operating and maintenance manual
Contents
1. 6 MACHINE DESCRIPTION Instruments washer dimensions 6 0 PUSH BUTTON CONTROLS 4 1 3 1 on off 2 light power 3 start delayed start 4 light Delay Start Washing phase 5 salt refill indicator 6 liquid rinse aid refill indicator 7 indicator light program 10 8 program selection button 9 start reset button _ Aci 12345686 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 7 INSTALLATION INSTRUCTIONS A Carefully remove and store the packaging B Carefully screw the hose water with the cold water tap C Connect the drain hose 7 0 METHOD OF CONNECTING FITTINGS GUIDELINES FOR WATER SUPPLY The washing machine must be connected to the main water supply pipes using new fittings The water pressure must be between 0 04 MPa and 1 MPa Remove the fittings for the water supply of the compartment on the back of lava tools Tighten the screws of the safety fitting for the connection to the tap with 34 Fully open the water tap before starting the washing machine Instructions A fitting connected to a faucet sprayer may burst if it is installed on the same pipe that is connected to the washing machine If there is this kind of connection disconnect the connector and plug the drain hole 7 1 DISCONNECT THE FITTING OF SAFETY Close the water tap Release the water pressure by pressing the pressure2. READ ALL SAFETY INFORMATION CONTAINED HEREIN AND UNDERSTAND ALL THE PLATES REPORTS SECURITY ON THE UNITS THE SIGNS ON THE UNIT MUST ALWAYS BE READ WELL REPLACE THEM IN CASE THEY GET WORN OR DAMAGED 6 NO WARRANTIES PROVIDED ON GOOD FUNCTIONAL OR ON SAFETY OF THE USER AND OR ENABLED PERSON AND OR ANY OTHER PERSON AND OR THE ENVIRONMENT IN THE EVENT THAT THE PROVISION OF ELECTRICITY NOT COMPLY WITH THE REQUIREMENTS OF THIS LAW AND U M M THE EQUIPMENT ONCE INSTALLED AND PUT IN SERVICE NOT COMPLY WITH THE REQUIREMENTS STATED IN THIS U M M THE DEADLINES SET MAINTENANCE ARE NOT RESPECTED 7 THE OPERATING SAFETY EQUIPMENT ALLOWS IT TO BE INSTALLED AND PUT INTO SERVICE BY QUALIFIED PERSONNEL RESPONSIBLE TO FOLLOW THE INSTRUCTIONS GIVEN IN THIS U M M AND RULES 8 THOSE WHO ARE NOT ABLE TO INSTALL START UP OR USE SAFETY ALONE OUR PRODUCT BECAUSE OF PHYSICAL SENSORY OR MENTAL INABILITY OR THROUGH INEXPERIENCE OR NO KNOWLEDGE THEY MAY CARRY OUT THE BUSINESS SPECIAL SUPERVISION ONLY IF INSTRUCTED BY COMPETENT PEOPLE WHO TAKE FULL RESPONSIBILITY 9 YOU MAY NOT USE WATER TO WASH THE MACHINE PARTS EXCEPT FOR SOME ACCESSORIES NOT EXPRESSLY REPORTED 10 IT IS FORBIDDEN TO REMOVE AND OR TAMPER WITH THE LABELLING AND SYMBOLS FROM ORIGINALLY AFFIXED REVERBERI 11 DO NOT PUT ANY OBJECT OVER EQUIPMENT 12 DO NOT TOUCH THE DEVICE WITH BODY PARTS WET AND OR BARE FEET 13 DO NOT PULL THE ELECTRICAL CABLES OR THE SHEATHS O
3. INFORMATION ON THE LOAD Metal tools very dirty Metal tools very dirty Delicate tools not very dirty Rubber and plastic Delicate tools Glass Tools not very dirty Standard washing Starting a wash cycle a We recommend charging the lower basket first and then the upper b Make sure you have properly closed the door with limited strength c Insert the plug into the socket The power supply is 230V 50 HZ the specification of the socket is 250V 10 DESCRIIPTION OF WASHING Pre wash 50 Wash 70 Rinsing Rinsing Rinsing 70 Drying Pre wash Wash 60 Rinsing Rinsing70 Drying Pre wash Wash 50 Rinsing Rinsing 70 Drying Wash 45 Rinsing Rinsing 60 Drying Wash 40 Rinsing Rinsing Drying Pre wash Wash 60 Rinsing Rinsing70 Drying DETERGENT DURATION MIN PRE WASHING GR 3 15 140 3 15 120 3 15 170 15 75 15 30 3in 1 1pcs 140 d Select the desired program and press the select button of the program e Press and ON OFF button to start the automatic car wash f Press ON OFF at the end of the wash Open the door of the washing tools after waiting for 30 minutes Changes to the program Press and hold the START RESET button for more than 3 seconds to stop washing Press the button to select the program you choose Press the START RESET button to start the wash At the end of the wash cycle ENERGY CONSUMPTION kWh 0 9 0 65 0 5 0 30 0 7 WATER CONSUMPTIO
4. bending or kinking Use the special plastic support that comes with the machine The free end portion of the exhaust pipe can be at a maximum height of 75 cm and must not be immersed in water 7 7 ELECTRICAL CONNECTION Power supply with electrical fuses Only copper cables We recommend the use of delayed action fuse circuit breaker and separate circuit dedicated exclusively to the machine The socket outlet shall be installed in a recessed compartment adjacent Make sure that the plug is accessible after installation After checking that the values of voltage and frequency to the household power supply correspond to those given in the rating plate and that the electrical system is sized for the maximum voltage on the rating plate insert the plug into the outlet with earthing adequate If the electrical socket to which the appliance must be connected is not adequate for the appliance have the socket replaced by a qualified electrician and the use of adapters danger of overheating and burns Before use make sure that this grounding Do not use extension cords or adapters for this washing machine Do not remove for any reason the ground connection of the power cord Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 7 8 SALT D Load the salt into the water softener Unscrew the capo f the container in a counterclockwise direction f 1 placed on the left side inside the machine E Pour salt in the container 250
