Leistungsermittlung Red Devil II Titanium
Contents
1. pk ek ph me v If the intake line is longer than 10 meters or the intake height is higher than 1 meter the diameter of the intake line must be 1 or 2 sizes bigger than the inlet of the pump gt 10m bl gt 1im Suction side 2 male threaded 110mm outer diameter dependant of model Suction line must be at least 875mm 1 4 Pressure side pump outlet The pressure side must be at least the same diameter like the diameter of the pump s outlet to avoid pressure drop too high flow rates and noise to a minimum At best increase the diameter of the tubing directly behind the pump to increase flow rate and save energy Avoid short 90 bends try to use long swept bends less pressure loss If there is a chance of a blocked pump e g closed ball valve a bypass must be installed to the pressure line to ensure some water flow through the pump K 2 ii u Connection pressure side 50 63mm or 2 male threading dependant of model Flow Maximum flow volume in pipe diameter Pipe diameter Optimal flow for mm minimum pressure loss I h 9 190 Electrical connections initial startup Compare voltage and frequency imprinted on the specification plate to the specifications of your mains voltage The one who is responsible for the installation must check if the voltage grounding was according to specifications It s also important to check if the installation was secured by a sens2. armature must be removed also to clean the housing 6 Contact service 7 Motor indicates an error Check the inlet and the housing for clogging 1 2 Repeat some start up s Fill pump and inlet tubes with water 3 Check tubes and valves for clogging Valves are closed 4 5 Check 6 Contact service 1 Refer to 2 2 Contact service 3 Bad ventilation when built into cabins or exposed to sunlight or high environment temperature Check inlet 4 Set speed to maximal power 1 Remove solids 2 Adjust voltage as required 3 Contact service Parts list 1 2 34567 8 g 10 11 12 13 1415 16 1 Titanium screws 5 Front bearing seat o snan ra Bearing Oving 2 Pumpnead 6 O ing bearing seat 10 Rear bearing seat 14 Rear bearing lock 4 siicone Oring a Siicium carbide bearing 12 motor nousing te Rearplate Codes The controller has a few buttons that are not activated to keep the usage simple These buttons can be activated through an optional code What do these codes offer After activating the codes the controller offers 5 different timers that can be independently programmed for e g different seasons With these timers both the time as well as the RPM can be adjusted Blue Eco pumps model 900 and up also activate a dry running protection that protects the bearings and a Cruise Control option This code can be purchased via e mail info_estrad me com In order to get these codes you need to wri
3. bearing which most likely will result in severe damage and thus in expensive repair costs After maintenance reassemble the pump in reverse order Do not over tighten the screws due to the fact that the threads in the case are made from plastic The O rings are made from silicone or EPDM Viton depending on the application As Spare parts only use new and original O rings with the proper thickness and hardness Used O rings slowly alter their hardness Always replace with new parts if disassembled to prolong the life time of the pump Silicone and EPDM Viton O Rings are resistant against acids and bases Bearings The bearings of the 240 and 320 are based on silicium carbide the hardest material after diamond The front and back bearing are equal and can be switched At normal use they will last for life Both bearings sit in a EPDM O ring that will adsorb vibrations and keep the bearing in a exact position The shaft of the Marine 240 320 is made of wolfram and also acts as a bearing The 500 900 1500 2200 Watt model have a flat silicium carbide slip bearing that will keep up with the axial and radial forces These bearings are exchangeable These bearings are based on a wet sealant that means that the pump has no seals that can leak The shafts of the 240 320 watt are made of an improved wolfram that is seawater resistant The shafts of the 500 900 1500 2200 Watt are made of 100 pure titanium of the highest class G5 Power outage auxiliar
4. the entire installation process Never put your hands or fingers into the openings of the powered pump to prevent injuries 1 1 Controller The controller unit can be installed indoor and outdoor Do not expose the controller to direct sun light or heat powerful lamp radiator Be sure there is enough air circulation Keep all sides of the unit free for at least 10cm gt 10 cm u lt gt _ gt e cm 1 2 Pump The pump must be installed in a horizontal position The pump must rest firmly on a flat and even surface Install the intake line to the pump s inlet 1 see fig Make sure the pump can evacuate air from the outlet 2 At best install the pump below the water level 3 The pump may be installed inside 4 as well as outside dry of the water 5 If operated outside check for sufficient air circulation Do not expose the pump to direct sunlight Install the pump as close as possible to the location of water withdrawal i e the intake line should be as short as possible If the pump was operated above the water level 6 install a check valve to the pump s inlet 7 In this case the intake line of the pump must be filled with water This kind of installation exposes the pump to dry run damages if the check valve doesn t work correctly Damages resulting from running dry are not covered by warranty 1 3 Suction side pump inlet If there is not enough water due to the resistance of the intake line
