Pac 7000 IFU
Contents
1. Drager Pac 7000 Drager Pac 7000 is not for use in oxygen enriched atmos pheres Please check calibration before safety relevant use The performing of calibration and bump testing shall be con ducted according to local regulations Do not inhale the test gas Observe the hazard warnings of the relevant Safety Data Sheets The gas opening is equipped with a dust and water filter This filter protects the sensor against dust and water Do not destroy the filter Replace destroyed or clogged filter immediately see Changing dust and water filter on page 6 2 Intended Use Personal gas alarm in the workplace 3 What is What St 5047 5053 2004 eps 1 Alarm LED 6 Gas Opening 2 Horn 7 Screw 3 Concentration Display 8 Clip 4 OK Key On Off Alarm Acknowledge 9 Label 5 Key Off Bump Test 10 IR Interface OORUN 4 4 1 Cia AND mg m3 VOL PPM 7 Error Icon 8 Bump Test Icon 9 Low Battery Icon 10 Selected measuring unit 11 Concentration display Fresh Air Calibration Icon Span Calibration Icon Password Icon Peak Concentration Icon TWA Icon STEL Icon Operation Turning the instrument on Press and hold OK The display counts down until start up 3 2 1 All display segments are lit Next the LED Alarm and Vibrat ing alarm are activated in sequence Please check these be fore each use The instrument will perform a self test The software version and the gas name are displa2. Spent batteries may be returned to Drager Safety for dispos al 9 Sensor 9 1 Changing the sensor Do not change the sensor in explosion hazard areas Replace sensor when instrument can no longer be calibrated Use only the DragerSensor XXS of the same gas type Turn the instrument off Unscrew the 4 screws from the back case Open the front case and remove the battery Remove the sensor Insert the new sensor Press and hold OK for approx 3 seconds while battery is not installed Insert the battery according to specified polarity Place front case back and fasten it by tightening the 4 screws of the back case After inserting the battery a sensor warm up time is needed see chapter 11 The gas value flashes until the warm up time has passed After changing the sensor and after the warm up time is fini shed the instrument must be calibrated see chapter 5 3 10 Instrument alarm The alarm and LED will be activated three times periodically The X icon is flashing a 3 digit error code will be shown in the display lf an error appears in the display see chapter 10 1 and if necessary please contact Service of Drager Safety 10 1 Trouble shooting errors Flash EEprom write Contact Service failed 1102 AD system defect Contact Service lash check sum wrong Contact Service Most recent settings Recalibrate instrument restored Self test failed Contact Service fail
3. Drager Pac 7000 en de fr es pt it ni da fi no Instructions for Use 52 6 Gebrauchsanweisung 37 11 Notice d utilisation 512 16 Instrucciones de uso 5 17 21 Instru es de utiliza o 22 26 Istruzioni per l uso 527 32 Gebruiksaanwijzing E 33 37 Brugsanvisning 538 42 Kayttoohjeet 543 47 Bruksanvisning 48 52 SV et pl ru hr sl sk CS Bruksanvisning 553 57 Kasutamisjuhised 558 62 LietoSanas instrukcija 63 68 Naudojimo vadovas 69 73 Instrukcja obstugi 574 79 PyKOBOACTBO NO 3KCnnyaTalnu 580 85 Upute za uporabu 86 91 Navodilo za uporabo 92 97 N vod na pou itie 98 103 N vod na pou it 104 108 bg ro hu el tr ar zh ja ko Drager PbKOBOACTBO 3a paboTa 109 114 Instructiuni de utilizare 5 115 120 Hasznalati utmutato 5 121 126 OSnyiec Xpnons 127 132 Kullanma talimati 5 133 137 SLaxiuY 4a yb 138 142 AE Fiat A 143 147 Arikan las 148 153 AS 4A 3154 158 1 For Your Safety The use of the Drager Pac 7000 instruments assumes a complete knowledge and adherence to the user s manual In areas that are subject to explosion hazards the Drager Pac 7000 can only be used if these hazards are explicitly covered under the Ex Approvals which have been granted to the
4. Drager Pac 7000 is equipped with a data logger The data logger stores events and the peak concentration measured during during a variable interval adjustable with Pac Vision or CC Vision The data logger runs about 5 days in a 1 minute intervall If the memory of the data logger is filled the data log ger overwrites the oldest stored data For adjustment of the peak concentration to be stored or for download of the stored data connect Drager Pac 7000 to a PC using the connecting cradle or the E Cal System The stored data can be downloaded with installed software Pac Vision or CC Vision 6 2 Adjustable operation timer in days Drager Pac 7000 is equipped with an adjustable operation timer The operation timer can be used to set an individually operation period e g to adjust a calibration due date an Inspection due date an out of order date a usable life alarm etc To adjust the operation timer connect Drager Pac 7000 toa PC using the connecting cradle or the E Cal System The ad justment can be done with installed software Pac Vision or CC Vision 6 3 Usable life alarm end of operation period A useable life alarm can be adjusted using the adjustable op eration timer see chapter 6 2 If an operation period is set a warning period begins before the end of the installed operation period During this period the remaining life time flashes just after turning the instrument on e g 30 d This alarm occurs
