Moxa PRP/HSR Redundancy Box User`s Manual
Contents
1. Do Apply System Up Time Indicates how long the Moxa PRP HSR RedBox remained up since the last cold start Current Time User specified time Indicates time in yyyy mm dd format Clock Source Setting pescripton O actor Defeat Time Zone Time zone Specifies the time zone which is used to determine the local GMT Greenwich time offset from GMT Greenwich Mean Time Mean Time Daylight Saving Time The Daylight Saving Time settings are used to automatically set the Moxa PRP HSR RedBox s time adjustments according to national standards Start Date User specified date Specifies the date that Daylight Saving Time begins End Date User specified date Specifies the date that Daylight Saving Time ends 3 7 PRP HSR Redundancy Box Featured Functions Offset User specified hour Specifies the number of hours that the time should be set None forward during Daylight Saving Time NOTE Changing the time zone will automatically correct the current time Be sure to set the time zone before setting the time Time Server IP Name IP address or name of The IP or domain address e g 192 168 1 1 time server time stdtime gov tw or time nist gov IP address or name of The Moxa PRP HSR RedBox will try to locate the secondary NTP secondary time server server if the first NTP server fails to connect Enable NTP SNTP Server Enable Disable Enables SNTP NTP server functionality for client2. lt STRING month gt The date when summer time offset daylight savings time ends multicast filter addr lt UINT index gt set multicast filter address lt MACADDR MacAddress gt multicast filter src port lt UINT index gt Set source port of the multicast priority entry lt UINT port gt multicast filter mac compare length Set Compared length of multicast address lt UINT index gt lt UINT len gt vlan filtering vid list lt STRING vlanids gt setting VLANs list vian filtering vid add remove lt STRING vlanids gt VLAN filtering parameters Configuration Redundancy Commands Display Information entryforgettime Set Entry forget time Configuration Port Interface Commands Display Information Set hardware interface as SGMII or 1000BaseX hw_interface SGMII 1000BasexX B 2
3. 02 Upgrade Firmware From o Browse E e Select i 3 13 PRP HSR Redundancy Box Featured Functions Configuration Backup and Restore The Moxa PRP HSR RedBox supports 3 ways to back up and restore a configuration file to from a local database remote TFTP Server and Auto Backup Configurator ABC 02 Configuration Backup and Restore Local TFTP Server Auto Backup Configurator ABC 0 Backup Configuration File to Local Device Restore Configuration From Browse Auto load configuration from ABC to system when boot up E Auto backup to ABC 02 when configuration change Apply Local 1 Click the Backup button to back up the configuration file to the local database 2 Browse for the configuration file from the local database and then press the Restore button TFTP Server 1 Enter the TFTP Server IP 2 Input the backup restore file name supports up to 54 characters including ini and then press the Backup Restore button Auto Backup Configurator ABC 02 1 4 Click Backup to save the configuration file to the ABC 02 The file will be saved in the Moxa folder of the ABC 02 The file name is Sys ini The configuration file will be saved to the ABC 02 USB s Moxa folder as two independent files named Sys ini and MAC ini The purpose of saving to two files is to identify the file while using Auto load configuration from ABC to system when boot up Note MAC ini is named us
4. 14122917 A A A O anaen eT EOM G103 quit Exit command line interface exit Exit command line interface reload Halt and perform a cold restart terminal Configure terminal page length copy Copy from one file to another save Save running configuration to flash ping Send echo messages clear Clear information show Show running system information configure Enter configuration mode sslcertgen Generate SSL certificate sshkeygen Generate SSH host key EOM G103 State OPEN mM Mo m Ready 1 13 R923 The Telnet console looks and operates in precisely the same manner as the USB console Configuration by Web Browser NOTE NOTE NOTE NOTE The Moxa PRP HSR RedBox s web console is a convenient platform for modifying the configuration and accessing the built in monitoring and network administration functions You can open the Moxa PRP HSR RedBox s web console using a standard web browser such as Internet Explorer To connect to the Moxa PRP HSR RedBox s Telnet or web console your PC host and the Moxa PRP HSR RedBox must be on the same logical subnet If the Moxa PRP HSR RedBox is configured for other VLAN settings you must make sure your PC host is on the management VLAN When connecting to the Moxa PRP HSR RedBox s Telnet or web console first connect one of the Moxa PRP HSR RedBox s Ethernet ports to your Ethernet LAN or directly to your PC s Ethernet port You may use either a straight through or cross over Etherne
5. 5 PRP HSR Redundancy Box Featured Functions DNS IP Address IP address for DNS Specifies the IP address of the DNS server used by your None server network After specifying the DNS server s IP address you can use the Moxa PRP HSR RedBox s URL e g www PT company com to open the web console instead of entering the IP address IP address for 2nd DNS Specifies the IP address of the secondary DNS server used by None server your network The Moxa PRP HSR RedBox will use the secondary DNS server if the first DNS server fails to connect IPv6 Global Unicast Address Prefix Prefix Length 64 bits Default Gateway Global Unicast Address The prefix value must be formatted according to the RFC 2373 None Prefix IPv6 Addressing Architecture using 8 colon separated 16 bit hexadecimal values One double colon may be used in the address to indicate the appropriate number of zeros required to fill the undefined fields IPv6 Global Unicast Address Displays the IPv6 Global Unicast address The network portion None of the Global Unicast address can be configured by specifying the Global Unicast Prefix and using an EUI 64 interface ID in the low order 64 bits The host portion of the Global Unicast address is automatically generated using the modified EUI 64 form of the interface identifier PRP HSR RedBox s MAC address IPv6 Link Local Address The network portion of the Link Local address is FE80 and the None h
6. A odiar n ra oo e e a EAn OEE OOA O EAn O An N OONO Oee 3 15 Ber Ho gy ah as I ne te Te ten TER Tet ye RA RI EA RG SOUR E TEA Nt ene TEC MeN Ted PTR TIN TURRET eC 3 15 SEAN a seqatucscecacenecedaaumadecesaeatucecssaceneceaas mudecesaqatececacaceaececas muceautauetecccateaaers 3 15 Virtual LAN VEAN FICS FIN po 3 16 PO satellite alada deda dede dada dodo dede nte A dede deda toda detected 3 16 PONE SCUINGS eorn rar a oT ore anatanuvorervovetannlanavauavovardval ant rnavouadere oral anatauuuorey EEO aD 3 16 POr Es aaa 3 17 ReGUTIGan GP rOtO CO ies cnt cai ci ie cat aN ee ce ct NG ce EON 3 17 MIC EFI tr oo 3 18 Secta tna batata atan aaa baaa ies AU Ds ats pie gts es ica 3 19 E A E EE ERRE 3 19 Ma apagement FEST ACS A a aes ea ais a alas 3 20 TrRUSted ACCOSS iii a 3 21 Autentica Estructura lenta a 3 22 NM cdas 3 22 SNMP REAG WERE SENING Stic A Aa 3 23 apoc ihe go ener rer rr eCr CTC ETRE CRETE CCPC Cr NENE NEO AAA ELECT TET AA 3 24 Diagnostic 3 25 LIE Re A TER EREI O O O A I E SENA 3 25 FETUS A A A A colette colette A AA AEA A ARAT AEA A AA AEA A A AA A A A E cadet cadet cadet cadet A 3 26 PORE MIIR O e a aaa 3 26 Monto nds AAA 3 27 CPU Memory UU ds 3 27 dd e OEA RELE AEREO ERRE REE RRE RR ERRE RARE RARE ete ete ehh heheh ehhh ehh iene Gents E ERE CERER O 3 29 A wrdapntuandnrniudnsanndnandni dads ausndndnauauan Manin dy deandyduandndnauaneannareadaaeananduasdaneaucncasnaraosaeanangugndth 3 31 A O O A A EEA 3 32 SA A Cee
