KTD-411
Contents
1. Current Database Data MatrixSwitcherD ata mdb Figure 2 Matrix Switcher Programmer main dialog box Note If the desktop icon is unavailable click Start on the task bar point to Programs Kalatel Matrix Switcher and then click KTD 411 Programming Software 2 Click System Setup The System Setup System Setup x dialog box appears See Figure 3 Chassis Size 4nd Setup Highest Camera Address Number Of Monitors 3 Type the highest camera address and the number of monitors in your system 4 Click Done Figure 3 Enter the system information 1036512C September 2003 7 Camera Setup KTD 411 Programming Software User Manual 3 CAMERA SETUP 1 On the K Matrix Switcher Programmer dialog box Figure 2 click Camera Setup The Camera Setup dialog box Figure 4 appears 2 Click the BNC Number of the camera you want to set up Camera Setup x Edit Camera s setup directly BNC Num Camera Title a 000 000 Kalatel None 001 001 None None None None None None None None None None None None None None None vi Clear Selection Note Click in camera number field to select rows Clear All Save Camera Setup Figure 4 Camera Setup dialog box 3 Type the number of the BNC connector on the back of the chassis to which the camera will be connected See Figure 5 Note Remote switcher BNC mapping is not supported 4 Inthe Camera Title field type a camera titl2. DATABASE 21 FAR SAVE ee le 21 Phe Open TTS ETTE 21 7 2 OPENING NEW DATABASE eee 22 KTD 411 Programming Software User Manual Table of Contents BEFORE You BEGIN Read these instructions before installing or operating this product Note This installation should be made by a qualified service person and should conform to local codes This manual provides installation and operation information To use this document you must have the following minimum qualifications e A basic knowledge of CCTV systems and components e A basic knowledge of electrical wiring and low voltage electrical hookups Use this product only for the purpose for which it was designed Customer Support For assistance in installing operating maintaining and troubleshooting this product refer to this document and any other documentation provided If you still have questions contact Technical Support GE Interlogix Video Systems Group Call 800 469 1676 Fax 541 752 9096 Note You should be at the equipment ready with details before calling Technical Support Conventions Used in this Manual Boldface or button icons highlight command entries The following WARNING CAUTION and Note statements identify potential hazards WARNING A Improper use of this equipment can cause severe bodily injury or equipment damage CAUTION Improper use of this equipment can cause equipment damage Note Notes contain import
3. call 800 469 1676 Technical support is available 24 hours a day 7 days a week Call Tech Support 800 469 1676 6 A M 5 P M PST Monday through Friday Tech Support 541 740 3589 all other times Main 800 343 3358 or 541 754 9133 Fax Tech Support 541 752 9096 available 24 hours a day Main 541 754 7162 Web www GE Interlogix com 1036512C September 2003 TABLE OF CONTENTS BEFORE YOU BEGIN ssssceeceesssseeeeeseseeeeeesesseeeeeeseseeeeeeneeees 5 1 SOFTWARE INSTALLATION nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnennn 6 1 1 MAKING CONNECTIONS ccccsssssceesssssseeeeessseseees 6 2 SYSTEM SETUR skue 7 3 GAMERA SETUP uses E KA Be RAE RA ka 8 4 PROGRAMMING MONITORS ccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 10 4 1 MONITOR SETUP aaret dened kk K k k k k 11 4 2 ARMING CAMERAS cccccceceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeess 12 4 3 MONITORS SEQUENCE SETUP cccceeeeeeeeeeeeeeeeees 13 4 3 1 Sequences 1 G mmnnnrnnrnrrnannrnnnnnvnnrrrennnrrennrnnsnnvnnenren 13 4 3 2 sSOQUENCE Tunnansamnnskie Kenan 15 5 GROUPS ene 16 5 1 GROUP SETUP vudskadeskRdesadedkdaaadaaddt 16 5 2 GROUP SEQUENCE SETUP rmnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnne 17 6 DOWNLOADING AND UPLOADING nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 19 6 1 DOWNLOADING HE 19 6 2 UPLOADING kk kk k K k KK KA kK K 20 7 OPENING AND SAVING A DATABASE ccccceeeeeeeeeeeeeeeeeeees 21 7 1 OPENING AND SAVING AN EXISTING
4. User Manual KTD 411 Digiplex IV Programming Software TIT GE interlogix GE Interlogix Kalatel 2003 GE Interlogix Video Systems Group All Rights Reserved Any GE Interlogix Video Systems Group software supplied with GE Interlogix Video Systems Group products is proprietary and furnished under license and can be used or copied only in accordance with the terms of such license This document contains proprietary information that is protected by copyright No part of this document may be reproduced or transmitted in any form or by any means without the prior written permission of GE Interlogix Video Systems Group The information contained in this document is subject to change without notice GE Interlogix Video Systems Group in keeping pace with technological advances is a company of product innovation Therefore it is difficult to ensure that all information provided is entirely accurate and up to date GE Interlogix Video Systems Group accepts no responsibility for inaccuracies or omissions and specifically disclaims any liabilities losses or risks personal or otherwise incurred as a consequence directly or indirectly of the use or application of any of the contents of this document For the latest product specifications visit GE Interlogix Video Systems Group online at www GE Interlogix com or contact your Kalatel sales representative For technical support before and after installation
