PELLET INSERTS USER MANUAL - La Nordica
Contents
1. Y 5 cm 5 J 5 cm 5 cm 5cm 5 cm It is just as important to guarantee the minimum distance of 5 cm on both sides as shown in the figures above Reference A Hot convection air The heat accumulated inside the covering must be vented to prevent excessive overheating of the insert Reference B Forced ventilation The tangential fan distributes the heat developed by the insert into the environment Reference C Air inlet from the environment To allow air recirculation an air inlet point must be envisioned which is preferably positioned in the lower part of the structure in order to favour convection The air must be withdrawn from the machine s working environment C THE FLUE OUTLET PIPE MUST ALWAYS MAINTAIN A MINIMUM DISTANCE OF 50 MM FROM INFLAMMABLE PARTS OExtraflame ENGLISH For correct functioning of the insert during construction of the flue the measurements between the insert and internal walls of the flue must be respected figure below From the clearance measurements of the stove given in the technical features it is necessary to consider at least 50 mm of air in the upper part a2. minutes Stove off due to temperature STAND BY reached and in stand by for re To deactivate the STAND BY function see the specific chapter ignition Stove off due to an external STAND BY To deactivate the STAND BY function see the specific chapter COOLING STAND BY A new ignition is attempted when the stove has just been switched off When the stove switches off it is necessary to wait until complete fumes motor switch off and then clean the burn pot The stove can only be re ignited when these operations have been performed maximum value COOLING STDBY The stove is cooling due to black On completion of the cooling phase it will re ignite BLACK OUT out automatically Room thermostat set at minimum In this way the stove only works at 1st power independently LOW value from the power set To escape this function just raise the room temperature using button 4 and then key 2 thermostat setat The stove works at set start without ever modulating To HOT escape this function just lower the set temperature using key 4 and then key 1 OExtraflame ENGLISH ALARMS DISPLAY EXPLANATION SOLUTION On indicates the presence of an alarm Off indicates the absence of alarms indiana ai Flashing indicates the deactivation of the depression sensor P The alarm can be reset by pressing key 3 for 3 seconds only if the fumes motor has stopped and if 15 minute
3. In the event of installation with feeding kit optional the machine must not be extracted OExtraflame ENGLISH THE REMOTE CONTROL The display changes in relation to the status of the stove or the menu shown In the rest status the display shows the following items DISPLAY TIME The current time is stated The regulation of the same is found inside the weekly programmer see SET CLOCK menu ROOM TEMPERATURE Indicates the room temperature HEATING POWER indicates the functioning power It is set by the user during stove functioning STOVE STATUS Indicates the stove status After a determined amount of time the display switches off to save battery consumption It switches back on after any key is pressed BUTTON 3 ON OFF When the key is pressed for two seconds it allows the stove to be ignited and switched off If the stove is in alarm conditions therefore blocked the button allows the release and successive passage to the OFF status During programming of the user parameters it allows to escape and go back to the previous menu O BUTTON 4 SET THERMOSTAT ACCESS Buttons 1 and 2 allow to adjust room temperature BUTTON 5 SET POWER ACCESS Buttons 1 and 2 allow to regulate the functioning power from a minimum of 1 to a maximum of 5 this value is given on the upper display BUTTON 6 to go back gt BUTTON 7 ACCESS TO MENU
4. DATE SPANISH MONTH 1 12 00 99 DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE BOILING HOT STOVE DURING THE FILLING 0 DO NOT USE ANY INFLAMMABLE LIQUIDS FOR IGNITION PHASE IN THE EVENT OF CONTINUOUS NO IGNITION CONTACT AN AUTHORISED TECHNICIAN NO IGNITION ALARM FIRST IGNITION COULD EVEN FAIL AS THE AUGER IS EMPTY AND IS NOT ALWAYS ABLE TO LOAD THE BURN POT EZ WITH THE REQUIRED AMOUNT OF PELLETS ON TIME TO REGULARLY START THE FLAME IF THE PROBLEM OCCURS AFTER ONLY A FEW MONTHS WORKING CHECK THAT ROUTINE CLEANING STATED IN THE STOVE BOOKLET HAS BEEN CARRIED OUT CORRECTLY OExtraflame FUNCTIONING AND LOGIC IGNITION Once the points listed previously have been checked press key 1 for three seconds to ignite the stove 15 minutes are available for the ignition phase After ignition and having reached the control temperature the stove interrupts the ignition phase and passes to STARTING ENGLISH STARTING During the starting phase the stove stabilises combustion increasing it progressively to then start ventilation and pass on to WORK WORK During the work phase the stove reaches the set power and works to reach the set room temperature See following item ADJUSTING THERMOSTAT SETTING The room temperature can be set with button 4 access 1 and 2 adjustment from 07 to 40 C ADJUSTING POWER SETTING The power setting has 5 functioning levels by means of but
5. in the event of inadequate depression it takes the machine to alarm conditions 2 5 A 250 V fuse stoves protects the machine from m violent current drops 85 C calibrated mechanical bulb with manual rearm intervenes by blocking fuel feed whenever the pellet tank t reaches the limit of 85 C Rearm must be performed u by qualified staff and or the manufacturer s technical after sales assistance Pellet feed box temperature control probe ifthe tank over heats the machine automatically modulates to return to normal temperature values in the models envisioned Mechanical air pressure switch blocks the pellet in the a event of insufficient depression in the models envisioned INSTALLATION The installation must be in compliance with UNI 10683 2005 heat generators fed with wood and other solid fuels installation The chimneys must be in compliance with UNI 9731 1990 chimneys classification based on thermal resistance EN 13384 1 2006 Thermal and fluid dynamic calculation methods UNI 7129 point 4 3 3 Fire Department dispositions local rules and prescriptions UNI 1443 2005 chimneys general requisites UNI 1457 2004 chimneys clay ceramic flue liners NATIONAL REGIONAL PROVINCIAL AND TOWN COUNCIL REGULATIONS It is necessary to bear in mind all laws and national regional provincial and town council Standards present in the country the appliance has been installed ENGLI
6. 00 every day of the week with room temperature at 19 C excluding Saturday and Sunday 2nd time period from 15 00 to 22 00 only Saturday and Sunday with room temperature at 21 C CONTROLS PROCEDURE Press key 7 until the text SET CLOCK appears Press key 2 once the SET CHRONO text will appear ENABLE CHRONO Press key 7 ENABLE CHRONO and OFF will appear E ON Press key 2 to activate or deactivatethe U _ CHRONO function ENABLE Select ON CHRONO Press key 7 to confirm and continue programming The scrolling text START PRG1 OFF will appear 2ND TIME PERIOD SWITCH ON At this point the second time period must be programmed 1ST TIME PERIOD SWITCH ON Using keys 1 2 enter the time 08 00 which corresponds to the switch on time of the 1st time span The START PRG1 text will appear followed by the time set To confirm and continue programming press button 7 Press button 6 to go back to the previous parameter 1ST TIME PERIOD SWITCH OFF Using keys 1 2 enter the time 12 00 which corresponds to the switch off time of the 1st time period The STOP PRG1 text will appear followed by the time set To confirm and continue programming press button 7 Press button 6 to go back to the previous parameter ENABLE 1ST TIME PERIOD DAYS To do this use keys 1 and 2 in the following way Key 7 allows to scroll the various days a the text With the day of the week will appear with the condition