7. Device Name Managed Redundancy Box gt VLAN Device Location Device Location Port Device Description EOM G103 System Up Time 0d19h6m6s Redundant Protocol y j gt Multicast Redundancy Protocol PRP Security SNMP cio Event Log More Diagnostics 9 Port Interlink link on Monitoring admin Auth ok Port EthConsole link on 192 168 127 100 admin Auth ok Configuration change activated Port EthConsole link off User moxa login Auth fail by Tacacs Authentication fail 172 26 4 11 admin Auth ok goahead WEBSERVER Best viewed with IE 7 above at resolution 1024 x 768 System Settings The System Settings section includes the most common settings required by administrators to maintain and control a Moxa PRP HSR RedBox System Information Configure the following System Information to make it easier to identify different PRP HSR RedBoxes connected to your network system Information Device Name Managed Redundancy Box Device Location Device Location Device Description PT 6503 Contact Information Apply Device Name Max 30 characters This option is useful for differentiating between the roles or applications of different units Example Factory PRP HSR RedBox 1 Device Location Max 80 characters This option is useful for differentiating between the locations of PRP HSR RedBox different units Example production line 1 Location 3 2 PRP HSR Redundancy Box Featured Functions De
8. IEEE 802 11AB LLDP standardizes the self identification advertisement method and allows each networking device such as a Moxa managed PRP HSR RedBox to periodically send its system and configuration information to its neighbors Because of this all LLDP devices are kept informed of each other s status and configuration and with SNMP this information can be transferred to Moxa s MXview for auto topology and network visualization purposes From the PRP HSR RedBox s web interface you can enable or disable LLDP and set the LLDP transmit interval In addition you can view each PRP HSR RedBox s neighbor list which is reported by its network neighbors Most importantly enabling the LLDP function allows Moxa s MXview to automatically display the network s topology and system setup details such as VLAN and Trunking for the entire network 3 25 PRP HSR Redundancy Box Featured Functions Configuring LLDP Settings LLDP W Enable LLDP Message Transmit Interval sec SO Apply Neighbor ID Neighbor Port Neighbor Port Description Neighbor System General Settings LLDP Enable or Disable Enables or disables the LLDP function Enable Message Transmit Interval Factory Default 5 to 32768 sec Sets the transmit interval of LLDP messages in seconds 5 seconds LLDP Table The LLDP Table displays the following information Neighbor Port Description A textual description of the neighbor device s interface Neigh
9. VLANs are easier to manage 3 15 PRP HSR Redundancy Box Featured Functions Virtual LAN VLAN Filtering What is VLAN Filtering The Moxa PRP HSR RedBox supports a virtual LAN filtering function The VLAN filtering function is enabled on the Interlink port By adding the VLAN ID in the VLAN field the interlink port will only forward packets that have this VLAN ID Packets that do not have this VLAN ID will be dropped VLAN Filtering C Enable VLAN Filtering Apply Source Interlink Enable VLAN Filtering Enable Disable Enables or disables the VLAN filtering function VLAN VLAN ID ranges from 1 Set the VLAN IDs using commas to differentiate different None to 4094 VIDs that will be filtered by the interlink port this product Supports up to 256 VLAN groups Port Port Settings Port settings are included to give the user control over port access port transmission speed flow control and port type MDI or MDIX Port Settings Media Type MDUMDIX A MODOTX RJA5 E Auto Y Auto B i D00TX R J45 WW Auto Auto Interlink 1000TX R J45 Auto Auto Media Type Media type Displays the media type for each module s port Description Max 63 characters Specifies an alias for the port to help administrators None differentiate between different ports Example PLC 1 3 16 PRP HSR Redundancy Box Featured Functions Speed Allows the port to use the
10. eer ee E rrr Tre Cer ee Crr errr er rT TT er Tre Corer ETET TET CCC TCE TERT TEE CT TC Tre Creer ererT Tn er rrr 3 33 A MIB Group ico A 1 B CLI Command Support for the EOM G103 PHR PTP Module sssssss2222 B 1 BA em Gre g alag alata komme mace na In B 1 SHOW COMMING ia A A A A A oetadasetre ume B 1 Configuration Gre gaya ads ra rere reer ere er esr eee ee PEP NOT Tere TTS TNE CEPI TUN OPE EIIN ESSE IS T B 2 Configuration Redundancy COMMON ds retener ro EINEN E SEE E IDEAS EEES ERES ES EE EID EEE EEE orina B 2 Configuration Port Interface COMMAnNdsS 000ccccccccncccocnncnnccn cnn rr B 2 1 About this Manual Thank you for purchasing a Moxa managed Ethernet PRP HSR RedBox Read this user s manual to learn how to connect your Moxa PRP HSR RedBox to Ethernet enabled devices used for industrial applications The following two chapters are covered in this user manual O Chapter 2 Getting Started This chapter explains the initial installation process for the Moxa PRP HSR RedBox There are three ways to access the Moxa PRP HSR RedBox s configuration settings the USB console command line interface and web based interface O Chapter 3 Featured Functions This chapter explains how to access the Moxa PRP HSR RedBox s various configuration monitoring and administration functions These functions can be accessed by serial Telnet command line or web based interface The web based interfac
11. introduce the functions There are only a few differences between the web console USB console and Telnet console The following topics are covered in this chapter 0 0 a Home System Settings System Information User Account Network Date and Time Warning Notification MAC Address Table System Files Y Y VV VV V Y Restart Factory Default VLAN gt Virtual LAN VLAN Filtering Port gt Port Settings gt Port Status Redundant Protocol Multicast Filtering Security gt Login Authentication gt Management Interface gt Trusted Access gt Authentication Certificate SNMP gt SNMP Read Write Settings gt Trap Settings Diagnostics gt LLDP gt Ping gt Port Mirror Monitoring gt CPU Memory Utilization gt Statistics gt Fiber Check gt Event Log System Services PRP HSR Redundancy Box Featured Functions Home The Home page shows a summary of the Moxa PRP HSR RedBox information including System Information Redundancy Protocol Event log and Device virtualization panel With an organized key summary operators can easily understand the system and port link status at a glance MOXA PowerTrans EOM G103 Series www moxa com Model EOM G103 P 17221237 MAC Address 00 90 E8 05 03 07 PWR2 Name Managed Redundancy Box Serial No moxa00050307 Firmware Version V4 0 build 14122917 1 FAULT Location Device Location ABC 02 USB T Device Not Present HSR COUPLING Home System
12. of ingress packet of the multicast MAC address 3 18 PRP HSR Redundancy Box Security Featured Functions Security can be categorized into two levels user name password level and port access level The Moxa PRP HSR RedBox provides a number of different security functions including Login Authentication Management Interface Trusted Access Authentication Certificate IEEE 802 1A Port Security and Loop Protection Login Authentication The Moxa PRP HSR RedBox provides two different user login options Terminal Access Controller Access Control System Plus TACACS and Remote Authentication Dial In User Service RADIUS The TACACS and RADIUS mechanisms are centralized AAA Authentication Authorization and Accounting systems for connecting to network services The fundamental purpose of both TACACS and RADIUS is to provide an efficient and secure mechanism for user account management Login Authentication Authentication Protocol Server IP Name TCP Port Shared Key Authentication Type Timeout sec Login Authentication Authentication Protocol Server IP Name UDP Port Shared Key Authentication Type Timeout sec RADIUS TACACS 49 ASCH Apply RADIUS TACACS Authentication Protocol Authentication protocol selection TACACS Server IP Name TCP UDP Port Shared Key Authentication Type Timeout sec Set the IP address of an external TACACS RADIUS