5. ant information about a product or procedure This symbol indicates electrical warnings and cautions This symbol indicates general warnings and cautions 1036512C September 2003 5 Before You Begin KTD 411 Programming Software User Manual 1 1 2 3 4 1 1 SOFTWARE NSTALLATION Insert the programming software CD into your computer s CD ROM drive If the installer does not open automatically select the CD drive in Windows Explorer Click Install Matrix Switcher Programmer The Matrix Switcher Programmer Installer opens Follow the on screen instructions MAKING CONNECTIONS See Figure 1 and perform the following 1 2 3 Connect the supplied cable to the DB9 adapter Connect the DB9 adapter to your computer s COM port Connect the cable to the RS232 port on the back of the KTD 440 or on the front of the KTD 447 card DB9 KTD 440 connector COM port Cable to Figure 1 Connecting the switcher to your computer 10365120 September 2003 KTD 411 Programming Software User Manual Software Installation 2 SYSTEM SETUP 1 To open the software double click the KTD 411 Programming Software desktop icon The K Matrix Switcher Programmer dialog box appears See Figure 2 K Matrix Switcher Programmer h ha oj xj File Download Upload System Setup Help m Monitor Programming ajaleluleluujn alulaalala a ulalalulaat Slalalssja
6. at Alarm Dwell 2 v IT Decimal Date Deliminator o Figure 7 Monitor Setup tab 10365120 September 2003 11 Programming Monitors KTD 411 Programming Software User Manual 4 2 ARMING CAMERAS See Figure 8 and perform the following Programming Monitor 3 000 Figure 8 Arming Cameras tab 1 Click the Arming Cameras tab in the Programming Monitor dialog box 2 All cameras are armed by default e To disarm one camera click the camera number then click Disarm e To disarm multiple cameras simultaneously press the Ctrl key and click each camera number then click Disarm e To disarm all cameras click Disarm All 12 1036512C September 2003 KTD 411 Programming Software User Manual Programming Monitors 3 4 3 4 3 1 Click Save Armed Cameras Note If you click Close or another tab in the Programming Monitor dialog box without saving changes a warning dialog box appears Settings will be lost if you do not save them MONITORS SEQUENCE SETUP SEQUENCES 1 6 Each monitor or group of monitors can use one of six sequences 1 through 6 with up to 32 steps each To set up a Sequence of camera views for the selected monitor s see Figure 9 and perform the following 1 2 3 4 5 6 Click the Monitors Sequence Setup tab of the Programming Monitor dialog box Armed cameras are displayed in the box on the left Select the desire
7. d Sequence Number Click on the camera to appear first in the sequence The camera will display as active In the Sequence Step Dwell Time drop down menu select how many seconds 1 30 the camera is to remain on the monitor Click Add To Sequence The camera number and its dwell time appear in the box on the right Repeat steps 3 through 5 until you enter all desired cameras in the sequence 1036512C September 2003 13 Programming Monitors KTD 411 Programming Software User Manual Programming Multiple Monitors x Monitor Setup Arming Cameras Monitors Sequence Setup Sequence Number Ko BB BB BUN AR OR 1 2 3 4 5 6 7 Camera Name Step Camera Dwell Time O00 Kalatel 001 DigiPlex Add To Sequence Delete From 009 Shannon Sequence 010 vi E r Universal Dwell Time Sequence Step Dwell Time 2 ba Saved Dwell Time 2 Cameras will be inserted above the selected items in the sequence list If no steps are selected cameras will be added to end Save Sequence Close Figure 9 Monitors Sequence Setup tab for sequences 1 6 e To add a camera in the middle of a sequence position the pointer over the step you wish to change and click it Follow steps 3 through 5 The new camera will be added and all cameras below it will move down one step e To remove a camera from the sequence position the pointer over the step and click it Click Delete From Sequence 7 Click Sa