5. the pump needs a lot of power and the electronics will heat up in the long run The electronic circuit protects itself by powering down If the flow rate of the pump decreases within a couple of hours or days the reason might be the too high resistance of the intake line especially on warm days Try to enlarge the pipe diameter after the pump to a sufficient size for more pump capacity and and lower energy consumption It is not allowed to let the pump run dry It will lead to irreparable damage to the shaft and silicium carbide bearings Especially when the pump is mounted above the water surface level with a check valve you have to be very careful about this When used in dirty water the use of a previously described pre filter is necessary The use of flexible fittings or unions is recommended for easy dismantling for cleaning and or maintenance The pipe work must be fitted in a way that possible mechanical stress due to changing temperatures have no negative influence on the pump house Any tubing on the intake line must be 100 air tight If a hose was used as intake line make sure the hose is in accordance to the requirements for intake hoses It is very important that the intake line on the pump head is primarily straight min 5 times the diameter of the inlet This will increase the power of the pump due to the laminar water flow on the impeller Avoid short 90 bends try to use long swept bends less pressure loss 6x5
6. 320 500 900 1500 2200 watt depending on the model The pump will always run on the set power After a power break the pump will automatically return to the last setting INSTALLING If used in dirty water the pump requires a pre filter as mentioned earlier in the manual We recommend the use of 2 or 3 3 unions for easy disassembly for pump cleaning or maintenance Example 1 Suction side 2 part unions with rubber ring for easy sealing art nr AG287 21 x 63mm see picture Pressure side a PVC 3 part Union 63mm can be glued on the pressure side Do not glue straight socket fittings on the pump as this makes disassembly extremely complicated The use of pieces of flexible is recommended to prevent vibration and resonation see example 2 Model 240 320 Example 2 Flexible fittings provide a vibration free performance and are very easy to remove Suction side a solvent ring 90mm x 22 fem thr art nr AB367 can be fitted with some liquid Loctite 5331 art nr AK142 or Teflon tape On this ring a flexible reducer fitting 90mm 3 to 68mm 2 can be fitted art nr FC146 On the pressure side you can put a 63mm 2 flexible fitting straight socket FC122 or a 90 bend FC172 The rubber feet underneath the pump will provide a complete vibration free performance Model 240 320 Example Model 500 900 1500 2200 Suction side 2 part unions with rubber ring for easy sealing art nr AG28
7. 7 21 2 x 63mm see picture Option 2 a solvent ring 90mm x 2 fem thr art nr AB367 can be fitted with some liquid Loctite 5331 art nr AK142 or Teflon tape On this ring a flexible fitting 90mm to 110 90 63mm can be fitted art nr FC146 For the pressure side you can use a 3 3 PVC union O63mm x 2 fem thr art nr AB246 with teflon or Loctite 5331 art nr AK142 or a or a 2 3 union 2 x 68mm AG279 that seals with the rubber ring Model 500 900 1500 2200 Assembly Attention Read the manual carefully before installation of the pump Damages resulting from non observance are not covered by warranty When unpacking the pump check the parts for completeness and damages Damages detected must be advised to the supplier within 8 days after purchase It is possible that the pump is moist or wet after unpacking due to the fact that the pump had been tested before leaving the manufacturer Before wrapping the pump has been treated with a biodegradable disinfectant to eliminate possibly existing germicides Therefore the pump must be rinsed thoroughly before operation Check the pump for damage before putting into operation A damaged pump must NOT be operated Immediately contact your supplier Putting the pump into operation in spite of visible damages will void warranty and manufacturers liability Unplug the pump from the mains and make sure it cannot be operated The pump must not be connected to the mains during
