User Manual
Contents
1. Up to 2000 m above sea level 2 C 40 C 80 EN IEC 61326 1 FCC Class A Class A CL 280x W 364x H 266 6kg Speed RCF switch Pulse operation Processing display Voice reminder Declaration of Conformity Construction in accordance with the following safety standards EN 61010 1 EN 61010 2 020 EN 61010 2 101 Construction in accordance with the following EMC standards EN 61326 1 FCC Part 15 Subpart B IECS 001 EN 61326 2 6 2006 Associated EU guidelines EMC directive 2004 108 EC LVD directive 2006 95 EC IVD directive 98 79 EC Installation This section describes the instructions that you should abide when install the centrifuge to ensure your safety and the optimum performance Before moving the centrifuge the rotor must be removed N WARNING e Improper power supply may damage centrifuge e Make sure the power source conforms to the required power supply before connecting Location 1 Place this centrifuge on a firm flat and level surface ensure the four feet of this centrifuge stand on the counter firmly Avoid installing on a slippery surface or surface prone to vibration 2 Ideal ambient temperature is 20 C 5 C avoid placing the centrifuge in direct sunlight if temperature exceeds 30 C 3 Keep clear of the centrifuge at least 10cm on both sides and at least 30cm behind it to guarantee the cooling efficiency 4 Keep away from heat or water to avoid sample temperature is2. Do not move or relocate the centrifuge when it is running If fluid spills in the rotor chamber please promptly clean and dry with a dry cloth to avoid sample contamination Ensure to remove any objects and fragments of the tubes dropped inside the rotor chamber before running the centrifuge Cautions with rotor 1 Always check for corrosion and damage on the rotor surface before using it Do not use the rotor if an abnormality is found Do not set the speed beyond the allowable minimum speed of the rotor kits rotor and adapters Make sure to run it below the allowable maximum speed Do not exceed the allowable imbalance Use the rotor and tubes within their actual capacities If any abnormal condition occurs during operation please stop it immediately and contact our service center Notify the service center if a warning code if displayed Vibrations are likely to damage the centrifuge contact our service center if abnormality observed Specifications Maximum speed Maximum RCF Maximum capacity Timer Noise Driving Motor Safety devices Power requirements Ambient condition Set up site Altitude Ambient temperature Humidity Excess voltage category Pollution degree Device protection class EMC Emitted interference Interference immunity Dimensions mm Weight Additional features Door interlock Over speed detector Automatic internal diagnosis Single phase 240V 50Hz 60Hz 3A Indoor only
3. Details
4. accordingly 3 End the operation 1 The centrifuge will brake when it reaches the set time or button is pressed eWhen the rotor stops rotating the centrifuge will start beeping to alert the operation has finished 2 Open the door eThe door can be released automatically when the operation has stopped SGU eWith the door closed you are able to press the button to open it eAfter ending the operation the program will store the setting parameters of this operation and 14 will recall these parameters when restarting the program 3 Open the door and take out the rotor and samples RCF operation 1 Turn onthe power switch 2 Seta RCF Relative Centrifugal Force value N CAUTION eDo not exceed the allowable maximum RCF value of the rotor and adapters SELEC ePress the select button and choose speed unit xg the speed symbol will flash into RCF value input status elf no button is pressed after the speed value has flashed after 5 seconds the input mode will be shut down eRotate program button cy to input a RCF value RCF increment is10xg 3 Set operating conditions The other operation please refer above Pulse operation This function is used to remove the residual samples adhered to the interior of the tubes or for quick Spins Note The button works only while the rotor stopped and the door is locked 1 Turn on the power switch and load the rotor to the shaft tighten the rotor lid and ma