5. of repair replacement of defective parts or replacement of the equipment during the warranty period the warranty remains unchanged it always starts from the original date of purchase of the unit As nothere reported The Terms and Conditions listed on the commercial documentation sales catalogue in force at the time of purchase remain valid 22 ENVIRONMENTAL CONDITIONS ALLOWED TEMPERATURE HUMIDITY AND ALTITUDE See Paragraph in particolar 23 ELECTROMAGNETIC COMPATIBILITY Install the unit where electromagnetic interference comply with the limits permitted by the rules and with the presence of electric and electronic equipment RADIATION EXPOSURE The appliance is not intended to be used to direct exposure to Non ionizing radiation of the sun being the same to be placed indoor and or repaired X ray radiation microwave radiation laser radiation etc In the event that in the environment where the unit is placed there is a risk of radiation directly on it specific measures to protect exposed areas must be taken by the purchaser USE IN EXPLOSIVE ENVIRONMENT The device cannot be used in any way in the environment where there is a risk of explosion or in a potentially explosive environment IT IS FORBIDDEN TO USE THE EQUIPMENT IN EXPLOSIVE ENVIRONMENTS SUCH OR CONSIDERED Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 ILLUMINATION IN THE WORKPLACE The environment in which the washing machine
6. sprinkles water INSTRUCTIONS FOR USE Make sure that the hydraulic and electrical connections have been properly made by qualified personnel and that the water tap is open Open the door and place the instruments Check that the arm moves freely and sprays water and if necessary remove any obstructions Fill the detergent compartment Close the door Select the desired program using the rotary 3 Press the power button 1 Will turn on the light 2 Press the start button 4 Will turn on the light of operating 5 The machine will stop automatically at the end of washing cycle and 5 and 2 green lights will stay on A short beep will signal the end of the wash cycle Open the door and wait a few minutes before removing tools 11 After downloading the machine remove the filters clean them and put them back in their original position Do not open the door until it has finished the cleaning A To facilitate drying of the instruments at the end of the wash cycle open the machine and wait a few minutes before removing the tools 9 0 POWER EQUIPMENT Starting a wash cycle Ensure that the plug is inserted into the wall outlet Check that the water supply is done with the right pressure Load the instruments see paragraph Add detergent Close the door press the ON OFF button and the light will turn on At this point the cycle starts Press the START RESET button and the program will start in a few seconds Press the
7. 4 STAIN ON TOOLS 1 WATER TOO HARD 1 FOLLOW THE 2 LOW TEMPERATURE MANUFACTURER S INPUT INSTRUCTIONS 3 OVERLOAD THE WASHER 2 DO A WASH CYCLE 4 DETERGENT NON ALONG WITHOUT ADDING CONFORMING DETERGENT BUT THREE 5 LACK OF AID GLASSES OF WHITE 6 EXCESS OF DETERGENT VINEGAR ON THE BOTTOM OF THE WASHER THE MACHINE DOES NOT STOP 1 DIRTY FILTER DOWNLOAD THE WATER AND CLEAN THE FILTER FOAM IN THE BATH NOT SUITABLE USE ONLY DETERGENT DETERGENT RECOMMENDED BY THE 2 RELEASE OF AID MANUFACTURER 2 DRY IMMEDIATELY THE RELEASE OF THE RINSE NORMAL PHENOMENON DURING THE DRYING AND THE DISCHARGE OF WATER VAPOR PASSING THROUGH THE VENT OF CLOSING THE DOOR N Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 14 PRODUCT DETAILS IN ACCORDANCE WITH THE COMMISSION DELEGATED REGULATION EU NO 1059 2010 Free standing Energy efficiency class new 2010 30 EC Annual energy consumption kWh New 2010 30 EC9 1 Energy consumption kWh Water consumption in liters year New 2010 30 EC 2 Reference program 3 Efficiency class Drying Total duration of a cycle time of reference program min Noise level dB A re 1 pW sound power Consume energetic in left on left on Consume energetic in left on off mode Free standing A 174 0 62 1960 Eco A 140 55 0 3 W 0 2W 1 Power consumption in kW h per year based on 280 standard cleaning cycles wi
8. 5661 detergent powder for the instruments sterilized Degreasing suspending descaling and sequestrant Multipurpose and non foaming Dosage 7 10 grams in door A CLEANEK is a medical device meets the requirements on the DM Directive 93 42 EEC and subsequent amendments Directive EC 47 2007 RINSEOFF AB ART 5662 liquid for rinsing which helps to reduce drying time it meets the need for lubrication of joints and mechanical joints making it shiny and stain preventing oxidative effects Dosage fill the rinse aid cover RINSEOFF AB is a medical device meets the requirements on the DM Directive 93 42 EEC and subsequent amendments Directive EC 47 2007 Warning Keep the soap out of reach of children Avoid contact with skin Use only detergents specially formulated for washing machine Do not overuse detergent We suggest using readily soluble detergent ren Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 O A PREPARATION OF INSTRUMENTS TO WASH Tools with sharp points must be positioned so as not to damage the parts of the machine door Do not put plastic or wooden tools if they are not covered by the mark of temperature or equivalent Place any containers with the large down Do not overload the machine Remove any residue from the instruments before insert them into the machine preferably use a tank of disinfection Check that the arm rotates freely