8. Blue Eco Marine 240 320 500 900 1500 2200 User Manual BLUE ECO START UP INSTRUCTIONS ENG LISH Dear Blue Eco user Thank you for choosing Blue Eco pumps With these pumps you own the latest technology in variable pumps Blue Eco pumps are the most energy efficient pumps worldwide and are fitted with high tech features Your Blue Eco pump has a standard warranty period of 2 years after initial start up optional expandable to 4 years Fora decent warranty registration your pump has a maximum speed of 1200 RPM This maximum speed is set by the manufacturer as a good speed for running in the pump After registration on www blue eco nl you or your supplier will receive 2 codes that will release the full speed of the pump If you do not appreciate a personal registration you can register the pump on your supplier s name e mail address the purpose of this registration is to have the serial numbers of the pump and controller on the initial day of use During registration on www blue eco nl you will be asked for serial number 1 amp 2 of the controller You can retrieve these numbers in the display when you follow these instructions Turn on the controller and wait for O in the display Press the MENU button the display will show SYSTEM Press ENTER and press the yellow button with the A symbol 3 times SERIAL NUMBER 1 will appear in the display write down this number Press the A button again and write down S
9. ERIAL NUMBER 2 oe a You now have the 2 serial numbers for registration After registration and entering these serial numbers you will receive an e mail with codes and these instructions EXAMPLE You have successfully registered your pump and received 2 codes Your registration will be processed RPM activation code 1 xxxx RPM activation code 2 xxxx Your warranty period starts today NOTE THE PUMP MUST NOT RUN WHEN YOU ENTER THE CODES Follow these instructions to activate the codes 1 Turn on the controller and wait for O in the display 2 Press the MENU button once the display will show SYSTEM 3 Press ENTER the display will show TIMER MODE then press the yellow button with the A symbol 5 times 5 The display will show ACTIVE CODE with 4 digits for example 3998 6 Now enter the code that you have received by pressing the SELECT button the last digit will start blinking 7 With the Aand W buttons you can change this number Press SELECT again to go to the 3rd number and change with the Aand W buttons Repeat these steps for the 2nd and 1st numbers If you made a mistake press the SELECT button to go to the wrong number to change 8 Carefully check if all 4 numbers are now corresponding the received code then press ENTER 9 The display will show ALERT EEPROM CHANGE 10 Press RESET to store code 1 11 Now wait again wait for O in the display then repea
10. IATELY Only use cables adapters installations extension cords or power cables which are designed for outdoor use DIN VDE 0620 and with a proper cable diameter Do not pull or carry the device on the cables In the case of a defective cable or housing the device must not be used Protect cables and accessories against heat oil UV light and sharp objects The manufacturer cannot be held liable for damages resulting from unintended or inappropriate use or negligence of the user or installer Damages to the power plug or the housing remains the device unusable Repairs are impossible due to the fact that the cables were cast into the housing Keep the connectors dry In the case the connector got wet or humid it must be rinsed in demineralised water and must be carefully dried by a trained service person Generally the pump must be cleaned carefully before put out of operation At return of service check clearance of the impeller If the impeller cannot be moved the pump must be disassembled and cleaned DO NOT unplug the power plug while operating the pump and the controller This may result in severe damage of the internal electronics and dangerous hazards due to grounding problems The controller must be connected to a safety fault current detector 30mA and a properly installed wall plug Do not modify or replace any cables Electric installations on garden ponds must be in accordance with national and international regulations guidelines and
11. arising from injuries of life body and health to claims from Product Liability Code as well as claims from culpably breach of important contractual duties which compromise the purpose of the contract Incidentally our liability for gross negligent infringement of essential contractual obligations is limited to the typically incurring damages which were predictable when the contract was concluded Generally the customer takes full responsibility for damages arising from inappropriate operation of the goods When returning any goods the customer has to care about break proof packing The customer is liable to the full extend for damages arising from an inappropriate packing 1 6 Warranty claims against us are limited to 1 year after delivery of the goods to the purchaser The same applies for claims of compensation for whatever legal ground The restriction for the period of limitation does not apply for fraudulent concealment of a defect for claims based on the product liability code as well as damages arising from injuries to life body and health and for damages which result from intention or coarse negligence 1 7 If our investigations or repairs on a defect claimed by the customer turn out to be coarsely negligent we reserve to ask an adequate compensation for our investigations and or repairs The customer is entitled to refuse an essential repair and may request the return of the pump Basically we ask a costs compensation if the inspec
