KIP 700m - User Manual - KIP
Contents
1. n II a M EE ua TR n KIP 700m User Manual Version A1 Thank you for purchasing the Multi Function Printer KIP 700m This Hardware Operation Guide contains functional and operational explanations for the KIP 700m Please read this Hardware Operation Guide carefully before using the printer Please keep this Hardware Operation Guide for future reference 1 When this product is installed in North America This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 When this product is installed in Europe This equipment complies with the requirements in Pub 22 of CISPR Rules for a Class B computing device Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference Do not install Machine around other electronic equipment or other precision instruments Other devices may be effected by electrical noise during operation If the Machine is installed near other electronic equipment such as a TV or a radio interference to said equipment such as noise or flickering may occur Use a separate power line and install the PRINTER as far as possible from said equipment A2. 10 2 inch core plain paper media support 1 4 Chapter 1 Before Use 1 4 Specifications 1 4 1 General oubject Specification KIP 700m Console with the stand Maximum Low power mode Acoustic noise impulse sound excluded EN ISO 7779 Max 0 05ppm Measurement method under UL Standard 1245mm Width x 680mm Depth x 611mm Height Stand excluded About 144kg 318lbs Stand excluded Environmental condition Temperature 10 to 32 degrees Centigrade 50 to 89 6 F for usage Humidity 15 to 8596 RH Network Interface 10 BASE T 100 BASE TX 100BASE T Rating input power In the US 120V plus minus 10 50 60Hz 15A In Europe 220 240V plus 6 or minus 10 50 60Hz 10A A NOTE The above specifications are subject to change without notice 1 5 Chapter 1 Before Use 1 4 2 Printer part Subject Printing method Photoreceptor Organic Photoconductive Drum 40mm per second Print speed 1 7bppm E 3 ppm D Landscape Print head LED Array Resolution of print head 600dpi x 600dpi Print width Maximum 914mm 36 Minimum 297mm 11 for roll media 210mm 8 5 for cut sheet Maximum Standard Print length 2 400mm for AO 36 wide plain paper bond or 2 x Standard length plain paper bond 1 x Standard length plain paper bond 2 core roll Option Minimum 297mm 11 A NOTE If the print is longer than 2 400mm its image quality or the reli
3. 1 8 1 5 Appearance pi wa n de ies ere SENET LORS Ee uni n CN qu Mu E Ld ctu LU ir 1 9 1 5 1 Front view mene 1 9 1 5 2 Rear view menn 1 10 1 6 Specifications for the Scan Original a CA Nada coa Dp Rae Aa aa T DEM MI D ad 1 1 1 1 7 Specifications for the Printing Paper M cunc pop MALO EN A LUE a M ADT 1 14 1 7 1 Papers notavallable to ISO ss seas re teniendo Stet ees emit bree iain dnd tarte 1 14 1 7 2 Keeping the paper in the custody Q Mo e 1 15 1 7 3 Treatment against environmental condilion eee uet 1 16 1 1 Chapter 1 Before Use 1 1 Installation Requirements The following conditions are required for installation of the equipment Q 1 POWER SOURCE should be rated as follows In U S A 120V plus minus 10 50 60Hz 15A or higher In Europe 220 240V plus 6 or minus10 50 60Hz 10A or higher 2 The equipment must be on an exclusive circuit 3 The outlet must be near the equipment and easily accessible 1 Make sure to connect this equipment to a grounded outlet 2 For PLUGGABLE EQUIPMENT the socket outlet shall be installed near the equipment and shall be easily accessible The site temperature range 10 to 32 degrees Centigrade with the humidity between 15 to 85 RH NON CONDENSING Keep the printer away from water sources boilers humidifiers or refrigerators 1 The installation site must not have open flames dust or ammonia gases 2 The equipment must not be expose
4. 1 2 J 02053 Manual Feeder sector ete ee Rene du ae 3 4 3 1 3 J 0104 0204 Media Feed section shee etti 3 5 3 1 4 J 01057 0205 Media Feed section 2 eee teet 2 7 3 1 5 0106 0206 tT T rla 3 9 3 1 6 J 1300 1400 Door Open while printing RAR ARRASAR 3 12 3 1 7 Original ausente as 3 14 3 2 Other Operator Call Error T cq m Tt 3s 5 3 2 1 Roll Replacement Cd E EE au EE d cM dU ud E E A i cM otio es 3 15 3 2 2 Toner Empty Ks ho a a 3 45 3 2 3 Roll Deck Cover Open a E ee esas ERE Te ee EIN TTT ran AD Lu eR Ete ran aC eee QU Dad 3 15 3 2 4 Scanner Open hit uu eS EEE eT PRE EE RI cC LEA MM M t RIR 3 15 3 2 5 Printer NO Avallablg ssceesatese tette ttt rapto eee ee ra cee eect 3 15 2 5 GCamice Call Eror docebat RS rete ctus teens aca ee 3 16 3 1 Chapter 3 Error Correction 3 1 Mis feed Error If a jam occurs the Ul screen will show its location and the corresponding code J if any Please refer to the following figure to check the jam location Mis feed Codes are described on the later pages Fuser Section J 0106 0206 Feed Section 2 J 0105 0205 Manual Feeder Section J 0203 a N a RN Feed Section 1 fo Roll Deck Section J 0103 A NOTE 1 Be careful not to get paper cuts on your hand 2 It is recommended to take off your ring bracelet or watch when removing a mis feed media 3 2 Chapter 3 Error Correction 3 1 1 J 0103 Roll Deck
