an Ethernet connection to a host server The Ethernet connection passes management information between the management station and the storage array connectivity Using MDSM you can configure the physical disks in the storage array into logical components called disk groups or dynamic disk group and then divide the disk groups into virtual disks Disk groups are created in the unconfigured capacity of a storage array Virtual disks are created in the free capacity of a disk group Unconfigured capacity comprises physical disks not already assigned to a disk group When a virtual disk is created using unconfigured capacity a disk group or dynamic disk group is automatically created If the only virtual disk in a disk group is deleted the disk group is also deleted Free capacity is space in a disk group that is not assigned to any virtual disk Data is written to the physical disks in the storage array using RAID technology RAID levels define how data is written to physical disks Different RAID levels offer different levels of accessibility redundancy and capacity You can set a specified RAID level for each disk group and virtual disk on your storage array For more information about using RAID and managing data in your storage solution se
16. click Programs and Features Select MD Storage Software from the list of programs Click Uninstall Change The Uninstall Complete window is displayed Follow the instructions on screen Select Yes to restart the system then click Done Uninstalling MD Storage Software From Windows Server Core Versions 1 2 3 4 Navigate to the Program Files Dell MD Storage Software Uninstall Dell MD Storage Software directory NOTE By default MD Storage Manager is installed in the Program Files Dell MD Storage Software directory If another directory was used during installation navigate to that directory before beginning the uninstallation procedure From the installation directory type Uninstall Dell MD Storage Software and press lt Enter gt From the Uninstall window click Next and follow the instructions on the screen Select Yes to restart the system then click Done Uninstalling MD Storage Software From Linux 1 By default MD Storage Manager is installed in the opt dell mdstoragemanager directory If another directory was used during installation navigate to that directory before beginning the uninstallation procedure From the installation directory open the Uninstall Dell MD Storage Software directory and run the file Uninstall Dell MD Storage Software exe When the uninstallation is complete it goes back to the root prompt 27 28 Load Balancing Load Balance Policy Multi path drivers select the I O
17. e the Owner s Manual at dell com support manuals Related Documentation Es NOTE For all PowerVault documentation go to dell com powervaultmanuals and enter the system Service Tag to get your system documentation K NOTE For all Dell OpenManage documents go to dell com openmanagemanuals K NOTE For all storage controller documents go to dell com storagecontrollermanuals Your product documentation includes e Dell PowerVault MD3400 3420 3800i 3820i 3800f 3820f Storage Arrays Getting Started Guide Provides an overview of system features setting up your system and technical specifications This document is also shipped with your system e Dell PowerVault MD3400 and 3420 Storage Arrays Owner s Manual Provides information about system features and describes how to troubleshoot the system and install or replace system components e Rack Installation Instructions Describes how to install your system into a rack This document is also shipped with your rack solution e Dell PowerVault MD Series Storage Arrays Administrator s Guide Provides information about configuring and managing the system using the MDSM GUI e Dell PowerVault Modular Disk Storage Arrays CLI Guide Provides information about configuring and managing the system using the MDSM CLI e Dell PowerVault MD3400 and 3420 Storage Arrays Deployment Guide Provides information about deploying the storage system in the SAN architecture e Dell PowerVaul
18. ion methods e Graphical Installation Recommended This is the recommended installation procedure for most users The installer presents a graphical wizard driven interface that allows customization of which components are installed e Console Installation This installation procedure is useful for Linux users that do not desire to install an X Window environment on their supported Linux platform e Silent Installation This installation procedure is useful for users that prefer to create scripted installations 23 Graphical Installation Recommended The PowerVault MD Storage Manager software configures manages and monitors the storage array To install the MD storage software 1 Insert the PowerVault MD series resource media Depending on your operating system the installer may launch automatically If the installer does not launch automatically navigate to the root directory of the installation media or downloaded installer image and run the md_launcher exe file For Linux based systems navigate to the root of the resource media and run the autorun file NOTE By default Red Hat Enterprise Linux mounts the resource media with the noexec mount option which does not allow you to run executable files To change this setting see the Readme file in the root directory of the installation media Select Install MD Storage Software Read and accept the license agreement 4 Select one of the following installation options f