12. ce card By sending this service card in time you will be informed about updates through e mail and you will be served fast for repairs and other issues Telephone support is only possible if we have this card A pump that is send to us without having the service card in our system must be registered first which costs time We cannot guarantee 24 hours service if we do not have the service card 14
13. engineer standards Never open the housing of the device or attached parts if not explicit stated in the manual Use original spare parts and accessories only Repairs must be executed by trained service persons only DO NOT pump any liquids beside water In the case of questions or problems for your own safety contact trained service persons M Unplug the pump from main power before service and or maintenance Applications The BLUE ECO pump was designed for fresh brackish or salt water or other low viscosity liquids which are neither explosive nor aggressive or oily The pump may be used for clean water and in a limited way also for contaminated water The pump is not intended for water with coarse debris Particles should not be larger than 0 8 mm Basically the pump is intended for use with clean water without solid particles which may damage the bearings like for example sand and pyrolusite after the treatment of ponds with potassium permanganate Warranty does not apply for damages resulting from above described particles The bearings of the pump are milled spirally to evacuate particles larger than 0 8 mm The bearing plate contains enough space for a filter The filter must be cleaned regularly regardless the degree of soiling A special amount of water is flushing the pump housing to ensure long term operation of the pump To decrease the flow rate in the housing perfectly close the plate and adjust to the smallest dot on the pla
14. er installer or maintenance personal is solely responsible for the strict adherence of all instructions made in this manual The BLUE ECO was manufactured according state of the art technology and current safety regulations Nevertheless this device may involve risks for life and physical condition if not used as intended or if safety regulations were ignored If not used as intended our liability expires as well as the general operating license Children youth below an age of 16 as well as persons who may not recognize possible risks or who are not familiar with this manual must not use the device for safety reasons Please keep this manual safe and hand out in the case of change of proprietor The combination of water and electricity may severely harm life and physical condition if the device was not connected properly or used inappropriate Do not use the device as long as persons remain in the water Unplug all devices in the water before touching the water Check the specification of the mains against the electrical specifications NM on the package or the label of device Make sure the device is connected to a fault current detection switch with a fault leakage below 30 mA DIN VDE 01001739 Use the device only if plugged into a wall plug installed according to regulations Keep the power plug and all connections dry Install cables dry and save to avoid damage DO NOT CUT OR TRIM THE CABLE OR PLUG OF THE DEVICE CLAIMS AND WARRANTY EXPIRE IMMED
15. ic Compatibility EN 60335 1 2002 Household and similar electric devices EN 60335 2 41 2003 Household and similar electric devices typical requirements for pumps EN 60335 2 55 2003 Household and similar electric devices typical requirements for electrical devices like used in tanks and garden ponds EN 50366 2003 Household and similar electric devices Electromagnetic fields Procedures for evaluation and measurement EN 55014 1 2006 Electromagnetic compatibility Requirements for household devices electric tools and similar devices emissions EN 55014 2 1997 Electromagnetic compatibility Requirements for household devices electric tools and similar devices Immunity product group standard 3 1 Manufacturer Estrad BV Westeinde 46 7711 CL Nieuwleusen 3 2 Production All BLUE ECO PUMP series pumps and accessories are made in Netherlands and China Dear customer Thank you for choosing BLUE ECO pumps This pump has been developed under the newest technology available with the most modern and reliable parts Blue Eco pumps use True Sine Wave technology to provide the most energy efficient technique Please read this manual carefully before using the pump Symbols CAUTION HIGH VOLTAGE IGNORING THIS INSTRUCTION MAY HARM USER AND OR ANIMALS CAUTION l IGNORING THIS INSTRUCTION MAY DAMAGE THE PUMP AND OR OTHER DEVICES ATTACHED Not intended use This manual is intended to give you brief information about the device The us