5. section Hemove a mis feed media in the Roll Deck if the Ul screen will show J 0103 E O x 1 Open the Roll Deck Cover Hewind the roll onto the media core 2 If the leading edge of the media has a torn fold trim the edge cut it off with Initial Cut function 3 Close the Roll Deck Cover Reference If your roll media s end is not fixed to the core by glue or a tape a small portion of the media may remain in the media path of the Roll Deck at a roll empty The printer does not show any mis feed error code against the portion So please check for the portion in the media path through the square window 1 in the middle of the Roll Deck If you can see a portion rotate the green roller 2 on the right to the arrow direction to remove it a Ue A Mo i D LC 3 3 Chapter 3 Error Correction 3 1 2 J 0203 Manul Feeder section Remove a mis feed media in the Manual Feeder if the UI screen will show J 0203 J 0203 1 Pull out the mis feed cut sheet from the Manual Feeder The mis feed cut sheet should be replaced with a new one if its leading edge has a torn or fold Or it should be used upside down to keep the damaged edge from been inserted An extremely creased cut sheet may cause mis feed again 3 4 Chapter 3 Error Correction 3 1 3 J 01 04 0 20 4 M edia Fe ed er Sec tio n 1 He m ove a ii is f eed m a 1 In the M aF eed er section 1 if
6. th eU ls cre en sho W J 01 04 or O 20 4 gi 3 KS Ch a pter 3 Error Co rrec om 3 Put your hands on the rear rim of the scanner unit just as you hold the Upper Unit Push the entire unit down to the arrow direction Hold here 3 6 Chapter 3 Error Correction 3 1 4 J 0105 0205 Media Feeder section 2 Remove a mis feed media in the Media Feeder section 2 if the Ul screen will show J 0105 or 0205 J 0105 or J 0205 05 or J 0205 3 e 2 Remove the mis feed media 3 7 Chapter 3 Error Correction 3 Put your hands on the rear rim of the scanner unit just as you hold the Upper Unit Push the entire unit down to the arrow direction Hold here 3 8 Chapter 3 Error Correction 3 1 4 J 0106 0206 Fuser section Remove a mis feed media in the Fuser section if the Ul screen will show J 0106 or 0206 J 0106 or J 0206 c CS ES B ENO 1 Hold the blue handle 1 and open the Exit Cover 2 If it is possible pull and remove the mis feed media If little amount of the leading edge area is coming to the Fuser and you cannot pull it out or if the trailing edge remains deep to be caught in the printer do not pull it by force Leave it there and go to the next step A WARNING There are extremely hot parts inside the Fuser Unit Do not touch any parts in the Fuser Unit or you will be burnt Also the mis fed media can be very hot Be careful not to get burnt
7. the table of Bypass Feeder which indicate possible feed positions Place the cut sheet on the table between its concerning size markings then insert it into the Bypass Feeder When the leading edge touches the feeding roller the printer automatically carries and sets the paper at the proper position size marking 1 As a curly cut sheet will cause a mis feed straighten the sheet as far as possible before printing And set the sheet in curl down direction as a mis feed can be avoided Curl up sheets tend to result in a mis feed Correct curl down Wrong curl up 2 Setting a cut sheet to the Bypass Feeder while the printer is processing a print job cause a paper jam 2 13 Chapter 2 Basic Operation 2 Copying 1 There are several size markings on Original Table which indicate possible feed positions Line up Original Guides 1 with the proper markings according to the original width 2 Place the original on the Original Table with face up Then insert it under the Scanner Unit along with Original Guides When the leading edge touches the original feeding roller the machine automatically carries and sets the original at the proper position 3 The KIP 700m will start the copy process The scanner unit does not accept originals automatically during Sleep Mode Tap on the UI screen and then insert an original 2 14 Chapter 2 Basic Operation 2 8 Emergency Stop of Scan or Copy 1 If necessary press t
