TracVision R5/R4 Installation Guide
Contents
1. Install Satellites on page 14 and choose USER1 or USER in Step 6 54 0359 Rev A 25 Appendix G User defined Satellites An Example of Configuring a User defined Satellite Europe The following is an example of configuring the fictional YOURSAT 101 as the USER1 configured satellite Prior to configuring this satellite or any others be certain to get the most up to date information from one of the sources previously discussed YOURSAT 101 at 7 DVB decoder Linear Polarization LNB Horizontal High Frequency 11 966 GHz Symbol Rate 27500 FEC Code 3 4 Network ID 2048 dec 0x0800 Vertical High Frequency 11 823 GHz Symbol Rate 27500 FEC Code 3 4 Network ID 2048 dec 0x0800 Vertical Low No Data Listed Horizontal Low No Data Listed Based on this information the data entered via the PC would look like this assuming that YOURSAT 101 would be Satellite A SATCONFIG USER1 7 W L DEBUGON SATCONFIG A 98 11966 27500 34 0X0800 H H 3 SATCONFIG A 98 11823 27500 34 0X0800 V H 3 SATCONFIG A 98 00000 27500 34 0X0000 V L 3 SATCONFIG A 98 00000 27500 34 0X0000 H L 3 SAVE A DEBUGOFF ZAP 54 0359 Rev A Appendix G User defined Satellites An Example of Configuring a User defined Satellite N America The following is an example of configuring the fictional YOURSAT 101 as the USER1 configured satellite P2. 3 and 4 of Mount the Antenna Standard on page 5 to complete the antenna mounting procedure 6 54 0359 Rev A Cut the Switchplate Mounting Hole 1 Finda dry flat location inside the vehicle within 27 feet of the antenna to mount the switchplate The switchplate must be easily accessible to the user 2 Using the template supplied in Appendix F on page 33 cut out the switchplate mounting hole in the mounting surface 3 82 97 mm 32 8 mm 3 32 2 5 mm dia 60mm j 2 36 Panel Cutout 16 4 maA 3 19 Switchplate Cutout Dimensions 54 0359 Rev A 81 mm A full scale panel cutout template has been provided for you in Appendix F on page 33 Be sure to consider the 28 foot length of the data power cable when choosing a location for switchplate If you require a longer cable an additional power supply MUST be used Failure to install an additional power supply when a longer cable is used can result in serious damage to the antenna unit KVH offers several cable packages 45 Cable with Power Supply KVH Part 72 0143 45 60 Cable with Power Supply KVH Part 72 0143 60 45 Cable without Power Supply KVH Part 32 0730 45 60 Cable without Power Supply KVH Part 32 0730 60 Power Supply KVH Part 19 0402 _ Wire the Antenna 1 Drill a 3 4 hole in the roof for the cable access hole Smooth the edges of
3. LNB bracket and not the LNB Ensure that the tie wrap is fastened to the LNB bracket and not the LNB 6 Reinstall the radome 7 Place the entire antenna unit into its shipping box using the original packaging material Secure the box to a pallet to ensure upright transport The repacking process is complete The TracVision R5 R4 is now ready for reshipment If you need to return the antenna be sure to obtain an RMA number from KVH s Technical Support Department first Be sure to write the number clearly on the outside of the box Shipments received without an RMA number will be returned to you at your expense 54 0359 Rev A 31 endix F Switchplate Template A ww ZG SO Z eip ww G Z Z T BE ww 09 MONS 120d IEZ i D ww g Ze ww 26 _ MASE E 54 0359 Rev A
4. VDC power input A quick tripping circuit breaker should be installed between the switchplate and vehicle power Circuit overload protection should be rated for 5 amps If vehicle power fluctuates widely or is noisy a 12 VDC 5 amp AC DC power supply should be installed KVH Part 19 0402 or equivalent Before wiring the switchplate be sure to disconnect vehicle power by removing the appropriate vehicle fuse Test the circuit to ensure that no power is present 1 Disconnect vehicle power by removing the appropriate vehicle fuse Test the circuit to ensure that no power is present 2 Connect the antenna s data power cable to the switchplate s data power connector and lock in place 12 VDC Vehicle Power Data Power Ground Receiver Ground Wire Switchplate Connections 3 Connect the receiver ground wire s to the switchplate s ground terminal as shown above 4 Connect the switchplate to vehicle power and ground as shown above 54 0359 Rev A 11 O Mount the Switchplate 1 Fit the switchplate flush into the switchplate panel cutout that you made earlier C Switchplate Cover A Panel Cutout 3 82 Screw Cavities 1 4 3 32 2 5 mm 5 32 4 mm 3 19 a 81 mm Switchplate Mounting 2 Drill out four 5 32 4 mm holes in the screw cavities in the switchplate 3 Drill four 3 32 2 5 mm holes in the mounting surface usi