16. itive fault current detection switch 30mA DIN VDE 01001739 The mains fuses should be stronger than the pump fuses Fuse 240Watt 320Watt Overload protection The Blue Eco pumps were equipped with electric and electronic fuses for overload protection If the impeller blocks the motor stops When blockage has been cleared the pump can be restarted again or it restarts itself where applicable 10 General operation Operation and function of the display Attention The imprint on buttons and display may differ from the text in the manual but the functions remain the same Keys amp Display LCD Display Run LED This led is on during pump performance Stop LED This led is on when the pump has stopped Increases the RPM Decreases the RPM The other buttons are not in use unless you activate a code see Code chapter in this manual The display shows the following data 1 Hour counter shows how many hours the pump has been running 2 Wattage the current energy consumption 3 RPM Rotations Per Minute 4 Amperage External connections The external connection with RJ45 connector can be used to change the RPM A 10volt signal triggers the maximum RPM 2800 Please note the 0 10volt signal cannot trigger a RPM setting lower than the current value Example the pump is running at 1500 RPM and the 0 10v connector sends out a low voltage that is below the 1500 RPM nothing will happen The moment the o
17. nance is restricted to impeller checking for clogging Remove potential objects from the impeller with a thin spiky tool A reduced delivery rate of the pump is generally caused by waste in the impeller In the case of calcification especially when used in salt water remove the scale with a weak acid like vinegar Avoid sidewise pressure to the impeller or the rotor The pump can be completely disassembled for cleaning The rear bearing can be easily removed by unscrewing of the bearing plate counter clockwise Use an appropriate tool to move the shaft to the front so the impeller unit can be removed much easier In fresh water applications calcification generally occurs before and after a complete pond filling The dissolved lime scale will precipitate within 2 or 3 days Use a M6 Allan key to remove the titanium screws 1 which mount the pump head to the motor housing Now the complete pump head can be removed If necessary remove the complete impeller from the 240 320 unit by pulling out the shaft after removing the O ring For the models 500 900 1500 2200 you need to remove the nut on the impellers front This will reveal 3 screws that also need to be removed You can now remove the shaft 12 Be very careful because the impeller is fixed to its position by a strong magnet Releasing the shaft occasionally may hit the bearing resulting in severe damage Do not underestimate the power of the magnets If you lose grip the shaft will hit the rear
18. nted performance arising from the fact that the customer moved the goods to a place other than his primary location will be charged Warranty is limited to the pump itself In no event will be liable to the purchaser or to any user of Estrad BV products for any damages expenses lost revenues lost savings lost profits or any other incidental or consequential damages arising from the purchase use or inability to use Estrad BV products even if Estrad BV has been advised of the possibility of such damages The customer is solely responsible for a standby unit in case of malfunction 1 3 The Customer shall be obliged to check the delivered goods also for product reliability immediately and notify the supplier in writing of any discrepancies Concealed damages have to be reported immediately after detection The customer has to report transport damages to the carrier within 24 hours after delivery No observance of due diligence will void the customers claim warranty 1 4 Furthermore we are not liable for consequences resulting from not intended operation handling and maintenance of the goods by the customer or his subsidiaries particularly for consequences resulting from thermal chemical electrochemical or electrical effects as well as infringements to the manual The same applies if the damage results from intervention or instructions by the customer which are not affirmed by us 1 5 Our liability for gross negligence is limited to claims
19. oduct apply Guaranteed characteristics made by third parties cannot be accepted The characteristics expressly stated in this manual apply If the goods are to be used for purposes other than intended the customer must carefully check usability and reliability on his own responsibility We are not liable for any usage other than expressly stated Manipulations of the pump the impeller the electronics as well as the trial to hack or read the firmware immediately voids warranty Please note that the controller software is protected Trying to read this software will activate its deletion Any customer is solely responsible for the intended usage of his BLUE ECO PUMP Using this manual does not absolve the user s responsibility for safe installation operation and maintenance By the use of this manual the customer accepts that the manufacturer cannot be held liable for material and personal damages arising from usage of the product In particular damages arising from improper tubing lack of maintenance calcinations as well as absorbed foreign substances like sand rocks which will damage impeller and bearings are not covered by warranty 1 2 Our liability for defects is strictly limited to supplementary performance At its own option Estrad BV shall mend or replace the defective goods In the case of rejection impossibility or failing of supplemented performance the customer may lower the price or negotiate the contract Higher costs for suppleme