8. 11 Chapter 1 Before Use Not square KIP KIP Wet Metal or fabric material Metal Fabric Rough surface Carbon paper for example Rough surface Clipped or stapled Clipped Stapled i 1 12 Chapter 1 Before Use The following kinds of originals can be read with using a carrier sheet Image quality or the reliability of paper feeding for them is not guaranteed Patched Punched 1 13 Chapter 1 Before Use 1 7 Specifications for the Printing Paper 1 7 1 Papers not available to use Do not use the following kinds of printing paper Doing so may damage the print engine Excessively curled a diameter of 50 mm or less Folded 1 14 Chapter 1 Before Use E NN SS Os Eos IS A CAUTION Do not use the paper with staple or do not use such conductive paper as aluminum foil and carbon paper The above may result in a danger of fire A NOTE 1 Print image may become light if printed on a rough surface of the paper 2 Print image may become defectiv
9. B port Your USB flash memory storage can be installed here 5VDC max Read the original with this unit when you make scan or copy B 1 9 Chapter 1 Before Use 1 5 2 Rear view LI z T d mM 1 TC RR Ras SER CU m s Th B E iB x xn Y E i EMI E S i 8 a d EE I i i B Ir i 200040 l Sey I LE gt ta reais os ow NE i i l B XP RE a k f BEBNENI T PM LE ger E IESE E z q EH IBEI B B n P Tr C 0 t i N TITL Ls quit L No Name Function Toner Cover Open here to access toner supply system Original Guide These trays catch the original ejected from the Scanner Unit 3 LAN Port Conneci the LAN Cable to connect the KIP 700m to the network Do not connect a telephone line Service Use 5VDC max It is possible to shut off supplying the AC power E E D D D D 6 Inlet Socket Connect the Power Cord here 1 10 Chapter 1 Before Use 1 6 Specifications for the Scan Original A scan original must satisfy the following specifications 0 05mm to 1 6mm Width 2 9 4mm to 914 4mm Length 210mm to 6 000mm If an original is thicker than 0 65mm its image quality is not guaranteed even it is transported Do not scan the following kinds of originals The original or the scanner may damage Sticked with paste Folded Leading edge Excessively curled a diameter of 50 mm or less 1
10. Basic Operation page T rning on ae tabe tici tehtes opulenti Qu ol dttu ubi D SO Turnind off KIP 700 ceteri edi ee ee 2 4 Replacing Roll Media azasaat Eae 2 5 initial CUL oec oett adden epa MED Eee Er A at Id dede 2 9 Toner SUDDIV esc rein renee 2 10 CutShesi Media ratia a E a pa 2 13 Copying ee a ee 9 14 Emergency Stop of Scan or Copy 2 16 Canceling Sleep Mode emt eee 9 17 2 1 Chapter 2 Basic Operation 2 1 Turning on KIP 700m 1 Ensure that the KIP 700m is plugged into a dedicated wall outlet A WARNING 1 Do not handle the Power Plug with wet hands or you may receive an electrical shock 2 Make sure to earth the machine for safety 3 Do not plug the printer into a multi wiring connector in which other devices are plugged It may overheat the outlet and may result in a fire 4 The OUTLET must satisfy the following conditions In the U S A 120V plus minus 1096 50 60Hz and 15A In Europe 220 240V plus 6 or minus 10 50 60Hz and 10A 2 Press side the Power Switch on the right side of the printer to turn on the KIP 700m o Power Switch Press side 2 2 Chapter 2 Basic Operation 3 The User Interface UI starts operating and displays the following Copy Mode Screen in one minute The Ready Indicator on Copy Mode Screen will flash during warming up mim me PRINT QUEUE FILE TO PRINT Roll 1 914mm Bond The Ul screen may vary depending on your system
11. ability of paper feeding is not guaranteed Print size from Paper Tray option Length 220 297 210 EFE ao x rer x x ANSI inch Shorter than 2 minutes 30 seconds At 23 C 60 RH the rated voltage and plain paper is used 43 seconds D Landscape At 23 C 60 RH the rated voltage and plain paper is used Fusing method Heat and Pressure Rollers Develooment method Dry tyoe non magnetic mono component toner A NOTE The above specifications are subject to change without notice 1 6 Chapter 1 Before Use Media source 1 Roll Deck 3 2 core roll Manual Feeder single cut sheet Paper Tray multiple cut sheet option Media Recommended Roll Media US model Bond 64g m to 80g m US Bond PB 20 Vellum US Vellum XV 20 Film 4MIL PF 4DDME Europe Asia model Plain Paper 64g m to 80g m Oce Red Label 75g m Tracing Paper Transparent Paper 80g m Film 3 5MIL 2 roll core Universal Bond Cut sheet Plain Paper Bond Storage of consumables Toner cartridge Store the cartridge within the temperature range from 0 to 40 degrees Centigrade and within the humidity range from 10 to 85 RH A NOTE The above specifications are subject to change without notice 1 7 Chapter 1 Before Use 1 4 3 Scanner part Specification Scanning method Contact Image Sensor CIS 5 pieces of A4 sized CIS LED R G B Setting of original Starting point of scan Sca