5. ading 11 4 Sensor Specifications and Instrument Settings for other Gases Es Se Ny Se Tbe Measuring Range 0 300 ppm O 100 ppm 0 20 ppm 0 50 ppm O 50 ppm 0 5 vol 0 20 ppm O 100 ppm O 200 ppm 0 200 ppm 50 ppm in No 10 ppm in N 0 5 ppm in No 10 ppm in Ns 10 ppm in N 2 5 vol in air 5ppminNo 20 ppm in No 20 ppm in N 20 ppm in No Temperature range operation 30 50 C 30 50 C 20 50 C 20 50 C 30 50 C 20 40 C 30 50 C 40 50 C 20 50 C 20 50 C a 22 122 F 22 122 F 4 122 F 4 122 F_ 22 122 F 4 104 F 22 122 F 40 122 F 4 122 F 4 122 F Alarm Threshold A1 50 ppm 1 ppm 0 1 ppm 10 ppm 5 ppm 0 5 vol 0 5 ppm 1 6 ppm 10 ppm 10 ppm acknowledgeable Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes latching No No No No No No No No No No Alarm Threshold A2 100 ppm 2 ppm 0 2 ppm 20 ppm 10 ppm 3 vol 1 ppm 3 2 ppm 20 ppm acknowledgeable No No No No No No No No o latching Yes Yes Yes Yes Yes Yes Yes Yes Yes N TWA Threshold AT 50 ppm OS vol OS ppm N o STEL Threshold A2 50 ppm 1 ppm 0 1 ppm 40 ppm 5 ppm 2 vol 0 5 ppm 5 ppm No No of STEL periods 4 4 4 4 4 4 4 4 o Average STEL duration 15 minutes 15 minutes 15 minutes 15 minutes 15 minutes 15 minutes 15 minutes 15 minutes No Reproducibility Zero point Sensitivity of measured value Drift 20 C Zero point l
6. an standard EN 50073 Enter the password To enter the calibration menu press the 3 times within 3 seconds The instrument beeps twice quickly The notice icon begins to flash Press again If a password has been set three zeros 000 will appear on the display with the first zero flashing The password is entered one digit at a time Change the value of the flashing digit by pressing and press OK to accept the value The next digit will now be flashing Repeat this process to select the next two values After the last acceptance using the OK button the password is complete Note the default password is 001 If a correct password has been entered or no password has been set the display shows the icon for fresh air calibration flashing Press OK to enter the fresh air calibration function or press to switch over to the span calibration function After this the display shows the icon for span calibration flashing Press OK to enter the span calibration function or press again to switch over to the measurement mode 5 2 Fresh air calibration To enter the fresh air calibration function press OK after entering the menu while the fresh air calibration icon flashes The fresh air calibration icon stops flashing and the indicated value flashes To finish the fresh air calibration press OK the fresh air calibration icon is removed from the display and the instru ment returns to the measuring mode If the f
7. at 10 of the set operation period or at least 30 days before end of the operation period To acknowledge this message OK must be pressed After that the instrument can be used further After the usable operation period has expired the text 0 d will alternate in the display and cannot be acknowledged The instrument will not longer measure 6 4 Measurement of COHB Drager Pac 7000 CO version is equipped with a measuring mode to measure HBCO in exhaled air The exhaled CO provides a convenient and reliable concentration value to measure the carboxyhemoglobin COHB content of the blood To activate this function connect Drager Pac 7000 to a PC using the connecting cradle or the E Cal System The adjust ment can be done with installed software Pac Vision or CC Vision After activation of this function the display alternates between HB and a concentration The concentration will be indicated in the unit of COHB For the measurement connect Drager Pac 7000 to the cali bration adapter and connect a mouth piece Drager order code 68 05 703 to the calibration adapter Blow into the mouth piece for approximately 20 seconds Wait for the highest indication in the display During calibration and bump test the instrument reverts back to the regular ppm CO mode and returns to COHB mode once finished There are no gas alarms and no TWA STEL measurements available in COHB mode 7 Alarms 7 1 Concentration Pre Main Alar
