EV BM1012(E) 网站版
Contents
1. 7 114 mm 4 5 327 94 12 91 284 5 mm 11 2 308 6 mm 12 1 p mm 6 9 3 LIGHTING INSTALLATION LAMP HOOK oR Pa SAFETY SAFETY RING CORD PICTURE ONE PICTURE TWO The lighting can be hanged on the high place with using the lamp hooks as showed in picture 1 Use the safety cord provided to pass through the bottom safe ring and hang it as a second safety fixing Thelighting also can be used on the ground as showed in picture 2 Note Ensure support loading ability at least 10 times more than product weight and make sure lighting be firmly installed Thelighting must be installed by the qualified personnel Please install it at the place where no one goes through 4 4 POWER SUPPLY CONTROL SIGNAL CONNECTIONS Make the XLR signal line connect with the lighting one port connects with the output port of lighting another one connects with the input port of another lighting Due to the output and input of the lighting keep connecting all the time so the DMX circuit still can be keep connecting when the power of certain unit occurs turn off XLR signal line only can be used in series connection pattern the amount of the lighting can not be more than 32 PCS not available in parallel connection pattern Must add a signal amplifier if the length of signal line exceeds 60M between controller and lighting or between two li2. 3 Dimmer 4 Use menu setting dimmer Reset Cat least 5S EV LIGHT GUANGZHOU CO LTD ADD EV INDUSTRIAL PARK 8 CHUANGYE ROAD TAIPING DEVELOPMENT ZONE GUANGZHOU TEL 86 20 37929678 FAX 86 20 37929298 WEBSITE Http www evlightpro com
3. EV LIGHT EV BM1012 Appearance patent No 201330085957 7 USER MANUAL Please read it carefully INDEX 1 lt Ja 2 TECHNICAL PARAMETER SNR VI RE TEM i LIGHTING INSTALLATION M 4 POWER SUPPLY CONTROL SIGNAL CONNECTIONS 5 5 OPERATION na ein an oes REN ERE OH ELAEER OK EP ENU EE Bs 6 CONTRL PANEL CR 275 T NT nia f voett t EE 8 8 TROUBLESHOOTING eere nennen nennen nnn nnne nennen nennen nnns 8 9 DMX PROTOCOL 9 ACCESSORIES These items are packed together with the lighting please check Name Quantity Unit Remark This manual 1 Pc The power cord 1 Pc 1 SAFETY GUIDELINE Please keep this manual in a safe place for further reference Please make sure they also have this user manual if you sell this lighting to other users Every unit is packed properly by the manufacturer Please operate this lighting according to the user manual Any damage caused by improper use will not be assumed by the manufacturer When receiving the lighting please dispose the carton check and inspect there is any damage or not Should there be any damage caused by transportation do not use the lighting and consult your dealer or the manufacturer This lighting can be used indoors P20 The lighting is only intend
4. ed for installation and operation by qualified personnel Do not mount the lighting directly onto inflammable surface Ensure power supply voltage correspond to device requirements before running It is essential that each lighting is correctly earthed and that electrical installation conforms to all relevant standards When the lighting is hanged to a high place please use a safety cord provided to pass through the lighting handles as a secondary safety fixing for safety seasons For details refer to LIGHTING INSTALLATION section Avoid direct exposure to the light from the lamp specially for people with epilepsy The light is harmful to eyes Donot project the beam onto inflammable surfaces The minimum distance between the lighting and irradiated object should be 1 m Exterior surface temperature of the lighting will be 65 C when working please do not touch it with bare hands To prevent electric shocking please do not touch the power cord when the lighting is running Never let the power cord mix with other cables TheLED lens should be changed if deeply scratched or cracked There is no user serviceable parts inside the lighting Before using the device please check whether the covers or housing are well installed or not and whether the screws are installed firmly or not Do not open the housing and never operate the lighting with the covers removed Always disconnect a lighting
5. from the power supply when the device is not in use or before cleaning it or before attempting any maintenance work Electrical connection must only be carried out by qualified personnel Please use the original packing material for second transportation f you have any questions or suggestions please do not hesitate to consult your dealer or factory 2 TECHNICAL PARAMETER Input Voltage AC100V AC240V 50 60HZ Power Consumption 135W Lamp Specifications 12 pcs four in one RGBW CREE 10W LED rated life 50000 hours Lens Angle 8 Spot Angle 15 Color RGBW linear color mixing Color Temperature color cast calibration setting color temperature output inside device Dimmer 0 100 linearly dimming 5 types dimmer modes smooth dimming flicker free Shutter independent electronic strobe Control Mode Standard DMX512 3 pin interfaces 4 channel modes Master slave mode no need to set up the master and slave manually will receive the main engine data automatically 5 auto running modes rainbow channel and rainbow effect Other Functions Self programming function 5 chases each chase has 20 scenes fade function Lighting setting data self programming data can be downloaded each other Temperature Control Protection both of lamp holder and base have temperature control protection Waterproof Grade 1 20 Work Environment Temperature 20 C 40 C Net Weight 5 6Kg DIMENSION