7. It is therefore recommended to carefully check the goods on receipt immediately informing the dealer of any damage making a note on the transport document and on the carrier s copy EXTRAFLAME S p A is not liable for any damage that can directly or indirectly affect persons objects and pets as a consequence of failure to comply with the prescriptions indicated in thismanual book ALL PARTICULARS SUBJECT TO NORMAL WEAR ARE NOT COVERED BY WARRANTY This category includes The gaskets all ceramic or toughened glass coverings and cast iron or Ironker grids the painted chrome or gold plated details the majolica the handles and the electric cables Colour variations crackles and slight size differences f the majolica parts are not a reason for claims as they are natural features of the materials themselves Parts in refractory material e Masonry work system particulars for the production of domestic hot water not supplied by EXTRAFLAME S p A water products only The heat exchanger is excluded from the warranty unless an adequate anti condensate circuit is realised which guarantees a minimum return temperature of the appliance of at least 55 C only water products FURTHER CLAUSES The warranty also excludes any calibration or regulation interventions of the product in relation to the type of fuel or the type of installation The warranty is not extended if particulars are replaced No compensation will be paid
8. and debris of any pellets Check air intake pipe and cleaning of the flow sensor o 000009 FLOW ALARM CLEAN CHECK UP BURN POT BOTTOM SHOULD THE ALARM CLEAN CHECK UP BE TRIGGERED MAKE SURE THAT THE BOTTOM OF THE BURN POT IS FREE OF RESIDUES OR SCALES THE HOLES AT THE BOTTOM MUST BE COMPLETELY FREE TO GUARANTEE CORRECT COMBUSTION or THE ABOVE INDICATED PELLET FEED REGULATION FUNCTION CAN BE USED TO ADJUST COMBUSTION BASED ON THE DESCRIBED REQUIREMENTS IF THE ALARM PERSISTS AND THE ABOVE LISTED CONDITIONS HAVE BEEN CHECKED CONTACT THE QUALIFIED AFTER SALES ASSISTANCE CENTRE OExtraflame ENGLISH DISPLAYS DISPLAY REASON SOLUTION OFF Stove off START The start phase is in progress PELLET FEEDING The feeding of the pellet during the ignition phase is in progress IGNITION The ignition phase is in progress START UP The start phase is in progress WORK ne work phase is in MODULATION The stove is modulating BURN POT CLEANING The automatic burn pot cleaning is in progress The automatic burn pot cleaning not in 1st power is performed at pre established intervals of continued working When the stove is switched off final cleaning is in progress The final cleaning phase lasts about 10 thermostat waiting for re ignition FINAL CLEANING
9. for the time the product is inefficient This warranty is valid only for the purchaser and cannot be transferred RECOMMENDED INSPECTION WITH PAYMENT EXTRAFLAME S p A recommends that the functional inspection of the product is performed by a qualified Technical After Sales Centre which will supply all information for correct use WARRANTY INTERVENTIONS The request for intervention must be sent to the dealer or after sales assistance Centre The warranty intervention envisions the repair of the appliance without any charge as provided by the law in force LIABILITY EXTRAFLAME S p A does not grant any compensation for direct or indirect damage caused or depending on the product LAW COURT The Vicenza Law Court is elected as the competent court for any disputes QExtraflame OExtrafiame Riscaldamento a Pellet EXTRAFLAME S p A Dell Artigianato 12 36030 MONTECCHIO PRECALCINO VI ITALY FN 39 0445 865911 E 39 0445 865912 info extraflame it www lanordica extraflame com Extraflame reserves the right to vary the features and data shown in this booklet at any time and without prior notice in order to improve its products This manual cannot be considered as a contract for third parties This document is available at www extraflame it support 004275903 Manuale Utente Inserti a pellet Ic Mini Mini Crystal P80 001
10. they are made must constitute a self supporting construction with respect to the heating block and not be in contact with it The cross members and finishings in wood or combustion materials must be positioned outside the hearth radiation area or adequately insulated If coverings in combustion material or sensitive to heat exist in the space above the generator an insulating and non combustible protection diaphragm must be inserted Elements in combustible or inflammable material like wooden furniture curtains etc directly exposed to the hearth radiation must be positioned at a safe distance The appliance installation must guarantee easy access for cleaning the appliance itself discharge gas pipe and flue CHIMNEY CAPS DISTANCES AND POSITIONING Roof inclination Distance between the ridge and the chimney Minimum chimney height measured from outlet m H m o lt 1 85 0 50 m over the ridge Ls gt 1 85 1 00 m from roof 5 lt 1 50 0 50 m over the ridge gt 1 50 1 30 m from roof m 1 30 0 50 m over the ridge gt 1 30 2 00 m from roof SU lt 1 20 0 50 over the ridge gt 1 20 2 60 m from roof COMFORT MINI P80 MINI CRYSTAL USED INSTALLATION The insert is supplied with an iron sliding base that allows to install it in a pre existing flue This sliding base allows the easy extraction of the insert both for pellet feeding inside the feed box and for any maintenance or c
11. to have verified that the plant has been realised in compliance with the Standard in force by professionally qualified staff in compliance with the Standards in force and to have checked the good functioning of the installed product Once this has been verified the After Sales Centre will supply all the information for its correct use filling in and delivering a copy of the document which certifies the warranty undersigned by the client EXTRAFLAME S p A assures that all its products are manufactured with top quality materials and with manufacturing techniques which guarantee total efficiency If during normal use of the product defective or badly working particulars should be detected the replacement of such particulars will be free of charge ex dealer who made the sale TERRITORIAL EXTENSION OF THE WARRANTY Italian territory VALIDITY THE WARRANTY IS CONSIDERED VALID ON THE CONDITION THAT 1 The purchaser forwards theinspection report and warranty validation copy 2 filled in completely within 8 days from the date of validation of the warranty The purchase date must be validated by the possession of a valid fiscal document issued by the dealer 2 The appliance is used as prescribed in the instructions manual provided with all products 3 The boiler is installed in compliance with the Standards in force with regard to the prescriptions contained in the installation use and maintenance manual relating to the product by qualified sta
12. 0 45 le Inspection Inspection Appliance connection to the flue and combustion products evacuation The flue must receive the discharge from only one heat generator Direct discharge towards closed spaces is forbidden even with clear sky The direct discharge of the combustion products must be at roof and the smoke pipe must have the features provided in the Chimney or individual flue section CHIMNEY CAP The chimney cap must comply with the following requisites have an internal section equivalent to that of the chimney have useful outlet section not lower than double the chimney internal section be built in order to avoid rain snow foreign bodies penetrating the chimney and so that in the event of winds in any direction and inclination the discharge of the combustion products is assured be positioned in a way to guarantee an adequate dispersion and dilution ofthe combustion products and however outside the reflux area in which the formation of counterpressures occurs Such area has different dimensions and configuration depending on the covering inclination angle It is therefore necessary to adopt the minimum heights indicated in the figure layouts below The chimney cap must not have mechanical intake means FLAT ROOF SLOPING ROOF Z REFLUX AREA OExtraflame ENGLISH CONNECTION TO EXTERNAL AIR INLETS The a