19. k Figure 10 Four Cluster Nodes Connected to Two Controllers 19 Four cluster nodes Storage Array Management Network Figure 11 Four Cluster Nodes Connected to Two Controllers Cabling PowerVault MD1200 Series Expansion Enclosures You can expand the capacity of your PowerVault MD3400 and MD3420 storage array by adding PowerVault MD1200 series expansion enclosures You can expand the physical disk pool to a maximum of 120 slots or 192 if enabled using Premium Feature activation using a maximum of seven expansion enclosures To connect an MD1200 series expansion enclosure to your MD3400 series array 1 Connect the supported SAS cable MiniSAS HD end to the SAS OUT Port O on the MD3400 series storage array 2 Connect the other end of the SAS cable to the IN port on one of the MD1200 series Enclosure Management Modules EMM 3 To add more MD1200 expansion enclosures daisy chain them to the first expansion enclosure 20 Expanding With Previously Configured PowerVault MD1200 Series Expansion Enclosures A CAUTION If a PowerVault MD1200 series expansion enclosure that was previously attached to a PERC H800 adapter is used as an expansion enclosure to a PowerVault MD series storage array the physical disks of the expansion enclosure are reinitialized and data is lost You must back up all data on the expansion enclosure before attempting the expansion Use this procedure if your expansion enclosure is directly att
20. orage Array Management Network Figure 5 Four Hosts Connected to a Single Controller Dual Controller Configurations The following figures show two and four hosts each connected to two RAID controller modules Since each host has redundant paths loss of a single path still allows access to the storage array through the alternate path 14 HBA HBA FAFA Storage Array Figure 6 Two Hosts Connected to Two Controllers Management Network 15 Storage Array Server 3 Server 4 HBA HBA FAA Management Network Figure 7 Four Hosts Connected to Two Controllers Using Two HBAs 16 Server 1 Server 2 Server 3 Server 4 HBA HBA HBA HBA HBA HBA LEIE Storage Array Management Network Figure 8 Four Hosts Connected to Two Controllers Using One HBA The following figure shows eight hosts each connected to only one RAID controller module This configuration allows the maximum number of hosts that can be connected but provides no redundancy 17 Up to 8 hosts Server 1 Server 2 Server 3 Server 4 Server 8 HBA FA Storage Array Management Network Figure 9 Eight Hosts Connected to Two Controllers The following figures show up to four cluster nodes connected to two RAID controller modules Since each cluster node has redundant paths loss of a single path would still allow access to the storage array through the alternate path 18 Four cluster nodes Management Networ
21. perate your storage array These drivers and firmware are also available at dell com support In addition see the Dell PowerVault MD34xx 38xx Series Support Matrix at dell com support manuals for any additional settings and or software required for your specific storage array Console Installation NOTE Console installation only applies to Linux systems that are not running a graphical environment 24 The autorun script in the root of the resource media detects when there is no graphical environment running and automatically starts the installer in a text based mode This mode provides the same options as graphical installation with the exception of the MDCU specific options The MDCU requires a graphical environment to operate NOTE The console mode installer provides the option to install the MDCU However a graphical environment is required to utilize the MDCU Silent Installation Silent Installation On Windows Systems To run silent installation on a Windows system 1 Copy the custom_silent properties file in the windows folder of the installation media or image to a writable location on the host server 2 Modify the custom_silent properties file to reflect the features models and installation options to be used Then save the file 3 Once the custom_silent properties file is revised to reflect your specific installation run the following command to begin the silent installation mdss_install exe f lt nost_server_pa
