User`s Manual
Contents
1. System Management Bus Connector SMBUS This pin header allows you to connect SMBus System Management Bus devices Devices communicate with a SMBus host and or other SMBus devices using the SMBus interface Pin Signal 1 SMBCK BOC 2 SMBDT 1 3 GND Serial Port Connector COM2 3 4 COM pin headers can be used to attach an additional port for serial devices Pin Signal Pin Signal 1 COM_DCD 2 COM SIN 3 COM SOUT 4 COM DTR 5 GND 6 COM DSR 7 COM RTS 8 COM CTS 9 COM RI 10 KEY VB7007 User Manual Case Connector F PANEL The F PANEL pin header allows you to connect the power switch reset switch power LED sleep LED HDD LED and the case speaker Pin Signal Pin Signal 1 5VDUAL 2 5V 3 5VDUAL 4 HD_LED 5 PLED_2 6 PW_BN 7 5V 8 GND 9 NC 10 RST SW 11 NC 12 GND 13 SPEAK 14 5V 15 KEY 16 SLEEP_LED Power LED PLED The LED will light when the system is on If the system is in S1 POS Power On Suspend or S3 STR Suspend To RAM state the LED will blink HDD LED HD_LED HDD LED shows the activity of a hard disk drive Avoid turning the power off when the HDD LED is still on Connect the HDD LED from the system case to this pin Power Switch PW_BN Connect to a 2 pin power button switch Pressing this button will turn the system power on or off Speaker SPEAK This pin header is for connecting to the system buzzer2. Settings Disable 1 Min 2 Min 3 Min 4 Min 5 Min 6 Min 7 Min 8 Min 9 Min 10 Min 11 Min 12 Min 13 Min 14 Min 15 Min VB7007 User Manual Power Management Timer Settings Disable 1 Min 2 Min 4 Min 6 Min 8 Min 10 Min 20 Min 30 Min 40 Min 1 Hour Video Off Option Select whether or not to turn off the screen when system enters power saving mode ACPI OS such as Windows XP will override this option Settings Description Always On Screen is always on even when system enters power saving mode Suspend gt Off Screen is turned off when system enters power saving mode Power Off by PWRBTN Settings Description Delay 4 Sec System is turned off if power button is pressed for more than four seconds Instant Off Power button functions as a normal power on off button Run VGABIOS if S3 Resume Select whether to run VGA BIOS if resuming from S3 state This is only necessary for older VGA drivers Settings Auto Yes No AC Loss Auto Restart The field defines how the system will respond after an AC power loss during system operation Settings Description Off Keeps the system in an off state until the power button is pressed On Restarts the system when the power is back Former Sts Former Sts VB7007 User Manual Hot Key Any Key Any Button Disabled Disabled Enabled By 0S1 Disabled PS2KB Wakeup Select This feature has two setting
3. Reset Switch RST_SW The reset switch is used to reboot the system rather than turning the power ON OFF Avoid rebooting the system if the HDD is still working Connect the reset switch from the system case to this pin Sleep LED SLEEP_LED The SLEEP LED is lit when the system is in the S1 POW Power On Suspend VB7007 User Manual KB MS g EE E ae I om m 099898 il 000 S PN Front Panel KBMS Connector KB MS The mainboard provides a PS2 pin header to attach a PS2 keyboard and mouse Pin Signal Pin Signal 1 5VDUAL 2 GND 3 KB_CLK 4 KB_DATA 5 EKBCLK 6 EKBDATA 7 MS_CLK 8 MS_DATA 9 EMSCLK 10 EMSDATA VB7007 User Manual Fast Infrared Connector FIR in Signal 1 5V IRRX1 00000 IRRX GND U RKWINIk lg IRTX FIR lo Front Audio sppIF S PDIF Connector SPDIF Signal 5V SPDIF_OUT 1 UT Wl
4. Enabled AGP Aperture Size This setting controls how much memory space can be allocated to AGP for video purposes The aperture is a portion of the PCI memory address range dedicated to graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation Settings 32MB 64MB 128MB 256MB 512MB 1GB AGP3 0 Mode This mainboard supports the AGP 8x interface When the AGP 8x video card is used it can transfer video data at 2133MB s AGP 8x is backward compatible leave the default 4x mode on AGP 4x mode can be detected automatically once you plug in the AGP 4x card Settings 8x 4x AGP Fast Write Settings Disabled Enabled VB7007 User