13. Allows to enter and set the user ES parameters DISPLAY ICONS KEY It indicates functioning of the fumes motor Off fumes motor not working On fumes motor working G It indicates weekly programming functioning Indicator on Weekly programming on Indicator off Weekly programming off It indicates functioning of the tangential fan Indicates the stby function C 009 Off not working STBY Off Stby deactivated On working On Stby activated Additional external thermostat input status Indicates Ue presence oran alarm On indicates the presence of an alarm Off open contact em Off indicates the absence of alarms On closed contact 5 It indicates functioning of the pellet feed motor Indicates the room T status GE Off pellet feed motor deactivated On Room T lower than desired setting On pellet feed motor active Off room T higher that set point set Feed box probe Off normal functioning On anomaly Indicates the stove modulation On the stove is working at the set power Off the power at which the stove is working is different to the power set the stove is modulating for various reasons OExtraflame ENGLISH GENERAL FEATURES The user interface is provided with a backlit LCD display The backlighting lasts about 4 seconds Display backlighting time can be set Press keys 1 and 7 simultaneously to access After having accesse
14. ESTAL ASSEMBLY OPTIONAL Position the base in the desired point and use the feet to adjust the desired height the bolts are positioned in the four external sides of the pedestal in the lower part Envision a current socket on the rear of the pedestal so that the plug is accessible once installation is completed Fix the pedestal to the floor using strong steel plugs with a diameter of 8 mm Fix the sliding base to the frame using bolts Connect the flue gas exhaust pipe and the air vent as stated in the previous paragraph Take the insert incline it in a way that the wheels insert into the relative rails make it run until the flue gas auger is completely inserted into the flue gas conveyor box Finally open the fire door and use the supplied Allen key to turn the screw at the bottom left corner clockwise To understand whether the insert is correctly attached to the base connect the plug to the socket and make sure the display switches on Mount the hopper support for the pellet and insert it into the relevant coupling OExtraflame ENGLISH Note If our pedestal is used a slot must be created in the flue that allows to check the pellet level in the feed box thus preventing escape during filling COMPONENT DESCRIPTION A Height adjustable pedestal suc B Lateral feed hopper C Adjustable hopper support HE Adjust the height and the inclination of the hopper on the basis of the flue that will be built THE HOPPER
15. OCK appears Press key 2 several times to reach SET USER Confirm using key 7 Press key 2 several times to reach STAND BY By means of key 2 select ON Press key 6 several times to confirm and exit the Menu 6 QEXtraflame ENGLISH KEYS LOCKED The function allows to lock the display keys like mobile phones Follow these instructions to activate key locking Press key 7 fora few seconds until the text SET CLOCK appears Press key 2 several times to reach SET USER Confirm using key 7 Press key 2 several times to reach KEYS LOCKED By means of key 2 select ON To activate or deactivate the key Press key 6 several times to confirm and exit the Menu lock press key 6 for 5 seconds 060 6 ROOM PROBE The function allows to select between the probe integrated in the remote control and the additional room probe optional RESET Allows to reset all values modifiable by the user to the default values The modified data are SET TEMPERATURE 35 C Press key 7 fora few seconds until the text SETPOWER 5 SET CLOCK appears ENABLE CHRONO OFF Press key 2 several times to reach SET USER START PRG1 OFF Confirm using key 7 STOP PRG1 OFF Press key 2 several times to reach RESET MONDAY PRG1 OFF means of key 2 select ON Ar a SRRAMETCESORE Press key 6 to confirm and exit the Menu STAND BY OFF STOVE STATUS The values will appear in order that concern the foll
16. OFF Use key 1 or 2 to enable disable ON OFF all days MONDAY PRG1 SETTING TEMPERATURE OF FIRST TIME PERIOD Press key 7 the text SET PRG1 and the temperature will appear Press key 1 or 2 to set the temperature of 19 as in the example Press key 7 to confirm and continue programming The text START PRG2 OFF will appear The sequence to be followed is the same and is repeated as for the 1ST TIME PERIOD SWITCH ON On this occasion it is only necessary to enter the time for example start at 15 00 and Stop at 22 00 and to activate the days Saturday and Sunday by setting them at ON The temperature in SET PRG2 must be set as for example 21 C WHEN THE WEEKLY PROGRAMMER IS ACTIVE A BOX OF THE RELATIVE ICON WILL APPEAR ON THE O CONTROL BOARD OExtraflame CLEANING UNDER USER S RESPONSIBILITY Some images could be offset from the original model DAILY Burn pot remove the burn pot from the relevant compartment and free the holes using the appropriate fire irons supplied remove the ash from the burn pot using a suction device Suck the ash deposited in the brazier compartment Scrapers Cleaning of the heat exchangers allows to guarantee constant heat output through time This type of maintenance must be performed at least once a day To do this just use the relevant scrapers positioned in the upper part of the stove moving them up and down several times Scrapers WEEKLY Cleaning ash colle
17. OPTIONAL The appliance can check the room temperature using an additional external thermostat optional After ignition pressing key 1 or via chrono mode the stove will work to reach the setting displaying WORK closed contact When the room temperature has been reached open contact the stove will go to minimum displaying MODULATION TO INSTALL AND ENABLE IT A mechanical or digital thermostat is required Switch the appliance off by removing the insert and cutting power Remove the plug from the socket Referring to the figure to the side connect the two thermostat wires potential free contact no 220 V on the relative terminals at the back of the machine one red and the other black with the label STBY Power the stove Press key 4 and by means of key 1 set the temperature at LOW 9 The stove is now configured correctly It will work controlling the additional external thermostat ADDITIONAL EXTERNAL THERMOSTAT OPTIONAL AND STAND BY FUNCTION The Stby function is used if immediate stove switch off is required when temperature has been reached QEXxtraflame ENGLISH STBY FUNCTION SET AT OFF FACTORY SETTING If the STBY function is not active OFF if the stove reaches the room temperature set it will go to minimum modulating and displaying MODULATION When the room temperature is lower by 2 C than the setting the stove will start to work again at the power set on the display showing W
18. ORK STBY FUNCTION SET AT ON With the stby function set at ON when the additional thermostat has a request closed contact the stove switches on automatically and works to reach the temperature set showing WORK When the additional external thermostat detects that the temperature has been reached open contact the stove switches off after a delay pre set in the factory displaying STAND BY EXT FOLLOW THESE INSTRUCTIONS TO ACTIVATE STBY Press key 7 for a few seconds until the text SET CLOCK appears Press key 2 several times to reach SET USER Confirm using key 7 Press key 2 several times to reach STAND BY By means of key 2 select ON Press key 3 several times to confirm and exit the Menu 0 6 6 THE FIRST IGNITION MUST ALWAYS BE PERFORMED MANUALLY FROM THEN ON IT WILL BE MANAGED Ros AUTOMATICALLY WITH THE ROOM PROBE The STBY function can be set at ON or OFF using the procedure that will be described INSTALLATION AND ACTIVATION OF ROOM PROBE OPTIONAL It is also possible to install an optional room thermostat directly on the stove Contact an authorised technician to install and activate it NOTE C ONLY ONE PROBE AT A TIME CAN BE USED ACTIVATE JUST ONE CONFIGURATION 1 REMOTE CONTROL PROBE 2 ROOM PROBE OPTIONAL NTC 3 ROOM THERMOSTAT OPTIONAL USER MENU PELLET FEED ADJUSTMENT The following menu allows the adjustment of pellet feed as a percentage If the stove has functioning problems owing t