5. satellite service and geographic location 1 67 N TW You can also find the skew angle for satellites in the TracVision 2 67 N 7 E R5 R4 satellite library by entering your latitude and longitude 3 67 N 30 F into the antenna You can use the grid below to determine your F EN ae approximate latitude longitude 5 63 N 7 W awe Ka 4 a on 7e ENA yf VE 4 8 57 N 7 W 9 57 N TE a 4 VAQ gt sew are PATA 11 55 N 40 E ere d 3 sy ba Hs wows gt IETARI OR o o e Cs 13 sen TE Ppa ps8 SIN a co EE j 14 50 N 22 E Ns N 15 47 N 7W 16 47 N 7 E a igdi is To determine your approximate latitude longitude match the grid above for 18 43 N 7 E your location with the corresponding grid at left 19 43 N 22 E 20 43 N 37 F Finding the Skew Angle for Satellites in the Satellite Library 21 36 N 7 W 22 36N zE 1 Type HALT then press Enter 23 36 N 22 E 2 Type DEBUGON then press Enter 24 36 N 37 E 3 Type the following command see the Key below then press Enter GPS XX D YYY E Key XX latitude 0 90 D S South or N North YYY longitude 0 180 E E East or W West 4 Type SKEWANGLE then press Enter The TracVision system will respond with the skew angle for the currently selected satellite 16 54 0359 Rev A _ Set the Skew Angle Europe only 1 Turn off the antenna and remove the appropriate vehicle fuse to disconnect power Ensure power is removed from both
6. the antenna and the receiver s or multiswitch connected to RF1 Remove the eight screws securing the radome Remove the radome and set it aside in a safe place Radome __ __ Screws LNB Rotating Plate Radome Screws Using a 9 64 allen wrench loosen the two LNB bracket screws securing the LNB in the following way loosen one screw one full turn then loosen the second screw one full turn repeat until the LNB can be rotated freely LNB LNB Bracket Screws LNB LNB Bracket Assembly Rotate the LNB to align the skew arrow with the skew angle that you determined earlier then tighten the screws in the same manner that you loosened them until the LNB no longer rotates Then turn each of the two screws an additional 1 4 turn Reinstall the radome and restore vehicle power Be sure to replace the vehicle fuse that you removed earlier 54 0359 Rev A Before servicing the antenna unit turn off the antenna and disconnect vessel power Ensure power is removed from both the antenna and the receiver s or multiswitch connected to RF1 IMPORTANT Be sure to alternate the loosening or tightening of the LNB bracket screws Turn one screw one full turn then turn the second screw one full turn until the operation is complete Failure to do so might cause unequal pressure on the LNB and impair signal reception Negative Positive Skews t Skews Align the Skew Arrow with the Sk
7. 000 29999 C FEC code e g 12 23 34 56 67 78 ID satellite network ID in hexadecimal format Ox P LNB polarization V vertical H horizontal R right L left B LNB down conversion frequency L low H high U USA D decoding type 1 DSS A 2 DSS B 3 DVB 54 0359 Rev A Appendix G User defined Satellites Transponder information has to be entered for each of the following polarizations frequencies vertical high amp vertical low horizontal high amp horizontal low or right left The TracVision R5 R4 antenna requires that the fields for all transponder categories be filled in If the selected satellite does not have information for one or more of the transponder categories default information should be entered in the fields as follows Transponder Data Default Value Frequency 00000 Symbol Rate 27500 the same value as provided for PECOJ those transponders with data Network ID 0x0000 Polarity and Band whichever combinations are not already provided 6 Type SAVE A then press Enter to save your settings or SAVE B if data is for the User2 satellite 7 Type DEBUGOFF then press Enter 8 Type ZAP then press Enter Wait one minute for the antenna to initialize One of your user defined satellites has now been added to the satellite library and is now available for tracking To begin tracking your user defined satellite s refer to
