SCM-PD-PLUS-COMBO User`s Manual
Contents
1. Color Lights on locations 3 and 4 Note that the jumper on the upper left corner of the board is installed for this power configuration 6 Mount the Box The box can be mounted with the included 8 stainless steel pan head mounting screws 7 Connect the Lights Loosen the cable glands and route the cable through Strip the outer cable pack approximately 1 5 inches and the ends of the wire back approximately 25 of an inch The connectors are color coded Insert each wire into the respective location and snap the connector down Note that the green wire from the Color Casters is left unconnected The blue connector 1s for the blue wire on Shadow Caster single color lights Note that the lights should typically be connected consecutively for implementation of chase modes Le light moves from one light to the next in a linear pattern 8 Connect Input Power Route power into the box directly from a breaker or main fuse panel See Diagram 1 The breaker and incoming wire should be sized appropriately to the number and current draw of the lights being connected Pwr and Gnd are clearly marked on the printed circuit board The power connector will accept from 2awg to 20awg wire For installations where it is desired to switch the power directly see Diagram 2 Installation of the blue jumper on the upper left hand corner of the board will be necessary for this configuration See Picture 1 9 Install the pre wired switch Diagram 1 shows th2. communicate with and coordinate the color changing feature of all Shadow Caster color changing lights The SCM PD PLUS is also fully compatible with Shadow Caster single color lights The SCM PD PLUS will support a full range of color changing fading strobing flashing and chase modes Installation Steps 1 Configure the SCM PD PLUS Set the 6 position dip switch SW3 and the 3 position switch SW2 On SW3 each switch enables corresponding channels through 6 The install locations do not have to be consecutive SW2 three position switch functions are listed below The SCM PD PLUS comes pre configured with network communications enabled chase mode disabled and standard color range selected See Picture 1 Page 2 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com SCM PD PLUS COMBO SW2 3 Position Switch Settings Switch 1 Network Enable Enables Shadow Net Switch 2 Chase Mode Enables Chase Mode Moves Color Support from 4 to 12 only Switch 3 Extended Colors works with Accent Lighting Controller and full color SC 40s onto AAA r MOOR o AARAA gt A4 Eds 45 3 T 270 EEE FEES u el Picture 1 PD PLUS box showing locations of SW 2 SW 3 remote bypass and Programming button 2 Find a suitable mounting location This box should be mounted in a dry location such as high in the bilge area below the deck or inside the console It is preferred to not have the cable glands or the power wire connector
3. facing up where moisture will drain into the box Select Antenna Mounting Location Once the power distribution box mounting location and orientation has been selected a suitable location for the antenna should be determined The ideal mounting option will have the Antenna mounted as high as possible and as far as possible from large metal objects Additionally the antenna should be as far as possible from potential sources of electrical interference and oriented vertically There is a right angle adapter included to increase mounting options If a suitable mounting position still cannot be found or if there is poor performance contact Shadow Caster regarding the availability of a remote mount extended range antenna Part SCM Antenna Extended Page 3 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com SCM PD PLUS COMBO 4 Mount Antenna in box Verify that the 5 SMA to U FL Coax Jumper will reach from the Antenna PCB to the chosen location Once Verified drill a slightly larger than 25 diameter hole through the PD PLUS box Exercise Caution to not damage any components on the PCB Install the SMA bulkhead with included nut and washer Use RTV or silicon to seal around the SMA bulkhead Screw in stub antenna to the bulkhead 5 Insert Wireless Card into PD PLUS Simply slide the Wireless Card as shown in Figure 1 If the U FL connection to the board has become disconnected simply press together to snap back on Co
4. SCM PD PLUS COMBO shacdow caster MARINE LEDs SCM PD PLUS shown with optional SCM WC SN wireless controller installed SCM Power Distribution PLUS COMBO system Installation and User Instructions Chado w nefF ENABLED Page 1 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com SCM PD PLUS COMBO SCM PD PLUS COMBO includes NEMA Box with Power distribution Board and 6 outputs Box Lid and 6 screws 7 5 Amp Fuses Installed SS 316 PH 8 x1 2 Mounting Screw Shadow Caster Lanyard Tools Required Phillips head screwdriver wire strippers 257 261 F or G Diameter Drill and RTV for sealing the antenna bulkhead The Shadow Caster Power Distribution PLUS SCM PD PLUS provides a convenient way to connect and control multiple Shadow Caster Lights The incorporated Shadow Net communications enables compatibility with Shadow Caster s color changing and single color lights The SCM PD PLUS COMBO includes a wireless controller for remote control of Shadow Caster lights The SCM PD PLUS has on board power switching for 6 lights and up to 100 amps Each light is individually switched and has its own fuse The on board power switching feature greatly simplifies installation by allowing the power to be taken locally from a main breaker as opposed from the helm The lights are controlled with a pre wired waterproof switch Shadow NET is a communication protocol that allows the SCM PD PLUS to