13. only or read write permissions using the community strings public and private by default SNMP V3 requires that you select an authentication level of MD5 or SHA and is the most secure protocol You can also enable data encryption to enhance data security Supported SNMP security modes and levels are shown in the following table Select the security mode and level that will be used to communicate between the SNMP agent and manager Protocol A e Authentication Encryption Version SNMP V1 V1 V2c Read Community string No Uses a community string match for V2c Community authentication N V1 V2c Community string O Uses a community string match for Write Read authentication Community SNMP V3 No Auth No No Uses an account with admin or user to access objects O MD5 or SHA Authentication N Provides authentication based on HMAC MD5 based on MD5 or or HMAC SHA algorithms 8 character SHA passwords are the minimum requirement for authentication MD5 or SHA Authentication Provides authentication based on HMAC MD5 based on MD5 or encryption or HMAC SHA algorithms and data encryption SHA key key 8 character passwords and a data encryption key are the minimum requirements for authentication and encryption These parameters are configured on the SNMP page A more detailed explanation of each parameter is given below the figure 3 22 PRP HSR Redundancy Box Featured Functions SNMP SNMP Versions V1 V2c V3 Admin A
14. 100 Net ID LAN ID Settings Entry Forget time ms 100 Net ID 1 LAN ID gt Apply Protocol PRP HSR Select redundancy protocol Coupling QuadBox Only available on the PT G503 PHR PTP series 3 17 PRP HSR Redundancy Box Featured Functions Entry Forget time ms 10 100 Select 100 ms for 100M and 10 ms for 1000M Net ID only available on the PT G503 PHR PTP series Allows the user set a Net ID ranging from 1 to 7 Coupling Auto mode only LAN ID A B Allows the user to set a LAN ID Coupling mode only Multicast Filtering The Moxa PRP HSR RedBox provides a multicast filtering function You can enable the source port and set it to drop or forward ingress traffic that comes from the designated port with a specific multicast MAC address Multicast filtering Action Drop Apply Priority Index 1 Source Port El Interlink Port E AB Port MAC Address 3 pe E a ia Compared Length Bytes Apply Tee noe x Action Drop Forward The RedBox will drop or forward traffic depending on the setting Priority Index Setting Description Factory Default Items with priority 1 will be acted on first followed by items 1 with priority 2 etc Source Port Interlink Port or A B Multicast filtering applies to the source port None MAC Address MAC Address Input the multicast MAC address None Compared Length Bytes Between 1 and 6 bytes The RedBox will compare the first x None bytes
15. IEEE 802 3u protocol to negotiate Auto with connected devices The port and connected devices will determine the best speed for that connection 1G Full Choose one of these fixed speed options if the connected 100M Full Ethernet device has trouble auto negotiating for line speed 10M Full MDI MDIX Auto Allows the port to auto detect the port type of the connected Auto Ethernet device and change the port type accordingly Port Status The following table shows the status of each port including media type link status flow control and port state Port Status Media Type Link Status MDIMDIX Status Port State A 1000TxX R J45 Link Down B 1000TX R J45 Link Down Interlink 1000TX R J45 100M Full MDI Forwarding EthConsole 1000TX R J45 Link Down Redundant Protocol The Moxa PRP HSR RedBox supports four redundant protocols PRP HSR Coupling and QuadBox Depending on the topology of your network you can choose one of these redundancy protocols All four protocols support a 0 ms recovery time PRP Copies of each packet are sent from the source to the destination via two LANS HSR Copies of each packet are sent from the source to destination via an HSR ring Coupling Coupling is used to connect PRP and HSR QuadBox QuadBox is used to connect two HSR rings Only available on the PT G503 PHR PTP series Redundant Protocol Protocol PRF Status Active Protocal PRP Entry Forget time ms
16. IP address and subnet mask as well as the IP address of the default gateway In addition input cells are provided for the IP addresses of a 1st and 2nd DNS server The IPv6 settings include two distinct address types Link Local Unicast addresses and Global Unicast addresses A Link Local address makes the PRP HSR RedBox accessible over IPv6 for all devices attached to the same local subnet To connect to a larger network with multiple segments the PRP HSR RedBox must be configured with a Global Unicast address IP Settings Get IP From Manual IP Address 190 168 127 053 subnet Mask 24 255 255 255 0 Default Gateway pO ist DNS Server PO 2nd DNS Server pO IPv6 Global Unicast Address Prefix IPv6 Global Unicast Address IPv6 Link Local Address feig 2 OO e8 fT e0026 Get IP From DHCP The Moxa PRP HSR RedBox s IP address will be assigned DHCP BOOTP The Moxa PRP HSR RedBox s IP address will be assigned A AAA IP Address IP address for the Moxa Assigns the Moxa PRP HSR RedBox s IP address on a TCP IP 192 168 127 253 PRP HSR RedBox network Subnet Mask Subnet mask for the Identifies the type of network the Moxa PRP HSR RedBox is 24 255 255 255 0 Moxa PRP HSR RedBox connected to e g 255 255 0 0 for a Class B network or 255 255 255 0 for a Class C network Default Gateway IP address for gateway Specifies the IP address of the router that connects the LAN to None an outside network 3
17. Moxa PRP HSR Redundancy Box User s Manual First Edition March 2015 www moxa com product MOXA 2015 Moxa Inc All rights reserved Moxa PRP HSR Redundancy Box User s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement Copyright Notice Trademarks 2015 Moxa Inc All rights reserved The MOXA logo is a registered trademark of Moxa Inc All other trademarks or registered marks in this manual belong to their respective manufacturers Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa Moxa provides this document as is without warranty of any kind either expressed or implied including but not limited to its particular purpose Moxa reserves the right to make improvements and or changes to this manual or to the products and or the programs described in this manual at any time Information provided in this manual is intended to be accurate and reliable However Moxa assumes no responsibility for its use or for any infringements on the rights of third parties that may result from its use This product might include unintentional technical or typographical errors Changes are periodically made to the information herein to correct such errors and these changes are incorporated into new editions of the publication Technical Su
18. WR2 Name Managed Redundancy Box Serial No moxa00050340 Firmware Version V4 0 build 14062411 STATE FAULT Location Device Location ABC 02 USB T Device Not Present PRP HSR QUADBOX COUPLING Home 1 gt System Device Name Managed Redundancy Box gt VLAN Device S Device Location Port Device Description PT G503 System Up Time 6d4h33m21s Redundant Protocol Multicast ae en E Redundancy Protocol PRP oO Hora Security a I Save emg Port EthConsole link off a Monitoring Port EthConsole link on Port Interlink link off Port Interlink link on Port EthConsole link off Port EthConsole link on i Port EthConsole link off 4 172 21 2 13 admin Auth ok i 172 21 2 13 admin Auth ok PRP HSR PoworTrans A PT GSO PHR PTP goahead WEBSERVER Best viewed with IE 7 above at resolution 1024 x 768 2 6 3 Featured Functions In this chapter we explain how to access the Moxa PRP HSR RedBox s various configuration monitoring and administration functions These functions can be accessed by serial Telnet or web console The USB console can be used if you do not know the Moxa PRP HSR RedBox s IP address and requires that you connect the Moxa PRP HSR RedBox to a PC COM port The Telnet and web consoles can be opened over an Ethernet LAN or the Internet The web console is the most user friendly interface for configuring a Moxa PRP HSR RedBox In this chapter we use the web console interface to
