Manual (english)
Contents
1. User manual CDXM 3000 A re el L 1 oe SO Safety instructions 1 1 Controller function Mixing Console Function Connection FOR SAFE AND EFFICIENT OPERATION Technical data gt Table of content 2 10 EE 1 Safety instructions e This device is suitable for indoor use only e All modifications to the device will void the warranty e Repairs are to carry out by skilled personnel only e Use only fuses of the same type and original parts as spare parts e Protect the unit from rain and humidity to avoid fire and electric shocks e Make sure to unplug the power supply before opening the housing 1 1 FOR SAFE AND EFFICIENT OPERATION Be careful with heat and extreme temperature Avoid exposing it to direct rays of the sun or near a heating appliance Not put it in a temperature bellow 41 F 5 C or exceeding 95 F 35 C Keep away from humidity water and dust Do not place the set in a location with high humidity or lots of dust Containers with water should not be placed on the set Keep away from sources of hum and noise Such as transformer motor tuner TV set and amplifier To avoid placing on un stable location Select a level and stable location to avoid vibration Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt If out of work contact sales agency immediately Any trou2. active DISPLAY LCD Display indicates the Track Numbers Time Remain Pitch Continue Single IN BUTTON LOOP SYSTEM This button sets the beginning point of the loop and the light is illuminated OUT BUTTON LOOP BUTTON When you press this button you set the end point of the seamless loop and you start the loop To finish the loop press this button again RELOOP BUTTON LOOP SYSTEM This button is used to start the last saved loop To finish the loop press this button again DSP REVERSE Push the reverse button to play your track in reverse push the reverse button again to cancel this feature 6 10 gt 26 27 28 29 30 31 DSP BRAKE In play mode push the brake button at first and then push Play Pause button the operation changes slowly from play to pause Push the Play Pause button again to cancel this feature SINGLE Press this button to switch between the SINGLE and CONTINUE play mode The selected mode is indicated on the LCD In SINGLE mode after each track the unit stops the reading In CONTINUOUS mode the unit reads all track and stops TIME BUTTON Use this knob to choose the time mode Elapsed time remaining time or total REPEAT BUTTON Use this button to repeat one track or all the tracks ofthe CD ID3 When you press the ID3 button the names of the songs are shown on the display PITCH CONTROL Use this fader to increase or decrease the speed of the track Slide up to decrease the pi
3. CH mode you may press the SCRATCH button to exit SCRATCH mode When you enter the JOG work mode the lamp lights up FOLDER TRACK SEARCH Allows you to navigate through folders or tracks similarly in either USB or CD mode When navigating through a standard CD turn the rotary to the right to advance the selection or turn the rotary to the left to decrease the selection When you enter the SD work mode the lamp lights up When you enter the USB work mode the lamp lights up USB PORT Enables connecting any USB memory stick 3 IN 1 CARD SLOT Slot for inserting a 3 IN 1 card The contacts of the card must point downwards The unit cannot read cards with a capacity of more than 4 GB The unit is not compatible to SDHC cards and only supports the MP3 format USB SD Select the audio source between USB storage and SD card PITCH BUTTON Pitch on off switch The adjustment of the pitch potentiometer is available when pitch state is on and the light is illuminated INPUT TOGGLE SWITCH Selects which source will be live to that channel based on what you have connected to the rear panel input section In USB 1 or SD 1 position the internal USB 1 or SD 1 units are active CUE FOR CH1 2 Selects which source will be live to that channel for CH1 amp CH2 INPUT TOGGLE SWITCH Selects which source will be live to that channel based on what you have connected to the rear panel input section In USB 2 or SD 2 position the internal USB 2 or SD2 units are