8. A Inspect Parts and Get Tools 1 Unpack the box and ensure it contains everything shown on the supplied Contents List Cables for the R5 R4 system are stored beneath the antenna unit during shipping Always lift the antenna by the 2 Carefully examine all of the supplied parts to baseplate never by the radome ensure nothing was damaged in shipment 3 Gather all of the tools and materials listed below You will need these items to complete the installation e Electric drill e 3 16 5mm 5 32 4mm and 3 32 2 5 mm drill bits e 3 4 19 mm hole saw and auger bit e 9 64 allen wrench European systems only e Phillips and Flat head screwdrivers e RG 6 or RG 11 75 ohms RF cable if installing two RF cables e Silicone sealant RTV or equivalent e 7 16 open end wrench e Construction adhesive suitable for the roof e Fasteners suitable for mounting the antenna to the roof e Augat1IT1000 crimp strip tool KVH Part 19 0242 The Flash Update Wizard is e PC with the latest version of the KVH Flash available to KVH authorized dealers Update Wizard installed through the KVH Partner Portal 2 54 0359 Rev A Plan the Installation Before you begin consider the following installation guidelines Minimize blockage The antenna needs a clear view of the sky to receive satellite TV Using the table as a guide mount the antenna a suitable distance away from obstructions on the roof such as air condi
9. ELECT to run the Check Switch function a second time 7 Once the second Check Switch function is complete ensure the TV display appears exactly as shown below Installed Switch SW42 Input 1 1 2 2 Satellite 119 119 110 110 Polarity Odd Even Odd Even Status Satellite reception verified If the TV display does not appear exactly as shown run the Check Switch function again 8 Exit the menu and allow the receiver to download the program guide 9 The procedure is complete Skip to Test the System on page 18 54 0359 Rev A 18 Install Satellites If your TracVision system is preconfigured to track your desired satellite pair see sidebar at left skip to Test the System on page 18 To select a different satellite pair you will need to connect a PC to the antenna and start the KVH Flash The TracVision system is Update Wizard This procedure requires a PC with the Flash preconfigured to track one of the Update Wizard installed The Flash Update Wizard is available following satellite pairs to KVH authorized dealers through the KVH Partner Portal Europe ASTRA1 Sat A Customers who wish to change the satellites that the TracVision HOTBIRD Sat B system tracks can visit any KVH authorized dealer distributor N America The new satellites can be configured in a just a few minutes DIRECTV_101 Sat A DIRECTV_119 Sat B 1 Connect one end of the supplied PC data cable to the DB9 mainte
10. S_72 North American or European satellite library DIRECTV 101 0 W DSS_101 Also be sure you are located within your selected DIRECTV 119 0 W DSS 119 satellite s coverage area Visit www kvh com 5 CHO footprint for satellite coverage maps If your PORGSTAR elo desired satellites are not listed you may also add any ECHOSTAR 110 0 W ECHO_110 two satellites of your choice To add satellites to the ECHOSTAR 119 0 W ECHO_119 library skip to Appendix C on page 23 EXPRESSVU820 W EXPRESSVU Type the following command see the Key below EXPRESSTV 91 0 W EXPRESSTV then press Enter PAS9 58 W PAS_9 t SATINSTALL lt sat_a_name gt lt sat_b_name gt European Satellites Key lt sat_a_name gt the name of your choice ARABSAT 26 0 E ARABSAT for Satellite A ASTRA1 19 2 E ASTRA1 lt sat_b_name gt the name of your choice ASTRAQN 28 2 E ASTRA2N for Satellite B type NONE as the name ASTRA2S 28 2 E ASTRA2S of ae B if you wish to install only one EUTELSAT W3A 7 0 E EUTEL_W3A satellite HISPASAT 30 0 W HISPASAT NOTE To receive DISH 500 service install the HOTBIRD 13 0 E HOTBIRD following two satellites ECHO_119 amp ECHO_110 HOTBIRDWB 13 0 E HOTBIRDWB Type ZAP then press Enter to restart the antenna NILESAT 101 7 0 W NILESAT Wait one minute for the antenna to initialize SIRIUS 5 0 E SIRIUS THOR 0 8 W THOR a nee pa nie arenes a ap Other Satellite Designations ere o A aes as Satellite A an 1S USER DEFINED 1 USERI e
