IEPS5 User Manual
Contents
1. DC chargers are able to deliver up to 2 5 times the rated current when mains power is on Connection polarity It is critical to check the polarity carefully when connecting DC devices Some Innovative Energies models have re verse polarity protection RPP for example the Smartchargers have electronic non destructive RPP the No Break DC range has an internal fuse which needs to be replaced if the battery is connected in reverse Usually however a reverse polarity connection results in instant destruction of the device especially if there is a battery involved Glossary of terms used in our user manuals PSU power supply unit BCT battery condition test ECB electronic circuit breaker ELVD electronic low voltage disconnect RPP reverse polarity protection EMI electromagnetic interference SNMP Simple Network Management LAN local area network DOD depth of discharge Protocol Specifications are subject to change without notice No liability accepted for errors or omissions 2 ovative energies Global Solutions Personal Focus 100W Standalone PSU with battery backup e Universal input 90 264VAC 127 370VDC e High efficiency switch mode design e Internal battery allows for high peak current draw and back up on mains fail e Internal diode in positive leg to prevent discharge of battery while not in use e 12V 7Ah battery included e Easily removable lid for battery replacement e Single easy to use packag2. of 3 5mA Ventilation High operating temperature is a major cause of power supply failures for example it has been well documented that a 10 C rise in the operating temperature of a component will halve its expected life Therefore always ensure that there is adequate ventilation for the equipment Batteries and cooling fans also suffer shortened lifetimes if subjected to high ambient temperatures both should be included in a routine maintenance schedule to check for signs of reduced effi ciency Water Dust Every effort must be made in the installation to minimise the risk of ingress of water or dust Water will almost always cause instant failure The effects of dust are slower in causing failure of electronic equipment but all electrical equip ment should be cleaned free of any dust accumulation at regular intervals Electromagnetic Interference EMI Switching power supplies and converters inherently generate electrical noise All wiring should be as short as practica ble and segregated from all equipment wiring which is sensitive to EMI Residual noise can be reduced by looping DC wiring through ferrite cable sleeves These are most effective as close to the power supply as possible and as many turns of the wire taken through the core and in the same direction as the core will accommodate Fuse ratings Check that the wiring and fuses or MCBs match the rating of the PSU or converter Note that the Innovative Energies No Break
3. Phone 64 9 835 0700 Fax 64 9 837 3446 NZ Freephone 0800 654 668 energies AU Freephone 1800 148 494 www innovative co nz Global Solutions Personal Focus Email info innovative co nz User Manual IEPS5 100W Standalone PSU with battery backup T 7 Te Li ia ISO9001 Certified Specifications are subject to change without notice No liability accepted for errors or omissions energies Global Solutions Personal Focus Safety The user is responsible for ensuring that input and output wiring segregation complies with local standards and that in the use of the equipment access is confined to operators and service personnel A low resistance earth connection is essential to ensure safety and additionally satisfactory EMI suppression see below HAZARDOUS VOLTAGES EXIST WITHIN A POWER SUPPLY ENCLOSURE AND ANY REPAIRS MUST BE CARRIED OUT BY A QUALIFIED SERVICEPERSON Electrical Strength Tests Components within the power supply responsible for providing the safety barrier between input and output are con structed to provide electrical isolation as required by the relevant standard However EMI filtering components could be damaged as result of excessively long high voltage tests between input output and ground Please contact our techni cians for advice regarding electric strength tests Earth Leakage The EMI suppression circuits causes earth leakage currents which may be to the maximum allowable
4. cifications are subject to change without notice No liability accepted for errors or omissions 3 LY TERMS OF WARRANTY Innovative Energies Ltd warrants its power supplies for 24 months two years from date of shipment against material and workmanship defects Innovative Energies liability under this warranty is lim ited to the replacement or repair of the defective product as long as the product has not been damaged through misapplication negligence or unauthorized modification or repair Innovative Energies Limited Phone 64 9 835 0700 Freephone 0800 654 668 New Zealand 1800 148 494 Australia Fax 64 9 837 3446 Email info innovative co nz Online www innovative co nz In Person 1 Heremai Street Henderson Auckland New Zealand By Post PO Box 19 501 Auckland 1746 New Zealand energies Thank you for purchasing from Innovative Energies We trust your power supply will exceed your expectations and perform for years to follow Sincerely The Innovative Energies team so 900 23 12 11 4
5. e e 1509001 Design management system 24 Month Warranty SPECIFICATIONS All specifications are typical at nominal input full load and at 20 C unless otherwise stated PHYSICAL Input voltage 85 265V 50 60Hz AC Input connector IEC320 socket Fusing Protection AC input fuse 3A DC Connections Banana plug screw terminal posts DC battery output MCB 10A PSU constant current limit Enclosure Steel powder coated lid Overvoltage protection Mounting Desktop Control ON OFF switch on front panel Isolation 1KV DC input output earth Dimensions 178 x 300 x 78 mm W x D x H Bower 100W including rubber stand off feet Weight with batt Output voltage 13 8V mains on Eden attery 5 Kg Current 6 5A continuous mains on 16A peak mains on Indicators Mains on DC output present STANDARDS EMI EN55022 2006 Class B Battery 7Ah sealed lead acid Estimated back up time at 6 5A 12 to 15 Safety EC950 EN60950 AS NZS3260 UL1950 minutes with battery in good condition External batteries properly fused may be connected for extra backup time or higher peak currents ACCESSORIES SUPPLIED AC power cord 1 5m with IEC320 socket and NZ Aust plug MCB must be closed for battery to be connected MCB should be tripped when in storage or if not connected to mains power Briefly connect DC output terminals together to open MCB DC Output Terminals AC Input Socket Switch and Fuse Spe
Download Pdf Manuals
Related Search