Prizmatix UHP-T-LED User Manual
Contents
1. ONLY if all two cables from LED head to controller are connected Note The LED head contains a thermistor to regulate the temperature of the LED and the fan is activated only once the LED begins to warm up When the LED is switched on from a cold state at the maximum power setting the fan will start to work after 5 20 seconds depending on the wavelength Figure 5 Cable connections on the rear panel of the UHP LED Current Controller Main Office Phone 972 72 2500097 Fax 972 72 2500096 Fax sales europe prizmatix com sales prizmatix com European Sales Office Phone 44 0 77 9172 9592 North America Sales Office Phone 1 248 436 8085 44 0 20 7681 2977 Fax 1 248 281 5236 Ssales uSa prizmatix com P O B 244 Givat Shmuel 54101 Israel Prizmatix UHP T LED Microscope Alignment Z alignment of the Collimator lens is required to optimize the illumination provided by the UHP T LED Adjustment of the Z placement of the collimating lens relative to the LED chip is done by slightly turning the Z Adjust screw on the faces of the UHP T LED head see Figure 6 below Note that the span of the screw motion is less than one full turn this covers the full Z adjustment parameters FocusAdjust Figure 6 Z Axis Focus Adjust Disconnection of UHP T LED from a microscope 1 Turn the power OFF and disconnect the cables from the LED head 2 Loosen the two fixation set screws or the F2. ED head with Olympus Zeiss Nikon Leica microscope adaptor optional UHP T LED Controller Ultra High Power LED Benchtop Current Controller Switch Keys Switch keys for ON OFF power switch LED Control Cable Cable to connect the UHP T LED to Controller LED Current Cable Cable to connect the UHP T LED to Controller Ll Mains Power Cord Cord to connect the power adaptor to mains voltage 1 Power Adaptor Universal power adaptor Main Office European Sales Office North America Sales Office Phone 972 72 2500097 Phone 44 0 77 9172 9592 Phone 1 248 436 8085 Fax 972 72 2500096 Fax 44 0 20 7681 2977 Fax 1 248 281 5236 sales prizmatix com sales europe prizmatix com Ssales uSa prizmatix com P O B 244 Givat Shmuel 54101 Israel Prizmatix System overview System LED Emission Power Switch System LED Output ON OFF Power Control Figure 1 Front panel of UHP T LED Current Controller TIL Input Connector Connector for LED Control Cable TTL Enable Switch Connector for LED Ain Enable Current Cable Switch Analog Input 6 Np DC Power Jack Connector Figure 2 Rear panel of UHP T LED Current Controller Main Office European Sales Office North America Sales Office Phone 972 72 2500097 Phone 44 0 77 9172 9592 Phone 1 248 436 8085 Fax 972 72 2500096 Fax 44 0 20 7681 2977 Fax 1 248 281 5236 sales prizmatix com sales europe prizmatix com sales usa prizmatix com P O B 244 Givat Shm
3. Prizmatix UHP T LED User Manual Ver 03 July 2014 Main Office European Sales Office North America Sales Office Phone 972 72 2500097 Phone 44 0 77 9172 9592 Phone 1 248 436 8085 Fax 972 72 2500096 Fax 44 0 20 7681 2977 Fax 1 248 281 5236 sales prizmatix com sales europe prizmatix com Ssales uSa prizmatix com P O B 244 Givat Shmuel 54101 Israel Prizmatix UHP T LED System Description The UHP T LED is an Ultra High Power LED light source for fluorescence microscopy Optogenetics High power illumination and other applications It is an effective replacement of spectral lamps and lasers The LED driver supports CW or external TTL modulation with user controlled frequency and duty cycle Safety Before applying power to the power adaptor of the system ensure that the protective conductor of the three conductor mains power cord is correctly connected to the protective earth contact of the socket outlet Improper grounding can cause electric shock and damage to health or even death When wiring the device first disconnect it from the power source and then turn OFF the main switch on the front panel Failure to do so may result in electric shock injury and or damage of your equipment Prizmatix products are NOT authorized for use as components in life support devices or systems The Current Controller and UHP T LED heads must not be operated in explosion endangered environments Any maintenance shall be perfo
4. he general cabling system is shown in the diagram below 110 240V Power Adaptor UHP T LED Head UHPTLCC UHP T LED Current Controller 2 Put the Key in the Power Switch of the UHP T LED Current Controller and ensure it s turned to the OFF position 3 Turn the LED power adjustment dial on the front panel of the Current Controller counterclockwise to the lowest setting Main Office European Sales Office North America Sales Office Phone 972 72 2500097 Phone 44 0 77 9172 9592 Phone 1 248 436 8085 Fax 972 72 2500096 Fax 44 0 20 7681 2977 Fax 1 248 281 5236 sales prizmatix com sales europe prizmatix com Ssales uSa prizmatix com P O B 244 Givat Shmuel 54101 Israel Prizmatix 4 Connect the LED Control Cable and the LED Current Cable to the UHP T LED Current Controller and to the UHP T LED Head See Figure 5 below 5 Connect the Power Adaptor cord to the 12VDC jack on the back panel of the Current Controller So oo m ON Connect the Mains Power Cord to the Power Adaptor Plug the Power Adaptor into the wall outlet with the Mains Power Cord Switch the Int Ext toggle switchs at the back panel of Current Controller to Int position Turn the Key Switch to ON position The small red indicator on the front panel will light 10 Switch to ON the LED Emission Switch and adjust the dial control to the desired output power level Note The small red indicator on the front panel will light ON