9. DELAY START button to set the delayed start This washing machine can be programmed in advance by choosing from 3 6 9 and 12 hours If you wish to cancel the delayed start just press the button until it no longer appears selected time X S X S X S X S Cancellation or change the setting of a wash cycle Press and hold the START RESET button for at least 3 seconds the current program will be erased At this point a new program can be selected Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 The end of the wash cycle At the end of the wash cycle the buzzer of the washing machine will beep for eight seconds then stops Switch off the appliance using the ON OFF open the door and wait a few minutes before removing tools 30 minutes is ideal If you have forgotten to add tools You can add instruments at any time Open the door slightly to stop the washing After the spray arm has stopped fully open the door Add the tools forgotten Close the door and the washing will start after ten seconds from closing completely Warning It is dangerous to open the door with the washing machine on as it may come out boiling water 20 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 10 TABLE OF PROGRAMS OF WASHING WASHING MACHINE MOD MINI WASH PROGRAMS 1 INTENSIVE 2 NORMAL EN50242 3 ECO 4 GLASS 5 RAPID 6 3in1
10. F THE ELECTRICAL INSTALLATION 14 DO NOT START BEFORE CHECKING DIRECTLY AND VISUALLY THAT IN OR ON THE MACHINERY THERE IS NO FOREIGN BODY 15 IN ANY SPECIFIC CIRCUMSTANCES ALWAYS USE APPROPRIATE PROTECTIVE CLOTHING OR TOOLS 16 NEVER INSERT THE HANDS OR OTHER PARTS OF THE BODY IN COMPONENTS NOT PERFECTLY FIXED OR IN PARTS NOT COMPLETELY VISIBLE FROM THE PERSON WHO IS OPERATING 17 KEEP THIS U M M ALWAYS AT HAND AND AT DISPOSAL OF THE ENABLED USER AND DURING INSTALLATION AND OR MORE VISITS AND USE 18 THE U M M DUPLICATION IS RECOMMENDED AUTHORIZED BY THE MANUFACTURER FOR THE INTERNAL USE ONLY AND IT IS AVAILABLE FOR THE PERSONAL AND ENABLED USER KEEP THEN THE ORIGINAL COPY IN A SAFE AND EASY AVAILABILITY DURING THE OPERATION OF THE MACHINE THE SURVEILLANCE OPERATOR MUST BE CONTINUED ANY TOOLS FOR THE OPENING OF ELECTRICAL PANEL OR PROTECTIONS MUST BE STORED AND OR ACCESS ONLY TO AUTHORIZED PERSONS AND EDUCATED IT IS OUT OF LAW LEAVE THESE TOOLS AND ACCESSIBLE TO ALL PACKING Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 2 1 WARRANTIES AND LIABILITY The MANUFACTURER ASSUMES NO LIABILITY FOR DAMAGES CAUSED ON THEMACHINE ON THINGS ANIMALS AND OR PERSONS MAKING ANY KIND OFWARRANTY INVALIDATE IMMEDIATELY IF e THE INSTALLATION OF THE APPLIANCE IS NOT DONE BY QUALIFIED e PERSONNEL IN ACCORDANCE WITH THE RULES AND MAY BE REPORTED ASIN THE DECLARATION OF CONFORMITY e THE START UP OF THE EQU
11. GERS AND SIGNALS To highlight to the user to those exposed and to the authorized personnel all the residual risks to which attention must be paid it was decided to affix to the machine standardized symbols highlighted in the following pages The dangers to which it could not apply a total protection because it would make the machine difficult to use inhibiting their intended use are as follows A 1 Electrical dangers inside the control panel or any derivations of the unit Thermal dangers resulting from the contact of the user s arms when the respective electrical 2 resistance is operating 5 FAILURES MALFUNCTIONS OR OTHER INCONVENIENCES In case of failures malfunctions or other problems not covered in this U M M call the manufacturer directly The address is as follows REVERBERI ARNALDO S R L Via Don L Sturzo 6 42021 BARCO di Bibbiano RE ITALIA Tel 39 0 522 875159 Fax 39 0 522 875579 e mail reverberi_a libero it Any work on the machine determined by a malfunction must necessarily be performed by qualified personnel In case of replacements of equipment parts use original spare parts to avoid causing A variations in performance and or reduce the level of safety Each cleaning checking and or maintenance must be performed by authorized personnel and authorized to do so in compliance with the requirements given in this U M M 12 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014
12. IPMENT IS NOT PERFORMED BY A QUALIFIED e QUALIFIED PERSONNEL AND OR USER NOT COMPLY WITH THE INSTRUCTIONS GIVEN IN THIS USER AND MAINTENANCE MANUAL OR AS RESULT OF ANY OPERATION NO SPECIFICALLY DESCRIBED e VERIFY CAREFULLY DURING THE READING OF U M M THE CORRESPONDENCE WITH THE PARTS OF THE EQUIPMENT CHECKING e THE PARTS HAVE NOT BEEN DAMAGED DURING THE TRANSPORTATION AND HAVE BEEN DELIVERED INTEGRA e THERE ARE ALL THE SAFETY SYMBOLS DO NOT PROCEED TO USE THE WASHING MACHINE IF ALL ITEMS DESCRIBED ABOVE DO NOT EXIST e THE MANUFACTURER ASSUMES NO RESPONSABILITY FOR DAMAGES CAUSED TO THE SAME DEVICE ON PEOPLE ANIMALS AND OR PROPERTY IF ANY ANOMALIES IS NOT REPORTED WITHIN 30 DAYS OF RECEIPT OF GOOD TO MANUFACTURER IN THESE CASES ANY TYPE OF WARRANTY BECOME INVALID AUTOMATICALLY e TO COMPLY WITH THE TRACEABILITY OF THE WASHING MACHINE ANY CHANGE OF ADDRESS OF THE SAME MACHINE MUST BE COMMUNICATED TO THE MANUFACTURER DEALER ANY CHANGES MADE ON ITS DEVICE or safety devices WHICH MAY AFFECT THE FUNCTIONS PROVIDED BY THE MANUFACTURER and the risks of the risk analysis included in the Technical Construction File WILL BE FULL RESPONSIBILITY OF THE RUN AS CHANGE IS MEANT ALSO THE FAILURE OF THE INSTRUCTIONS REPRESENTATIONS AND EFFORT NONCONFORMING AND THE USE OF PARTS NOT ORIGINAL Any change even if not substantial must be communicated by registered post and also approved by the MANUFACTURER THAT will approve THE CHANGES on