19. QeExtraflame Riscaldamento a Pellet PELLET INSERTS USER MANUAL IC MINI MINI CRYSTAL P80 ENGLISH INGLESE OExtraflame OExtraflame We thank you for having chosen our company our product is a great heating solution developed from the most advanced technology with top quality machining and modern design aimed at making you enjoy the fantastic sensation that the heat of a flame gives in complete safety Extraflame S p A ENGLISH 4 WARNINGS SAFET O II me ROUTINE MAINTENANCE rasp SAFETY DEVICE Sa A INSTALLATION cca INSTALLATIONS ALLOWED iii INSTALLATIONS NOT ALLOWED CONNECTION TO THE SMOKE EVACUATION STE ns 6 SMOKE CHANNEL OR FITTINGS iaia 6 CHIMNEY OR INDIVIDUAL FLUE 7 CHIMNEY 8 CONNECTION TO EXTERNAL AIR INLETS csssssscescsssscssscsnsscssscsnsscsnsssneseensesneneenee 9 INSULATION FINISHINGS COVERING AND SAFETY 5 9 COMFORT MINI P80 MINI CRYSTAL USED INSTALLATION cerne enero eo eooeo toronto tentato totos to seen ce tenen cenenenseneesenezsenennene 9 ASSEMBEEFWITH SEIDINIG BASE nadia 10 PEDESTAL ASSEMBLY OPTIONAL CE 10 FRONT PELLET FEEDING KIT OPTIONAL scscscscsssscecs
20. SH GLOSSARY CLOSED HEARTH APPLIANCE Heat generator which opening is only allowed through the loading of the fuel during use BIOMASS Biological material excluding the material incorporated in geological formations and transformed into fossils BIOFUEL Fuel produced directly or indirectly by biomass CHIMNEY Vertical pipe with the aim of collecting and expelling the fuel products coming from only one appliance at a convenient height from the ground SMOKE CHANNEL OR FITTING Pipe or connecting element between heat generator appliance and chimney to evacuate combustion products INSULATION Group of set ups and materials used to prevent the transmission of heat through a wall that separates rooms with different temperatures CHIMNEY CAP Device positioned at chimney peak to ease the dispersion of combustion products into the atmosphere CONDENSATE Liquid products that form when the combustion gas temperature is lower or equal to the water dew point HEAT GENERATORS Appliance which allows to produce thermal energy heat through the rapid transformation via combustion of the chemical energy of the same fuel GATE VALVE Mechanism for modifying the combustion gas dynamic resistance COMBUSTION PRODUCT EVACUATION SYSTEMS Flue gas exhaust system independent from the appliance constituted by a fitting or smoke channel chimney or individual flue and chimney cap FORCED DRAUGHT Air circulation by means of the fan ac
21. SUPPORT CAN BE MOUNTED C EXCLUSIVELY ON THE RIGHT SIDE OF THE INSERT C THE INSERT MUST LIE AT LEAST 1 CM ABOVE THE FIRE SURFACE IN COVERING MARBLE FRONT PELLET FEEDING KIT OPTIONAL The optional pellet feeding kit allows to feed pellets from the front inside the tank without having to extract the insert operation that requires machine switch off Further information on the accessories is available on the website www extraflame it support in the category accessories AIR CIRCULATION PIPES It is necessary to create air recirculation inside the structure that covers the insert for correct functioning This prevents the appliance from over heating To guarantee this just realise one or more openings in the lower part and in the upper part of the covering The following measurements must be respected LOWER PART COLD AIR INLET WITH TOTAL MINIMUM SURFACE 550 UPPER PART HOT AIR OUTLET WITH TOTAL MINIMUM SURFACE 500 C THIS VENTILATION SYSTEM IS TOTALLY INDEPENDENT FROM THE AIR INTAKE FOR COMBUSTION To protect from any over heating the Comfort P80 is supplied with a probe that analyses the temperature inside the structure and intervenes by reducing the functioning power OExtraflame ENGLISH COMFORT MINI COMFORT MINI CRYSTAL COMFORT P80 e i D gt D Q IN _ Hmmm Minimum 5
22. ch to 1 The stove switch powers the stove board The stove remains off and a first screen appears on the panel reading OFF FILL THE FEED BOX WITH PELLETS Open the feed box lid and load the pellets using a scoop e Pay attention not to drop pellets laterally or inside the stove For further information see the previous chapter pellets and feeding THE LID OF THE PELLET CONTAINER MUST ALWAYS BE CLOSED IT MUST ONLY BE OPENED DURING THE FUEL FEEDING PHASE C THE BAGS OF PELLETS MUST BE KEPT AT LEAST 1 5 METRES FROM THE STOVE IT IS RECOMMENDED THAT THE FEED BOX IS ALWAYS HALF FULL MAKE SURE THE APPLIANCE IS OFF BEFORE FILLING THE PELLET TANK ADJUSTING TIME DAY MONTH AND YEAR ADJUSTING LANGUAGE CONTROLS PROCEDURE CONTROLS PROCEDURE Press key 7 for a few seconds until the Press key 7 for a few seconds until the SET CLOCK appears text SET CLOCK appears Confirm using key 7 Press key 2 twice until set Language Use key 1 or3 to assign the day Confirm using key 7 Press key 7 to confirm and continue Select the language using key 3 Use the same procedure 7 to advance 1 and 2 to Press key 3 several times to confirm and exit the set to adjust the hour minutes day Menu month and year Press key 3 several times to confirm and exit the Menu SET CLOCK ITALIAN DAY MON TUE WED SUN ENGLISH HOURS 0225 LANGUAGE GERMAN MINUTES 00 59 FRENCH
23. ctor trays The ash collector trays indicated in the figure below must be emptied when required using a suction device Ash collector poe trays Make sure that the ash is completely cold before emptying it into a suitable container The Chimney sweep bin is an accessory available from the company ENGLISH MONTHLY Cleaning the heat exchanger The heat exchangers chamber must be cleaned every month as the soot deposited on the rear of the cast iron hearth wall blocks the regular flow of fumes To access the heat exchangers remove the central piece from the hearth wall following the operations described below Remove the burn pot from its location Turn the lockbolt by 180 Lockbolt Hold the extractable cast iron and pull it downwards Finally slide it from the combustion chamber by pulling it towards yourself paying attention to the 2 lateral cast iron hooks below Once the heat exchanger compartment can be accessed use the supplied fire irons to remove and scrape the soot deposited and only then use the suction device to completely remove the ash When cleaning has been completed re position the extractable cast iron with the opposite movement used to remove it When the hearth wall has been positioned turn the lockbolt to take it to it
24. d use keys 1 or 2 to select the time in seconds from 0 to 9 Direct controls for ignition switch off power change room temperature Weekly programming setting The insert emits an acoustic Beep signal every time the keys are pressed CONFIGURATION OF REMOTE CONTROL THE REMOTE CONTROL IS ALREADY CONFIGURED WITH THE UNIT The remote control operates in 2 ways 0 SHOULD THERE BE ANOTHER via radio IC MINI CRYSTAL OR P80 TO via cable when connecting the cable no configuration is necessary Cor AVOID INTERFERENCE A NEW CONFIGURATION MUST BE DONE THE CODING PROCEDURE ISTHE FOLLOWING MODIFYING ONE THE TWO 1 Cut power from the insert INSERTS 2 Press keys 1 and 2 simultaneously 3 By means of buttons 1 or 2 or selecting the UNIT from 0 to 7 the unit selected must be different than the other insert 4 Power the insert An acoustic signal Beep will be emitted within 10 seconds keep the key 3 pressed to confirm The remote control will indicate UNIT XX LOADED The insert is ready and correctly configured If the communication between remote control and chimney is very disturbed or imprecise the remote control can be connected directly to the appliance via cable as illustrated in the figure below Comfort Mini Comfort Mini Crystal Comfort P80 TYPE AND REPLACEMENT OF BATTERIES The batteries are housed in the lower part of the remo