11. TracVision R5 R4 Installation Guide These instructions explain how to install the TracVision R5 R4 satellite TV antenna system on an RV or motor coach Complete instructions on how to use the system are provided in the User s Guide and your selected receiver s user manual Step See Page 1 Inspect Parts and Get Tools 2 2 Plan the Installation 3 3 Remove the Shipping Restraints 4 4a Mount the Antenna Standard 5 4b Mount the Antenna Alternate 6 5 Cut the Switchplate Mounting Hole 7 6 Wire the Antenna 8 7 Seal the Cable Access Hole 9 8 Wire the Receiver s 10 9 Wire the Switchplate 11 10 Mount the Switchplate 12 11a Install Satellites DISH 311 Receivers Only 13 11b Install Satellites 14 12 Find the Skew Angle Europe Only 16 13 Set the Skew Angle Europe Only 17 14 Test the System 18 15 Educate the Customer 19 Technical Support TracVision Antenna lt _ Radome Vehicle Power 11 16 VDC Switchplate Baseplate Data Power RF2 Optional North American Systems Only gE Z EE Satellite Receiver 2 Satellite Receiver 1 TV2 TV1 If you need technical assistance please contact KVH Technical Support North America South America Australia Phone 1 401 847 3327 Email techs kvh com Europe Middle Fast Asia Phone 45 45 160 180 Email support kvh dk 54 0359 Rev
12. arby contact KVH Technical Support directly North America South America Australia Phone 1 401 847 3327 Monday Friday 9 00 am 6 00 pm Saturday 9 00 am 2 00 pm EST 5 GMT E mail techs kvh com Europe Middle East Asia Phone 45 45 160 180 Monday Thursday 8 00 am 4 30 pm Friday 8 00 am 2 00 pm 1 GMT E mail support kvh dk 28 Support see sidebar Replacement part numbers for units that can be serviced in the field are listed below These parts can be replaced by any KVH authorized dealer distributor Field Replaceable Units Part Name Part Number Baseplate Assembly TracVision R5 aeons Baseplate Assembly TracVision R4 aly ued Radome Assembly TracVision R5 02 0953 12 Radome Assembly TracVision R4 02 0953 11 Data Power Cable 32 0730 28 RF Cable 32 0819 28 PC Cable 32 0628 06 Main PCB 72 0211 RF PCB 72 0212 Gyro TracVision R5 Only 72 0215 System Fuses 16 0017 3150 LNB North American Systems 72 0213 LNB European Systems 72 0214 Switchplate 02 1023 01 TV SAT Switch optional 01 0245 Baseplate assembly with dual output circular LNB North American Systems Baseplate assembly with single output linear LNB European Systems Specify color when ordering 54 0359 Rev A Appendix E Reshipping Instructions If you need to repack the antenna unit for shipment the two shipping restraints tie wraps remov
13. ed during installation must be replaced The following instructions explain how to repack the TracVision R5 R4 antenna unit for shipping 1 Remove the four plugs from the forward and rear tie wrap holes on the bottom of the baseplate Forward Tie wrap Holes Rear Tie wrap Holes Antenna Baseplate Bottom View 2 Remove the eight screws securing the radome Remove the radome and set it aside Screws Radome Screws 54 0359 Rev A Appendix E Reshipping Instructions 3 Gently rotate the rotating plate until the LNB is aligned with the forward mounting plate arrow LNB Forward Mounting Plate Arrow Reshipping Orientation When moving the rotating plate by hand go slowly Hitting the mechanical stops with excessive force will damage the antenna unit 4 Thread one tie wrap through the rear tie wrap holes and through the rotating plate as shown below Fasten the tie wrap ensuring the rotating plate is secured to the baseplate oer _ s Rear y Tie wrap Forward Tie wrap LNB Bracket Tie wrap Locations 30 54 0359 Rev A Appendix E Reshipping Instructions 5 Thread a second tie wrap through the forward tie wrap holes and over the LNB bracket Fasten the tie wrap ensuring the LNB bracket is secured to the baseplate Be sure to fasten the tie wrap to the
14. ew Angle that You Determined Earlier 17 Test the System Now all you need to do is turn the system on and ensure everything works properly Follow the steps below to test the TracVision system 1 Park the vehicle in a blockage free area The antenna requires an unobstructed view of the sky to receive satellite signals 2 Turn on the receiver s and TV s For details on operating the receiver refer to your selected receiver s user manual 3 Set the switchplate s POWER switch to the ON up position to turn on the TracVision system Wait one minute for the antenna to initialize KIMI TracVision Switchplate 4 Within a few minutes a picture should appear on the TV 5 TracVision R5 Only Take a road test and verify that the antenna tracks the satellite while the vehicle is moving 6 When you have finished testing shut down the system Be sure to leave the User s Guide and the Product Registration Form inside the vehicle for the customer Refer to the User s Guide for additional information The User s Guide contains detailed information on the following e Operational instructions e Troubleshooting information e DISH 500 configuration 18 54 0359 Rev A Educate the Customer Be sure to give the manuals to the customer and explain how to use the product The customer also needs to know the following e The receiver must be activated before it can