12. als as book music paintings printed copy maps drawings movie and pictures which are protected by the copyright except for personnel or family use or similar purpose 1 3 Chapter 1 Before Use 1 3 Features 1 KIP 700m is a Multi Function Printer for scan copy and print large format documents Some of these features may be optional 2 Front loading front delivery structure saves the installation space 3 Various media source roll media feeding 1 roll cut sheet manual feeding Paper Tray multiple cut sheet feeder option 4 A dedicated printer stand option offers easy print handling with the print basket The KIP 00m is also suitable for your office layout as a desktop MFP 5 The operation speed is 40mm s 3 D landscape per minute 6 The maximum print width is 914mm 36 wide and the minimum one is 210mm or 8 5 The maximum print length is 2 400mm for AO 36 wide media and the minimum one is 29 mm or 11 7 Up to 600dpi print resolutions with an enhanced scanning system produces the highest quality images controlled by an advanced KIP Image Process System 8 The combination of KIP Contact Development System and mono component minute toner can produce a high definition line distinctive grayscale and consistent solid black The KIP HDP process generates no Waste Toner 9 Easy access to USB port allows users to provide efficient productivity by using File to Print Scan to USB option
13. blic of China Safety Warnings The following warnings are very important in order to safely use this product These notes are important in preventing danger to the operator or operation of the printer The following symbols are found throughout the USER S Manual and have the following meaning WARNING This WARNING mark means that there is a possibility of death or serious injury if you ignore or do not follow the said instruction CAUTION This CAUTION mark means that there is a possibility of injury or physical damage if you ignore or do not follow the said instruction When marked with this symbol DO NOT ATTEMPT When marked with this symbol pay close attention to WARNING Ground the product with a correct ground source or you may be electrically shocked The Power source should be as follows In U S A 120V plus minus10 50 60Hz 15A or higher In Europe 220 240V plus6 or minus10 50 60Hz 10A or higher Use a circuit with a dedicated breaker Install the product as close to the wall outlet as possible If you wish to move the printer please contact your service personnel Do not remove the screw and do not open the cover if not instructed to do so in this User s Manual If you ignore this warning you may be burnt or receive an electric shock due to a hot item or electrically charged part inside of the printer Do not disassemble or tamper with the printer It may result in a fire or an
14. configuration Shown with available options 4 When Ready Indicator stops flashing the KIP 700m is ready for operation A NOTE It is impossible to make any prints while Ready Indicator is U U U P P t Wi Uu flashing in orange Please wait until it turns in green Q MUNERE D 2 3 Chapter 2 Basic Operation 2 2 Turning off KIP 700m 1 There is a Power Switch on the right side of KIP 700m Press its side to turn off the KIP 700m o Power Switch Press side CAUTION The KIP 700m print engine and Ul appear to be shut down when you turn off KIP 700m However the controller PC embedded inside the KIP 700m is still operating and will shutdown in approximately two minutes after Power Switch operation Do not unplug the KIP 700m before the controller PC completes its shutdown Doing so may damage data or the device 2 4 Chapter 2 Basic Operation 2 3 Replacing Roll Media A NOTE A media mis feed tends to occur just before out of a roll media 1 Open Roll Deck Cover 1 Holding both Flanges 2 lift and remove a roll media or an empty roll core 3 3 Move the right Slide Guide 5 to match your roll media s width The right and left Slide Guides move together Nr SP Ar right left Slide Guide move together 2 5 Chapter 2 Basic Operation 4 Insert each Flange 2 into both ends of the roll media core to be installed A NOTE 1 Fully insert Flan
15. d to the air vents from air conditioners It may affect the image quality 3 The equipment should not be exposed to the direct sunlight Please draw curtains to block any sunlight When you open the Movable Unit do not expose the Photoconductive Drum to strong intense light as this will damage the Drum is within safe levels see certifications Q Ozone will be generated while this equipment is use although the quantity generated Ventilate the room if required Keep ample room around the equipment to ensure comfortable operation Refer to the following figure The equipment must be leveled and the floor strength must be ample to sustain the weight of the equipment 20cm 8 or larger with no option UNT 7 _ KIP 700m 10cm 4 or larger 10cm 4 or larger 1 1 2 Chapter 1 Before Use 1 2 Originals Prohibited from Duplication It is not necessarily allowed to copy every kind of original You may be punished by the law if only you possess the copy of some kind of original We recommend you to consider enough before you copy such original Originals prohibited from copying by the law 1 It is not allowed to copy Currency Bill Money Bank Note etc Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc 2 It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments 3 It is not allowed to copy unused postal stamps or government postcards without p