25. e combustion products and any condensate have mainly vertical progress with deviations from the axis not higher than 45 be adequately distanced from fuel or flammable materials through air space or opportune insulation have preferably circular internal section the square or rectangular sections must have round corners with a radius not lower than 20 mm haveconstant internal section free and independent haverectangular section with max ratio between the sides of 1 5 Itis recommended that the smoke pipe be equipped with a collection chamber for solid materials and any condensate situated under the smoke channel inlet so that it can be easily opened and inspected from airtight door REFERENCES INFLAMMABLE OBJECTS NON INFLAMMABLE OBJECTS A 200 mm 100 mm B 1 500 mm 750mm 200 mm 100 mm zz Minimum 80 cm S floor protection y Flue nan B C Airinlets Inspection 4 Chimney cap me Zu 3 596 il Inspection Flue N Inspection N OExtraflame ENGLISH 2 Za lt 3m ES External pipe that is isolated 45
26. e majolicas are top quality artisan products and as such can have micro dots crackles and chromatic imperfections These features highlight their valuable nature Due to their different dilation coefficient enamel and majolica produce crackling which demonstrate their effective authenticity To clean the majolicas it is recommended to use a soft dry cloth If a detergent or liquid is used the latter could penetrate inside the crackles highlighting the same 9 9 9 9 ROUTINE MAINTENANCE Based on the Decree 22 January 2008 n 37 art 2 routine maintenance means interventions aimed at reducing degradation from normal use as well as dealing with accidental events entailing the need of first interventions which however do not modify the structure of the system upon which one is intervening or its intended use according to the prescriptions foreseen by technical standards in force and by the manufacturer s use and maintenance booklet OExtraflame SAFETY DEVICES SAFETY DEVICES STOVES KEY PRESENT NOT PRESENT Circuit board intervenes directly by sending the product into alarm conditions until complete cooling in the case of breakage of flue gas motor pellet feed motor breakage black out if more than 10 seconds no ignition Insert blocking micro switch if the end run micro switch warns that the insert is not blocked electric energy does not pass to power it Electronic pressure switch
27. ff in possession of the legal requisites M D n 37 dated 22 January 2008 4 client is in possession of the documentation which certifies its eligibility filled in in all its parts A INSTALLATION REPORT filled in by the installer B INSPECTION REPORT AND VALIDATION OF THE WARRANTY Filled out by the client dealer and a qualified technical assistance centre 5 The warranty document filled in and accompanied by the purchase fiscal document issued by the dealer must be kept and shown to the authorised technician in the event of intervention THE WARRANTY IS NOT CONSIDERED VALID IN THE FOLLOWING CASES 1 The warranty conditions described above have not been respected 2 Installation has not been performed with respect to the Standards in force regarding the provisions described in the manual book provided with the appliance 3 Negligence of the customer due to lack of or incorrect maintenance of the product 4 Presence of electric and or hydraulic plants that do not comply with the standards in force 5 Damages deriving from atmospheric chemical electro chemical agents improper use of the product modifications and tampering with the product inefficacy and or unsuitability of the flue and or other causes not deriving from the manufacture of the product OExtraflame ENGLISH 6 Combustion of materials not compliant with the types and quantities indicated in the manual book supplied 7 damages caused by transport
28. flame ENGLISH ROOM PROBE AND STAND BY FUNCTION The STBY function is used if immediate stove switch off is required when the set temperature has been reached In the factory the STBY function is always set at OFF STBY indicator light off STBY FUNCTION SET AT OFF FACTORY SETTING If the STBY function is not active OFF if the stove reaches the room temperature set it will go to minimum modulating and displaying MODULATION When the room temperature is lower by 2 C than the setting the stove will start to work again at the power set on the display showing WORK STBY FUNCTION SET AT ON When the STBY function is activated ON the stove upon reaching the set room temperature and exceeding it by 2 C will switch off after a delay set in the factory displaying STAND BY When the room temperature is 2 C less than the setting the stove will start to work again at the set power displaying WORK FOLLOW THESE INSTRUCTIONS TO ACTIVATE STBY Press key 7 for a few seconds until SET CLOCK appears Press key 2 several times to reach SET USER Confirm using key 7 Press key 7 several times to reach STAND BY By means of key 2 select ON Press key 3 several times to confirm and exit the Menu 9 999 The STAND BY function is activated THE FIRST IGNITION MUST ALWAYS BE PERFORMED MANUALLY FROM THEN ON IT WILL BE MANAGED AUTOMATICALLY WITH THE ROOM STOVE FUNCTIONING WITH ADDITIONAL EXTERNAL THERMOSTAT
29. leaning at the end of the season If there is no pre existing flue one can be built using the insert holder pedestal optional kit in fact the latter fixes the insert to the floor Component description A Primary air intake pipe B Flue exhaust pipe C Adaptation frame D Sliding base and rails E Socket OExtraflame ENGLISH ASSEMBLY WITH SLIDING BASE Take the sliding base and position it in the pre existing flue Use chalk to mark the blocking holes of the base on the flue surface Drill 8 mm holes for the steel expansion inserts Make a hole measuring 60 mm in correspondence with the air intake Envision a current socket on the rear of the insert so that the plug is accessible once installation is completed Fix the base using the locking screws Create a flue exhaust and socket connection respecting the points described previously Take the insert incline it in a way that the wheels insert into the relative rails make it run until the flue gas auger is completely inserted into the flue gas conveyor box Primary air intake PRIMARY AIR VENT THE AIR VENT MUST BE MADE OUTSIDE THE FLUE AS C IT MUST NOT SUCK HEATED AIR PERFORMING THIS CONNECTION INCORRECTLY CAN JEOPARDISE FUNCTIONING OF THE PRODUCT PED
30. n pipes Should these appliances bein rooms adjacent communicating with the installation room the simultaneous use of the heat generator is forbidden where a risk exists of one of the two rooms being placed in depression respect to the other CONNECTION TO THE SMOKE EVACUATION SYSTEM UNI 10683 2005 Standard SMOKE CHANNEL OR FITTINGS To mount the smoke channels non flammable elements will have to be used ideal for resisting combustion products and their eventual condensing The use of flexible metal and asbestos cement pipes to connect the appliances to the flue is forbidden even for pre existing smoke channels There must be continuity between the smoke channel and the flue so that the flue does not lean on the generator The smoke channels must not cross rooms where the installation of the combustion appliances is not allowed The mounting of the smoke channels must be carried out in order to guarantee smoke seal for the appliance functioning conditions limit the forming of condensate and avoid it being transported towards the appliance The mounting of horizontal routes must be avoided For appliances where ceiling or wall non coaxial discharges with respect to the appliance combustion product outlet have to be reached the direction changes will have to realised using open bends not greater than 45 see figures below For the heat generator appliances equipped with electric fan for expelling combustion products the instructio