20. same pump as model 2200 Noise emission The noise emission of the pump is within the limits of the machine guidelines of the European Council Short Instruction The pump is driven by a DC motor and therefore equipped with a controller Check the following sequence when starting the pump 1 Flush the pump thoroughly to remove any residual disinfection fluids 2 Install the pump below the water surface Pump is not self priming 3 Interconnect pump and controller using the attached controller cable check pins 4 Check the main power switch is set to O OFF 5 6 7 Connect the mains cable to the controller and plug into a wall plug Switch on the controllers power switch Press the RUN button pump will start after a 10 seconds delay Fuse Power switch Coded plug fits only one way Controller cable Power cable 230 V Switching the pump on and off oO INCREASE PUMP POWER when running Higher flow rate more energy consumption DECREASE PUMP POWER when running Lower flow rate less energy Apert After switching on there is a 10 second delay countdown After that the pump slowly increases speed to the previous value set while the flow rate is also updated When switched off the pump stops immediately A Y keys Use the A Y to set the power of the pump This will also change the flow l h and the energy consumption W and the RPM The power can be set between 10 and 240
21. t all above steps at Step 3 press the A button 6 times to reach Code 2 As soon as the display shows 0 again you can press RUN to start the pump You can use the Aand Wbuttons to change the RPM of the pump If you need any assistance you can call the Estrad service desk at 31 529481543 Estrad BV is not responsible for damage caused by the pump user Thank you for choosing Blue Eco pumps The Blue eco Team If you registered your pump on the website it is not necessary to send in the supplied warranty papers Keep them safe for future use About this manual Please read the manual carefully before installation and operation of the pump to avoid questions and problems Operating the pump is considered as acknowledgement that you have read the manual In the case you didn t catch on the manual please contact your dealer Warranty claims amp claims based on defects 1 Warranty claims 1 1 We are liable that our goods are free of faults until passing of risk Negligible deviations from conditions stated or marginal impairment of serviceability are to be disregarded The state contractually owed durability and usage of the goods delivered comply with the written specifications product descriptions and or manuals Any further statements in particular preliminary talk advertisement and or referenced industrial standards shall be only integral part of the contract when written Our expressly stated characteristics of the pr
22. te Now the bearing lubrication by water is very low The BLUE ECO Pump is generally used for filter systems of ponds or pools and or for brooks and cascades The pump is not self priming so for use above the water surface a check valve must be installed to the pump s inlet In this case the pump must be water filled before operation SS me P u A Ke pres of r p gt gt alge fs a r af aut x pEi er a m po P ER a P Na Pre filter example Intended use Liquid temperature 0 to 40 C Environmental temperature from 0 C to max 50 C Maximum operation pressure 2 bar 20 meters water column Features 1500 Voltage 110 220 Volt 50 60 Hz Induced power Nominal power Efficiency External controller IP68 Cable Digital display finlt 40 50mm 2 male thr 2 male thr 2 male thr 2 male thr 2 male thr 2 male thr sf rem Geo ao0 sanso 200 s3200 300 2050 300 1300 300 2200 200 23400_ For more specification refer to the type plate Model identification The Blue Eco 240 and 320 Watt use the same model pump the controllers are different This means that a model 240 can be controlled by a 320 watt controller and vice versa Model 500 uses the same pump as model 900 The controller determines the model In the future you can decide to buy a 320 controller for a model 240 or a 900 controller for a 500 Model 1500 uses the