16. e if the print paper has an excess curl 3 It will cause paper mis fed poor print image or creasing if you use a paper that does not satisfy the specifications 4 Do not use a paper of which surface is very special such as thermal paper art paper aluminum foil carbon paper or conductive paper 5 Vellum exposed to air over a long period tends to cause a defective printing It is recommended to remove one round on the surface of the vellum roll from the beginning 6 Remove fully any adhesive from the roll that may remain due to tape placed by the media supplier 7 Do not use papers with unpacked exposed in high low temperature amp humidity in a long period Such papers may result in mis feed defective image or paper creasing 8 It is recommended to trim the leading edge by using Initial Cut Key on the User Interface Ul before making a long print For trimming the leading edge see 2 4 Initial Cut 1 7 2 Keeping the paper in the custody Keep the paper in the custody taking care of the following matters Do not expose the paper to the direct sunlight Keep the paper away from high humidity It must be less than 70 Put the paper on a flat place If you will keep the paper in the custody which you have already unpacked put it into the polyethylene bag to avoid the humidity Do II 1 15 Chapter 1 Before Use 1 7 3 Treatment against environmental condition Take a necessary treatment according to the envi
17. electrical shock Do not plug in the printer into a multi wire connector in which some other equipment is plugged into It may cause a fire due to outlet overheating Do not damage the Power Cord by stepping on or placing heavy items on it If the Power Cord is damaged it may cause a fire or you may receive an electric shock REPLACE THE CORD IF DAMAGED Do not put a flower vase a flowerpot or any water filled item on the product Spilt water could cause a fire or an electric shock If the product generates an abnormal smell or noise turn it off and unplug it from the wall electrical outlet immediately Do not throw the toner into a fire or other sources of heat as it can explode CAUTION Do not install the printer in a humidified room or a dusty room Also do not install the printer on an unstable floor as injuries may occur 1 Unplug the printer before you move it The power cord may be damaged and it may result in a fire or electric shock If you do not use the printer for a long duration holidays company shutdown turn off and unplug the printer from the outlet for safety Do not pull the cord when you unplug the printer as you may damage the Power Cord There are hot items inside of the printer Take great care not to touch these items when you remove mis fed media Ventilate the room well if you print in a small area POWER CORD INSTRUCTION The installation of or exchange to a power plug
18. ermission to make replica from Government 4 It is not allowed to copy Government issued revenue stamps certificate stamps which are prescribed by Liquor Tax Act or the Commodity Tax Act Special items to be cared 1 Itis warned by the government to copy private issued securities stock certificate draft check goods ticket etc commutation ticket or book of tickets excluding that some specific company copies such originals as many as it requires for its own business 2 We recommend you not to copy freely such originals as government issued passport public or private issued licenses automobile inspection certification IDs and tickets like pass or meal Prohibited items to copy Regulations to control fake currency and Currency Bill Money Bank Note etc Bond Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc Control Law against Forged amp faked Foreign Currency or Foreign Negotiable Foreign Currency Bill Bank Note and Bond Instruments Forged postal stamps control law Unused postal stamps or government postcards Forged revenue stamps control law Government issued revenue stamps and certificate stamps prescribed by Liquor Tax Act or Commodity Tax Act Currency similarity securities Control Law Private issued securities stock draft check goods ticket etc commutation or book tickets Originals protected by the copyright It is prohibited to copy such origin