4. bles arose remove the power plug soon and contact with an engineer for repairing do not open the cabinet by yourself it might result a danger of electric shock Take care with the power cable Never pull the power cable to remove the plug from the receptacle be sure to hold the plug When not using the device for an extended period of time be sure to disconnect the plug from the receptacle 3 10 gt Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried out by qualified personnel All electrical and mechanical connections have to be carried out according to the European safety standards 2 Technical data Features Scratch Mode DSP Brake Reverse ID3 Range of adjustments 12 Pitch range 4 8 16 Connections 2 x USB A MP3 FAT32 2 x 3 IN 1 Card Slot MP3 FAT32 1 x asym XLR 6 3 mm Mic In 1 x 6 3 mm Headphones 2 x Ground Turntables Line In 2 x asym RCA Line Out 2x asym RCA Power supply 100 240 V 60 50 Hz Power consumption 1400 VA Dimensions 482 x 90 x 80 mm Weight 6 Kg 4 10 N BD D T Na iD Ai U P 4 Oi OO JOG amp SHUTTLE WHEELS Search Touch the dial and rotate it to navigate through the track Press the jog mode button and the light is illuminated first Pitch While play
5. ill sound very bad so always be sure to toggle the line phono switch over to line before connecting line sources GND Grounding plug for turntable connection Always use this connection when using turntables Your turntable cable should have a grounding wire 9 10 Importer B amp K Braun GmbH IndustriestraBe 1 D 76307 Karlsbad www bkbraun com info bkbraun com X RoHS mm 7 10 10
6. ing rotate the dial to adjust the pitch bend Cue point In pause state rotate the dial to navigate through the track and once you enter a desired point press the Play Pause button Then the CUE button light blinks three times to show that the point was recorded successfully Note Rotate the dial clockwise is forward counterclockwise is backward PLAY PAUSE BUTTON Each time you press the PLAY PAUSE button the operation changes from play to pause or from pause to play CUE BUTTON To define and record a return point from which playback starts again PITCH BEND BUTTON The pitch speeds up when the button is pressed and returns to the original pitch when it is released PITCH BEND BUTTON The pitch will slow down while the button is pressed and returns to the original pitch when it is released REPLACEABLE CROSSFADER Enables clean segues between the two input channels Hard left selects channel 1 Hard right selects channel 2 When the crossfader is centered both assigned channels are live Use the crossfader for fast and seamless segues from one selected channel to the other SCRATCH MODE When the 10 is illuminated the wheel is in SCRATCH mode you may press the SCRATCH button to exit SCRATCH mode When you enter the JOG work mode the lamp lights up 5 10 EE 10 11 12 13 14 19 16 17 18 19 20 21 22 23 24 25 SCRATCH MODE When the 10 is illuminated the wheel is in SCRAT
7. tch and slide down to increase the pitch 7 10 USB2 PHONO2 sD 2 LINE 2 32 LED METER Indicates the master output level 33 41 CH1 amp CH2 GAIN CONTROL Adjusts CH1 amp CH2 level 34 40 HIGH FADER 1 2 Adjust CH1 amp CH2 equalization of high 35 39 LOW FADER 1 2 Adjust CH1 amp CH2 equalization of low 36 38 INPUT FADER Controls individual source levels for CH1 2 in the mix 37 HEADPHONE VOL Adjust headphone level 42 MIC VOL Adjust microphone level 43 MASTER VOL Adjust master level output 8 10 44 45 HEADPHONE JACKS This is used to connect headphones for audio monitoring DJ MIC For plugging in a XLR type microphone 5 Connection 46 47 48 49 50 51 um HAAN rm m ATT NN pply Power source 100 240V 60 50 Hz Power cons um ption 8 WATTS AG CORD Use this cable to connect the AC mains power to the unit POWER BUTTON Press the power switch to turn on the unit To switch the POWER off press the POWER switch again STEREO MAIN OUTPUT Unbalanced RCA connectors are controlled by the master fader INPUT Plug in a line level device such as tape deck or additional CD player here LINE PHONO INPUT SWITCH Use this to allow either line level or phono level equipment to be plugged into your channel inputs When phono input is selected your signal is fed directly to the high quality RIAA phono preamplifiers Line level sources will overload the sensitive phono pre amps and w
Download Pdf Manuals
Related Search