5. mount collar on Nikon 3 Pull out the UHP T LED head to disengage it from the microscope Main Office European Sales Office North America Sales Office Phone 972 72 2500097 Phone 44 0 77 9172 9592 Phone 1 248 436 8085 Fax 972 72 2500096 Fax 44 0 20 7681 2977 Fax 1 248 281 5236 sales prizmatix com sales europe prizmatix com Ssales uSa prizmatix com P O B 244 Givat Shmuel 54101 Israel Prizmatix LED Control by TTL and or Analog Input The TTL input TTL and Analog Input Ain BNC connectors are placed at rear panel of the Controller featuring the TTL and Ain connector and toggle switches as shown below in Figure 8 To control the LED by TTL input e Connect the BNC cable to the TTL input and to voltage source e Place the Ain Enable Switch to Ext position e If TTLsignal is not in use place the TTL Enable Switch to Int position To control the LED power via Analog Input voltage e Connect the BNC 50o0hm cable to the Ain input and to voltage source e Place the Ain Enable Switch to Ext position e If TTLsignal is not in use place the TTL Enable Switch to Int position TTL Input Connector Connector for LED Control Cable TTL Enable Switch Connector for LED Ain Enable Current Cable Switch Analog t nalog Inpu DC Power Jack Connector Figure 8 Rear panel of UHP T LED Current Controller with Analog Input option installed Remarks The absolute maximum voltage applied to Ain is 5V The inte
6. rmed ONLY by a Prizmatix authorized technician The head of the UHP T LED can emit UV and other intense light When using a UV LED intense ultraviolet light can be emitted by the system during operation Precautions must be taken to prevent looking directly at the UV light with unprotected eyes or the shining of UV light onto bare skin Do not look directly into the UV light or through the optical system during operation of the device this can be harmful to the eyes even for short periods due to the high intensity of the UV light If it is necessary to view the LED s beam use protective glasses to avoid damage by the intense light In some cases following may apply UV LED N DANGER LED RADIATION AVOID EXPOSURE TO BEAM CLASS 3B LED PRODUCT Main Office European Sales Office North America Sales Office Phone 972 72 2500097 Phone 44 0 77 9172 9592 Phone 1 248 436 8085 Fax 972 72 2500096 Fax 44 0 20 7681 2977 Fax 1 248 281 5236 sales prizmatix com sales europe prizmatix com Sales uSa prizmatix com P O B 244 Givat Shmuel 54101 Israel Prizmatix Unpacking and Set up of the Device Remove the device from packaging and inspect it for loose components or any signs of damage Notify Prizmatix if the device appears damaged in any way do not install a damaged device Contents List UHP T LED XXX Head UHP T Controller with Keys Mains Power Cord Power Adaptor Item Description 1 UHP T LED XXX Head UHP T L
7. rnal pin of BNC connector is Positive The external part of the connector is Negative The Ain input is not opto isolated The Ain intended for control of LED power via Digital to Analog D A modules It is not suited for analog modulation of LED power at rates higher than few 10Hz Attention Any overriding of the maximum voltage or inverse polarity may cause permanent damage to LED and Current Controller Main Office European Sales Office North America Sales Office Phone 972 72 2500097 Phone 44 0 77 9172 9592 Phone 1 248 436 8085 Fax 972 72 2500096 Fax 44 0 20 7681 2977 Fax 1 248 281 5236 sales prizmatix com sales europe prizmatix com Ssales uSa prizmatix com P O B 244 Givat Shmuel 54101 Israel
8. uel 54101 Israel Prizmatix Connector for LED Control Connector for LED Control Figure 3 UHP T LED Head Tools required for installation Microscope Hex key Lamp port set screws 2mm Hex key or 5 64 Hex Key UHP T LED Z Axis Focus adjustment Setting up the UHP T LED on a microscope 1 The UHP T LED is designed to fit into the fluorescence lamp port of a microscope 2 Dismantle any existing fluorescence lamp Hg Xenon etc from the microscope most microscopes manufacturers Zeiss Olympus Leica use set screws to tighten the lamp onto the port of the microscope body Release the screws and carefully pull out the lamp In the case of Nikon microscopes with an F mount port turn the grooved collar counterclockwise and release the lamp 3 Carefully insert the UHP T LED into the lamp port Ensure the Z adjustment screw is accessible and tighten the set screws or collar in Nikon microscopes Main Office European Sales Office North America Sales Office Phone 972 72 2500097 Phone 44 0 77 9172 9592 Phone 1 248 436 8085 Fax 972 72 2500096 Fax 44 0 20 7681 2977 Fax 1 248 281 5236 sales prizmatix com sales europe prizmatix com Ssales uSa prizmatix com P O B 244 Givat Shmuel 54101 Israel Prizmatix Olympus Lamp Allen Hex J Fixation Set Screw Driver 4 Screw Lamp Fixation Set Screw Figure 4 The lamp port and its set screws Olympus microscope shown UHP T LED System Connection 1 T
Download Pdf Manuals
Related Search