User Manual - Johnson Systems Inc.
Contents
1. An entrance control station Part Numbers CS SA ENT2B and CS SA ENT3B is typically installed at an entrance location and used to trigger a master control station into the ON DIM or OFF state The entrance station s and master station mimic each other when a button is pressed Wiring between a single or multiple entrance stations and master station requires 2 conductors for V and common and 3 conductors for the switches ON DIM and RST 1 conductor for each switch function A single DMX cable is required from the master control station to the DMX receiving device CS SA ENT3B CS SA ENT3 cs omx 12 iaaii i gii j lt oc rower surety common v neur neronen suero pose meur zd Mx our Wiring Two or More Master Control Stations Together with Take Control When two or more master control stations are controlling the same device DMX channels take control is typically required When a button is pressed on one of the master control stations it will automatically take control from the other master control stations and put them in the OFF state Wiring between the master control stations requires 2 conductors for V and common and 1 conductor for reset RST take control A DMX cable between the control stations is required along with a DMX cable from one of the master control stations to the DMX receiving device cs omx 12 cs omx2. User Manual CS DMX Series Programmable Manual DMX Stations JOHNSON SYSTEMS INC www johnsonsystems com 1923 Highfield Cres S E jary Alberta T2G SMI Canada 74 Caig tel 403 287 8003 fax 403 287 9003 infogjohnsonsystems com 1923 Highfield Cres Calgary Alberta T26 5 1 Canada tel 403 287 8003 fax 403 287 9003 Info johnsonsystems com Contents Warranty User Manual Copies Introduction Features CS DMX Series Control Station Diagrams ON DIM and OFF Buttons with Integral LED s Master M Slider Secondary 3 6 9 or 12 Sliders Control Station Security Feature Power Supply Requirement Control Station Wiring DMX Input and Output Wiring Wiring an Independent Control Station Wiring Single or Multiple Entrance Control Stations to a Master Control Station Wiring Two or More Master Control Stations Together with Take Control Wiring Two or More Control Stations Together with Mimic Mounting the Control Station Calibrate the DMX Output Range Configure the Control Station Using a CS IPRO Wireless Hand Held Programmer Time Fade Set the Adjustable Time Fade Set the Button LED Intensity Local Lockout Mode Activation Remote Lockout Mode Activation Short Circuit and Overload Protectior CS DMX Series Typical Wiring Applications EET 7 X 8 8 8 Warranty All CS DMX Series control stations come w
3. ON LED flashes on Set the Button LED Intensity The button LED intensity can be adjusted to a preferred intensity level for various environments NOTE Be sure the local and remote lockout modes are deactivated before adjusting the button LED intensity Procedure enter the button LED intensity adjust mode press and hold the ON and OFF buttons at the same time for approximately 10 seconds until all the button LED s illuminate Press the ON button to increase the button LED intensity Press and hold the ON button to accelerate the intensity adjustment Press the OFF button to decrease the button LED intensity Press and hold the OFF button to accelerate the intensity adjustment Once the preferred button LED intensity has been set press the ON and OFF buttons at the same time to exit the button LED intensity adjust mode and save the setting NOTE There is a minimum button LED intensity so the control station will always indicate its mode of operation state wwwjahnsonsustems com 4 1923 Highfield Cres S E Calgary Alberta 5 1 Canada tel 403 287 8003 fax 403 287 9003 Infosjohnsonsustems com Local Lockout Mode Activation When the local lockout mode is activated the control station is locked in the OFF state Any button press is ignored and the OFF LED flashes once to indicate local lockout mode is activated Procedure To activate the local l
4. Feature All CS DMX Series control stations have the capability to enable or disable the security feature Once security is enabled the security key programmed in the control station must match the security key in the CS IPRO programmer to be able to make programming changes to the control station The secutity feature eliminates the possibility for tampering with the control station programming The security feature is disabled by factory default If the security feature is required it should be implemented at the time of installation To enable the security feature set the SECURITY jumper JP2 in the ENABLE position Once installation of the CS DMX control station is completed refer to the CS IPRO user manual SECURITY menus EDIT KEY SET KEY and GET KEY for detailed programming and setup information The default 8 digit security key for all CS DMX Series control stations is set at all zeros 00000000 wwwjohnsonsystems com 5 4 on E p T 1923 Highfield Cres S E Calgary Alberta T26 5 1 Canada tel 403 287 8003 fax 403 287 9003 Infosjohnsonsustems com Power Supply Requirement The control station requires a regulated DC power supply from 10 6VDC to 18VDC A 12VDC power supply is recommended The power supply common V connects to the COM connection on J1 and the power supply positive V connects to the V connection on J1 Control Station Wiring CS DMX Series