19. ge into the roll media core so that the inside rim of Flange evenly touches the side face of the roll media Correct Fully inserted Wrong not touching roll side 2 Flange has Stoppers with sharp edge Be sure not to touch them 5 Push the green lever 4 down in either way Position them flat against Flange to secure the roll media 2 6 Chapter 2 Basic Operation 6 Lift the roll media by holding both Flanges Lower Flanges onto Slide Guides 5 in Roll Deck 1 Be careful of the winding direction of the roll media This direction 2 The outside rim of Flange 2 should fit into the groove on the Slide Guide Otherwise the roll media may fall in Roll Deck or result in an incorrect media feeding L groove groove 2 7 Chapter 2 Basic Operation 7 Rotate the roll media in the arrow direction and insert the leading edge of the roll media to the media path until it touches the feeding rollers 6 After that the leading edge will automatically go into the roll media s wait position This is called Auto Media Loading 22998 Reference Auto Media Loading becomes available while the printer is ready 8 Trim the leading edge of the roll media with Initial Cut function if necessary For Initial Cut see the next page on 2 4 Initial Cut 2 8 Chapter 2 Basic Operation 2 4 Initial Cut Reference 1 Initial Cut is a function to trim the roll media with its leading edge cut off 2 In
20. he Emergency Stop Button 1 on the Scanner Unit to immediately stop the original while making a copy or scan Pressing the button stops the current reading a document immediately The current printing is stopped as well and is ejected A NOTE Do not pull back or hold down the original on Original Table as an attempt to stop feeding it through Scanner Unit 2 15 Chapter 2 Basic Operation 2 9 Canceling Sleep Mode The KIP 700m has two Sleep Modes to reduce the power consumption The KIP 700m will enter Sleep Mode after a certain period of inactivity In the default setting e Warm Sleep Mode will start after a 15 minute of inactivity in order to reduce the power supply for Fuser Unit e Cold Sleep Mode will start after a 60 minute of inactivity to stop the power supply for Fuser Unit and some other components Sleep Mode is canceled and the machine gets ready when e the machine receives a print job through the network e you tap on the UI screen then an original is inserted the scanner unit A NOTE 1 It may take time for the machine to get ready 2 Tapping on the Ul screen can cancel the screensaver but the KIP 700m needs to recover temperature on Fuser Unit It may need another waiting time to start warming up for printing 2 16 Chapter 2 Basic Operation Chapter 3 Error Correction page 3 1 Misfead Error ero E ee 3 2 3 1 1 Js0103 Roll Deck Sector sedet oa i ON EP a e ada e aad boe ada aet 2 2 3
21. itial Cut becomes available while the printer is ready 1 Open the Manual Feeder Table 1 3 The leading edge of the roll media is automatically transported and cut off Remove the portion of the media 3 and close the Manual Feeder Table 1 2 9 Chapter 2 Basic Operation 2 5 Toner Supply 1 Open the Toner Hatch 1 on the rear top You do not have to remove the Original Guide 2 Shake the Toner Bottle 2 several times to loosen the toner AA NOTE After you shake the Toner Bottle well proceed the later step 3 and 4 as soon as possible Having a pause after step 2 may reduce smoothness of the toner This would disturb a smooth toner supply from the Toner Bottle to the printer 2 10 Chapter 2 Basic Operation 3 Put the dent area 3 under the holder 4 to firmly seat the bottom plate of the Toner Bottle 2 to the toner supply position 2 11 Chapter 2 Basic Operation 4 With pressing down the Toner Bottle 2 slide the green lever 5 to the arrow direction until it stops When it stops wait 10 seconds as it is H i i from right NOTE It is impossible to remove the Toner Bottle unless the lever 5 completely moves to the Original position Do not attempt to remove the Toner Bottle by force if the lever is not at the original position Doing so may damage toner supply system 2 12 Chapter 2 Basic Operation 2 6 Cut Sheet Media There are several size markings on