8. d Configuration incomplete Configure again 24 Bump test failed Repeat operation or calibrate instrument 11 Technical Specifications 1 1 1 1 Broken or missing Ov Replace O sensor sensor 00 02 04 05 06 07 08 09 0 11 1 General Environmental Conditions During operation temperature see 11 3 and 11 4 700 to 1300 hPa 10 to 90 relative humidity O to 40 C 32 to 104 F 30 to 80 relative humidity 24 hours of use per day 1 minute alarm per day gt 5 500 hours Oo gt 2 700 hours typical 90 dBA at 30 cm 1 ft 64 x 84 x 20 mm battery compartment 25 mm 2 5 x 3 3 x 0 8 battery compartment 1 in Weight 106 g 3 8 oz Ingress protection IP 65 Approvals see Approvals on page 159 Conditions for storage Battery life typical at 25 C Intensity of alarm Dimensions without clip 11 2 Standard Configuration Factory Settings 0 Data Logger Interval Bune 7 COHB Mode 1 For measurements according to EN 45544 CO HS or EN 50104 O3 the Life Signal must be switched on 11 3 Sensor Specifications and Instrument Configuration Principle of measurement is an electrochemical 3 electrode sensor Oxygen O3 cannot be measured in the presence of Helium He The Type Examination Certificate covers the measuring function for Oxygen enrichtment and defficiency OS A Temperature range operation 20 50 C 20 50 C 20 50 C Alarm Threshold A1 ackn
9. easurements according to EN 45544 CO H2S or EN 50104 Oz the Life Signal must be switched on To illuminate the display press 4 5 Show peak concentration TWA and STEL During measuring mode press OK The peak concentration and the peak concentration icon will be shown After 10 seconds the display will return to the measuring screen or if OK is pressed again the TWA concentration and the TWA icon will be shown After 10 seconds the dis play will return to the measuring screen or if OK is pressed again the STEL concentration and the STEL icon will be shown After 10 seconds the display will return to the meas uring screen or if OK is pressed again the number of STEL periods and the STEL icon will be shown After 10 seconds the display will return to the measuring screen 4 6 Turning the instrument off Simultaneously hold both keys for approximately 2 seconds until 3 appears in the display Continue to hold both keys until the countdown is finished The alarm and LED will be activated momentarily 5 5 1 Calibration Drager Pac 7000 is equipped with a calibration function The instrument will automatically return to the measuring screen if no key is pressed in the calibration menu for 1 minute except in the span calibration menu which will wait for 10 minutes Calibration shall be performed by trained personnel if the bump test is failed or after specified calibration intervals see chapter 11 and Europe
10. er the sensor If gas concentration exceeds the alarm thresholds A1 or A2 the corresponding alarm will occur To finish the bump test press OK the icon is removed from the display and the instrument returns to the measuring mode If during the bump test no alarm occurs within 1 minute the instrument alarm mode is entered to indicate failure The error icon X and the notice icon are flashing error code 240 is shown upon acknowledgement is shown instead of the measured value and the X and icons are lit In this case the bump test can be repeated or the instrument can be calibrated The result of the bump test passed or failed will be stored in the data logger see chapter 6 1 The bump test can also be made by an automatic function This function can be activated using the PC software Pac Vision or CC Vision see chapter 6 If the bump test mode was entered by mistake while the notice icon was not lit and no gas flow over the sensor press to cancel the bump test mode and switch over to measurement screen 4 4 During operation If the allowable measurement range is exceeded or a nega tive drift occurs the following will appear in the display TTT too high concentration or LLL negative drift Alarms are indicated as described in chapter 7 Continuous function of the instrument is indicated by the life signal which is a beep every 60 seconds if configured see chapter 11 For m