5. 03 287 8003 fax 403 287 9003 Infosjohnsonsustems com Time Fade The control station is capable of fading from OFF ON ON e OFF OFF gt DIM DIM OFF The control station is capable of pseudo fading from DIM gt ON ON DIM The control station automatically begins fading when a button is pressed The button LED flashes and off once per second to indicate fading NOTE Pressing a button or adjusting the master slider level while the control station is fading cancels the fade and immediately activates the button pressed Set the Adjustable Time Fade The time fade can be adjusted from 0 to 60 seconds The factory default time fade is 5 seconds NOTE Be sure the local and remote lockout modes are deactivated before adjusting the time fade Procedure set the adjustable time fade press and hold the ON button for approximately 10 seconds until the ON LED extinguishes Release the ON button and count the number of times the ON LED flashes on Each time the ON LED flashes on 1 second of time fade is represented Once the required number of times the ON LED flashes on is counted press the ON button to save the time fade and exit To set the time fade to zero no fading press and hold the ON button for approximately 10 seconds until the ON LED extinguishes Release the ON button and immediately press the ON button again before the
6. 12 ese mour y eeu JA Um wwwjohnsonsystems com 7 4 1923 Highfield Cres S E Calgary Alberta 5 1 Canada nsa srs EE Wiring Two or More Control Stations Together with Mimic Mimic refers to pressing a button ON DIM or OFF on a control station and the other control station s are automatically triggered into the same ON DIM or OFF state The analog output s could be controlling the same device or completely different device Wiring between the control stations requires 2 conductors for V and common and 3 conductors 2 conductors for Part Number CS SA ENT2B for the switches ON DIM and RST 1 conductor for each switch function A DMX cable between the control stations is required along with a DMX cable from one of the master control stations to the DMX receiving device cs omx 12 cs omx 12 E BHL ser HA J ouxour Mounting the Control Station The control station can be mounted on in a gangable usually masonry type of back box with minimum depth of 2 50 8mm and a preferred depth of 3 5 88 9mm A 2 Phillips head screwdriver is required to secure the control station using the provided black 46 32 x 1 25 4mm mounting screws NOTE Ensure the back box is earth grounded to protect the control station from electrostatic discharge NOTE Ensure th
7. HBAWG igan 1 80 Wx275 Hx200 D 8 _ adjustable on voltage for stand alone applications 46cm x 70cm x 5 1cm CSSKENTEBA 5 1 gang 3 bution entrance sation igang 180 275 2000 wion preset and off A cm x 7 0cm x GSPRO Hand held Inrared Station Programmer Wireless 2757W x 4 95 H 10070 Tom x 1256m x 26cm DMX GPIM DMX 6 Port GIN TOUT Cascading Merger TAWVAG Wall Mount BSW X 12H X S50 24cm x Dem x 7 DMX or CATSE or Push Mount For other control products and solutions Sp please visit WWW JOHNSONSYSTEMS COM User Manual CS DMX Series Programmable Manual DMX Stations Rev 1 www johnsonsystems com plasa 5 ESTA member C Gi Calgary Alberta 2 SMI Canad 1923 Highfield Cres 54 tel 403 287 8003 fax 403 287 9003 infogjohnsonsystems com
8. and OFF Buttons With Integral LED s Master M Slider Infared LED Sensor Secondary 3 6 9 or 12 Sliders Arta non 3 6 Position Connector J1 For Power Supply Input COM V Button Contacts ON DIM RST Master Pot MP Analog Output DMX Output Range Calibration Jumper JP1 Security Enable Disable Jumper JP2 Factory Only Jumper s DMX Input Connector J1 DMX Output Connector 42 DMX Termination Jumper JP1 johnsonsystems com 4 1923 Highfield Cres S E Calgary Alberta 5 1 Canada tel 403 287 8003 fax 403 287 9003 Infosjohnsonsustems com ON DIM and OFF Buttons with Integral LED s All CS DMX Series control stations contain 3 buttons with integral blue LED s When a button is pressed the control station is triggered into the corresponding state The button LED s indicate the state of the control station Under normal operation when a bulton is pressed the corresponding LED will illuminate If the control station is fading the LED will flash once per second until the fade is complete Pressing a button or adjusting the master slider level while the control station is fading cancels the fade and immediately activates the button pressed The button LED s also indicate when local or remote lockout is active or if there is a sho