31. nd on the 2 sides P80 MINI CRYSTAL r ur 9 86 mm b 50 mm gt nie EER INSERT BLOCKING AND RELEASING SAFETY DEVICE Open the fire door and use the supplied Allen key to turn the screw at the bottom left corner clockwise To understand whether the insert is correctly attached to the base connect the plug to the socket and make sure it works with the supplied remote control INSERT EXTRACTION The extraction of the insert allows to load pellets inside the feed box and to perform routine maintenance cleaning the ash pipe at the end of the year or extraordinary maintenance replacement of mechanical parts if the product should break Follow this procedure to extract the insert Open the fire door and use the supplied Allen key to turn the screw at the bottom left corner anticlockwise Using the relevant fire irons pull the machine towards yourself until it blocks automatically OExtraflame ENGLISH MOUNTING THE FRAMES Front frame N B Any wooden beams situated above the insert must be Side frames protected with non inflammable material Frame assembly 15 impo
32. nect twist electric cables leaving the stove even if disconnected from the electric power supply mains It is advised to position the power supply cable in a way that it does not come into contact with hot parts of the appliance The power supply plug must be accessible after installation Do not close or reduce the dimensions of the airing vents in the place of installation The airing vents are indispensable for correct combustion Do not leave the packaging elements within reach of children or unassisted disabled persons The hearth door must always be closed during normal functioning of the product When the appliance is functioning and hot to the touch especially all external surfaces attention must be paid Check for the presence of any obstructions before switching the appliance on following a prolonged standstill period The stove has been designed to function in any climatic condition also critical In particularly adverse conditions strong wind freezing safety systems may intervene that switch the stove off If this occurs contact the technical after sales service and always disable the safety system If the flue should catch fire be equipped with suitable systems for suffocating the flames or request help from the fire service This appliance must not be used to burn waste Do not use any inflammable liquids for ignition During the filling phase do not allow the bag of pellets to come into contact with the product Th
33. ns below must be followed Insulating R product fe lt 45 lt 45 Flue A _ Inspection NW The horizontal routes will have to have a minimum upward slope of 3 The length of the horizontal route must be minimal and however not longer than 3 metres The number of direction changes including the one for effect of using the T element must not be more than 4 In any case the smoke channels must seal the combustion and condensate products and be insulated if they pass outside the installation room The use of counterslope elements is forbidden The smoke channel must allow the recovery of soot or be brushable The smoke channel must have constant section Any section changes are only allowed at the flue coupling It is forbidden to have other air supply channels and pipes for plant engineering especially if over sized transit inside the smoke channels The mounting of manual draught adjustment devices on forced draught appliances is forbidden OExtraflame ENGLISH CHIMNEY OR INDIVIDUAL FLUE The chimney or individual flue must respond to the following requisites seal the combustion products be waterproof and adequately insulated in line with the use conditions be realised with materials which resist the normal mechanical stress heat action of th
34. o persons animals and objects due to installation adjustment and maintenance errors and improper use Installation must be performed by qualified staff and or technical after sales assistance which assumes complete responsibility for the definitive installation and consequent good functioning of the product installed It is necessary to bear in mind all laws and national regional provincial and town council Standards present in the country the appliance has been installed Extraflame S p A cannot be held responsible for the failure to comply with such precautions After removing the packaging ensure that the content is intact and complete If not so contact the dealer where the appliance was purchased All electric components that make up the product must be replaced with original spare parts exclusively by an authorised after sales centre thus guaranteeing correct functioning SAFETY The stove must not be used by persons including children with reduced physical sensorial and mental capacities or who are unskilled persons unless they are supervised and trained regarding use of the appliance by a person responsible for their safety Children must be controlled to ensure that they do not play with the appliance Do not touch the stove when you are barefoot or when parts of the body are wet or humid The safety and adjustment devices must not be modified without the authorisation or indications of the manufacturer Do not pull discon
35. o the quantity of pellets adjust pellet feeding directly from the control board The problems correlated to the amount of fuel can be divided into 2 categories NO FUEL the stove can never develop a suitable flame tending to remain very low even at high powers at minimum power the stove tends to almost switch off taking the stove into NO PELLETS alarm conditions when the stove displays the NO PELLETS alarm there may be non burned pellets inside the burn pot EXCESS FUEL the stove develops a very high flame even at low power the panoramic glass is very dirty obscuring it almost totally the burn pot tends to become encrusted blocking the holes for air intake due to the excessive pellet feed as it is only burned partially The regulation to be performed is a percentage Therefore a modification of this parameter will lead to a proportional variation of all stove feeding speeds Feeding is from 30 to 2096 OExtraflame ENGLISH Follow the procedure on the display to perform this adjustment FIRST IGNITION COULD EVEN FAIL AS THE AUGER Press key 7 fora few seconds until SET CLOCK appears ISEMPTY AND IS NOT ALWAYS ABLE TO LOAD Press key 2 several times to reach cur THE BURN POT WITH THE REQUIRED AMOUNT SET USER OF PELLETS ON TIME TO REGULARLY START THE Confirm using key 7 FLAME Pellet is displayed means of the keys 1 and 2 the feeding can be increased 2 or decreased 1 during the WORK
36. ons must be carried out by an authorised technician BLACK OUT NO IGN No current during the ignition phase Take the stove to OFF conditions using key 1 and repeat the procedure described in the Ignition chapter Other restoration operations must be carried out by an authorised technician NO PELLETS In the work phase the t of the flue gases has dropped below factory parameters Check for the presence of pellets in the feed box Regulate the pellet flow Other restoration operations must be carried out by an authorised technician COOLING STAND BY Attempt to release the alarm with stove still in cooling mode Every time the stove displays one of the alarms listed above it will switch off automatically The stove will block any release attempt during this phase showing the alarm itself and ATTE alternately on the display The alarm can be reset by pressing key 1 for 3 seconds only if the fumes motor has stopped and if 15 minutes have passed from displaying the same alarm DEBIMETER FAULT Component disconnected or faulty Contact after sales assistance ENGLISH WARRANTY CONDITIONS EXTRAFLAME S p A with offices in via dell Artigianato 12 Montecchio Precalcino VI guarantees this product for 2 two YEARS from purchase date for manufacturer and material faults The warranty becomes void in case the defect of conformity is not filed with the dealer within two m