Manual AGP 3 0 Calibration Cycle Settings Disabled Enabled VGA Share Memory Size This setting allows you to select the amount of system memory that is allocated to the integrated graphics processor Settings Disabled 16M 32M 64M Direct Frame Buffer Settings Disabled Enabled Outport Port Settings DIO DI1 Dithering Settings Disabled Enabled VB7007 User Manual By Auto Enabled Optimize VLink Mode Selection Settings By Auto Mode 0 Mode 1 VLink 8X Support Settings Disabled Enabled DRDY Timing Settings Slowest Default Optimize VB7007 User Manual Press Enter Enabled Enabled Enabled Disabled Press Enter Enabled CIDE Auto Enabled
5. Settings Enabled Disabled VB7007 User Manual WatchDog Support Settings Enabled Disabled Watch Dog Timer Select This option can only be altered if WatchDog Support is enabled Settings Minute Second Watch Dog Count Value This option can only be altered if WatchDog Support is enabled Settings any integer from 0 to 255 VB7007 User Manual 3F8 IRQ4 2F8 IRQ41 3E8 IRQ41 2E8 1RQ41 3787 IRQ7 1 SPP EPP1 71 31 Disabled Onboard Serial Port 1 2 3 4 Set the base I O port address and IRQ for the onboard serial port A serial port B Selecting Auto allows BIOS to automatically determine the correct base I O port address Settings Port Settings 1 Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Auto 2 Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Auto 3 Disabled 3F8 IRQ5 2F8 IRQ10 3E8 IRQ5 2E8 IRQ10 4 Disabled 3F8 IRQ5 2F8 IRQ10 3E8 IRQ5 2E8 IRQ10 Onboard Parallel Port This specifies the I O port address and IRQ of the onboard parallel port Settings Disabled 378 IRQ7 278 IRQ5 3BC IRQ7 a VB7007 User Manual Parallel Port Mode Set the parallel port mode To operate the onboard parallel port as Standard Parallel Port choose SPP To operate the onboard parallel port in the EPP mode choose EPP By choosing ECP the onboard parallel port will operate in ECP mode Choosing ECP EPP will allow the onboard parallel port to support both the E
6. eseserssereesserevsseersssseressservssseerrssseressserersssrerssseeesseee Memory Slot DDR2 DIMM issosssevossseressseressseresssseensse DDR2 SDRAM Module Installation Procedures Available DDR2 SDRAM Configurations Connecting the Power Supply smsrrsssrnsssrsssrssssrsssvrnns ATX 20 Pin Power Connector n sssesssesssesssesssenssensee Back Panel Ports PS 2 ports mouse and keyboard ssseesserresssernsss VGA port Serial port COM issesseee Parallel port USB Ports TPA Fk gt re nen noe R Audio jac Connectors Serial ATA Connectors SATA1 and SATA2 IDE Connector IDEL insrsseessrsserssrssrssrrssrssrsssrserssesssrserne USB Pin Connector USB 0 1 and USB_2 3 Digital I O Connector DIO ss esseressseressseressseresssseeesse System Management Bus Connector SMBUS Serial Por Case Connector F PANEL uses KBMS Connector KB MS rervvorervrvrevrsevevssveveevevsvssses Fast Infrared Connector FIR ks Line in Line out and MIC in t Connector COM2 3 4 sesse S PDIF Conn et r SPDIP yserenenrinassnnsaminnoninan nnii 21 Front Audio F AUDIO errerserrevsesvessvsvrsersersevsevsersvsvesersersersersevsessessvssesersersersersere 22 LVDS Connector PANEL CONN nmnnsesrrserrrvererserersevsrserersersrserersersssersssersssersesene 23 LVDS Inverter INVERTER insrssrnsrrsrnsersrsersernerversensersensersrssesers
7. usserseesservssseerssseerrssseersssseesssseressseresssererssseeessssresee 57 PS2KB Wakeup Select sseussrevsseressseressssresssseressserersssernssseressseresssererssesenssvernnse 57 PS2KB Wakeup Key Select nnvsuserssevsevsseessseersssseressserersserersssereess 57 PS2MS Wakeup Key Select n nssrusrssesserssseressseressseressseverssseeessseeeens 57 PS2 Keyboard Power ON nn ssserersseressseersssseesssseressssresssssenssseressseressserersseseessssreene 57 PS2 Mouse Power ON nn srarserassseeesssrersvssersvssevessssressssvessssersvsseressssvesssseessssseenes 58 USB Resume sssessrassraserassrassrassesssessserssesssesssessseesseenseenseesseesseesseenseesseesseenseenssenseenee 58 PowerOn by PCI Card ss sesessseressseresssesessseeessssevessssresssssenssseeessseressssrerssssersssseneee 