19. bor System Hostname of the neighbor device The Ping function uses the ping command to give users a simple but powerful tool for troubleshooting network problems The function s most unique feature is that even though the ping command is entered from the user s PC keyboard the actual ping command originates from the Moxa PRP HSR RedBox itself In this way the user can essentially sit on top of the Moxa PRP HSR RedBox and send ping commands out through its ports To use the Ping function type in the desired IP address and then press Enter from the Console utility or click Ping when using the Web Browser interface Ping edito ES Port Mirror The Port Mirror function can be used to monitor data being transmitted through a specific port This is done by setting up another port the mirror port to receive the same data being transmitted from or both to and from the port under observation Using a mirror port allows the network administrator to sniff the observed port to keep tabs on network activity 3 26 PRP HSR Redundancy Box Featured Functions Port Mirroring Monitored Port A B Interlink Sniffer Mode RX Mirror Port Eth Console Port Port Mirroring Settings Setting Description OO Monitored Port Select the ports whose network activity will be monitored Multiple port selection is acceptable Sniffer Mode e RX Select this option to monitor only those data packets coming into the Moxa PRP HSR RedBox s port The Et
20. ckets that did not pass TCP IP s error checking algorithm The Total Packets option displays a graph that combines TX RX and TX Error RX Error Packet activity The graph displays data transmission activity by showing Packets s i e packets per second or pps versus sec seconds In fact three curves are displayed on the same graph Uni cast packets in red color Multi cast packets in green color and Broad cast packets in blue color The graph is updated every few seconds allowing the user to analyze data transmission activity in real time Statistics All Pots Total Packets Clear Packetisec 40 a2 Unicast Mulicast Broadcast pie Format Total Packets Packets in past 5 secs Update Interval every 5 secs 1 0 0 0 0 0 0 0 0 E 2 16927 54 0 0 25077 50 0 0 3 0 0 0 0 0 0 0 0 4 0 0 0 0 0 0 0 0 9 0 0 0 0 0 0 0 0 6 0 0 0 0 0 0 0 0 T 1375 1 0 0 164 0 0 0 5 G1 0 0 0 0 0 0 0 0 6 0 0 0 0 0 0 040 Fs 3 29 PRP HSR Redundancy Box Featured Functions Monitor by Port Access the Monitor by Port function by selecting FE or GE Ports or Port i in which i 1 2 G2 from the left dropdown list The Port i options are identical to the Monitor by System function discussed above in that users can view graphs that show All Packets TX Packets RX Packets or Error Packets activity but in this case only for an individual port The All Ports option is essentially a graphical display of the individual port acti
21. count To create a new account input the user name and password and assign the desired level of authority Once you apply the new settings the new account will appear in the Account List table User Name User Name None Max of 30 characters Password Password for the user account None Minimum requirement is 4 characters maximum of 16 characters Modifying an Existing Account Select the existing account from the Account List table Modify the details accordingly and then apply the settings to save the configuration User Account Active Authority admin User Name admin Old Password Password SNMPv3 requires 8 characters password Confirm Password Account List MESS ESTE E US user user Delete Deleting an Existing Account Select the existing account from the Account List table and then press the delete button to delete the account User Account Sars Acie pamicatty e Would you like to delete account tertuserl User Name Old Password Confirm Password Apply Account List User Name a ae admin admin user Ear Diete Le aa e 3 4 PRP HSR Redundancy Box Featured Functions Network Network configuration allows users to configure both IPv4 and IPv6 parameters for management access over the network The Moxa PRP HSR RedBox supports both IPv4 and IPv6 and can be managed through either of these address types IP Setting The IPv4 settings include the PRP HSR RedBox s
22. current configuration to the ABC 02 s His_ini folder The file name is created from the system date time in the following format MMDDHHmm ini Note MM month DD day HH hour mm minutes from the system time Log File Backup The Moxa PRP HSR RedBox reset button allows users to quickly back up files to the ABC 02 Simply press the Reset button on top of the RedBox to force the RedBox to start backing up the current system configuration files and event logs to the ABC 02 NOTE DO NOT remove the ABC 02 while performing upgrade backup or restore functions Restart This function provides users with a quick way of restarting the system Restart This function will restart the system Apply Factory Default This function provides users with a quick way of restoring the Moxa PRP HSR RedBox s configuration to factory defaults You can apply this function from the USB serial Telnet web based consoles or using the hardware reset button Factory Default Warning The switch will be resetto factory default and then restart Apply NOTE After restoring the Moxa PRP HSR RedBox to the factory default configuration you will need to use the default network settings to re establish a web or Telnet console connection with the Moxa PRP HSR RedBox VLAN Setting up Virtual LANs VLANs on your Moxa PRP HSR RedBox increases the efficiency of your network by dividing the LAN into logical segments as opposed to physical segments In general
23. de the SNMP agent sends an SNMPv1 trap PDU to the NMS No acknowledgment is sent back from the NMS so the agent has no way of Knowing if the trap reached the NMS SNMP Trap Mode Inform SNMPv2 provides an inform mechanism When an inform message is sent from the SNMP agent to the NMS the receiver sends a response to the sender acknowledging receipt of the event This behavior is similar to that of the get and set requests If the SNMP agent does not receive a response from the NMS for a period of time the agent will resend the trap to the NMS agent The maximum timeout time is 300 sec default is 1 sec and the maximum number of retries is 99 times default is 1 time When the SNMP agent receives acknowledgement from the NMS it will stop resending the inform messages Host IP Address 1 3 24 PRP HSR Redundancy Box Featured Functions IP or name Specifies the IP address or name of the primary trap server None used by your network ist Trap Community Max 30 characters Specifies the community string to use for authentication Host IP Address 2 IP or name Specifies the IP address or name of the secondary trap server None used by your network 2nd Trap Community Max 30 characters Specifies the community string to use for authentication Diagnostics The Moxa PRP HSR RedBox provides three important tools for administrators to diagnose network systems LLDP Overview LLDP is an OSI Layer 2 protocol defined by
24. dresses of related ports Select this item to show all MAC addresses of related ports Port Interlink Select this item to show all MAC addresses of related ports Port Ethernet Select this item to show all MAC addresses of related ports 3 12 PRP HSR Redundancy Box Featured Functions The table displays the following information This field shows the MAC address This field shows the type of this MAC address Port sd This field shows the port that this MAC address belongs to System Files Firmware Upgrade The Moxa PRP HSR RedBox supports 3 ways to upgrade the up to date firmware including local database remote TFTP Server and Auto Backup Configurator ABC 02 Firmware Upgrade Local TFTP Server Auto Backup Configurator ABC 02 Upgrade Firmware From Local 1 Download the updated firmware rom file from Moxa s website www moxa com 2 Browse for the rom file and then press the Upgrade button TFTP Server 1 Enter the TFTP Serve IP 2 Input the firmware file name rom and press the Upgrade button Auto Backup Configurator ABC 02 1 Download the updated firmware rom file from Moxa s website www moxa com 2 Save the file to the ABC 02 Moxa folder The file name cannot be longer than 8 characters and the file extension must be rom 3 Browse for the ABC 02 firmware and then press the Upgrade button Firmware Upgrade Local TFTP Server Auto Backup Configurator ABC