9. control stations can be wired for various applications The control station wiring can be configured for the functionality required A 6 position breakaway connector J1 is used to connect the power supply COM V three switches ON DIM RST as well as the master pot MP analog output not used with CS DMX Series control stations The recommended wire for these connections is stranded 18 AWG copper wire however smaller gauge wire may be suitable for some applications where distances are less than 150 50m The breakaway connector will accept wire sizes from 28 to 12 AWG Breakaway connectors are provided for all wiring terminations For proper termination the strip length should be 0 28 7mm A 1 8 3 2mm flat head screwdriver should be used to tighten the connections and torque to 3 5Lb In 0 4Nm DMX Input and Output Wiring All CS DMX Series have a 3 position breakaway connector used to receive DMX in DMX IN and 3 position breakaway connector used to transmit DMX out DMX OUT The DMX received on the DMX in if applicable connector is merged with the DMX generated by the control station and retransmitted through the DMX out connector Merged DMX data is highest takes precedence HTP for equivalent DMX control channels There is only a 1 packet 28msec delay in the retransmitted DMX from the original DMX received For proper termination the strip length should be 0 28 7mm A 1 8 3 2mm flat head scre
10. e back box mounting hole threads are not damaged Damaged threads on the back box can damage the threads on the mounting screws and cause stripping The back box threads can quickly be cleaned up by running a 6 32 tap through the mounting hole Be sure not to over tighten the mounting screws or this could result in stripping the back box mounting hole threads Calibrate the DMX Output Range All CS DMX Series control stations are factory calibrated for 0 100 DMX control with a 10 6VDC to 18VDC power supply If the control station does not have a full range of DMX control please consult a factory representative Configure the Control Station Using a CS IPRO Wireless Hand Held Programmer To configure the control station a Johnson Systems Inc Model Number CS IPRO wireless hand held programmer is required The CS IPRO is required primarily to configure the DMX channel patch for each of the sliders however it provides several other useful features Wireless communication between the CS IPRO and CS DMX Series control stations is via bidirectional infrared LED s The control station infrared LED window is located between the master M slider and slider 1 The maximum range for sending and receiving data between the control station and CS IPRO is 12 30cm NOTE Refer to the CS IPRO user manual for detailed programming information wwwjohnsonsustems com 4 1923 Highfield Cres Calgary Alberta 5 1 Canada tel 4
11. ith a standard one 1 year limited warranty against defects in parts and workmanship User Manual Copies Additional copies of the most recent version of this manual can be downloaded at http www johnsonsystems com pdf_files jsi_cs_dmx_manual_rev_1 pdf Note Refer to the CS IPRO user manual for detailed programming information wwwjohnsonsystems com 1923 Highfield Cres S E Calgary Alberta T26 5 1 Canada e Hue CS DMX Series Programmable Manual DMX Station CSJPRO Wireless Hand held Programmer Introduction Multi Station multi room manual DMX controls for a full DMX universe of control Value power and complete flexibility in a green user friendly cost effective package The DMX Series of controls are the most capable manual stand alone DMX controls available These field programmable controls support 512 channels of DMX data with digitally adjustable fade times Multiple stations can be daisy chained together on the same control wire permitting multiple stations room Each station can be individually programmed with our wireless infrared hand held programmer Model Number CS IPRO permitting any slider channel assignments imaginable Available from single to 12 channels with master preset and take control functions Two and three button entrance station can be remotely locked out for application where access needs to be limited This series of controls will operate on DC s
12. ockout mode press and hold the OFF button for approximately 10 seconds until the OFF LED extinguishes To deactivate the local lockout mode press and hold the OFF button for approximately 10 seconds until the OFF LED illuminates Remote Lockout Mode Activation When the remote lockout mode is activated the control station ignores all remote control station key presses The active LED flashes off for 0 1 seconds every 2 seconds to indicate remote lockout mode is activated Procedure To activate the remote lockout mode press and hold the DIM button for approximately 10 seconds until the DIM LED flashes off for 0 1 seconds deactivate the remote lockout mode press and hold the DIM button for approximately 10 seconds until the DIM LED flashes off for 0 1 seconds Short Circuit and Overload Protection The control station is equipped with short circuit and overload protection The short circuit limit is set at 100 with 0 6W of power dissipation When a short circuit or overload is detected while in the ON or DIM state all of the button LED s flash on and off to indicate there is short circuit or overload condition The control station automatically recovers to normal operational state once the short circuit or overload is removed wwwjohnsonsystems com 1923 Highfield Cres S E Calgary Alberta 5 1 Canada tek 03 207 005 fax 403 287 9003 JOHNSON SYSTEMS INED J Inf