15. late Bottom View 2 After removing the tie wraps seal the four tie wrap holes with the plugs provided in the kitpack 4 54 0359 Rev A C Mount the Antenna standard You can mount the antenna with the baseplate connectors facing the rear of the vehicle standard orientation or with the baseplate connectors facing the front of the vehicle alternate orientation Follow the steps below to mount the antenna in the standard orientation To mount the antenna in the alternate orientation skip to Mount the Antenna Alternate on page 6 1 Place the antenna on the roof on the centerline of the vehicle ensuring the arrow on the antenna s front mounting plate faces the front of the vehicle Top View Side View Front of 5 Vehicle Se ee Forward Mounting Plate Arrow J REN Baseplate Ha Mounting Plate Sef yy LS Connectors 1 of 3 OY Vehicle Baseplate Connectors Centerline Standard Antenna Orientation 2 Apply construction adhesive to the bottom of the Due to the variation in RV roof antenna s three mounting plates across all holes construction consult with the RV manufacturer to determine the safest 3 Attach the three mounting plates to the roof using fastening method 15 fasteners appropriate for the roof s construction 4 Seal all fasteners with silicone sealant or equivalent 54 0359 Rev A 5 C Mount the Antenna Alternate If you wish to mount the a
16. le on the move If you need to paint the radome use ONLY non metallic automotive paint without a primer coat Metallic paint or paint having metallic color will block satellite signals 19 Appendix A System Specifications Physical Characteristics Power 11 16 volts DC 2 5 amps nominal 3 5 amps peak Dimensions Weight LNB 32 81 cm wide x 14 8 38 cm high 33 Ibs 15 kg European system Single output N American system Dual output Maintenance Port EIA RS232 9600 bps 8 N 1 Pointing System Elevation Range 10 to 70 Azimuth Range 720 Position Repeatability 0 1 Environmental Operating Temperature 25C to 55 C 13F to 131 F Storage Temperature 40 C to 85 C 40 F to 185 F Humidity to 100 percent 54 0359 Rev A 21 Appendix B Installing 3 Receivers North American Systems Only If you need to connect three or four receivers install an active multiswitch KVH Part 19 0123 Channel Master model 6214IFD or equivalent Install the multiswitch between the antenna unit 7 and the receivers as shown below If you need to connect more Instead of grounding individual than four receivers contact KVH for additional wiring receivers you can simply ground the instructions multiswitch TracVision RF Connectors RF1 RF2 DC Power q The TracVision R5 R4 has the capability of switching from one satellite
17. lent to protect against leakage 2 Install the clamshell ventilator supplied in the kitpack over the cable access hole using three of the supplied 6 screws 6 Screws a a aco ie Clamshell aN Ar Ventilator pen Es Data Power amp RF Cables Cable Access Hole in Roof of Vehicle Installing the Clamshell Ventilator 54 0359 Rev A 9 Wire the Receiver s Do not use a screw on push on or twist on connector Low quality connectors will degrade system performance and allow water rain to penetrate the cable 10 If you cut the RF cable s be sure to use an Augat IT1000 crimp strip tool KVH Part 19 0242 to attach an F connector Augat IT1000 Crimp Strip Tool and F connector 1 Connect the RF1 cable to the receiver s Satellite In connector DL il of ra smn y A a y H Receiver Satellite In Connector Example 2 Connect one end of the supplied ground wire to any suitable screw on the receiver s rear panel with a good contact with the receiver chassis Route the other end to the switchplate location 3 If you need to connect a second receiver connect the RF2 cable and a second ground wire to the second receiver If you need to connect more than two receivers you will need to install an active multiswitch see Appendix B on page 22 54 0359 Rev A _ Wire the Switchplate The TracVision system requires an 11 16