25. e is the most user friendly way to configure the Moxa PRP HSR RedBox In this chapter we use the web console interface to introduce the functions 2 Getting Started In this chapter we explain how to install a Moxa PRP HSR RedBox for the first time There are three ways to access the Moxa PRP HSR RedBox s configuration settings USB console command line interface or web based interface If you do not know the Moxa PRP HSR RedBox s IP address you can open the USB console by connecting the Moxa PRP HSR RedBox to a PC s USB port with a USB cable You can open the Telnet or web based console over an Ethernet LAN or over the Internet The following topics are covered in this chapter O USB Console Configuration 115200 None 8 1 VT100 O Configuration by Command Line Interface CLI O Configuration by Web Browser PRP HSR Redundancy Box Getting Started USB Console Configuration 115200 None 8 1 VT100 NOTE e You cannot connect to the USB console and command line interface at the same time e You can connect to the web console and another console serial or Telnet at the same time However we strongly recommend that you do NOT do so Following this advice will allow you to maintain better control over the Moxa PRP HSR RedBox s configuration NOTE We recommend using PComm Terminal Emulator when opening the USB console This software can be downloaded free of charge from the Moxa website Before running PComm Terminal Emulator i
26. e opposing device shuts down Four response actions are available when events are triggered Action Description OOOO Trap The PT G503 PHR PTP series will send notification to the trap server when an event is E Mail The PT G503 PHR PTP series will send notification to the email server defined in the Email Syslog The PT G503 PHR PTP series will record a syslog to syslog server defined in Syslog Server O PA Relay The PT G503 PHR PTP series supports digital inputs to integrate sensors When an event is Pe triggered the device will automate alarms by relay output Severity Emergency System is unusable Alert Action must be taken immediately Critical Critical conditions Error Error conditions Warning Warning conditions Notice Normal but significant condition Information Informational messages Debug Debug level messages Email Settings Email Setup Mail Server TCP Part 25 UserName Password 1st Recipient Email Address 2nd Recipient Email Address ard Recipient Email Address 4th Recipient Email Address Mail Server IP Name IP address The IP Address of your email server 3 10 PRP HSR Redundancy Box Featured Functions NOTE User Name Password Setting Factory Default Password The email account password None Email Address Max of 30 characters You can set up to 4 email addresses to receive alarm emails None from the Moxa PRP HSR RedBox Send Test Email After you complete the email set
27. ents will be recorded into the Moxa PRP HSR RedBox s Event Log Table e Cold start e Warm start e Configuration change activated e Power 1 2 transition Off On Power 1 2 transition On Off e Auth Success e Auth Fail e Auth Attempts Over Limit e Password Change e ABC 02 status e LLDP Table Change 3 32 PRP HSR Redundancy Box Featured Functions System Services This page shows the services summary running on the RedBox device System Services SSH IPv4 TCP 22 SSH IPv6 TCP 29 Telnet IPv4 TCP 23 Telnet IPv6 TCP 23 Web Server Http IPv4 TCP 80 Web Server Http IPv6 TCP 80 MMS IPv4 TCP 102 NTP SNTP IPv4 UDP 123 NTP SNTP IPv4 UDP 123 SNMF Agent IPv4 UDP 161 Web Server Https IPv4 TCP 443 DNS Client IPv4 UDP 949 Moxa Utility Service IPv4 TCP 4000 Moxa Utility Service IPv4 UDP 4000 3 33 A MIB Groups The Moxa PRP HSR RedBox comes with built in SNMP Simple Network Management Protocol agent software that supports cold warm start trap line up down trap and RFC 1213 MIB II The standard MIB groups that the Moxa PRP HSR RedBox supports are as follows MIB II 1 System Group sysORTable MIB 11 2 Interfaces Group ifTable MIB 11 4 IP Group ipAddrTable ipNetToMediaTable IpGroup IpBasicStatsGroup IpStatsGroup MIB II 5 ICMP Group IcmpGroup IcmpInputStatus IcmpOutputStats MIB II 6 TCP Group tcpConnTable TcpGroup TcpStats MIB II 7 UDP Group udpTable UdpStats MIB II 10 Tra
28. h easier to troubleshoot optical fiber links and virtually eliminates the cost of onsite debugging at remote sites SFP Digital Diagnostic Monitor G2 SFP 1GLXLC T 31 5 3 3 75 29 7 G3 SFP 1GLXLC T 30 6 33 bf 35 4 PRP HSR RedBox port number with SFP plugged in Model Name Moxa SFP model name NOTE Certain tolerances exist between real data and measured data eee Tx power dBm Rx power dBm 3 31 PRP HSR Redundancy Box Featured Functions Event Log Event Log Page 48 48 Bootup System 706 125 0d2h52m41s5 Port 2 link on TOT 125 0d3h0ma49s 192 168 127 66 admin Auth ok 708 125 0d3h6ma4s 192 168 127 66 admin Auth ok 709 125 0d3h11m56s Port 7 link on 710 125 0d3h12m14s Port 7 link off 711 125 0d3h12m16s Port 7 link on T12 125 0d3h12m18s Port 7 link off ma 125 0d3h12m19s Port 7 link on 714 125 0d3hn30m39s 192 168 127 66 admin Auth ok The Event Log Table displays the following information Index Event index assigned to identify the event sequence Bootup Number This field shows how many times the Moxa PRP HSR RedBox has been rebooted or cold started The date is updated based on how the current date is set on the Basic Settings page The time is updated based on how the current time is set on the Basic Settings page System Startup The system startup time related to this event Time Events that have occurred NOTE The following ev
29. hernet console port is used to monitor the activity of the monitored port Monitoring You can monitor statistics in real time from the Moxa PRP HSR RedBox s DSL extender s web console and USB console CPU Memory Utilization The CPU Memory Utilization page displays how much system resources are being utilized Monitor this information to get a quick snapshot of the PRP HSR RedBox s current status CPU Memory Utilization CPU Utilization J 0 Past 5secs Free Memory 17081500 Bytes Power Consumption 4 33 Watts CPU Utilization Read only CPU usage volume in the past 5 seconds 30 seconds or 5 minutes Free Memory Read only Amount of free memory currently available Power Consumption Read only Amount of power currently being consumed by the PRP HSR _ None RedBox 7 unit watts 3 27 PRP HSR Redundancy Box Featured Functions 3 28 PRP HSR Redundancy Box Featured Functions Statistics Access the Monitor by selecting Monitoring from the left selection bar Monitor by System allows the user to view a graph that shows the combined data transmission activity of all of the Moxa PRP HSR RedBox s 18 ports Click one of the four options Total Packets TX Packets RX Packets or Error Packets to view transmission activity of specific types of packets Recall that TX Packets are packets sent out from the Moxa PRP HSR RedBox RX Packets are packets received from connected devices and Error Packets are pa