13. N IN LT 11 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 After washing the time display will flash for 8 seconds while the buzzer sounds After washing delayed you will not hear any beep but you can only see the time display flashes 11 CLEANING AND MAINTENANCE Provide regular cleaning of filters to remove providing the three parts that are on the bottom of the wash tools Wash with water dry and reassemble them as before To clean the outer cabinet use a soft non abrasive detergent 22 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 12 TECHNICAL FEATURES MAIN FEATURES ENERGY EFFICIENCY CLASS NEW 2010 30 EC A GENERAL FEATURES BUILT IN FREE INSTALLATION FREE INSTALLATION TECHNICAL FEATURES END OF CYCLE INDICATOR YES WITH BUZZER DRYING SYSTEM CONDENSER SALT WARNING LIGHT YES ENERGY LABEL WATER CONSUMPTION I 7 TOTAL ENERGY CONSUMPTION PER YEAR kWh 174 TOTAL DURATION OF A CYCLE TIME OF REFERENCE PROGRAM 140 min DIMENSIONS WIDTH mm 550 NET WEIGHT kg 23 5 N C2 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 SPECIAL FEATURES AND BUTTONS PROGRAM SELECTION YES START YES PROGRAMS SELECTION YES LOW RINSE YES OPERATION YES PROGRAMS LIST NORMAL YES GLASS YES 3IN1 YES N js Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 13 ANOMALIES AND
14. Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 reverberi OPERATING AND MAINTENANCE MANUAL Language English INSTRUMENTS WASHER MINI WASH M9016 2 6 WASHING PROGRAMS A ENERGY EFFICIENCY 3 WASHING TEMPERATURE Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 EA AN A lt THE MACHINE IS FOR PROFESSIONAL USE ONLY gt lt THE USE IS PERMITTED ONLY QUALIFIED PERSONNEL TO DO gt lt CONTACT THE QUALIFIED INSTALLER FOR THE IMPLEMENTATION OF THEEQUIPMENT gt THE MACHINE CANNOT BE PUT IN WORK IN A ENVIRONMENT AT RISK OF EXPLOSION gt Read carefully the instructions when buying the machine and before storing installing using it This Manual that provides useful information regarding the safety during the IMPLEMENTATION OF THE EQUIPMENT INSTALLATION USE etc is part of the product itself and it must be delivered to the user who has to store and carefully read it before starting each step of the service provided by the machine Do not remove tear or rewrite neither partly this Manual Keep the Manual in areas protected from moisture and heat for future reference This Manual contains the CE Declaration of conformity THE MACHINE MUST BE INSTALLED AND USED ONLY ACCORDING TO THE RULES LAID DOWN BY THE MANUAL U M M NOTE Images designs and texts included in this manual are producer s property All right
15. SOLUTIONS ANOMALIES THE MACHINE DOES NOT START THE DRAIN PUMP DOES NOT STOP TOOLS NOT CLEAN TOOLS NOT DRY POSSIBLE CAUSES 1 POWERIS NOT BEING 2 THE DOORIS NOT CLOSED GOOD 3 THE MACHINE is NOT ON A FLAT SURFACE 4 BLOWN FUSE OR CIRCUIT BREAKERS IN ACTION 5 THE WATER PRESSURE IS TOO LOW 1 RELEASE OF WATER LOAD WRONG 2 THE BOOM SPRAYING WATER DOES NOT ROTATE FREELY 3 INADEQUATE OR NOT SUITABLE DETERGENT 4 DIRTY INSTRUMENTS INCORPORATED 5 BENT PIPE WATER LOAD 6 IMPROPER INSTALLATION 1 THE RINSE AGENT DISPENSER is EMPTY SOLUTIONS 1 CHECK THE POWER AND THAT THE SWITCH IS ON WELL SHUT THE DOOR PUT UP IN THE MACHINE REPLACE THE FUSE OR RESET THE CIRCUIT BRAKERS REMOVE ANY OTHER APPLIANCE THAT AGREE TO THE SAME CIRCUIT WITH WASHER MAKE SURE THE WATER SUPPLY IS CONNECTED PROPERLY AND THE TAP IS OPEN THE SYSTEM WAS DESIGNED TO DETECT LEAKS WATER IN THIS CASE THE PUMP STOPS AND IS ACTIVATED THE DRAIN PUMP ARRANGE THE LOAD INA WAY THAT ALL SPLATTER INTO ALL SURFACES DO NOT OVERLOAD THE MACHINE CHECK THE BOOM SPRAYING WATER ORDER NOTHING OBSTACLES HIS DIRECTION USE MORE DETERGENT DO NOT USE DETERGENT OR HARD GRAINY ONLY USE DETERGENT WASHING MACHINE CLEAN WITH CARE INSTRUMENTS BEFORE YOU LOAD THE MACHINE SPREAD THE GOOD WATER INLET HOSE REVIEW THE INSTALLATION FILL N Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 201
16. aging Use a reliable transporter Any intervention on determined by a malfunction must mandatory be performed by qualified personnel to do so variations in performance and or reduce the level of safety Each cleaning checking and or maintenance must be performed by authorized personnel and authorized to do so in accordance with the requirements described in this U M M case of replacements of equipment parts use original spare parts to avoid causing 4 PREVENTIVE EDUCATION TITLE USER OPERATOR The user who has the responsibility for operation of the unit must be educated and trained person in advance by the Employer or his guardian that person must MANDATORY read UNDERSTAND all instructions in this MUM The manufacturer is not liable for any direct or indirect damages caused by people who have used the device without having received proper education and qualifications relevant to the conduct thereof and in which they did accordingly misuse 4 0 DEVICES FOR PERSONAL PROTECTION TO BE USED TO PREVENT THE ONSET OF RESIDUAL RISKS According to legal requirements dictated by the regulations on this subject it is the duty of Head of Hygiene and Safety to analyse the potential risks people are exposed to and to wear appropriate Personal Protective Equipment P P E in the Studio where the equipment is installed Regardless of the risk analysis of Hygiene and Safety Manager in all cases mentioned in this Section are sh