8. e 5 Inthe Video Loss field click None A drop down arrow appears in the field 8 1036512C September 2003 KTD 411 Programming Software User Manual Camera Setup MONITOR OUTPUTS VIDEO INP 6 m Figure 5 BNC video input connector numbers 6 Click the arrow to select None Sync Low Medium or High sensitivity 7 Repeat steps 2 through 6 for all cameras in the system To clear camera setup information e One camera click the camera number to highlight the row then click Clear Selection e A group of cameras simultaneously press the Ctrl key and click on the number fields of the cameras you would like to clear then click Clear Selection e All cameras click Clear All 8 Click Save Camera Setup 9 Click Close 1036512C September 2003 9 Programming Monitors KTD 411 Programming Software User Manual 4 PROGRAMMING MONITORS Note If any of your monitor numbers are unavailable adjust the number of monitors you typed in section 2 System Setup See Figure 3 e f you want all monitors to share the same settings click Select All Monitors All monitor icons will display as active The Select All Monitors button will change to Deselect All See Figure 6 Note Click Deselect All if you want to deselect all monitors e f you want one or multiple monitors to have different settings click on the number of each monitor T
9. he selected monitor icons will appear as active Note You must click the monitor number not the area above the number Click Monitor s Setup to begin programming the selected monitor s The Programming Monitor dialog box appears K Matrix Switcher Programmer JO x File Download Upload System Setup Help Select All Monitors Monitor s Setup m Monitor Programming Current Database Switcher Groups Cameras Data MatrixS witcherD ata mdb Group Camera Setup Setup Disconnected num Figure 6 Monitor Programming dialog box showing 43 available monitors 10 1036512C September 2003 KTD 411 Programming Software User Manual Programming Monitors 4 1 MONITOR SETUP See Figure 7 and perform the following 1 On the Programming Monitor dialog box click the Monitor Setup tab 2 Set the monitor parameters Note The Universal Dwell time is for monitor and group sequences 3 Click Save Mon Setup Note If you click Close or another tab in the Programming Monitor dialog box without saving changes a warning dialog box appears Settings will be lost if you do not save them Programming Monitor 19 3 x Monitor Setup Arming Cameras Monitors Sequence Setup r Monitor Text Display Position Site Number v Title Position fo v Title Display Yes v r Time and Date Dwell Time Seconds Pasition No Display v Universal Dwell 2 I DDMMYY Date Format gi I 2 Line Form
10. meras C MatrixS witcher Newimproved mdb Com 10 Group Camera Setup Setup NUM Figure 13 Download Upload menu choices 1 Click Download Upload in the main programming dialog box 2 Onthe Select Serial Port submenu select the COM port on your computer to which the switcher is connected 3 Click Connect To Serial Port to connect to the switcher 4 The Connected to Switcher dialog box appears 5 Click OK Note If the No Switcher Card Found warning appears ensure that the switcher is turned on and that all connections are sound 6 Onthe Download Upload menu click Transfer Data 7 Select the appropriate check boxes See Figure 14 Note The Download Upload Sequences check box remains unavailable until the Download Upload Monitors check box is selected 1036512C September 2003 19 Downloading and Uploading KTD 411 Programming Software User Manual Download UpLoad Switcher Data Ez ors Monitors From Number fi To 2 Fi Download plead Sequences I Download U pload Group Data T Download U pload Cameras Camera From Number j To 2 Download To Switcher Upload tio Computer Close Figure 14 Download Upload Switcher Data dialog box Note Monitors group data and cameras can be uploaded or downloaded separately The download or upload process will take longer if all check boxes are selected 8 Click Download to Switcher Note The downloading proces
11. name box Click Open OPENING NEW DATABASE CAUTION Any open unsaved databases will be erased when a new one is created 1 To save the current database see section 7 1 1 Save 2 On the File menu click New Factory Defaults to open a new database The warning in Figure 17 appears 3 To save the current database click No See section 7 1 1 Current databse will be erased to defaults Save Proceed 4 Tocreate anew ve No database click Yes Hur an TEn Figure 17 Save current database warning 22 1036512C September 2003 KTD 411 Programming Software User Manual Printing 8 PRINTING The parameters for any number of cameras monitors monitor sequences or group sequences can be printed 1 On the File menu click Print The dialog box in Figure 18 appears From fi To 54 Cameras From ji To 511 Monitor fn fe ee Group E T Este Print Exit Figure 18 Print dialog box Es 2 Click on the appropriate buttons and type the numbers of the monitors cameras monitor sequences and group sequences whose parameters you wish to print 3 Click Print 4 Click Exit The main programming window appears 10365120 September 2003 23 Troublingshooting KTD 411 Programming Software User Manual 24 1036512C September 2003