30. ing the last 6 digits of the PRP HSR RedBox s MAC address without spaces Click Browse to select the configuration file and then click Restore to start loading the file into your PRP HSR RedBox Auto load configuration from ABC 02 to system when booting up Select the Auto load configuration from ABC to system when boot up checkbox and then click Apply This function is enabled by default First power off your PRP HSR RedBox and then plug in the ABC 02 Next power on your PRP HSR RedBox The system will detect the configuration file on the ABC 02 automatically The PRP HSR RedBox will recognize file names using the following sequencing priority First priority MAC ini Second priority Sys ini If a matching configuration file is not found the fault LED light will turn on and the PRP HSR RedBox will boot up normally Note MAC ini is named using the last 6 digits of the PRP HSR RedBox s MAC address without spaces 3 14 PRP HSR Redundancy Box Featured Functions 5 Auto backup to ABC 02 when configuration changes Select the Auto backup to ABC 02 when configuration changes checkbox and then click Apply This function is disabled by default The ABC 02 can back up PRP HSR RedBox configuration files automatically While the ABC 02 is plugged into the PRP HSR RedBox enable the Auto backup to ABC 02 when configuration change option and then click Apply Once this configuration has been modified the PRP HSR RedBox will back up the
31. nfiguration change activated e Power 1 2 transition Off On Power 1 2 transition On Off e Auth Success e Auth Fail e Auth Attempts Over Limit e Password Change e ABC O2 status e LLDP Table Change Relay Warning Status When a relay warning is triggered by either system or port events the administrator can decide to shut down the hardware warning buzzer by clicking the Apply button The event will still be recorded in the event list Relay Warnning Status E Relay 1 Alarm Cut Off ACO Apply MAC Address Table The MAC address table shows the MAC address list passed through the Moxa PRP HSR RedBox The MAC Address table can be configured to display the following Moxa PRP HSR RedBox MAC address groups which are selected from the drop down list MAC Address Table All Page 1 7 1 ac 81 12 59 44 83 Unicast l Interlink 2 74 d0 2b 97 b4 f3 Unicast l Interlink 3 c d3 a3 94 08 4c Unicast l Interlink 4 00 0a 19 74 12 13 Unicast l Interlink 5 1c ab a7 4d d5 59 Unicast l Interlink 6 3c 97 0e 61 ec 61 Unicast l Interlink T 58 az2 b5 7d 60 05 Unicast l Interlink 8 20 54 76 8e 84 61 Unicast l Interlink g 00 13 ce 54 59 54 Unicast l Interlink 10 00 13 46 05 33 1 Unicast l Interlink Drop Down List ALL Select this item to show all of the Moxa PRP HSR RedBox s MAC addresses ALL Learned Select this item to show all of the Moxa PRP HSR RedBox s Learned MAC addresses PortA si Select this item to show all MAC ad
32. nsmission Group dot3 dot3StatsTable MIB II 11 SNMP Group SnmpBasicGroup SnmpInputStats SnmpOutputStats The Moxa PRP HSR RedBox also provides a private MIB file located in the file Moxa PRP HSR RedBox s model name MIB my on the Moxa PRP HSR RedBox utility CD ROM PRP HSR Redundancy Box Public Traps Cold Start Warm Start Link Up Link Down Authentication Failure Fiber Check Private Traps Configuration Changed Power On Power Off LLDPChgTrap MIB Groups CLI Command Support for the EOM G103 PHR PTP Module Basic Commands command Tee information O Show Commands Commana Pisptay information O O show interfaces hw_interface show redundancy mode Current redundancy protocol mode show mac address table learned interface Display MAC address forwarding table by interface learned show logging event log Display system event logs show vlan filtering Display vlan filtering configuration show multicast filtering Display Multicast Filtering status PRP HSR Redundancy Box CLI Command Support for the EOM G103 PHR PTP Module Configuration Commands hostname lt string token1 gt Set system s network name maximum 35 characters clock set lt STRING time gt hh mm ss Adjust the clock clock timezone gmt lt INT offset_hour gt Time zone hour shifting clock summer time start date lt STRING month gt The date summer time offset daylight savings time starts clock summer time end date
33. nstall the USB console driver on your PC and then connect the Moxa PRP HSR RedBox s USB console port to your PC s COM port generally COM1 or COM2 depending on how your system is set up with USB to DB9 F or RJ45 to DB25 F cable After installing PComm Terminal Emulator open the Moxa PRP HSR RedBox s USB console as follows 1 From the Windows desktop click Start gt All Programs gt PComm Lite Ver1 6 gt PComm Terminal Emulator MG SOFT MIB Browser Microsoft Office Microsoft Silverlight Li Microsoft SQL Server 2005 Li Microsoft Visual Studio 2008 y Microsoft Windows SDK v6 0A MOXA MXstudio Li PComm Lite Ver1 6 EP Library Programming Guide EP Library Reference ES maxterm BY PComm Diagnostic af PComm Monitor PE PComm Terminal Emulator ce Performance Analyzer J UPort Windows Driver di MOXA UPort 1100 Series Windows Di MOXA USB Driver Li Net SNMP Notepad d NPort Search Utility NuDesign Tools Eval di PCIMan an Mm A Back p pen Shut Down F Profile Port Manager Help n Ctrl 4lt 0 e 2 2 PRP HSR Redundancy Box Getting Started 3 The Property window should open On the Communication Parameter tab for Ports select the COM port that is being used for the console connection Set the other fields as follows 115200 for Baud Rate 8 for Data Bits None for Parity and 1 for Stop Bits Communication Parameter Terminal File Transfer Captu
34. ost portion of the Link Local address is automatically generated using the modified EUI 64 form of the interface identifier PRP HSR RedBox s MAC address IPv6 Neighbor Cache The information in the neighbor cache includes the neighboring node s IPv6 address the corresponding Link Layer address and the current state of the entry IPv6 Neighbor Cache Link Layer MAC Address fes0 290 e8ffe02 406 00 90 e8 02 04 06 Reachable Date and Time The Moxa PRP HSR RedBox has a time calibration function based on information from an NTP server or user specified time and date allowing functions such as automatic warning emails to include a time and date stamp NOTE The Moxa PRP HSR RedBox does not have a real time clock The user must update the Current Time and Current Date to set the initial time for the Moxa PRP HSR RedBox after each reboot especially when there is no NTP server on the LAN or Internet connection 3 6 PRP HSR Redundancy Box Featured Functions system Time System Up Time 0d1h59m50s Current Time 2013 06 19 15 43 49 Clock Source Local NTP SNTP Time Settings 2 Manual Time Settings Date YY MM DD 2013 1 06 19 Time HH MM SS 15 43 49 Sync from Local Device Time 2013 6 19 15 43 56 Enable NTPSNTP Server Time one GMT Greenwich Mean Time Dublin Edinburgh Lisbon London bl Daylight Saving Month Week Day Hour Start Date T e 2 F End Date r z F Offset hr
35. ox When the accessible IP list is enabled only addresses on the list will be allowed access to the Moxa PRP HSR RedBox Each IP address and netmask entry can be tailored for different situations e Grant access to one host with a specific IP address For example enter IP address 192 168 1 1 with netmask 255 255 255 255 to allow access to 192 168 1 1 only e Grant access to any host on a specific subnetwork For example enter IP address 192 168 1 0 with netmask 255 255 255 0 to allow access to all IPs on the subnet defined by this IP address subnet mask combination e Grant access to all hosts Make sure the accessible IP list is not enabled Remove the checkmark from Enable the accessible IP list The following table shows additional configuration examples Hosts That Need Access Input Format 192 168 1 120 255 255 255 255 3 21 PRP HSR Redundancy Box Featured Functions Authentication Certificate Authentication Certificate SSL Certificate Re generate SSH Key Re generate Note Few minutes may be required Web will be unavailable temporarily until it finish Apply SSL Certificate Re generate Select Deselect Enable SSL Certificate Re generation SSH Key Re generate Factory Default Select Deselect Enable SSH Key Re generation SNMP The Moxa PRP HSR RedBox supports SNMP V1 V2c and V3 SNMP V1 and SNMP V2c use a community string match for authentication which means that SNMP servers access all objects with read