22. media core 6 If the leading edge of the media has a torn fold trim the edge cut it off with Initial Cut function 7 Close the Roll Deck Cover 3 13 Chapter 3 Error Correction 3 1 7 Original Jam If an original is mis fed while scanning the Ul screen shows Original Jam Follow the instruction below to remove the mis fed original 1 On both sides pull the levers 1 under the scanner cover to open the Scanner Unit until it locks 2 Remove a mis feed original 3 Gently press the Scanner Unit down and firmly close it NOTE Press down the Scanner Unit on both sides to close it Do not close it by pressing only one side down 3 14 Chapter 3 Error Correction 3 2 Other Operator Call Error When the printer is running out of a loaded roll media the UI Screen will display Roll Replacement sign If there is no suitable roll media required for the current print job the Ul Screen will display Roll Replacement sign as well Please load the required roll media to any Roll Deck For the roll replacement procedure see 2 3 Replacing Roll Media 3 2 1 Roll Replacement v 3 2 2 Toner Empty kez When the printer is running out of toner the UI Screen will display Toner Empty sign For the toner supply procedure see 2 5 Toner Supply 3 2 3 Roll Deck Cover Open If the Roll Deck Cover is open not closed properly the UI screen shows Roll Deck Cover Open Gently cl
23. n width Max 914 4mm 36 Scan length Max 6 000mm 19 7ft Including the margin area Min 210mm 8 5 Including the margin area Digital resolution 200 300 400 600 dpi Original transportation Sheet through type Transportable original Max 1 60mm thickness Min 0 05mm A NOTE If the original is thicker than 0 65mm its image quality is not guaranteed 60mm per second max A NOTE The above specifications are subject to change without notice 1 8 Chapter 1 Before Use 1 5 Appearance 1 5 1 Front view Function Main Switch You can turn on off the KIP 700m Original Guides Feed the original under the Scanner Unit along the Original Guides 3 User Interface This is a Touch Screen and many kinds of user operation are available PLEASE DO NOT push the LCD area too strong 4 Emergent Stop Button Press this red button when you would like to stop copying or scanning emergently Original Table Place the original here and then feed it into the Scanner Unit when you make scan or copy Ly 7 Engine Unit Open Lever Push down these blue levers when you open the Engine Unit Feed a cut sheet paper from the Bypass Feeder 8 Roll Deck Cover Lift up to open the Roll Deck ME A roll media can be loaded in the Roll Deck Consult your sales dealer for optional media feed system Use this to press buttons on the touch screen PLEASE DO NOT use any other pointed object to tap on the UI 13 US
24. ose the Roll Deck Cover 3 2 4 Scanner Unit Open The UI screen shows Scanner Unit Open if the Scanner Unit is open not closed properly For closing the Scanner Unit see 3 1 7 Original Jam 3 2 5 Printer Not Available If the Exit Cover or the Upper Unit is open not closed properly the Ul screen shows Printer Not Available Please check that either Exit Cover or Upper Unit is firmly closed If it seems no problem turn off and again on the machine s power switch 3 15 Chapter 3 Error Correction 3 3 Service Call Error In case the following Error Codes for a serious failure appear in the screen PLEASE CALL YOUR TRAINED SERVICE PERSONNEL TO RESOLVE THE ERRORS No operation should be done by the customer If any of the above errors appear 1 Turn off KIP 700m and turn it on after an interval of 30 seconds or more 2 If the same error code appears turn off KIP 700m and then unplug the printer from the wall outlet after an interval of two minutes for shutdown Call your service personnel 3 16 Chapter 3 Error Correction Chapter 4 Maintenance page leaning cT EPI t cM a AE RT 4 2 Scanner Unit rm ANTA METER ET 4 2 Touch Screen n 4 4 4 1 Chapter 4 Maintenance 4 1 Cleaning 4 1 1 Scanner Unit It is recommended to clean each Scan Glass Feeding Rollers and Guide Plates as the scan copy image may become defective if these parts are dirty 1 Turn off KIP 700m 2 Press the levers 1 up to
25. ronmental condition as shown below Humidity Possible problem Necessary treatment Void of image crease of paper and 1 Install an humidifier in the room and other problems occurs when you print humidify the room air with plain paper and tracing paper 2 Remove the paper from the machine right after the completion of print and keep it in a polyethylene bag Void of image occurs when you print If you will not make print soon remove with tracing paper the tracing paper from the machine and keep it in a polyethylene bag Hemove the paper from the machine after everyday use and keep it in a polyethylene bag Void of image occurs when you print If you will not make print soon remove with plain paper and tracing paper the tracing paper from the machine and keep it in a polyethylene bag Void of image crease of paper and 1 Use a dehumidifier or such equipment other problems occurs when you print 2 Remove the paper from the machine with plain paper and tracing paper right after the completion of print and keep it in a polyethylene bag A NOTE 1 Using a dehumidifier in high humidity environment 6596 or higher is recommended 2 Void of image and crease of paper will occur in case of extremely high or low humidity Normal Print Crease of paper If the media is humidified If the media is humidified 1 16 Chapter 1 Before Use Chapter 2