22. rom the Install Set dropdown menu Full recommended Installs the MD Storage Manager client software host based storage agent multipath driver and hardware providers Host Only Installs the host based storage agent and multipath drivers Management Installs the management software and hardware providers Custom Allows you to select specific components 5 Choose whether to start the event monitor service automatically when the host server reboots or manually K NOTE This option is applicable only to Windows client software installation 6 Confirm the installation location and choose Install 7 If prompted reboot the host server after the installation completes 8 When the reboot is complete the Modular Disk Configuration Utility MDCU may launch automatically If the MDCU does not launch automatically launch it manually Ina Windows based operating system click Start Dell Modular Disk Configuration Utility Ina Linux based operating system double click the Modular Disk Configuration Utility icon on the desktop 9 Start MD Storage Manager and discover the arrays 10 If applicable activate any premium features purchased with your storage array If you purchased premium features see the printed activation card shipped with your storage array K NOTE The MD Storage Manager installer automatically installs the required drivers firmware and operating system patches hotfixes to o
23. t MD34xx 38xx Series Support Matrix Provides information about the software and hardware compatibility matrices for the storage array Locating Your System Service Tag Your system is identified by a unique Express Service Code and Service Tag number The Express Service Code and Service Tag are found on the front of the system by pulling out the information tag Alternatively the information may be on a sticker on the chassis of the system This information is used by Dell to route support calls to the appropriate personnel Contacting Dell NOTE If you do not have an active Internet connection you can find contact information on your purchase invoice packing slip bill or Dell product catalog Dell provides several online and telephone based support and service options Availability varies by country and product and some services may not be available in your area To contact Dell for sales technical support or customer service issues 1 2 3 4 Go to dell com contactdell Verify your country or region from the drop down menu at the top left corner of the page Select your support category Technical Support Customer Support Sales or International Support Services Select the appropriate service or support link based on your requirement K NOTE If you have purchased a Dell system you may be asked for the Service Tag Documentation Feedback If you have feedback for this document write to documentation_feedb
24. th gt custom_silent properties Silent Installation On Linux Systems NOTE On Red Hat Enterprise Linux 6 operating systems run the following script from the root directory to install prerequisite packages md_prereq_install sh 1 Copy the custom_silent properties file in the linux folder of the installation media or image to a writable location on the host server 2 Modify the custom_silent properties file to reflect the features models and installation options to be used Then save the file 3 Once the custom_silent properties file is revised to reflect your specific installation run the following command to begin the silent installation mdss_install bin f lt host_server_path gt custom_silent properties Upgrading MD Storage Software To upgrade from a previous version of the MDSM application uninstall the previous version see Uninstalling MD Storage Software and then follow the instructions in this chapter to install the new version 25 26 Uninstalling MD Storage Software Uninstalling MD Storage Software From Windows 1 From the Control Panel double click Add or Remove Programs Select MD Storage Software from the list of programs Click Change Remove The Uninstall Complete window is displayed Follow the instructions on screen Select Yes to restart the system and then click Done Uninstalling MD Storage Software From Windows Server GUI Versions 1 From the Control Panel double
25. units a Turn off the storage array b Turn off the expansion enclosures 5 Cable the expansion enclosures to the storage array a Connect the MiniSAS HD end of the supported SAS cabled to the SAS OUT Port O on the MD 1200 series array b Connect the other end of the SAS cable to the IN port on the MD 1200 series array 6 Turn on the attached units a Turn on the expansion enclosures Wait for the enclosure status LEDs to light blue b Turn on the storage array and wait for the status LEDs to indicate that the unit is ready Ifthe status LEDs are solid amber the storage array is still coming online Ifthe status LEDs are blinking amber there is an error that can be viewed using the MDSM Ifthe status LEDs are solid blue the storage array is ready c After the storage array is online and ready turn on any attached host systems 7 After the PowerVault MD1200 series expansion enclosure is configured as an expansion enclosure of the storage array restore the data that was backed up in step 1 After the expansion enclosures are online they can be accessed as a part of the storage array 21 Expanding With New PowerVault MD1200 Series Expansion Enclosures Perform the following steps to attach new PowerVault MD1200 series expansion enclosures to a PowerVault MD3400 or PowerVault MD3420 storage array 1 Before adding the expansion enclosure s ensure that the storage array software is installed and is up to date
Download Pdf Manuals
Related Search