36. pport Contact Information Moxa Americas Toll free 1 888 669 2872 Tel 1 714 528 6777 Fax 1 714 528 6778 Moxa Europe Tel 49 89 3 70 03 99 0 Fax 49 89 3 70 03 99 99 Moxa India Tel 91 80 4172 9088 Fax 91 80 4132 1045 www moxa com su ort Moxa China Shanghai office Toll free 800 820 5036 Tel 86 21 5258 9955 Fax 86 21 5258 5505 Moxa Asia Pacific Tel 886 2 8919 1230 Fax 886 2 8919 1231 Table of Contents i o A Pe aa a a eae 1 1 2 Getting Se ceca veneiie detec ese ewes ereiins evade ved eveiws ewe vedeweWs vase vereewwededeliewsveveueWesesuseseswwesedesiewedeverenedeeus 2 1 USB Console Configuration 115200 None 8 1 VT100 ccc cccccee eee eee e ee rr rr 2 2 Configuration by Command Line Interface CLI 0c ccc ceee een eee eee eens eens nn eeeeeeeeneaeeeeeenaseneeetnnseenenenns 2 3 Configuration DY WED BroWser ientnrsyzeronsscnedrpronareseraravereronesanaronniounroseranarereronns aver IPPO Dro orto rin 2 5 3 e a FUNCIONS sissa a S aa aaa duces 3 1 POE ll das 3 2 SAELE SUI MMM E Mt AAE A T E E ED Ae 3 2 System IONN A O inerea EEEE E EEE EE 3 2 USEF ACCOUNT oiro ore E E E E E E E E E E E E E E E EE E E amen aR a 3 3 Nr Cee ner re e eer e 3 5 Dee tal WS A o aaa 3 6 Wanna Not Ca colecta todas dede wee tute ope dc eee tate tee ene uae eee e ete eee ete ene tues den ete ete seen saeeee ss 3 8 MASAS Ti nce et cere 3 12 SUSI eS A oe a ER RR A el EREE EEE E RE etree EEEE TE ETE AR 3 13
37. ring COM Options Ports Baud Rate Data Bits Parity Stop Bits Output State DTA ON OFF Flow Control M ATS CTS RDN lt 0FF RTS ON OFF 4 On the Terminal tab select VT100 for Terminal Type and then click OK to continue Communication Parameter Terminal File Transfer Capturing Terminal Type 47100 Dumb Terminal Option Transmit M local Echo Send Enter kep Az Receive CR Translation No Changed LF Translation No Changed cos Configuration by Command Line Interface CLI Opening the Moxa PRP HSR RedBox s Telnet or web console over a network requires that the PC host and Moxa PRP HSR RedBox are on the same logical subnet You may need to adjust your PC host s IP address and subnet mask By default the Moxa PRP HSR RedBox s IP address is 192 168 127 253 and the Moxa PRP HSR RedBox s subnet mask is 255 255 255 0 referred to as a Class B network Your PC s IP address must be set to 192 168 xxx xxx if the subnet mask is 255 255 0 0 or to 192 168 127 xxx if the subnet mask is 255 255 255 0 NOTE To connect to the Moxa PRP HSR RedBox s Telnet or web console your PC host and the Moxa PRP HSR RedBox must be on the same logical subnet 2 3 PRP HSR Redundancy Box NOTE NOTE Getting Started When connecting to the Moxa PRP HSR RedBox s Telnet or web console first connect one of the Moxa PRP HSR RedBox s Ethernet ports to yo
38. s Disabled Warning Notification Since industrial Ethernet devices are often located at the endpoints of a system these devices will not always know what is happening elsewhere on the network This means that an PRP HSR RedBox that connects to these devices must provide system maintainers with real time alarm messages Even when control engineers are out of the control room for an extended period of time they can still be informed of the status of devices almost instantaneously when exceptions occur The Moxa PRP HSR RedBox supports different approaches to warn engineers automatically such as email trap syslog and relay output It also supports two digital inputs to integrate sensors into your system to automate alarms by email and relay output System Event Settings System Events are related to the overall function of the PRP HSR RedBox Each event can be activated independently with different warning approaches Administrator also can decide the severity of each system event system Event Settings Action Trap E Mail Sys log Relay Cold Start El El a Critical S Warm Start a a A Waming Config Changed F F El Warning 111 PWR 1 Off On E E E Warning E PWR 2 Off gt On A A E Warming PWR 1 On Off A A E E Warning PWR 2 On 0ff F F El F Warning F Auth Fail A TA F Waming Password Changed E Warning Apply 3 8 PRP HSR Redundancy Box Featured Functions System Even
39. server as None the authentication database ha Set the communication port of an external TACACS RADIUS TACACS 49 Authentication mechanism selection ASCII PAP CHAP and ASCII for TACACS scuba rinse and OOS CAO The timeout period to wait for a server response TACACS 30 RADIUS 5 3 19 PRP HSR Redundancy Box Featured Functions Management Interface Management Interface v Enable HTTP Pot 80 Yi Enable SSL Port 1443 v Enable Telnet Pot 23 v Enable SSH Port 22 mn Web Auto Logout min Enable HTTP Select Deselect Checkmark the appropriate check boxes to enable HTTP Select Port 80 Enable SSL Select Deselect Checkmark the appropriate check boxes to enable SSL Select Port 443 Enable Telnet Select Deselect Checkmark the appropriate check boxes to enable Telnet Select Port 23 Enable SSH Select Deselect Checkmark the appropriate check boxes to enable SSH Port 5 Web Auto Logout min 3 20 PRP HSR Redundancy Box Featured Functions Trusted Access The Moxa PRP HSR RedBox uses an IP address based filtering method to control access Trusted Access Enable trusted access Please add your local IP address first otherwise your PC will not be able to connect the device again Mau IP Address Subnet Mask 32 253 253 253 255 Es COR EJ El El El El El El El 32 233 255 253 255 F You may add or remove IP addresses to limit access to the Moxa PRP HSR RedB
40. t cable The Moxa PRP HSR RedBox s default IP address is 192 168 127 253 After making sure that the Moxa PRP HSR RedBox is connected to the same LAN and logical subnet as your PC open the Moxa PRP HSR RedBox s web console as follows 1 Connect your web browser to the Moxa PRP HSR RedBox s IP address by entering it in the Address or URL field 3 washingtonpost com News Front Microsoft Internet Explorer Q Search 9 A Bact Forvard Stop Refresh Home File Edit View Favorites Tools Help Address 192 169 127 253 y Go 2 The Moxa PRP HSR RedBox s web console will open and you will be prompted to log in Select the login account admin or user and enter the Password This password will be required to access any of the consoles web serial Telnet 2 5 PRP HSR Redundancy Box Getting Started MOXN Moxa Industrial Device PT G503 Username Password i Login goahead WEBSERVER NOTE By default the password assigned to the Moxa PRP HSR RedBox is moxa Be Sure to change the default password after your first log in to maintain a higher level of security 3 After logging in you may need to wait a few moments for the web console to appear Use the folders in the left navigation panel to navigate between different pages of configuration options MOXA PowerTrans PT G503 Series www moxa com Model PT G503 IP 172 21 0 164 MAC Address 00 90 E8 05 03 40 PWR1 P
41. the minimum requirement for authentication SHA Authentication will be based on the HMAC SHA algorithms No Auth 8 character passwords are the minimum requirement for 3 23 PRP HSR Redundancy Box Featured Functions Enable Admin Data Encryption Key for SNMP V1 V2c V3 and V3 only Setting Description Factory Default Enable Enables data encryption using the specified data encryption key No between 8 and 30 characters Specifies that data will not be encrypted User Auth Type for SNMP V1 V2c V3 and V3 only No Auth Allows the admin account and user account to access objects No without authentication MD5 Auth Authentication will be based on the HMAC MD5 algorithms No 8 character passwords are the minimum requirement for authentication SHA Auth Authentication will be based on the HMAC SHA algorithms No 8 character passwords are the minimum requirement for authentication Enable User Data Encryption Key for SNMP V1 V2c V3 and V3 only Enable Enables data encryption using the specified data encryption key No between 8 and 30 characters No data encryption Trap Settings SNMP traps allow an SNMP agent to notify the NMS of a significant event The PRP HSR RedBox supports two SNMP modes Trap mode and Inform mode Trap inform Recipient Trap Mode Trap V1 Host IP Address 1 1st Trap Community public Host IP Address 2 2nd Trap Community public SNMP Trap Mode Trap In Trap mo