17. aussscssstenscccentscessteseesccausvacscsvessssdevivonsstesssssessiveescousssssesideon dese 14 7 0 METHOD OF CONNECTING FITTINGS GUIDELINES FOR WATER SUPPLY 14 7 1 DISCONNECT THE FITTING OF SAFETY 14 7 2 DISCONNECT THE WASHING MACHINE 15 7 3 COLD WATER CONNECTION 15 7 4 HOT WATER CONNECTION 15 7 5 POSITIONING OF THE WASHER 15 7 6 CONNECTING THE DRAIN PIPES 15 7 7 ELECTRICAL CONNECTION 15 7 8 SALT 16 7 9 RINSE AID 16 7 10 DETERGENT 17 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 8 PREPARATION OF INSTRUMENTS TO WASH 19 9 INSTRWGTIONSIEORAUSE rsrcasrrrsreoisicaroniseninenizenizanisesazanizeoneanisesizanesesiazassesasaniseonzaaecesazanezioneareseonzio 19 9 0 POWER EQUIPMENT 19 10 TABLE OF PROGRAMS OF 21 11 CLEANING AND MAINTENANCE cscrrrrsseserereseceeeeeseceenesseceeeesseceeezeseceeeesseceeeneseceenesseceeeneseceeeneseceenese 22 12 TECHNICAL FEATURES serrrrssecrrrresecrereezeceeezezeceeezeneceeezaneceeseaneceeezeseceeezaseceeseszeceeezaseceenesseceeneeseceenese 23 13 ANOMALIES AND 0 0 25 14 PRODUCT IN ACCORDANCE WITH THE COMMISSION DELEGATED REGULATION EU NO 1059 2010 27 15 WARRANTY CERTIFICATION vrrrerecrrrresecrereezeceeezeneceeeeenece
18. e original operation use replacement parts other than original alter the electrical system and safety devices connected to them NOT TO COMPLY WITH THE INSTRUCTIONS THE OBLIGATIONS AND PROHIBITIONS CONTAINED IN THIS MANUAL AND ON THE UNIT ITSELF 3 RECOMMENDATIONS AND GENERAL SAFETY The user is responsible for installation proper use and maintenance of the washing machine in accordance with the instructions in this manual If necessary contact your local Technical Support The washing machine should not be used with flammable gases or vapors For the wash of materials carefully follow the instructions provided by the manufacturer of the materials Do not exceed load limits specified in this manual Do not remove the identification number or any other labels from the serial number or other washing machine To prevent electrical short circuits do not spill water or other liquids on the machine Turn off the machine and unplug the power cord before inspecting make operations maintenance or repairs of the washing machine Never turn off the machine with the door closed Keep the original packaging carefully for any transport The repairs should be made by individuals authorized by the manufacturer and using only original parts 10 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 case of transport The machine should be empty Use the original packaging or other suitable pack
19. eezaneceeneszeceeezaseceeeeazeceeezaneceenesseceeneszeceenese 28 16 DECLARATION OFINSTALLATION seoscccvreesrerizanizaranenicarazanicazzzanioorananiossunenioorizanioazioeezeoresaeioozenizioneezii 29 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 1 INTRODUCTION We thank you for choosing a REVERBERI machine The User and Maintenance Manual U M M has been realized in order to provide general knowledge of the machine and to give the transport use and maintenance instructions and all the necessary details for the installation for the correct use and for the proper functioning We ask you kindly to CAREFULLY read the manual BEFORE CARRYING OUT ANY OPERATION ON THE MACHINE In case you need another copy of the Use and Maintenance Manual U M M you are invited to forward your motivated request to the CONSTRUCTOR quoting the serial number on the title of this post or on the name plate on the back of the machine 1 0 PURPOSE OF THE USER MANUAL AND MAINTENANCE The following Manual aims to provide user all the information about Washing machine in order to warrant the correct installation the optimal use a safe and reliable functioning the requirements for proper and regular maintenance and for the periodic replacement operations of the components SOS 1 1 USER S PROFILE Two kinds of profiles can use the washing machine and have to read carefully this Manual The Administrator The administrator i
20. fer to the minimum necessary to ensure efficiency safety and duration of the equipment in normal working conditions Surveillance will still be constant and will act promptly in cases of anomalies All our equipment are subject to continuous technological development We must therefore from time to time subject to the possibility of making changes regarding the construction and endowment which can modify the operating features The electrical system as well as the continuity of the protective circuit has been tested by REVERBERI at the factory so it is general and guaranteed perfect and functioning Any damage caused by the buyer for incorrect links automatically excludes any warranty on the unit The position of the CE plaque is visible EC 2 0 CAUTIONS WARNINGS PROHIBITIONS 1 LIQUIDS OR DUSTSHOULD NOT FALL ENTER INTO THE APPARATUS SEEK TO MAKE INSTALLATION THAT AVOID THESE PROBLEMS 2 FLAMMABLE LIQUIDS OR POWDERS SHOULD NOT BE USED NEAR THE MACHINERY 3 IT IS FORBIDDEN TO EVERYONE AND OR TO OPERATORSWITH HEART DISORDERS AND PACEMAKERS TO APPROACH THE MACHINERY WITHOUT FIRST CONSULTING THE DOCTOR 6 pum Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 4 BEFORE USING THE DEVICE IT IS NECESSARY TO KNOW ALL THE OPERATIONS AND CONTROL DEVICES LEARNING CONCEPTS OF THIS SHOULD BE MANDATORY BEFORE BEGINNING PEOPLE NOT ATTACHED AND WITHOUTTHE APPROPRIATE CONCEPTS ARE NOT ALLOW USING THE MACHINE 5