37. onths from date of its finding The responsibility of EXTRAFLAME S p A is limited to the supply of the appliance which must be perfectly installed following the indications contained in the appropriate manuals and books provided with the purchased product and in compliance with the laws in force Installation must be performed by qualified staff under the responsibility of the person entrusting him who will assume complete responsibility for the definitive installation and consequent good functioning of the product installed EXTRAFLAME S p A cannot be held responsible for the failure to comply with such precautions WARNING It is essential to carry out the functioning inspection of the product before its completion with the relative masonry finishings counterhood external coating pilasters wall painting etc EXTRAFLAME S p A does not assume any responsibility for any damages and consequent restore expenses of the above finishings even if the same occur following the replacement of malfunctioning particulars THE WARRANTY IS VALIDATED ON THE CONDITION THAT The installation and relative connections of the plant have been carried out by professionally authorised staff in total compliance with the Standard in force M D n 37 dated 22 January 2008 in compliance with the Standards in force both national and regional as well as these instructions Testing has been carried out by a qualified technician who assumes the entire responsibility
38. owing variables TEMPERATURE OF THE FLUE GAS AUGER TIME FLUE GAS SPEED STATUS PASSAGE MINUTES TEMPERATURE OF THE FEED BOX FLOW REAL POWER INLET AIR TEMPERATURE ON MECHANICAL PRESSURE SWITCH It is possible to know the status of the stove at any time Press key 7 for a few seconds until the text SET CLOCK appears Press key 2 several times to reach STOVE STATUS Confirm using key 7 Press key 2 several times to scroll the stove status Menu Press key 6 several times to exit the Menu 46 9999 CHRONO The chrono allows to program 4 time spans within a day to use every day of the week The switch on and switch off time can be set in every time span along with the days of use of the programmed time span and the desired temperature RECOMMENDATIONS Example The ignition and switch off times must be within the arc of one day from 0 to 24 and not over several days Switch on time 07 00 CORRECT Before using the chrono function set the current day and Switch off time 18 00 time Therefore check that the points listed in the Set clock sub chapter have been followed so that the chrono function works Aside from programming it activate it as well Switch on time 22 00 INCORRECT Switch off time 05 00 OExtraflame PROGRAMMING EXAMPLE ENGLISH Let s suppose that the weekly programmer function is to be used and 4 time periods are to be used in the following way 1st time period from 08 00 to 12
39. phase Press key 3 several times to confirm and exit IF THE PROBLEM OCCURS AFTER ONLY A FEW the Menu MONTHS WORKING CHECK THAT ROUTINE CLEANING STATED IN THE STOVE BOOKLET HAS BEEN CARRIED OUT CORRECTLY V1 FAN The menu allows to adjust the speed percentage of the tangential fan FOLLOW THESE INSTRUCTIONS TO PERFORM THE ADJUSTMENT Press key 7 for a few seconds until the text SET CLOCK appears Press key 2 several times to reach SET USER Confirm using key 7 Press key 7 several times to reach V1 FAN By means of the keys 1 and 2 the speed of the tangential fan can be increased 2 or decreased 1 by 10 Press key 3 several times to confirm and exit the Menu STAND BY The Stby function is used if immediate stove switch off is required By activating STAND BY in the standard configuration remote control integated with the room probe when the stove reaches ST the set temperature 2 C settable it switches off to switch back on when it drops 2 C below the set temperature settable 00 lt The STBY function can be set at ON or OFF using the procedure that will be described In the factory the STBY function is always set at OFF Its functioning is compatible with REMOTE CONTROL ROOM PROBE AS PER STANDARD ROOM PROBE OPTIONAL ADDITIONAL THERMOSTAT OPTIONAL FOLLOW THESE INSTRUCTIONS TO ACTIVATE STBY Press key 7 for a few seconds until SET CL
40. ppliance must be able to use the necessary air to guarantee regular functioning through external air inlet The air inlets must comply with the following requisites havea total free section of at least 80 cm must be protected by grates metal net or suitable protections as long as they do not reduce the minimum section stated in the previous point and positioned in order to avoid them being obstructed If the combustion agent air is withdrawn directly from outside through a pipe a downward bend must be mounted outside or a protection against the wind and no grates or similar must be positioned it is recommended that the air vent always communicates directly with the installation room even if the air is withdrawn from outside through a pipe The air flow can also be obtained from an adjacent room as long as the flow takes place freely through permanent openings communicating with the outside The adjacent room with respect to the installation room must not be put in depression with respect to the external environment by means of reverse draught caused by the presence of another used appliance or intake device in such room The permanent openings in the adjacent room must comply with the above described requisites The adjacent room cannot be set up as garage storage for combustion material or activity with danger of fire INSULATION FINISHINGS COVERING AND SAFETY RECOMMENDATIONS The coverings independently from the materials from which
41. rtant as it allows correct recirculation of the air and consequently optimal product functioning THE INSERT MUST LIE AT LEAST 1 CM ABOVE THE SURFACE IN COVERING MARBLE C MAINTENANCE OPERATIONS MUST BE PERFORMED WHEN THE INSERT IS OFF WITH THE PLUG DISCONNECTED FROM THE SOCKET The 2 side frames are fixed to the upper frame by means of 2 screws each side The remaining holes on the side frames allow to fix the entire frame to the sides of the machine by means of self drilling screws PELLETS AND FEEDING The pellets used must comply with the features described by the Standard norm M 7135 DIN plus 51731 UNI CEN TS 14961 Extraflame recommends the use of pellets with a6mm diameter with its products Open the tank lid and load the pellets using a scoop THE USE OF EXPIRED PELLETS OR ANY OTHER MATERIAL DAMAGES THE FUNCTIONS OF YOUR STOVE AND CAN DETERMINE THE INVALIDITY OF THE WARRANTY AND THE ANNEXED RESPONSIBILITY OF THE MANUFACTURER To guarantee combustion without problems the pellets must be kept in a dry place We recommend the use of pellets with diameter of 6mm with our products See the images for feeding pellets Open the tank lid and load the pellets using a scoop In the event of the inserts only load when the machine is off and cold by extracting it from the compartment
42. s original position DExtraflame ENGLISH ROUTINE MAINTENANCE In order to guarantee proper functioning and safety of the device the operations indicated below must be performed every season or more often when necessary DOOR ASH DRAWER AND BURN POT GASKETS The gaskets guarantee the tightness of the stove and its consequent good functioning These must be checked regularly if they should be worn or damaged they must be replaced immediately These operations must be carried out by a qualified technician CONNECTION TO THE FLUE Suck and clean the pipe that leads to the flue yearly or anytime that it is necessary If there are horizontal tracts the residues must be removed before they can obstruct flue passage NON CLEANING JEOPARDISES SAFETY IF THE POWER SUPPLY CABLE IS DAMAGED IT MUST BE REPLACED BY THE AFTER SALES SERVICE OR BY A SIMILARLY QUALIFIED PERSON SO AS TO AVOID AL RISKS A FOR CORRECT FUNCTIONING THE STOVE MUST UNDERGO ROUTINE MAINTENANCE BY A QUALIFIED TECHNICIAN AT LEAST ONCE A YEAR Fumes motor disassembly and cleaning and fumes pipe new silicone in envisioned points Inspection of gaskets and door replace them and apply silicone where required Combustion chamber total cleaning of the entire chamber and cleaning the ignition plug holder tube Feed box complete emptying and cleaning Room air fan disassembly and removal of dust