26. s an ENERGY STAR O Partner Katsuragawa Electric Co Ltd has determined Es that this product meets the ENERGY STAR O guidelines for energy efficiency 7d ENERGY STAR The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment The program backs the development and dissemination of products with functions that effectively reduce energy consumption It is an open system in which business proprietors can participate voluntarily The targeted products are office equipment such as computers monitors printers facsimiles copiers scanners and multifunction devices Their standards and logos are uniform among participating nations 2002 96 EC of the European Parliament and the council of 27 January 2003 on waste electrical and electronic equipment WEEE and does not apply to countries outside of EU E The symbol shown indicates that this product conforms to Directive 9 Only For EU Member States The symbol shown indicates that this product conforms to Industry Standard and does not apply to countries outside of People s Republic of China SJ T11364 2006 of People s Republic of China Electronic es Dn The symbol shown indicates that this product conforms to GB 18455 2001 11364 2006 of National Standard of the People s Republic of China and does not apply to countries outside of People s Repu
27. unlock the Scanner Unit Open the Scanner Unit 3 Wipe each Scan Glass 2 Pinch Rollers 3 gray and the inside surface of the metal plates with a soft cloth Use equal volume mixture of water and a neutral detergent A NOTE Do not use organic solvent glass cleaner and anti static spray for the cleaning 4 2 Chapter 4 Maintenance 4 Wipe the Feed Rollers 4 gray Press Rollers 5 white and the inside surface with a soft dry cloth Press down Scanner Unit on both side to close it Do not close it by pressing only one side down 4 3 Chapter 4 Maintenance 4 1 2 Touch Screen 1 Wipe the Touch Screen with a dry cloth A NOTE Do not use water alcohol organic solvent and glass cleaner for the cleaning 4 4 Chapter 4 Maintenance
28. when you remove it 3 9 Chapter 3 Error Correction 2 Close the Exit Cover 1 3 Press down the blue levers 3 on both sides to unlock and open the Upper Unit 4 Remove the mis feed media 3 10 Chapter 3 Error Correction 5 Put your hands on the rear rim of the scanner unit just as you hold the Upper Unit Push the entire unit down to the arrow direction Hold here 3 11 Chapter 3 Error Correction 3 1 6 J 1300 1400 Door Open while printing If the Exit Cover or the Upper Unit is open while the printer is processing a print job the Ul screen will show J 1300 Exit Cover J 1400 Upper Unit For clearing J 1400 please start on the step 3 1 Open the Exit Cover If little amount of the leading edge area is coming to the Fuser and you cannot pull it out or if the trailing edge remains deep to be caught in the printer do not pull it by force Leave it there and go to the next step A WARNING There are extremely hot parts inside the Fuser Unit Do not touch any parts in the Fuser Unit or you will be burnt Also the mis fed media can be very hot Be careful not to get burnt when you remove it 2 Close the Exit Cover 1 3 Press down the blue levers 3 on both sides to unlock and open the Upper Unit 3 12 Chapter 3 Error Correction 4 Remove the mis feed media If the mis feed media does not exist close the Upper Unit 5 Open the Roll Deck Cover Hewind the roll onto the
29. which fits in the wall outlet of the installation location shall be conducted in accordance with the following N WARNING Select a power plug which meets the following criteria The plug has a voltage and current rating appropriate for the product s rating marked on its name plate The plug meets regulatory requirements for the area The plug is provided with a grounding pin or terminal If the appropriate plug does not fit the wall outlet in the installation the customer shall install an appropriate outlet Standard Usually found in IEC60320 C13 10A 250V IEC 15A 125V UL Plug Type Model Rating 220 240V Standard rre found in CEE7 7 10A 250V European countries countries o o AS NZS 3112 10A 250V Australia New Zealand GB1002 10A 250V China GB2099 1 IRAM 2073 10A 250V Argentina BS 1363 10A 250V United Kingdom SASO 2203 10A 250V Saudi Arabia BS 546A 15A 250V United Kingdom IS 1293 India SABS 1293 South Africa Chapter 1 Before Use page 1 1 Installation Requirements DRE ee RSP ae RR Met cud Mc O tM E DE LU HE Ta 2 1 2 Originals Prohibited from Duplication M du D DR E M MM Cn 12 3 1 3 Features 1 1 4 Specifications fon dee D im tae het op a P Ee fe M e E 1 5 1 4 1 General eene 1 5 1 4 2 Printer part coe reve CT 47 1 4 3 Scanner part E es Ne E A ANE ALIM DR RI HM UM O M di M
Download Pdf Manuals
Related Search