23. te down 2 serial numbers from the controller display How to obtain these serial numbers Turn on the controller without the pump cable After the start up the display shows O RPM Press the MENU button Display shows SYSTEM Press ENTER to activate Press arrow up button twice the first serial number will appear write this down Press arrow up button twice again the second serial number will appear write this down Send these 2 numbers via e mail to info_estrad me com NOOR WD You will receive an invoice After the payment has been received you will get an e mail with the activation codes and a manual how to use them You also have access to the telephone helpdesk of Estrad for advice Extended warranty When you send your service warranty papers to info_estrad me com you can choose to extend your warranty from 2 to 4 years You will receive an invoice Once paid the extended warranty is valid This extended warranty is only possible within 30 days after the pump purchase Extended warranty after this period is possible after a pump controller inspection through Estrad and will be charged separately Service Warranty card You need to check if your dealer completes the service card at the time of purchase and sends it out to Estrad We can only guarantee a swift service if we have your service card Warranty extension and upgrade codes cannot be supplied if we don t have your servi
24. tion of a defect turned out to be caused by the customer 2 Spare parts Our obligation for stocking delivery of spare parts is limited to a period of 5 years after delivery The prices of our price list apply for spare parts 3 Disposal We offer free disposal and recycling of all our products covered by the Electrical and Electronic Equipment Act which have been delivered after 2005 August 13th within Germany If the customer decides to arrange the disposal himself he accepts the duties according the legal requirements on his own expense and indemnifies us from the take back obligation stated in 10 section 2 of the Electrical and Electronic Equipment Act and coherent claims of third parties 4 The manufacturer is entitled to initiate hard and software modifications of the product without notification as long as operation reliability and quality of the pumps were improved No claims can be made when e g design functionality or power of the pumps were changed fundamentally It is assured that the guaranteed specifications remain unmodified CE Manufacturer s declaration The manufacturer ensures and declares that the products of the BLUE ECO PUMP series are in accordance to the following EWG regulations when installed and used according the manual Machine 98 37 EG Electromagnetic Compatibility 89 336 EEC 73 23 EWG 95 EN ISO 12100 Norm EN 61000 6 2 Electromagnetic Compatibility EN 61000 6 3 Electromagnet
25. utgoing signal is higher than the 1500RPM the 1500 RPM will increase Use pin 2 and 5 of the RJ45 connector Signal port 1 Source current of 5 Volt 2 DC control current 0 10 volt 0 10V connection 3 Program inlet TXD 4 Program in Program inlet let RXD 5 GND 6 NC 7 NC 8 NC 11 Error messages When there are errors or changes occur the output to the pump will be stopped and the display will give an ALERT message The 3 line in the display will indicate the error code This is a list Wanneer er fouten ontstaan of veranderingen plaatsvinden zal de output naar de pomp gestopt worden en komt er ALERT in het display te staan De derde regel geeft de foutcode weer hieronder volgt een index met fout codes The current transducer on V phase is wrong The input power is wrong The temperature of controller gets too high The current of input gets too big The pump is blocked and controller can t start it The output cable connection is wrong The software is unauthorized Controller diagram 3 phase inverter bridge abeyoN Od sua ung JOO a a q o Meus WMd 4 Uam Signal Input output D CONTROL CIRCUIT Diagram of Pump Controller Maintenance Unplug the pump before maintenance Blue Eco series are basically treated as low maintenance In normal case mainte
26. y power supply After a power out the pump automatically restarts itself and the controller resets to the speed previously set The pump can be with a common auxiliary power supply when equipped with a rectifier The pump can be used with a common UPS when equipped with a rectifier Troubleshooting 1 The Pump delivers no water The Motor is not running The display is not lit 2 The Pump delivers no water The motor is not running 3 The volume of water delivered is limited 4 Erratic fluctuations t f E F ii 1 The Pump delivers no water The Motor is not running The display is not lit 1 Low mains voltage 2 Connector not properly seated 3 No proper connection from pump to controller 4 Fault current protection switch triggered 5 Impeller clogged 6 Pump electronics or motor defective 7 Motor fuse switched off motor 1 Pump takes air in 2 Air bubble in impeller housing 3 Too much head pressure in the system 4 Pump not filled with water 5 Inlet tube or check valve clogged 6 Delivery height exceeded 1 Refer also to 2 2 Impeller worn or damaged 3 Electronics over heated 4 Low speed 1 Impeller rotation blocked 2 Voltage out of range 3 Motor damage MALFUNCTION POSSIBLE CAUSE SOLUTION 1 2 3 Check mains and power plug 4 Reset fault current protection switch If it s triggered again check the impeller for blocking 5 Check Impeller for blocking Probably the
Download Pdf Manuals
Related Search