58 RTC Alarm SE 58 Date Of Month nmseenveeseerseoveesverserverrsrsservsvrsenverssrrserverssersersersserserssersersensseenser 58 Resume Time Nhimm ss sissisotaan 58 PnP PCI ConfigurationS srussrvsrersserrssseerssseeerssseresssererssseressseresssererssssesssssenese 59 PNP OS Installed esse scsescassczeccsscatessiscedasust he scoscebiccascedsccdscndbslodelgcnaecitanbscteiecstole 59 Reset Configuration Data iss esseeessrvsseeressseerssseerssseersssseressseressserersssrersssseeese 60 Resources Controlled BY issessserevsservsssrrnssserrsssererssseressseressseresssererssesensserenese 60 ASSIgh IRQ for VGA ioe cccsccscssts
8. Discard all BIOS setting changes and exit setup VB7007 User Manual Jul 1 2008 er None None Change the None and cen None Al But Keyboard Date The date format is Day Month Date Year Time The time format is Hour Minute Second Halt On Set the system s response to specific boot errors Below is a table that details the possible settings Settings Description All Errors System halts when any error is detected No Errors System does not halt for any error All But Keyboard System halts for all non key errors VB7007 User Manual Press Enter Auto Auto Auto Auto The specifications of your drive must match with the drive table The hard disk will not work properly if you enter incorrect information in this category Select Auto whenever possible If you select Manual make sure the information is from your hard disk vendor or system manufacturer Below is a table that details required hard drive information when using the Manual mode Settings Description IDE Channel The name of this match the name of the menu Settings None Auto Manual Access Mode Settings CHS LBA Large Auto Capacity Formatted size of the storage device Cylinder Number of cylinders Head Number of heads Precomp Write precompensation Landing Zone Cylinder location of the landing zone Sector Number of sectors Prim
9. VB7007 User Manual Serial ATA Connectors SATA1 and SATA2 The current SATA interface allows up to 300 MB s data transfer rate faster than the standard parallel ATA with 133 MB s Ultra DMA go J HHHH i m m 000 ag o i E a sen i q H 88 o In il 2 SATA VB7007 User Manual IDE Connector IDE1 The mainboard has an Ultra DMA 133 100 66 33 controller You can connect up to two IDE devices in any combination Pin Signal Pin Signal 401 39 1 IDERST1 2 GND sae 3 PD_7 4 PD_8 oo 5 PD_6 6 PD_9 z 7 PD_5 8 PD_10 oo 9 PD_4 10 PD_11 11 PD_3 12 PD_12 Ba 13 PD 2 14 PD 13 ae 15 PD_1 16 PD_14 Ga 17 PD 0 18 PD 15 ae 19 GND 20 KEY oo 21 PDREQ 22 GND Be 23 PIOW 24 GND T 25 PIOR 26 GND 2 l1 27 PDRDY 28 GND 29 PDACK 30 GND 31 IRQI4AR 32 NC 33 PD_A1 34 P_ATA66 35 PD AO 36 PD A2 37 PCS1 38 PCS 3 39 HD_LED1 40 GND If two drives are connected to a single cable the jumper on the second drive must be set to slave mode Refer to the drive documentation supplied by the vendor for the jumper settings VB7007 User Manua
10. 38 First Second Third Boot Device usrrusernvsseressserrsssseerssseressseresssererssesenssesennse 38 Boot Other Device rssrersserersseresssesesssesresssevessseresssesesssssrersserersseresssesessseresseserener 38 Boot Up NumLock Status innnnsrronssrersssrrrsvsrrnssseressserenssseressseressseressssrersssresssssresee 38 Typematic Rate Setting ssoeseevsseevvsevrssverssrrrssresssresssresseessserssseessseersseersserssseer 38 Typematic Rate Chars Sec nnsssuseresserssseerssseersssseerssseeesssseresssererssesersseserssseenn 39 Typematic Delay MSOC n nnnnnnnssrensserersserenssserssssrerssseressssreessseressseressserersseserssssenn 39 Security Option ss usesesesesseressseesserssserssserssseersserrsseessseessseessseesssverssesssseessee 39 MPS Version Control for OS serersse rssseersssseressssresssssenssseressseresssererssesessssseeese 39 Display Full Screen Logo s ssseressseressseersssseesssseressssressssrenssseeessseressserersseserssereneee 39 Summary Screen Show nseesseeressseressseresssererssererssseressseesssseressseressseressssrersssensseee 39 CPU FG ALUN Gress sccifsscssncssssnsssoassccsssspacoassssasuss sbausccSesoosentsdanvuidssansseeavosscsasonsnsssusassssovassssed 40 Thermal Management ss ssseressseressseressseresssssesssseresssssesssssenssseresssererssererssesersessenn 40 Hard Disk Boot Priority ss usrevsseresssereesseerrssseressseressssrenssseressseressserensssrensssseenee 41 Advanced Chips