21. form yourself about the local separate collection system for electrical and electronic products Comply with local rules and do not dispose of your old products with your normal household waste Proper disposal of the product will help prevent potential negative consequences for the man s health and for the environment 2 GENERAL WARNINGS THE MANUFACTURER DO NOT PROVIDE WARRANTIES ABOUT THE SUITABILITY OF THE TECHNICAL LEGAL ROOM WHERE THE EQUIPMENT IS INSTALLED AND ALL THE SUPPORT SERVICES AT THE SAME ALTHOUGH THE U M M OFFERS IMPORTANT INFORMATION FOR A PROPER INSTALLATION REGARDING THIS ASPECT THE USER IS RECOMMENDED TO USE THE ADVICE OF QUALIFIED PERSONNEL EXPERT IN THE FIELD FOR THE RESPECT OF EVENTUAL LAWS AND OR REGULATIONS TOO DO NOT ALLOW ANYONE TO USE THE MACHINE WITHOUT FIRST e READ AND UNDERSTAND ALL THE INDICATIONS INCLUDED IN THE U M M e RECEIVE SUITABLE INSTRUCTION FOR THE SAME CONDUCTION BY A PERSON AUTHORIZED THE MACHINE IS BUILT IN COMPLIANCE WITH CURRENT STANDARDS PLEASE BEFORE PROCEEDING WITH THE INSTALLATION USE MAINTENANCE AND REPARATION AND RELATED READ CAREFULLY THIS USER AND MAINTENANCE MANUAL BECAUSE IT CONTAINS ALL THE NECESSARY INFORMATION FOR A PROPER USE AND OPERATION DESIGNED TO PREVENT ACCIDENTS THIS U M M MUST BE CONSIDERED PART OF THE PRODUCT ITSELF AND IT MUST REMAIN PART OF IT FOR ALL THE PRODUCT LIFE The frequencies of monitoring and maintenance prescribed by the U M M re
22. gr f 2 F Add water into salt container until a small amount of water comes out is very important when using the washer for the first time G Carefully screw the cap Important note Add the salt before starting the wash cycle to prevent corrosion Only use salt for machine 79 RINSE AID Add the rinse aid unscrewing the cap in a counterclockwise direction f 1 Fill the rinse aid dispenser to fill it up f 2 Screw the cap clockwise f 3 To prevent stains on the instruments and reduce the drying time always use the rinse aid Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 7 10 DETERGENT Open the door by pressing the key f 1 Put the detergent up to the filling line f 2 Use the detergent compartment A to fill the normal washing detergent Use the detergent compartment B to fill the pre wash detergent At the end of each wash check that the compartment of detergent is empty Qv E ONS DETERGENT CLEANEK 2 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 CLEANEK 1 ART 5660 enzyme powder for the instruments to be sterilized Degreasing suspending descaling and sequestrant Multipurpose and non foaming Dosage 7 10 grams in door B CLEANEK1 is a medical device meets the requirements on the DM Directive 93 42 EEC and subsequent amendments Directive EC 47 2007 CLEANEK 2 ART
23. is installed must meet the requirements listed on the Directive 89 654 EEC concerning the workplace and the requirements of the RULES FORCE THE INSTALLATION SITE Proper lighting can in some cases avoid limit an injury to the operator 2 4 REQUIREMENTS OF THE LOCAL WHERE THE EQUIPMENT IS INSTALLED The local should be free of debris and or residues of various kinds of flammable or potentially dangerous operation provide a specific room for washing away from the patient have doors accesses appropriate to the size of the machine ensure a suitable floor for the mass flow of the machine ensure a perfectly level floor be free at the area of installation strong drafts or substantial temperature changes ensure good ventilation and air exchange with the provision of specific natural ventilation openings 25 USE NOT PERMITTED It is not allowed THE USE of the machine if you have not INSTALLED in accordance with APPLICABLE RULES and BY AUTHORIZED PERSONNEL the use of the appliance by USERS not authorized by the superior role or employer the use of the appliance by USERS not trained to manage it the use the equipment for purposes other than those expected and stated in the Declaration of Conformity the use the equipment in environments with explosive atmosphere or where there are similar risks elaborate or otherwise alter the unit cycles and performance USe or use accessories other than th
24. ly if such amendment shall not constitute implementations of risk analysis AND THE risks of the machine Any change made without notice to the MANUFACTURER will constitute CANCELLATION OF the CE Declaration of Conformity making void any warranty and guarantee by the same The manufacturer is not responsible for the placement of a protection mechanisms against overcurrent for power conductors of the electrical equipment which must be placed upstream of the apparatus and duly reported the installation of power plug to be placed between the electrical panel and the electrical appliance in place of the existing installation WARRANTIES CONDITIONS This appliance is guaranteed for one year 12 months from the date of purchase on the whole territory of the European Union the date of the delivery note invoice will be the authentication The device is used for professional use During this period the manufacturer will repair or replace for free those pieces that at its own sole discretion were to be originally defective with only the reimbursement of travel expenses incurred by the technicians of the Service Centre at doorstep or totally free if the equipment is delivered to BARCO di Bibbiano RE Defective parts replaced become the property of the manufacturer If the defect is not repaired the manufacturer may avoid the termination of the contract by the customer by offering free replacement of the property Are no