5. change settings from small gt large gt maximum gt minimum Rotate the program button anti clockwise to change settings from large gt small gt minimum gt maximum 2 Set the time SELEC ePress select button time value flashes in the time setting mode eRotate the program button D to set running time from 30 seconds to 99 minutes eWhen the time displays HD this is a continuous running mode 2 Start the operation 1 Press button to start running eThe door must be locked before rotor starts spinning eThe timer will start once the rotor starts spinning the screen displays the remaining run time 2 View and modify the operation programs eOperation programs can be modified after the centrifuge reaches the set speed SELEC ePressing the select button returns the display to the program interface and displays SELEC setting programs Press the select button to the desired program When flashing rotate parameter button to modify values Release the button after 5 seconds and the centrifuge will return to normal operation mode and run according to the new value elf the set time value has been modified the operation time is not affected and will continue 3 Warning display elf an error occurs during the operation the centrifuge will brake to stop automatically and display the error code on the time display area The error code can be checked in the table 11 1 and corrective actions can be applied
6. Aejdsip Read the service manual Contact with service center JWI y UO paseadde apoo wey Table 11 1 Possible problems and solutions eAlarm codes E 1 E 9 are related to incorrect operation programming You can continue running the centrifuge after implementing corrective procedures How to open the door 1 Inthe case of power on A CAUTION eThe door just can be opened while the power is on and rotor stops rotating 1 Turn onthe power switch release the door automatically 2 The door will be released automatically once the operation is finished 17 OOF 3 Itis available to release the door by press button once the rotor stops 2 Inthe case of power outage The door cannot be opened automatically if there is a power outage It is available to be opened manually as follows 1 Ensure if the rotor has stopped rotating eListen carefully to ensure no rotating sound can be heard 2 Insert a screw driver into a hole to open door eHoles are located on the left and right sides of the unit elnsert a screw driver into the two holes and push forward to release the door 18 Instructions for the rotor and tubes N CAUTION eRead the instructions thoroughly to properly load and use rotor eDo not exceed the allowable maximum speed of rotor tube and adapters etc Ensure the allowable maximum speed of adapters is lower than the rotor s maximum speed 1 Rotor structure adapter screw
7. Clinical Centrifuge User Manual 400 003 311 Adapter used with 400 003 310 Rotor 400 003 312 Adapter used with 300 003 311 Adapter Please read the User Manual carefully before use and follow all operating X NX X L and safety instructions Technical specifications and outline are subject to change without prior notice Version 1 1 info labco online com www labco online com Choice Contents Introduction Warranty Delivery Safety Instructions Specifications Declaration of Conformity Installation Structure Operation Maintenance Troubleshooting Page Number 10 13 16 17 Introduction Welcome to the Clinical Centrifuge User Manual Users should read this manual carefully follow the instructions and procedures and beware of all the cautions when using this instrument Warranty Warranty of centrifuge This centrifuge is guaranteed for 12 months from the date of delivery provided that it has been operated and maintained properly Warranty of the rotor The rotor is guaranteed for 12 months from the date of delivery Do not use the rotor once it has corrosion or fatigue damage We do not guarantee this centrifuge and the rotor under the following conditions even if within the warranty period 1 Failures caused by incorrect installation 2 Failures caused by rough or improper handling 3 Failures caused by conveyance or relocation after installation 4 Failures cau
8. eed is higher Temperature of chamber is displayed and cannot be controlled Time symbol displays the ratio of working to time setting The total time setting is divided into 10 sections 11 Rotor Preparation N CAUTION e Do not overload samples which may cause leaking e Do not exceed the actual capacity allowed in the user manual Keep the tubes balanced e Although the centrifuge can accept sample balancing by eye we recommend that you keep this centrifuge in a well balanced condition to extend its life expectancy e Never intentionally run the centrifuge under an unbalanced condition even though the allowable imbalance is not exceeded Inspect the rotor Check the rotor for corrosion or scratches before using N CAUTION e f any abnormality such as corrosion or scratches are found stop using the rotor and contact Our service center e Only manufacturer s rotors must be used with the unit Symmetrically load centrifuge tubes into rotor N CAUTION Make sure the rotor lid is securely fixed on the rotor as well as the rotor and shaft are tightened Otherwise the rotor may be moved off while rotating and cause damage to the centrifuge and rotor Firmly tighten the rotor lid to the rotor 12 Operation N CAUTION Do not push or lean against the centrifuge while it is running Do not run the centrifuge when fragments or sample solutions are left in the centrifuge chamber Always keep the c