18. nance port connector on the switchplate Connect the other end to the serial port on your PC Maintenance Port TracVision Switchplate 2 Double click the KVH Flash Update Wizard Kun shortcut on your computer s desktop to start the KVH Flash Flash Update Wizard You do not need to flash the Update Wizard antenna you will simply enter commands in the TracVision Antenna Comms window a i Type an antenna command in the Command entry area and press Enter to send to the TiacVision antenna Antenna commands can only be entered and sent when the con Pause B green Output Conmendf Enter Commands _ __ Data s AO Display If your computer does not have a TracVision Antenna Comms Window DB9 serial COM port you can use the following USB to RS232 adapter 3 Set the switchplate s POWER switch to the ON up position then turn on the receiver s Wait lOGear Part GUC232A one minute for system startup visit www iogear com 14 54 0359 Rev A commands in the TracVision Antenna Comms window 4 Type HALT then press Enter Install Satellites cta Follow the steps below to select which satellites to track Enter all Satellite Installation Names Satellite Install Name North American Satellites 5 Select any two satellite names from either the DIRECTV 72 0 W DS
19. ng the switchplate screw cavities as the template Then secure the switchplate assembly to the mounting surface using four 6 self cutting screws 4 Gently snap the switchplate cover onto the switchplate 5 Reconnect vehicle power Be sure to replace the vehicle fuse that you removed earlier 12 54 0359 Rev A Install Satellites isu 311 Receivers Only The following instructions explain how to install satellites for DISH Network service for use with DISH 311 receivers only DISH Network does not currently support the use of any other receivers for mobile customers This procedure does not require a PC To install satellites for any other receiver model proceed to Install Satellites on page 14 Ensure that the vehicle is parked in a blockage free area The antenna 1 Turn on the TV and primary receiver the receiver connected to RF1 must have a clear view of the sky to receive satellite TV 2 Set the switchplate s POWER switch to the ON up position Wait one minute for system startup 3 Using the receiver remote control go to the Point Dish Signal Strength screen press MENU 6 1 1 4 Choose Check Switch then press SELECT 5 Choose Test then press SELECT to run the Pesse A MAINTENANCE KIVIHI Check Switch function Wait 15 minutes for the antenna to install and find both DISH satellites TracVision Switchplate 6 Choose Test then press S
20. ntenna with the baseplate connectors facing the front of the vehicle alternate orientation you will need to remove the radome drill drain holes in the antenna baseplate then seal the existing factory drilled drain holes Follow the steps below to mount the antenna in the alternate orientation Alternate Orientation Only 1 Remove the eight screws and washers securing You MUST drill out the drain holes the radome to the baseplate Carefully lift the as indicated to ensure that any radome up until clear of the antenna assembly moisture that enters the baseplate is and set aside able to drain Ensure that the factory drilled holes are completely 2 Drill out three 3 16 5 mm drain holes in the sealed rear facing side of the baseplate Then plug the four existing factory drilled drain holes with silicone sealant Front of Front of Vehicle Vehicle Drill Out Alternate f Baseplate Seal Factory drilled Drain Holes Connectors Drain Holes 1 1 Drain Hole Drain Hole Angle relative to front A Angle relative to front Drain Hole Angles relative to baseplate ra MY Drain Hole i I I Vehicle Vehicle Centerline Centerline Alternate Antenna Orientation Drain Hole Locations 3 Reinstall the radome then place the antenna on the roof on the centerline of the vehicle ensuring the baseplate connectors face the front of the vehicle 4 Follow Steps 2