13. osjonnsonsstemis com CS DMX Series Typical Wiring Applications et e 2 ese omver 20 VAC RACK RACK CL Ge ee 3 wx owes mm MERGER Jud Bune p jede s a Ex oe Brel i I I EJ E E I gr ati wwwjahnsonsustems com n CS DMX Series Programmable Manual DMX Stations Model Description Wires Back Box Minimum PCB Clearance gl 1 gang 3 channel manual control ZXHBAWG 2gang 360 x275 Hx 200D x wimaster slider on preset and off x 7 0cm x5 tem ii 2gang 6 channel manual control ZXHBAWG Sgang 550W x275 Hx 200D wimastor slider on preset and off E 14 00m x Z0cm x 5 39870 9channel manual contol ZXHBAWG 4gang T30WX27SHx200D MMT wimaster slider on preset and off 18 50m x Z0cm x 5 1em CSOMXA23 EIL 4 gang 12 channel manual control ZXHBAWG Sgang S10WXx27S9 Hx200D BAAN master sider on preset and off E 23 tem x 7 00m GSSKENTZSA a T gang 2 buton onoff entrance station with SX
14. rt circuit overload condition refer to page 10 for details The intensity of the button LED s can be adjusted refer to Set the Button LED Intensity on page 9 Pressing the ON button triggers all of the DMX channels patched to the sliders to full on The ON button corresponds with the ON connection on J1 and is optionally connected to other control stations for various applications Pressing the DIM button activates DMX output control from the slider potentiometers pots The DIM button corresponds with the DIM connection on J1 and is optionally connected to other control stations for various applications Pressing the OFF button turns off zero percent 00 output level all of the DMX channels patched to the sliders The OFF button corresponds with the RST reset connection on J1 and is optionally connected to other control stations for various applications NOTE The control station will still transmit DMX output levels at zero percent 00 in the OFF state Master M Slider The master slider controls the overall maximum DMX output level for the secondary sliders It has similar functionality to a grand master slider found on some DMX control consoles Secondary 3 6 9 or 12 Sliders Each of the secondary sliders control the DMX output level for all the DMX channels patched to the slider Each slider can be configured to control any combination of 512 DMX channels Control Station Security
15. upply voltages up to 18 volts Adjustable time fade and LED intensity allow customization for demanding applications Durable powder coat finish is available in either black or white Features Manual DMX at your fingertips Six models sizes available including two and three button entrance stations 512 DMX channels of control per station Multiple stations can be daisy chained on the same DMX line Digitally adjustable fade times and LED brightness Station programming via low cost wireless infrared hand held remote Local or remote entrance station lockout options Short circuit and over current protection Ruggedly built for reliability and longevity Tough durable powder coat paint on 0 080 aluminum laser cut faceplate for a scratch resistant non glare finish Color matched and sized for use with Johnson Systems AP Series adapter plates where necessary to adapt to existing larger electrical back boxes Metal shaft sliders and machine screw mounting help prevent broken or missing parts Heavy duty high tactile pushbutton switches are rated for 5 million operations Optional 6 Port Cascading Installation Merger permits low cost DMX universe combining wwwjohnsonsystems com 3 1923 Highfleld Cres S E Calgary Alberta 5 1 Canada tel 03 257005 fax 403 287 9003 JOHNSON SYSTEMS INED J Infosjonnsonsstemis com CS DMX Series Control Station Diagrams ON DIM
16. wdriver should be used to tighten the connections and torque to 3 5Lb In 0 4Nm Be sure to isolate and protect all shield wires and comply with standard RS 485 termination practices DMX IN SHIELD COMMON DATA DATA is terminated on the J1 connector OUT SHIELD COMMON DATA DATA is terminated on the J2 connector Complies with USITT DMX512 A ANSI E1 11 2008 standard protocol for digital data control Recommended cable is Beldon 9829 9842 Cat 5 or equivalent low capacitance twisted pair Wiring must follow a daisy chain topology Maximum of 32 receiving devices on a single DMX line Maximum cable length is 1 500 feet 455 meters For more information Google DMX or visit http Www usitLorg DMX512FAQ aspx NOTE For long DMX lines exceeding 1 000 feet 305 meters the DMX TERM jumper JP1 should be in the terminated upper position NOTE Be sure the last DMX receiving device end of line is terminated with 1000 to 1200 resistor wwwjohnsonsystems com 1923 Highfield Cres S E Calgary Alberta 5 1 Canada Jonson 18 SI EIU AE Wiring an Independent Control Station independent control station requires 2 conductors for V and common and a single DMX cable for the DMX out connection Boum p LEM lt oc POWER SUPPLY COMMON v INPUT B e S ta Wiring a Single ar Multiple Entrance Control Stations to a Master Control Station
Download Pdf Manuals
Related Search