25. own the MANDATORY P P E that the exposed personnel must use while approaching the machine The use of additional D P I is at the discretion of the Head of the Hygiene and Safety in the Studio where the equipment is installed Use 1 safety shoes to ensure a sufficient level of electrical mechanical isolation 2 flame retardant protective clothing 3 appropriate gloves POWER SUPPLY DIRECTLY FROM THE GENERAL SWITCH BUT STOP THE CONTROL IN NORMAL CONDITION OPERATIONS NEVER STOP THE DEVICE REMOVING THE PANEL FIRST EMERGENCY STOP WASHING MACHINE In case of emergency there is a need to stop THE equipment the operator must take prompt action on the connection socket plug off grabbing the plug WITHOUT pulling the cable In this regard it should be noted that the plug must always be free of any material or furniture and always visible 11 Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 41 CONDUCT OF MACHINE BY USER The user s tasks are monitor the operation of the appliance acting promptly in case of malfunctions check the constancy of performance and integrity of the devices used and promptly shut down the device in case of malfunctions O It is FORBIDDEN to leave the unit without first having switched it off at the end of the work The intervention of the user will always be subject to compliance with the symbols placed AN on the machine and the requirements dictated by this U M M RESIDUAL DAN
26. release This helps decrease the water pressure and to protect people and the room from violent splashing water Unscrew the safety of the tap Hn Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 7 2 DISCONNECT THE WASHING MACHINE e Remove the power cord from the wall outlet e Disconnect the connector Unicouple from the tap adapter Note When the motor stops after the final rinse the connector Unicouple can be disconnected and stored 7 3 COLD WATER CONNECTION Connect the connection for cold water supply to a connector Make sure it is secure If the water pipes are new or have not been used for a long time let the water run to make sure it is clean and free of debris Otherwise you run the risk of blocking the ingress of water and damage to the appliance 74 HOT WATER CONNECTION The machine can also be connected to the hot water pipes centralized system heating provided it does not exceed a temperature of 60 In this case the washing cycle will be shortened by about 15 minutes and the washing efficiency slightly reduced 7 5 POSITIONING OF THE WASHER The rear part of the machine should be resting on the wall The machine is equipped with pipes for the water supply and drain fittings that can be positioned to the left or right side for easier installation 7 6 CONNECTING THE DRAIN PIPES Insert the drain hose into a drain pipe with a minimum diameter of 4 cm or let it flow into the sink and avoid
27. s repaired modified or tampered with by the purchaser or unauthorized third parties If the customer does not perform the proper and constant maintenance on this manual If the buyer does not talk to the dealer or authorized service centre After 12 months from date of purchase proven by the sales document If the customer delays or suspends payments If the equipment shows damages caused by exposure to fire spilled liquids natural disasters falls however causes not attributable to manufacturing defects If the guarantee has been not duly completed signed and returned in a timely manner If the customer makes improper use of the equipment does not administer the ordinary maintenance or neglects elements principles of good maintenance N Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 16 DECLARATION OF INSTALLATION WARRANTY CERTIFICATE AND STATEMENT OF SERVICE INSTALLATION INSTALLATION DATE raider Technical course of installation repair and maintenance The technician who has carried out the installation of the washing machine has previously attended the technical course and has been authorized by the manufacturer s for the installation and repair of such equipment Installation according to the manual of use and maintenance The technician who has carried out the installation of the washing machine claims to have complied with all conditions that allow the correct installation of the device according to the
28. s reserved It is forbidden even partial reproduction of drawings images and texts The manufacturer reserves the right to alter without notice the info in this manual Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 1 JINTRODUCTION 3 2 2 3 o stas RANA AA iii iii 5 1 0 PURPOSE OF THE USER MANUAL AND MAINTENANCE 5 1 1 USER S PROFILE 1 2 EXPECTED USAGE 5 2 GENERAL WARNINGS eene nnne nnn nn nn nn nn nnn nn nn nnno sn sn so sn so sn sn sn so sn sn so so O 2 0 CAUTIONS WARNINGS PROHIBITIONS 6 2 1 WARRANTIES AND LIABILITY 8 2 2 ENVIRONMENTAL CONDITIONS ALLOWED 9 2 3 ELECTROMAGNETIC COMPATIBILITY 9 2 4 REQUIREMENTS OF THE LOCAL WHERE THE EQUIPMENT IS INSTALLED 10 2 5 USE NOT PERMITTED 10 3 RECOMMENDATIONS AND GENERAL SAFETY ssssssesssesensnsssssesssssecnensssssesssssecsenssssssssssssssecsssssesseses LO 4 PREVENTIVE EDUCATION TITLE USER 11 4 0 DEVICES FOR PERSONAL PROTECTION 11 TO BE USED TO PREVENT THE ONSET OF RESIDUAL RISKS 11 4 1 CONDUCT OF MACHINE BY USER 12 5 FAILURES MALFUNCTIONS OR OTHER INCONVENIENCES eene eere 12 6 MACHINE DESCRIPTION ssssssessssssensnsssessssseseenensesssssssessenenssssssssssssesansssssssssssscnanssssssssssssesecsssssesseses 13 6 0 PUSH BUTTON CONTROLS 13 7 INSTALLATION INSTRUCTIONS iisscsscssiscccstiesessc