42. tings you should first click Apply to activate those settings and then press the Test button to verify that the settings are correct Auto warning email messages will be sent through an authentication protected SMTP server that supports the CRAM MD5 LOGIN and PAIN methods of SASL Simple Authentication and Security Layer authentication mechanism We strongly recommend not entering your Account Name and Account Password if auto warning email messages can be delivered without using an authentication mechanism Syslog Server Settings The Syslog function provides the event logs for the syslog server The function supports 3 configurable syslog servers and syslog server UDP port numbers When an event occurs the event will be sent as a syslog UDP packet to the specified syslog servers Each Syslog server can be activated separately by selecting the check box and enabling it syslog Settings syslog 1 Server UDP Port 514 1 65535 syslog 2 Server UDP Port 514 1 65535 syslog 3 Sever UDP Port 514 1 65535 Apply Syslog Server 1 2 3 IP Address Enter the IP address of Syslog server 1 2 3 used by your None network Port Destination Enter the UDP port of Syslog server 1 2 3 514 1 to 65535 3 11 PRP HSR Redundancy Box Featured Functions NOTE The following events will be recorded into the Moxa PRP HSR RedBox s Event Log table and will then be sent to the specified Syslog Server e Cold start e Warm start e Co
43. ts Cold Start Warm Start The Moxa PRP HSR RedBox is rebooted such as when network parameters Configuration Change PWR1 Off gt On PWR1 On gt 30ff Auth Success Auth Fail Auth Attempts Over Limit Password Change DI1 On gt Off DI1 Off gt On ABC 02 Status Occurs when an ABC 02 USB T was connected to or disconnected from the PRP HSR RedBox or when the ABC 02 USB T automatically imported exported or backed up a configuration LLDP Table Change The LLDP table has been changed to account for recently connected devices Port Event Settings Port Events are related to the activity of a specific port Port Event Settings Fiber Check es e dol m a a e T a E Severity ds On Off behets sata ia Temperature Trap Syslog Relay1 a a malo a a Co jajaa al Wann alo m a a a a a mle a ele m a wam alal Warning 7 5 Encose a a a 8 a a ajaa a wam gt Fiber Check Alarm Threshold E SFP LX SFP 1GLXLC 1000BASE LX 10 0 a25 2 SFP SX SFP 1GSXLC T 1000BASE SX SFP LHX SFP 1GLHXLC 1000BASE LX 24 o SFP ZX SFP IGZXLC 1000BASE xX_ 120 8 SFP EZX 120 SFP 1GEZXLC 120 1000BASEHIX 120 6 oo SFP ZX SFP 1GZXLC T 1000BASEIX 120 8 SFP 1FESLC T 3 9 PRP HSR Redundancy Box Featured Functions Port Events Warning email is sent when Link ON The port is connected to another device Link OFF The port is disconnected e g the cable is pulled out or th
44. ur Ethernet LAN or directly to your PC s Ethernet port You may use either a straight through or cross over Ethernet cable The Moxa PRP HSR RedBox s default IP address is 192 168 127 253 After making sure that the Moxa PRP HSR RedBox is connected to the same LAN and logical subnet as your PC open the Moxa PRP HSR RedBox s Telnet console as follows 1 Click Start gt Run from the Windows Start menu and then Telnet to the Moxa PRP HSR RedBox s IP address from the Windows Run window You may also issue the Telnet command from a DOS prompt Run H ES Type the name of a program folder document or Internet 3 resource and Windows will oper it for you Oper telnet 192 168 127 253 Cancel Browse 2 In the terminal window type user name and password and then press Enter E COM18 115200 None 8 1 VT100 bo la kE m login as admin a ora password nts State OPEN ee ee 2 Ready TX 142 Rx 9193 EY COM18 115200 None 8 1 VT100 com en E orn a PT G5 3 show interfaces mgmt IPv4 IP configuration IP address Subnet mask Default gateway DNS server Static 192 168 127 252 yom OF de me be 0 0 0 0 IPv6 Global Unicast Address Prefix Global Unicast Address nos Link Local Address fe80 290 e8ff fe05 339 State OPEN Se ae me Ready Tx 127 Rx 9147 2 4 PRP HSR Redundancy Box NOTE Getting Started COMS 115200 None 8 1 VT100 Laa m EOM G1 3 series V4 build
45. uth Type No Auth Enable Admin Data Encryption Data Encryption Key User Auth Type No Auth Enable User Data Encryption Data Encryption Key Community V1 V2c Read Community public V1 V2c Write Read Community private Trap inform Recipient Trap Mode Trap v1 Host IP Address 1 ist Trap Community public Host IP Address 2 2nd Trap Community public SNMP Read Write Settings SNMP Versions V1 V2c V3 or Specifies the SNMP protocol version used to manage the V1 V2c V1 V2c or PRP HSR RedBox V3 only V1 V2c Read Community Max 30 characters Specifies the community string to authenticate the SNMP agent Public for read only access The SNMP agent will access all objects with read only permissions using this community string V1 V2c Write Read Community Max 30 characters Specifies the community string to authenticate the SNMP agent Private for read write access The SNMP server will access all objects with read write permissions using this community string For SNMP V3 two levels of privilege are available to access the Moxa PRP HSR RedBox Admin privilege provides access and authorization to read and write the MIB file User privilege allows reading of the MIB file only Admin Auth Type for SNMP V1 V2c V3 and V3 only No Auth Allows the admin account to access objects without No authentication MD5 Authentication will be based on the HMAC MD5 algorithms Auth 8 character passwords are
46. vice Description Max 30 characters This option is useful for recording a more detailed description of PRP HSR RedBox the unit Model name Contact Information Max 30 characters This option is useful for providing information about who is responsible for maintaining this unit and how to contact this person User Account The Moxa PRP HSR RedBox supports the management of accounts including establishing activating modifying disabling and removing accounts There are two levels of configuration access admin and user Accounts with admin authority have read write access to all configuration parameters whereas accounts with user authority only have read access to configuration parameters NOTE 1 In order to maintain a higher level of security be sure to change the default password after your first log in 2 The user with admin account name cannot be deleted or disabled User Account Active 52 Authority admin User Name Password Confirm Password Account List pon admin admin user user Delete Active Checked The Moxa PRP HSR RedBox can be accessed by the activated Enabled Unchecked The Moxa PRP HSR RedBox can t be accessed by the ON ee Sid Authority admin The account has read write access of all configuration admin parameters user The account can only read configuration but without any modification 3 3 PRP HSR Redundancy Box Featured Functions Creating a New Ac
47. vity that can be viewed with the Console Monitor function discussed above The All Ports option shows three vertical bars for each port The height of the bar represents Packets s for the type of packet at the instant the bar is being viewed That is as time progresses the height of the bar moves up or down so that the user can view the change in the rate of packet transmission The blue colored bar shows Uni cast packets the red colored bar shows Multi cast packets and the orange colored bar shows Broad cast packets The graph is updated every few seconds allowing the user to analyze data transmission activity in real time Statistics Port 2 Total Packets Packetisec 30 168 336 504 Ay Unicast Multicast Broadcast sec alias Lh Total Packets Packets in past 5 secs Update Interval every 5 secs Tx Collision 16745 1585 13910 14 2815 1 20 0 0 0 246486420 18055 20 801 0 5992 0 0 0 Tx CRC Error 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 30 PRP HSR Redundancy Box Featured Functions Fiber Check Optical fiber is commonly used for long distance data transmission However when link issues occur it is very costly to troubleshoot fiber cables and fiber transceivers at remote sites To solve this problem the Moxa PRP HSR RedBox provides digital diagnostics and monitoring functions on the Moxa SFP optical fiber links that allow users to measure optical parameters and performance from the central site This function makes it muc
Download Pdf Manuals
Related Search