5. THERS SPECRIED MAME DATE Sh 7 rig Ww Gr sie m EMMAEREONE ARE IH MCHES DESH FE P 3051 RDOO HOOK UP STRND AWG RED 7 30 PVC TOLERANCES eu ead pur ANGULAR MACKS REND cures B Roger amma MILE de 18 GA 4 CONDUCTOR PVC JACKET nes cine un P Distribution FI 25 FT 518XXXNC199 nee THREE PLACECECMAL 000 appeoveD ower Distribution Plus WHITE ee Switch Drawing THE BOAO CON MED THe ATER DERMEE oOo nn Cane spears er nn ee y PI PAE GE AE A NACE mo TTA maa B SC PLUS TASM 12001 2013 SHADOW CASTER LED LIGHTING LLC SHADON CASTER ES PEOHSTED PEE EREE ST nr a 7 5 4 a 2 1 Page 9 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com SCM PD PLUS COMBO Page 10 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com
6. e pre wired switch configuration The switch power can be taken from the same source as the lights or from a local source at the installation of the switch The current draw for the Page 5 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com SCM PD PLUS COMBO switch circuit will be 250mA See attached drawing for dimensions and schematic 10 Cinch the cable glands Hand tighten all cable glands Verify that any unused cable glands have a nylon dowel inside so that a water tight seal is maintained 11 Configure Fuses The Power Distribution box comes standard with 7 5Amp fuses to accommodate Color Casters and SCM 10 size lights on a 12 Volt power bus If different size lights or installing on a 24Volt bus please see Chart for appropriate fuse selection Chart 1 Fuse Recommendations Suggested Fuse Size 12V system 24V system 12 Wireless Controller If Installing Wireless Controller Model SCM WC SN please see the documents included for installation and operating instructions 13 Final Setup and Auto Programming Power up the SCM PD PLUS box Press and hold the auto programming button for three seconds and release All of the lights will turn off then cycle back on one at a time starting with light one The system will communicate with each light and determine what is present Once this process completes cycle the power to the box again The system is now ready to use 14 Install Cover Install clear enclosu
7. nnect f RE UMP ER L un PD PLUS g pee n D oa r i Va 5 Shadow NET 12V DC G ON O ss E LED Ce 2 OFF Cnase mode Enanie BOX aS i Indicator LED gt A ce Push Button 3 OFF Ex Coior Range SW3 6 position Dip Switch ON EUR Set to ON when Light 1223456 iS present Light 1 Light 2 Light 3 Light 4 Light 5 Light 6 Diagram 1 Typical installation of SCM PD PLUS shown with 6 Color Caster Lights Note that Green Wire from Color Casters are not connected Page 4 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com SCM PD PLUS COMBO INS SOR UMPER 12 3 Power Switch Bypass Push Button Switch ON PD PLU S Optional Shadow NET H r m Shadow NET L Mode Setup SW2 re D on ND 1 ON NetworkEnable BOX 12V In Switched 7 2 OFF Chase mode Enable Indicator LED 3 OFF Color Range Push Button 6 Position Dip Switch 7 f Light Position Setup SW3 LOV 30VDC Set to ON when Li g htis 1 ON Color Caster Installed presen t 2 ON Color Caster Installed FUSE or Located at connection to A N ON 4 ON Single Color Light Installed Circuit power source 5 OFF No Light Installed l Breaker N 123456 6 OFF No Light Installed HT GND ChL LJ C Light 2 Light 3 Light 4 S D l Diagram 2 Optional wiring Configuration for SCM PD PLUS shown with Color Caster Lights on locations 1 and 2 Single
8. re lid with 6 supplied screws Page 6 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com SCM PD PLUS COMBO Operation of PD PLUS with switch 1 Turn on the power switch and the lights will power up 2 To change the color simply press the Momentary switch and release Chart 2 Press Momentary Button to Change Color Red 3 To Change the MODE press and hold the switch in for 2 seconds then release Chart 3 Change Mode Press and hold button for 2 seconds Chase Mode Enabled On Normal Operation and Use of Wireless Controller There are 4 commands issued from the remote control 1 MODE Press to go to next available color See Chart 2 above 2 CONTROL Changes the speed of a routine No effect when on solid color 3 Holding MODE for 2 seconds Moves to next routine see Chart 4 below 4 Hold CONTROL for 2 seconds Powers off all lights and puts the system into standby Page 7 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com SCM PD PLUS COMBO Chart 4 Press and hold MODE button for 2 seconds Chase Mode Enabled On Normal Fade Flash Strobe chase between all lights Replacing the battery in the FOB The Key FOB transmitter uses a CR2032 lithium coin cell battery These are commonly available where batteries are sold To replace the battery remove the two Phillips head screws on the back of the transmitter The battery slides out a
9. s shown in figure 10 Be careful to have the side of the battery facing as shown in figure 10 When reassembling the FOB case exercise caution to verify that the watertight seal is properly seated on the perimeter of the case Programming a new remote FOB If the remote FOB must be replaced the new one can easily be coded to the wireless receiver To do this power on the PD PLUS system then press the programming button on the receiver and release Then press and release the MODE button on the wireless receiver repeat this until the code is picked up by the receiver This can be verified by seeing the Shadow Caster Lights changing color Note that the wireless controller will only support one remote at a time Please contact Shadow Caster Lighting for additional support Shadow Caster Lighting 1237 Lady Marion Lane Dunedin FL 34698 info shadow caster com 727 474 2877 Page 8 SCM PD PLUS COMBO Instructions 2 5 15 www shadow caster com SCM PD PLUS COMBO a F 5 jcm REVISIONS REV DESCRIPTION DIMENSIONS IN MM i PRELIMINARY 1 31 2014 CHANGED WIRING SCHEME 3 19 2014 D Opticon Connect Nav Lights to pin 12V DC 4 feet long te fuse Place Label 12V Only CORTE Jumper to pain 4 if Naw Lights are net used Carling Switch LED Sa aaa ON OFF MOMENTARY WITH CUSTOM LOGO BLUE LED RED CONN 250 FEMALE SEALED Er 0191640017 B27 AWG ry BLUE CONN 250 FEMALE SEALED UNLESS O
Download Pdf Manuals
Related Search