12. nce Setup tab 10365120 September 2003 Groups KTD 411 Programming Software User Manual 1 Click the Group Sequence Setup tab 2 Select a sequence number 3 Inthe Sequence Step Dwell Time drop down type or select a dwell time 1 30 for the first group in the sequence 4 Click in the Group Number field for Step 1 and type the number of the group to appear first in the sequence 5 Press Enter or click in the next Group Number field The group name that you programmed in Group Setup appears Note If you enter a group number for a group that has not been set up the default name and Dwell Time appear 6 To change the group in a given sequence step click in the Group Number field of the step you want to change delete the current information and type the new group number 7 To delete a group click the Step number to activate the row and press Delete 8 Click Save Sequence 9 Repeat steps 2 through 7 for successive sequences 10 Click Close 18 10365120 September 2003 KTD 411 Programming Software User Manual Downloading and Uploading 6 6 1 DOWNLOADING AND UPLOADING DOWNLOADING See Figure 13 and perform the following K Matrix Switcher Programmer File Download Upload System Setup Help Connect To Serial Port 1 Ctrl C Switcher BINTI WETE versions Select All Monitors Monitor s etup r n Current Database Com 9 Groups Ca
13. s might take a few minutes 9 When the data transfer is complete click Close 6 2 UPLOADING 1 Connect the switcher to your computer See section 6 1 Downloading 2 On the Download Upload menu click Transfer Data 3 Select the appropriate check boxes See Figure 14 Note The Download Upload Sequences check box remains unavailable until the Download Upload Monitors check box is selected 4 Click Upload to Computer 5 When uploading is complete click Close 20 1036512C September 2003 KTD 411 Programming Software User Manual Opening and Saving a Database 7 OPENING AND SAVING A DATABASE 7 1 OPENING AND SAVING AN EXISTING DATABASE 7 1 1 SAVE 1 On the file menu click Save Database As The dialog box in Figure 15 appears Save in I MatrixS witcher Ezi ea MatrixS witcherD ata mdb File name Save as type Figure 15 Save As dialog box 2 Enter a file name in the File Name field 3 Selecta folder in which to save the file 4 Click Save 7 1 2 OPEN 1 On the file menu click Open The dialog box in Figure 16 appears 1036512C September 2003 21 Opening and Saving a Database KTD 411 Programming Software User Manual 2 3 7 2 Open x in I MatrixSwitcher e Pi Ea File name MatixSwitcheData Files of type access Files mdb Cancel Figure 16 Open dialog box Click the name of the database you wish to open or type the name into the File
14. uence Thirty two groups can be programmed into twelve sequences See Figure 11 and perform the following 1 Click Group Setup in the main programming dialog box Figure 6 The Groups dialog box appears 2 Click the Group Setup tab 3 Select a group number Group Setup Group Sequence Setup m Select Group D9 EE en ER EE EE EE DS 089 BB JE JE JE JE JER r ET JE JE EE JR SE ZEL 2 JE AW we k BER JER r Group Properties Group Name kalatl Site Alarm Number Fr Monitor Number Site Number i 001 MONO RON om Figure 11 Group Setup tab 16 10365120 September 2003 KTD 411 Programming Software User Manual 4 5 6 7 8 5 2 In the Group Name box type a name for the group Groups In the Site Alarm Number box type the number of the site alarm that will call up this group when the alarm is activated Click in the Site Number field corresponding to each monitor and type the number of the camera to appear Click Save Group Repeat steps 3 through 7 for additional groups GROUP SEQUENCE SETUP See Figure 12 and perform the following Group Setup Group Sequence Setup r Select Sequence 1 oe BE BE 5 ew BER i gr i e 10 e il e Te r Universal Dwell Time Sequence Step Dwell Time j2 v Saved Dwell Time 2 Sep Grou number Gropname Dwel Tne 1 01 2 Kalatel Figure 12 Group Seque
15. ve Sequence 8 Repeat steps 2 through 7 to set up other sequences 1 6 14 1036512C September 2003 KTD 411 Programming Software User Manual Programming Monitors 4 3 2 SEQUENCE 7 Sequence 7 always begins at camera 0 and runs up to the camera assigned in the Highest Camera Number box see Figure 10 See Figure 10 and perform the following x Monitor Setup Arming Cameras Monitors Sequence Setup Sequence Number Highest Camera Number re EN 1 2 3 4 5 6 7 Camera Name Step Camera Dwell Time 000 Kalatel 01 DigiPlex p d d T Sequence o gt Delete From Sequence 009 Shannon 010 AE eee Universal Dwell Time Sequence Step Dwell Time 2 F Saved Dwell Time 2 Note Sequence 7 runs from camera up to the camera assigned in the highest camera number field romere meih fe ie an te et O w Figure 10 Monitors Sequence Setup tab for sequence 7 1 Select Sequence Number 7 2 Inthe Highest Camera Number box enter the number of the camera at which the sequence will end Note If the Saved Dwell Time is not appropriate click the Monitor Setup tab and change the Universal Dwell you must click Save Mon Setup 3 Click Save Sequence 4 Click Close 1036512C September 2003 15 Groups KTD 411 Programming Software User Manual 5 GROUPS 5 1 GROUP SETUP You can program groups of cameras to appear on specific monitors in a seq
Download Pdf Manuals
Related Search
KTD 411 kts 41101 type kd 4110-tl