9. entrifugal chamber clean If the centrifuge makes strange noise during operation stop it immediately and contact our service center Notify them of the warning code if displayed Normal operation Turn on the power switch centrifuge will display the running interface last time after passing the self diagnostic checks e Speed 4500rpm Running time 12 minutes e The door lock is released 1 Set the operation programs SELEC Press the button to select required program The parameter can be modified when the program is flashing Rotate the program button clockwise gt to increase parameter value Rotate the program button anti clockwise F to decrease parameter value Rotate the program button C faster and the parameter value will increase faster The minimum speed increment is 100 rpm the minimum time increment is 1 second 1 Set the speed SELEC ePress the select button until the speed rpm is displayed eWhen the speed button is selected the speed symbol will flash the speed value eThe minimum speed value you can set 500rpm the minimum increment is 100 rpm eRotate program button clockwise gt to increase speed value Rotate the program button N anti clockwise L to decrease speed value eYou can speed up set the speed value by rotating program button quickly eThere is a circulating function to increase decrease the speed values Rotate the program button 13 clockwise to
10. ke sure it is in secured position and then close the door 2 The centrifuge goes into preparation mode and displays last running values 3 Press knob and hold the centrifuge will speed up to the setting speed While releasing the knob during acceleration the centrifuge will start to decelerate and stop 15 Maintenance Cleaning N CAUTION elf you do not follow the recommended instructions for cleaning or disinfecting this may damage the centrifuge 1 Centrifuge elf the centrifuge is exposed to ultraviolet rays for a long time the color of the door may be changed or the label may be peel off After using cover the centrifuge with a piece of cloth to protect it from direct exposure elf the centrifuge needs cleaning clean it with a cloth or sponge moistened with a neutral detergent solution eSterilize the centrifuge by wiping with a cloth moistened with 70 ethanol solution 2 Rotor chamber N CAUTION eDo not directly pour water neutral detergent or disinfectant solution into the rotor chamber otherwise fluids may leak into the drive units and cause corrosion or deterioration to the bearings elf the rotor needs cleaning clean with cloth or sponge moistened with a neutral detergent solution Sterilize the centrifuge by wiping with a cloth moistened with 70 ethanol solution 3 Drive shaft eWe recommend regular maintenance for drive shaft You can wipe the drive shaft with soft cloth a
11. nd then apply a thin coat of silicon grease 4 Door eClean and sterilize the door using the same method as the section 1 above 5 Rotor eTo prevent corrosion remove the rotor from rotor chamber If not in use for a long term then detach the rotor lid and turn upside down to dry the tube holes and keep clean eFor sample leaks in the rotor rinse the rotor with water Apply a thin coat of silicon grease to the rotor when it is completely dry eThe rotor should be checked every 3 months to ensure the tube and rotor holes keep are clean and apply a thin coat of silicon grease 16 Troubleshooting Possible problems and solutions This centrifuge has a self diagnostic function If a problem occurs an error warning code will be displayed on the time display screen and the operator can determine the malfunction with the alarm code below Nothing appears on the screen when Building power circuit Remove the trouble and the POWER is turned on breaker trips turn on the POWER Abnormal vibration Rotor do not match with Re Install the rotor spindle Weighting scales install Samples are imbalance symmetrically E 02 The door opened in running Close the door immediately Door fault start Close the door and then STOP The button is pressed start to operate while the door opening E 06 The setting speed exceed the Modify the speed value Set wrong speed allowable range u 1s
12. nut rubber cap mat Spindle hole Available rotors and adapters Maximum Maximum Tubes Dimension Adapters speed RCF Quantity xL mm rom xg 15mL Conical Bottom a 17x120 I 4 500 2 490 400 003 311 amp 1 5 5ml Vacutainers 12 13x82 4 500 2 218 400 003 312 13x106 400 003 311 4 500 2 490 12 4 7mL Vacutainers 400 003 311 amp 16x75 4 500 2 218 400 003 312 8 5 10mL Vacutainers 16x107 400 003 311 4 500 2 490 400 003 311 amp 12 11x66 4 500 2 218 2 7 3mL Collection Tube 400 003 312 Eee 12 15x92 400 003 311 4 500 2 490 Collection Tube Rotors and adapters 2 Notice eThe centrifuge rotor can separate samples with a density lower than 2 0g ml If the samples density is over 2 0g ml please calculate allowable speed depending on the following formula 2 0 g ml allow speed rpm max speed x 2 sample density g m1 20 Calculate RCF An RCF can be determined with the following calculation formula RCF 1 118xrxn x10 r rotating radius unit cm n rotating speed unit rom After Sales Service In order to ensure to operate centrifuge safely and efficiently it is necessary for regular maintenance If centrifuge has problems do not attempt to repair it by yourself Contact your supplier 21 Page Left Intentionally Blank 22 Page Left Intentionally Blank 23 Choice Quality Affordability info labco online com www labco online com Distributor