6. ghtings In the controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator The DMX terminator is simply a connector with a resistor about 1200 OHM connected across pins 2 and of the Canon plug please see the picture in the right It can prevent the noise and reflection caused by DMX EN 512 signal during transmission The transmission speed of DMX 512 signal is very quick It will affect the signal transmission if any damage of the signal line the weld is not firm or bad connection etc The connector with 3 pins XLR is more universal than the one with 5 pins XLR 3 pins XLR PIN 1 GND PIN2 signal PIN3 signal 5 pins XLR PIN 1 GND PIN2 signal PIN3 signal PIN4 PINS UNUSED There can t be more than 16 PCS of lightings for series connection pattern when using 220V AC it can t exceed 8 PCS lightings for series connection pattern when using 110V AC POWER I DMX COMSOLE TO TERMINATOR DMX IN DMX OUT Dy OPERATION MENU Sending current settings to other fixtures when receive sucessfully will generate a reset Td _ DW address 01 512 Yes No o nw DPT 75 Dittmer node Dinner 1 4 L GE mode 100 130 Backlight Permanently on 2 Min
7. it will damage or interfere the DMX electric circuit Me beam Check whether the POW reduction is over temperature dim the brightness protection situation or not if yes please take measures for declines obviously ventilation Pan or Tilt rotating Check whether lead wire of motor or feedback position not work properly damage 9 DMX PROTOCOL Function Dim all Red Green Blue White No strobe Strobe slow fast Random Strobe slow gt fast Electronic Squarewave slow gt fast Virtual colour wheel No effect Blue Blue full Red Green White 0 step Red 0 Green gt up Blue full White 0 proportional Light Blue Red 0 Green full Blue full White 0 step Red 0 Green full Blue gt down White 0 proportional Green Red 0 Green full Blue 0 White 0 step Red gt up Green full Blue 0 White 0 proportional Yellow Red full Green full Blue 0 White 0 step Red full Green gt down Blue 0 White 0 proportional Red Red full Green 0 Blue 0 White 0 step Red full Green 0 Blue gt up White 0 proportional Magenta Red full Green 0 Blue full White 0 step Red gt down Green 0 Blue full White 0 proportional Blue Red 0 Green 0 Blue full White 0 step Sound control colour Pan Pan Fine Tilt Tilt Fine Speed Fast gt S low use menu setting dimmer Dimmer off Dimmer 1 Dimmer 2 Dimmer
8. mportant to do the maintenance work If the lighting is idle for a long time damp dust can cause greater accumulation of dirt on its cover or housing So it should be cleaned to maintain an optimum light output and at the same time to prevent it from corrupted by dust and acid gas Cleaning frequency depends on the lighting operation frequency and the environment in which the fixture operates Soft cloth and typical glass cleaning products should be used for cleaning It is recommended to clean lighting at least once every 20 days Do not use any organic solvent e g alcohol to clean housing of the apparatus 8 TROUBLESHOOTING PROBLEM REASON AND ACTION Check the power connection is correct or not The lighting can tbe Please detect the voltage started normally Power supply is damaged or incorrect connected Call a qualified personnel to fix it Connection of control board is not correct Call a qualified personnel to fix it Please check the DMX connector and the power connection is connected correctly or not It means having signal if it shows twinkling Out of console s of the decimal point which in the lower right corner of the screen control a when exiting the screen saver Please check the DMX address setting of lighting is correct or not Check CH mode setting is correct or not Please check whether the DMX line is near to the high voltage wire or not In that case
9. utes off sk ees 0 02 0o c oss gt E S 0 c oo c Oe LE 0 25 Sound Running _ Power reduction 100 80 50 _ Resume default Yes No Fixture reset Yes No Illustrations When the menu is set as the information of position the projector will be set automatically to be the main engine and then send data to external Other projectors can receive these data and run synchronously with the main engine It still be run according to these setting parameter even if power reconnection after power off When setting YES in Resume default menu The parameter will bereset to be the factory default value as which with underline of above chart 6 CONTRL PANEL DISPLAY SCREEN Display function menu and selection menu BUTTON OPERATION 1 MENU Return to previous menu 2 ENTER Enter to the next menu or save 3 UP Menu selection or increasing the parameter 4 DOWN Menu selection or decreasing the parameter SN S uL A j N M 2 x 7 OFF POWER IN DMX OUT DMX IN AC100 240V 50 60Hz POWER INPUT Supply power SINGNAL INPUT Connect forward lighting with XLR signal wire then input DMX512 signal SINGNAL OUTPUT Connect next lighting with 3 XLR signal wire then output DMX512 signal POWER SWITCH ON OFF PROTECTION Current excessive protection T MAINTENANCE To prolong the life of lighting it is very i
Download Pdf Manuals
Related Search