21. pdate Wizard as described in Install Satellites on page 14 2 Type HALT in the TracVision Antenna Comms window then press Enter FFac iston Antenna Conn a i Type an antenna command in the Command entry area and press Enter to send to the TracVision antenna Antenna commands can only be entered and sent when the icon Pause is green 0 oO Command Enter Commands lt Data Display TracVision Antenna Comms Window 54 0359 Rev A 23 24 Appendix G User defined Satellites 3 Type the following command see the Key below then press Enter SATCONFIG USERX YYY Z D L Key X 1or2 This represents the first or second user defined satellite Your TracVision system allows up to two user defined satellites YYY longitude 0 180 Z E East or W West D decoding type 1 DSS A 2 DSS B 3 DVB L LNB polarization C circular L linear The main board has now been configured to recognize the user defined satellite Next you need to configure the RF board 4 Type DEGUGON then press Enter 5 Type the following command see the Key below then press Enter SATCONFIG X N F S C ID P B D Key SATCONFIG directs data to the RF board X Satellite location A or B N 98 User defined slot 1 USER1 99 User defined slot 2 USER2 F frequency in MHz either 00000 or a range from 10700 12700 S satellite transponder symbol rate in Mbit second 01
22. receive satellite TV programming e Keep the radome installed on the antenna at all times The radome protects the antenna s internal moving parts from wind rain and debris e The antenna must have a clear view of the sky to receive satellite TV Common causes of blockage include trees buildings overpasses and mountains The TracVision antenna will not work inside a garage AE BLOCKED x Blockage Example e Heavy rain or snow may temporarily interrupt satellite reception e The antenna should be cleaned periodically Dirt buildup on the radome can affect satellite TV reception e The owner needs to register the system for product warranty validation Refer to the Product Registration Form for details or visit www kvh com register e The vehicle must be located within the selected satellite s coverage area in order to receive its satellite TV signals To view satellite coverage maps visit www kvh com footprint e Refer to the User s Guide for complete operation instructions 54 0359 Rev A IMPORTANT The customer must activate the receiver to watch satellite TV To activate a DIRECTV receiver call KVH at 1 888 584 4163 To activate a DISH Network receiver call 1 800 333 DISH To activate an ExpressVu receiver call 1 888 SKY DISH KVH offers an upgrade kit KVH Part 72 0218 that adds in motion tracking capability to the TracVision R4 allowing you to receive satellite signals whi
23. rior to configuring this satellite or any others be certain to get the most up to date information from one of the sources previously discussed YOURSAT 101 at 71 DVB decoder Circular Polarization LNB Right Frequency 11 966 GHz Symbol Rate 27500 FEC Code 3 4 Network ID 2048 dec 0x0800 Left Frequency 11 823 GHz Symbol Rate 27500 FEC Code 3 4 Network ID 2048 dec 0x0800 Based on this information the data entered via the PC would look like this assuming that YOURSAT 101 would be Satellite A SATCONFIG USER1 71 W 3 C DEBUGON SATCONFIG A 98 11966 27500 34 0X0800 R U 3 SATCONFIG A 98 11823 27500 34 0X0800 L U 3 SAVE A DEBUGOFF ZAP 54 0359 Rev A Appendix D Replaceable Parts The TracVision R5 R4 system has been designed with durability and low maintenance in mind If you experience an operating problem or otherwise require technical assistance contact your local KVH authorized dealer or distributor If an authorized dealer distributor is not located nearby contact KVH Technical If you experience an operating problem refer to the Troubleshooting section of the User s Guide If you require technical assistance please contact your local KVH authorized dealer or distributor You can find an authorized technician near you by visiting our website at www kvh com wheretogetservice If an authorized dealer distributor is not located ne
24. signated as Satellite B USER DEFNE USERN Type HALT then press Enter NONE NONE Type ZAP then press Enter Type SATINSTALL ASTRAS2S HOTBIRD then press Enter Be sure the receiver s satellite configuration matches your TracVision system s settings Your choice for Satellite A or B must be the same satellite as Receiver Alternative 1 or 2 respectively or Receiver Alternative A or B respectively based on your receiver and must be assigned the Receiver DiSEqC 1 or 2 setting respectively Refer to your selected receiver s user manual for details DiSEqC settings apply only to European systems 54 0359 Rev A tin N America you can also receive and decode signals from the DIRECTV 110 satellite if a KVH HDTV converter KVH Part 01 0260 05 is installed Unlike other N American satellites PAS9 service requires a linear European style LNB Follow the additional instructions for European systems within this guide to install the PASS satellite USER1 and USER2 will only be available if one or two user defined satellites have been added to the library see Appendix C on page 23 15 Find the Skew Angle Europe only Approximate Latitude Longitude To optimize channel reception you need to set the LNB skew angle Refer to your satellite service provider for the proper skew cnay Lantude Longitude angle for your specific