13. ny manner not described in this User Manual When in doubt or have any troubles with this centrifuge ASK FOR HELP e The precautions described in this User Manual are carefully developed in an attempt to cover all the possible risks However it is also important that you are alert for unexpected incidents AN WARNING This centrifuge is not explosion proof Never use explosive or flammable samples Do not install the centrifuge in or near places where inflammable gases are generated or chemicals are stored Do not place dangerous materials within 30cm of the centrifuge Prepare all necessary safety measures before using samples that are toxic radioactive or contaminated with pathogenic micro organisms Use of these is at your own risk If the centrifuge rotor and accessories that have been contaminated by solutions with toxic radioactive or pathogenic materials clean it according to the decontamination procedure as specified To avoid electrical shocks insure hands are dry before handling the power cord or turning on off the power switch For safety purposes do not enter within 30cm around this centrifuge when it is in operation While the rotor is rotating never release the door lock Unauthorized repairs disassembly or modifying the centrifuge except by our service center are strictly prohibited A CAUTION This centrifuge must be located on a firm and level table Make sure the centrifuge is horizontal before running
14. sed by unauthorised disassembly or modification 5 Failures caused by using parts of the other companies such as rotors and adapters 6 Failures caused by natural disasters including fire earthquakes and so on 7 Consumables and parts have a limited guarantee period Delivery This unit is supplied with one centrifuge unit rotor and user manual Safety Instructions Carefully read the following safety precautions for a thorough understanding e Follow the instructions and procedures described in this manual to operate this centrifuge Safely e Carefully read all safety messages in this manual and the safety instructions on the centrifuge e Safety messages are labeled as indicated below They are in combination with signal words of WARNING and CAUTION with the safety alert symbol to call your attention to items or operations that could be dangerous to you or other persons using this centrifuge The definitions of signal words are as follows WARNING Personal Danger Warning notes indicate any condition or practice which could result in personal injury or possible death CAUTION Possible damage to centrifuge Caution notes indicate any condition or practice which could result in damage or destruction of the centrifuge NOTE Notes indicate an area or subject of special merit emphasizing either the product s capability or common errors in operation or maintenance e Do not operate the centrifuge in a
15. sues or centrifuge failures Connection of the power cord and grounding N WARNING e To avoid electrical shocks ensure your hands are dry when touching the power cord e This centrifuge must be grounded properly A minimum 10A outlet providing a sufficient ground is required and this must meet local safety requirements Structure Door lock hook LCD Display Door release hole Operation panel View Air vents Power switch Rear view of the centrifuge Operation Panel Operation panel Select Select button Press the button to choose the program which you want to modify Pulse The speed can be accelerated and held at the speed Pulse button when pressing Pulse on Press the button to start running The centrifuge will nian Start Stop button brake to stop running if pressed during centrifugation Clockwise rotate to increase program values Rotate CY Parameter button anti clockwise to decrease parameter values Press the button shift between speed and RCF display Press the button to open the door The button is not 3 Door Open lock button available when the centrifuge is running Speed area Lock status Time area 8 X 100rpm The main interface Main interface In the above diagram the speed is set to be 4 500rpm the door lock is released and the running time is 12 minutes When speed symbol is rotating this indicates the centrifuge is running If the rotation is faster the sp
Download Pdf Manuals
Related Search