11. larm sounds in a repeating pattern of 2 repeating tones and the LED blinks in the same pattern The battery main alarm is not acknowledgeable the instru ment will automatically turn off after approx 10 seconds Incase of avery low battery the internal voltage monitor could activate the LED s 8 Battery 8 1 Changing the battery Do not change the battery in explosion hazard areas The instrument contains a replaceable lithium battery The battery is part of the Ex approval Only the following battery types shall be used Duracell 123 Photo Lithium 3 V Duracell 123 Ultras Lithium 3 V Panasonic CR123A Lithium 3 V Energizer EL123A Lithium 3 V Powerone CR123A Lithium 3 V Turn the instrument off Unscrew the 4 screws from the back case Open the front case and remove the depleted battery Press and hold OK for approx 3 seconds while battery is not installed Insert the new battery according to specified polarity Place front case back and fasten it by tightening the 4 screws of the back case After changing the battery a sensor warm up time is needed see chapter 11 The gas value flashes until the warm up time has passed 8 2 Handling of exhausted batteries Caution Never throw them into a fire Never attempt to charge them Never attempt to open them danger of explosion Dispose of exhausted batteries only as special waste in accordance with local regulations
12. ms The alarm will activate whenever the alarm thresholds A1 or A2 are exceeded The instrument is equipped with a vibrating alarm It vibrates in parallel to these alarms During an A1 the LED will blink and the alarm will sound During an A2 the LED and alarm tone will repeat in a double repeating pattern The display will alternate between the measurement value and A1 or A2 When the TWA A1 alarm is activated the TWA icon flashes in addition to the audible optical and vibrating alarm When the STEL A2 alarm is activated the STEL icon flashes in addition to the audible optical and vibrating alarm The alarms may according to the selected configuration be acknowledged or turned off see chapter 11 Acknowledge able alarm tone and vibration can be acknowledged by pressing OK Latching The alarm will only deactivate when the concen tration falls under the alarm threshold and then OK is pressed Ifthe alarm is not latching the alarm will deactivate as soon as the concentration falls under the alarm threshold 7 2 Battery pre main alarms When the battery pre alarm is activated the audible alarm sounds and the LED blinks and the low battery icon flashes To acknowledge the pre alarm push OK After the first battery pre alarm the battery will last for approx 1 further week and the low battery icon stays lit When the battery main alarm is activated the audible a
13. nd press OK to accept the value The next digit will now be flashing Repeat this process to select the next three values After the last acceptance using the OK button the calibration concentration is complete Open the regulator valve to let calibration gas flow over the sensor flow 0 5 l min Press OK to start the calibration The concentration flash es When the indicated value shows a stable concentration press OK If the calibration is successful a short double beep occurs and the instrument returns to the measuring mode If the calibration failed a long single beep occurs is shown instead of the measured value and the X icon and the span calibration icon are lit In this case the cal ibration can be repeated 5 4 Adjustment of the password 6 1 For adjustment of the password connect Drager Pac 7000 to a PC using the connecting cradle or the E Cal System The password can be adjusted with installed software Pac Vision or CC Vision Note If the passowrd is set to 000 this means no password is set Maintenance and Configuration The device does not need any special maintenance For individual configuration or individual calibration connect Drager Pac 7000 to a PC using the connecting cradle or the E Cal System Configuration and calibration can be done with installed software Pac Vision or CC Vision Strictly follow the instructions for use of the modules and software in use Data logger
14. owledgeable latching Alarm Threshold A2 23 vol acknowledgeable No latching Yes STEL Threshold A2 No No of STEL periods No Average STEL duration No Warm uptime switch on Warm up ime Sensor or batery change Reproducibility Zero point Sensitivity of measured value Drift 20 C Zero point lt 0 5 vol a Sensitivity of meas value month lt 1 lt 1 7 71 seconds 7718 seconds 12720 seconds Zero error EN45544 C emm em Standards performance tests for toxic gases and EN 45544 EN 45544 EN 50104 oxygen deficiency and enrichment Type Certificate EN 50271 EN 50271 EN 50271 PFG 07 G 003 Sensor Order Number 6810882 6810883 6810881 Sensor Data Sheet Order Number 9023816 9023819 9023820 For O A1 is the lower alarm threshold used to indicate Oxygen deficiency Please be aware of special settings by customer requirements Please be aware of limited lifetime of sensors Excessive storage reduces operating time of sensors Temperature range of storage is 0 35 C 32 95 F WN Sra Cross senstviy acors J CO HS J O Carbon mononde regigbe 02 T5 reggie negligible Methane negligible negligible negligible Hydrogen sulphide s0 03 negligible negligible Nitrogen dioxide lt 0 05 lt 0 25 negligible negligible negligible negligible Sulphur dioxide lt 0 04 negligible 4 Multiply cross sensitivity factor by gas concentration to get re