43. s have passed from displaying the same alarm Fault correlated to the flue gas The restoration operations must be carried out by an FUMES FAILURE exhaust motor authorised technician FUMES PROBE Fault correlated to the fumes probe The o on Osma pe camied out pyan authorised technician Check pellet flow see Pellet feed adjustment ALARM ia Check that the machine is clean including the flue route FUMES OVERTEMPER 54 95 06 Do not rest cloths on the machine ATURE Other restoration operations must be carried out by an authorised technician Thecombustiondiamberor buri sure the burn pot is clean The holes must be completely pot bottom are dirty 1 FLOW ALARM The door or the ash drawer is not Check dooriciosure Check hermetic closure of the ash drawer Cane Check cleanliness of the fumes pipe and the combustion ALL CLEAN CHECK UP The depression sensor is faulty chamber PP The flue exhaust pipe is blocked 6 1 Other restoration operations must be carried out by Incorrect installation authorised technician DEPR ALARM Mechanic depression Sensor Contact after sales centre has tripped The pellet feed box is empty Check for the presence of pellets in the feed box 222100 Adjust pellet flow see Pellet feed adjustment ads bi Check the procedures described in the Ignition chapter IGNITION Incorrect installation 9 pisi Other restoration operati
44. scececsecessnsocsssasassnsossssassssasssssssuescessocansncasencosaneasascasassnsossesassecaeseeses 11 AIR CIRCULATION PIPE 11 COMFORT MIMUCOMPORT MINICRYISTAL an ae 12 COMFORT P80 INSERTIEXTRALTION coreani 13 MOUNTING THE FRAMES osados 14 PELLETS AND FEEDING THE REMOTE CONTROL GENERAL FEATURES ettet CONFIGURATION OF REMOTE CONTROL inneren 16 MENUSTRUCTUUR E ass dada BASIC INSTRUCTIONS COMMISSIONING SETTINGS ADJUSTING TIME DAY MONTH AND YEAR ADJUSTING LANGUAGE FUNCTIONING AND LOGIC ROOM PROBE AND STAND BY FUNCTION STOVE FUNCTIONING WITH ADDITIONAL EXTERNAL THERMOSTAT OPTIONAL scrrccrereseceresioreeseesionioeenrene 20 INSTALLATION AND ACTIVATION OF ROOM PROBE OPTIONAL ussssousossossnssnssnsnnssnsnnsnnsnssnssnnsnsnnsnnsnnsnnsnnsnnnnsnsnnsnnsnne 21 USER MENU 21 ROOM PROBE SOME STAT co TEMA A ERAS OExtraflame ENGLISH WARNINGS The instruction manual is an integral part of the product make sure that it always accompanies the appliance even if transferred to other owners or user or is transferred to another place If it is damaged or lost request another copy from the area technician This product must be destined for the use for which it has been expressly realised The manufacturer is exempt from any liability contractual and extracontractual for injury damage caused t
45. te control To replace them remove the battery holder as indicated in the figure at the back of the remote control remove or insert the battery according to the symbol on the remote control and on the battery itself Two 1 5 V AA batteries are required for operation Dimensions 61 x 150 x 120 B x Hx P mm The batteries used contain metals harmful for the environment They must therefore be disposed of separately in appropriate containers SOME RADIO FREQUENCY APPLIANCES E G MOBILE PHONES ETC COULD INTERRUPT THE COMMUNICATION BETWEEN THE REMOTE CONTROL AND THE STOVE OExtraflame MENU STRUCTURE amp SETCLOCK Ke H DAY D ENABLE CHRONO HOURS SET CHRONO EC 1 Y Y IT EN FR DE ES CONFIRM START PROG1 MINUTES LANGUAGE ids ni Y e Y USER H7 PELLET STOP PROG 1 DATE ow oz STOVE STATUS FAN V1 MONDAY SUNDAY 11252 522 5 TECHNIC SET STAND BY SET PRG1 YEAR 122 1 2 3 y y KEYS LOCKED REPEAT THE SAME PASSAGES FOR 1152 THE OTHER 3 TIME PERIODS Y REMOTE CONTROL PROBE 152 Y RESET The following recommendations must be followed the first times the stove is ignited Itis possible that slight odours are produced due to the drying of the paints and silicones used Do not remain in the environment for long periods Donottouch the surfaces as they could still be
46. tivated by electric motor NATURAL DRAUGHT Draught which is determined in a chimney flue for effect of the volume mass difference existing between smoke hot and surrounding atmosphere air without any mechanical intake aid installed inside it or at its peak OExtraflame ENGLISH RADIATION AREA Area immediately near the hearth in which the heat caused by combustion is diffused where no combustion materials must be present REFLUX AREA Area where leaking of the combustion products is verified from the appliance towards the installation room The installation must be preceded by checking the chimneys flues or unload terminals positioning of appliances similarly to Installation prohibitions Legal distances Limitations disposed by local administrative regulations or particular authority prescriptions Conventional limitations deriving from condominium regulations constraints or contracts INSTALLATIONS ALLOWED Only appliances working in a sealed manner respect to the room or which do not place the room in depression respect to the external environment can exist or be installed in the room where the heat generator will be installed Appliances for cooking food and relative hoods without extractor are only allowed in kitchens INSTALLATIONS NOT ALLOWED In the room where the heat generator will be installed the following must not pre exist or be installed hoods with extractor collective type ventilatio
47. ton 5 access 1 and 2 adjustment Power 1 minimum level Power 5 maximum level WORKING WITH REMOTE CONTROL ROOM PROBE AS PER STANDARD The appliance controls room temperature by means of the room probe integrated in the remote control Having reached the set temperature it will automatically go to the minimum or switch off activating the Stand by function reducing pellet consumption to a minimum In the factory the STBY function is always set at OFF STBY indicator light off For its activation and logic follow the indications on the following page chapter Room probe and Stand by function BURN POT CLEANING While working the stove has an internal counter which cleans the burn pot after a set amount of time This phase will be shown on the display it will bring the stove to a lower power level and will increase the flue gas motor for a programmed amount of time When the cleaning phase is finished the stove will continue work going back to the selected power level SWITCH OFF Press key 1 for three seconds When the operation has been performed the appliance automatically enters the switch off phase blocking the supply of pellets The flue exhaust motor and the hot air ventilation motor will remain on until the temperature of the stove has dropped below the factory parameters RE IGNITION The stove can only be re ignited if the flue gas temperature has lowered and the preset timer has been reset to zero OExtra
48. unstable room well several times The hardening of the surfaces is terminated after several heating processes This appliance must not be used to burn waste gt IT ISFORBIDDEN TO USE THE APPLIANCE WITHOUT THE DIVIDER AND OR GLASS PROTECTION SEE FIGURE AT THE SITE JEOPARDISES THE SAFETY OF THE PRODUCT AND LEADS TO THE IMMEDIATE VOIDING OF THE WARRANTY PERIOD IN THE CASE OF WEAR OR DETERIORATION REQUEST AFTER SALES ASSISTANCE FOR REPLACEMENT OF THE PART REPLACEMENT THAT ISNOT UNDER GUARANTEE AS THE COMPONENT IS SUBJECT TO WEAR 9 make sure the power supply cable is connected correctly the bipolar switch in the rear right part must be KEYS1 amp 2 to set enable data and parameters ENGLISH KEY 3 to confirm parameter and exit KEY 4 to adjust thermostat setting KEY 5 to adjust power setting KEY 6 to go back in menu KEY 7 to go forward in menu Before igniting the stove the following points must be verified the feed box must be full of pellets the combustion chamber must be clean The burn pot must be completely free and clean check the hermetic closure of the fire door and the ash rawer positioned on 1 DIVIDER N GLASS PROTECTION DExtraflame ENGLISH COMMISSIONING SETTINGS Once the power cable at the back of the stove has been connected move the swit
Download Pdf Manuals
Related Search