29. s the responsible for the clinic or doctor s office or rather the person responsible for the protocol of hygiene and washing process The administrator is also responsible for the OPERATORS training and for the proper operation and maintenance of the equipment Must have adequate training for all operations to be performed and for safe use The Operators The operators are those who use the washing machine according to the instructions received from the ADMINISTRATOR 1 2 EXPECTED USAGE The Reverberi washing machine are used for cleaning tools in general medicine studios dental studios veterinary studios and facilities for personal hygiene and beauty treatment These washer can be also used by beauticians tattoo artists body piercers hair stylist and podiatrist Do not use the machine for purposes other than those for which it was created It is important to ensure that the value of ground resistance is efficient and well coordinated with the electrical protections of the implant in order to avoid electrical interferences to the washer Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 CAUTION IT IDENTIFIES A SOURCE OF HEAT THERE MAY BE AN UNSAFE TEMPERATURE CAUTION IT IDENTIFIES A GENERIC DANGER THERE MAY BE A DANGEROUS SITUATION PB IT IDENTIFIES THE PROTECTIVE EARTH TERMINAL This symbol indicates that the product is covered by 2002 96 CE European Directive Please in
30. t covered by the warranty the damaged parts for transport shock for bad or improper installation use through neglect or misuse tampering by unauthorized persons damages weather or other natural events or other causes not dependent on REVERBERI supplies and or subjected to wear low Further or other claims for damages in addition to those provided by law are excluded 8 sea Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 The manufacturer will charge the cost of repair if the returned product is not covered under warranty Interventions for alleged defects or casual checking shall be borne by the customer Any repair of transport to and from the Technical Assistance Centre of BARCO di Bibbiano RE is done at the expense and responsibility of the customer The technical staff when called to repair will be sent in time only compatible with the business needs of the manufacturer Any use bans imposed by the Health Authority or by other competent bodies do not entitle the buyer to demand the surrender or to ask for damages Any difference on the exterior color or color effects of the various parts making up the unit are not considered defects the differences may be e g due to the manual workers The inability to ensure substitutability of parts that make up the set with pieces from standard freshmen supplies purchased specifically different and not as a replacement is not considered a defect In case
31. th cold water and consumption of energy efficient ways Actual energy consumption will depend on how the appliance is used 2 Consumption of water W liters year based on 280 standard cleaning cycles Actual energy consumption will depend on how the appliance is used 3 Program is the standard wash program to which the information relates to the label this program is suitable for washing delicate instruments and that is the most efficient program in terms of combined energy and water M N Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 15 WARRANTY CERTIFICATION reverberi WARRANTY CERTIFICATION Hereby certify the correct construction of the equipment The device that within the warranty period manifests irregularities in the running for manufacturing defects will be repaired at the sole discretion of the house Return the attached coupon duly stamped and signed by the technician who took part to the installation course In case of dispute will be valid the delivery note sale invoice or delivery invoice The electric and electronic parts screws are guaranteed for a period of 12 months The warranty is limited to the replacement or refurbishment of spare parts or parts that prove defective manufacturing excluding expenses or call Any particular replaced must be returned prepaid Any piece that is not returned will be billed to the payer e THE WARRANTY IS NO MORE VALID If the equipment i
32. use and installation manual Instruction to the user functioning and maintenance The technician further declares to have properly instructed the user on the functioning of the machine with the support of the instruction manual Instructions to the user on the warranty conditions The technician has also shown the warranty conditions as described in the use and maintenance manual Warranty form The technician declares to have attached to this form the warranty model which has been carefully filled in WARRANTY CERTIFICATION reverber EQUIPMENT The undersigned dealer certifies that the warranty conditions have been read and that the machine has been delivered and operated in accordance with the provisions of the manufacturer Installation AddIeS8 edere Mee redo Post Code B E COUNTY STAMP AND SIGNATURE OF THE DEALER STAMP AND SIGNATURE OF THE DOCTOR MANAGER To be completed by the technician who has made the installation of the machine Copy for the medical Nuova LAVASTRUMENTI manuale di istruzioni GB Rev 01 20 02 2014 Art No 770 500 EAN 4 004 470 770 506 W H
Download Pdf Manuals
Related Search