15. resh air calibration failed a long single beep occurs is shown instead of the measured value and the X icon and the fresh air calibration icon are lit In this case the fresh air calibration can be repeated or the instrument can be calibrated 5 3 Calibration 5 3 1 Automatically Calibration With Drager Bump Test Station Printer the unit can be con figured to automatically start a calibration after a failed bump test without pressing any key 5 3 2 PC based Calibration For calibration connect Pac 7000 to a PC using the connect ing cradle or the E Cal System Calibration can be done with installed software Pac Vision or CC Vision A calibration due date can be set using the operation timer in days 5 3 3 Calibration without PC Pac 7000 is also equipped with an onboard calibration func tion Prepare the calibration cylinder connect the cylinder to the calibration adapter and connect the calibration adapter to the instrument To enter the span calibration function press OK after entering the menu while the span calibration icon flashes Now the calibration icon stops flashing and the adjusted cal ibration concentration flashes It is possible to use this adjusted calibration concentration or to change it to be in line with the concentration of the gas cylinder To change the adjusted calibration concentration press The first digit flashes Change the value of the flashing digit by pressing a
16. t 0 2 vol a lt 0 2 ppm a lt 0 2 ppm a lt 5 ppm a Sensitivity of meas value month lt 15 lt 2 lt 5 lt 2 Sensor Order Number 1 68 68 10 889 68 10 890 68 11 525 68 11 530 68 11 535 Sensor Data Sheet Order Number 90 23 922 90 23 919 90 23 920 90 23 921 90 23 918 90 23 923 90 23 924 90 23 970 90 23 994 90 23 995 Please be aware of possible sensor cross sensitivities see Sensor Data Sheet 12 Accessories 13 Changing dust and water filter Connecting Cradle complete with USB cable and Pac Vision software 83 18 587 Calibration Adapter 83 18 588 Lithium battery 45 43 808 Dust and water filter 45 43 836 Leather carrying case 45 43 822 Bump Test Station complete with test gas cylinder 58 L 83 18 586 gas type by customer request E Cal instrument module for connection of 4 Drager Pac 1000 to 7000 to a E Cal Master Station or to Module 83 18 589 Adapter Drager Bump Test Station Printer complete with test gas cylinder 58 L including Auto Detect Function for 83 21 008 Pac 7000 gas type by customer request 1 Please be aware of limited lifetime of sensors Excessive storage reduces operating time of sensors Temperature range of storage is O to 35 C 32 to 95 F 2 Please be aware of special settings by customer requirements 3 For ethylene oxide only ps 00223826_04 e
17. yed The A1 and A2 alarm limits are displayed After max 20 seconds the gas concentration Is displayed and the instrument is ready for use For the O sensor after the first turning on of the instrument a sensor warm up time of up to 15 minutes is needed The gas value flashes until the warm up time has passed 4 2 Before entering a working place After turning the instrument on the actual measurement value will normally be shown in the display Check for the notice icon When lit it is recommended that you perform a bump test as described in chapter 4 3 Clip the instrument to clothing before working in or near potential gas hazards Insure that the gas opening is not covered and that the instru ment is also near to your breathing area 4 3 Performing a bump test with gas Prepare a Drager test gas cylinder with 0 5 l min and a gas concentration higher than the alarm threshold to be tested Connect Drager Pac 7000 and the test gas cylinder to the calibration adapter or connect Drager Pac 7000 to the Drager Bump Test Station To enter the bump test mode press the 3 times within 3 seconds The instrument beeps twice quickly The notice icon begins to flash ps 00123826_04 e Remark With Drager Bump Test Station Printer the unit ca ou n be configured to automatically start the bump test with t pressing any key To activate the bump test press OK Open the regulator valve to let test gas flow ov
Download Pdf Manuals
Related Search