25. the hole to prevent chafing of the cable 2 Connect the antenna data power cable to the antenna s center connector and lock in place RF2 Data Power RF1 to 2nd Receiver to Switchplate to Receiver North American Systems only Antenna Baseplate Connectors 3 Connect one RF cable to the antenna s RF1 connector Hand tighten first then tighten with a 7 16 wrench for 1 4 turn 4 Slide the rubber sealing boot up the RF cable until it covers the connector This boot will help protect the connector from the elements Leave the protective cap installed on 5 North American Systems Only If you plan to the RF2 connector unless connect more than one receiver connect a second connecting a second RF cable RF cable to the RF2 connector then slide the rubber sealing boot up the RF cable 6 Route the cables down through the cable access hole in the roof Be sure to maintain a service loop approximately 8 on the roof to allow plenty of slack 7 Route the data power cable to the switchplate location inside the vehicle North American Systems Only 8 Route the RF1 cable to the receiver If you If you need to connect three or more connected a second RF cable route the RF2 cable receivers refer to Appendix B on to the second receiver page 22 8 54 0359 Rev A Seal the Cable Access Hole 1 Seal the cable access hole with a liberal amount of silicone sealant RTV or equiva
26. tioners Obstruction DAI UUMUNULUAUUUULUL Vehicle Roof Antenna Blockage Find a location on a flat part of the roof on the centerline of the vehicle The antenna must be mounted on a horizontal surface When placed flat on the mounting surface the mounting plates should be less than 7 16 above the mounting surface AE rae Z CI ao 7A Maximum Gap t Maximum Mounting Surface Slope When choosing a location for the switchplate find a dry flat location that will be easily accessible to the user Take into account cable lengths between components as well as accessibility to the equipment after installation 54 0359 Rev A Height of Minimum Distance Obstruction A from Antenna B 8 6 10 12 12 17 14 23 16 28 Any gap larger than 7 16 will warp the baseplate and seriously damage the antenna Remove the Shipping Restraints 1 At the bottom of the antenna baseplate cut the two tie wraps and pull them out of the baseplate tie wrap holes You do not need to remove the radome The tie wraps secure the antenna mechanism to prevent shipping damage You do not need to remove the radome in order to remove the shipping restraints Forward Tie wrap Holes Exercise caution when handling the antenna after removing the shipping restraints Improper handling may damage the unit Rear Tie wrap Holes Tie wrap Hole Locations on Basep
27. to another when you choose TV channels that are carried by your pno VHF UHF two selected satellites However the N n Multiswitch use of an active multiswitch interferes with communication from Out 2 Outs Optional the receivers to the antenna In this System Ground case you will need to use the 4 m tL 4 optional TV SAT Switch or the optional HDTV Converters control Receiver 2 panel To order a TV SAT Switch LJ KVH Part 01 0245 or a HDTV Converter KVH Part 01 0260 05 please call 1 401 847 3327 22 54 0359 Rev A Appendix G User defined Satellites The TracVision R5 R4 satellite library has two vacancies that you may use to program two user defined satellites in case you want to install watch a satellite not already in the KVH satellite library To install a user satellite you will need to obtain the following satellite information from your satellite service provider or from sites on the Internet such as www satcodx com e Satellite name e Satellite position longitude e Transponder information for each of the following polarizations frequencies vertical high amp vertical low horizontal high amp horizontal low or right left e Transponder information includes frequency symbol rate FEC code and network ID in hexadecimal format e Decoder type Follow the steps below to install your user defined satellite 1 Connect with the Flash U
Download Pdf Manuals
Related Search