11. Reserved The IRQ will be reserved for further requests VB7007 User Manual The PC Health Status displays the current status of all of the monitored hardware devices components such as CPU voltages temperatures and fan speeds VB7007 User Manual uto By SPD 2T 1T 2T1 4T Auto Enabled 0 20 DRAM Clock The chipset supports synchronous and asynchronous mode between host clock and DRAM clock frequency Settings By SPD 200 MHz 266 MHz DRAM Timing The value in this field depends on the memory modules installed in your system Changing the value from the factory setting is not recommended unless you install new memory that has a different performance rating than the original modules Settings Manual By SPD VB7007 User Manual SDRAM CAS Latency This item adjusts the speed it takes for the memory module to complete a command Generally a lower setting will improve the performance of your system However if your system becomes less stable you should change it to a higher setting This field is only available when DRAM Timing is set to Manual Settings 1 5 2 2 3 2 5 4 3 5 Bank Interleave Set the interleave mode of the SDRAM interface Interleaving allows banks of SDRAM to alternate their refresh and access cycles One bank will undergo its refresh cycle while another is being accessed This improves performance of the SDRAM by masking the refresh time of each bank This fiel
12. Two fan connectors CPU and SYS One ATX power connector VB7007 User Manual System Monitoring and Management e AC power failure recovery e RTC timer e Wake on LAN keyboard and mouse Supported OS e Windows 2000 e Windows XP e Windows CE e Windows XPe e Linux BIOS e Award BIOS e SPI 4 8Mbit flash memory Operating Environment e Temperature range 0 C 50 C e Humidity range 0 95 Form Factor e Mini ITX 17 cm x 17 cm Relative humidity and non condensing VB7007 User Manual ATX Power VIA C7 D processor KB MS SYS Fan CPU Fan 7 a pongpa DDR2 Memory slot J1 FIR CN700 North Bridge Buzzer COM3 SMBus COM4 J3 COM2 DIO Inverter PVDD IVDD_SEL VT8237S South Bridge IDE Battery Front Panel Clear CMOS Front Audio sSppIF PCI SATA USB 0 1 LVDS Panel USB 23 VB7007 User Manual PS 2 Mouse Parallel port RJ 45 port a lt Line in w am lt Line Out O lt mic n VGA port COM port USB 2 0 ports PS 2 Keyboard VB7007 User Manual This chapter provides you with information about hardware installation procedures It is recommended to use a grounded wrist strap before handling computer components Electrostatic discharge ESD can damage some components VB7007 User Manual The VIA VB7007 mainboard is packaged with a standard VIA C7 D 1 5 GHz NanoBGA2
13. Utilities CD To start using the CD insert the CD into the CD ROM or DVD ROM drive The CD should run automatically after closing the CD ROM or DVD ROM drive The driver utilities and software menu screen should then appear on the screen If the CD does not run automatically click on the Start button and select Run Then type D Setup exe For Linux drivers click the right button on mouse and click open Linux drivers are located in the Driver folder PA Note EA D might not be the drive letter of the CD ROM DVD ROM in your system VB7007 User Manual O VIA 4in1 Drivers Contains VIA ATAPI Vendor Support Driver enables the performance enhancing bus mastering functions on ATA capable Hard Disk Drives and ensures IDE device compatibility AGP VxD Driver provides service routines to your VGA driver and interface directly to hardware providing fast graphical access IRQ Routing Miniport Driver sets the system s PCI IRQ routing sequence and VIA INF Driver enables the VIA Power Management function Includes V RAID and RAID tools O VIA Graphics Driver Enhances the onboard VIA graphic chip WinXP and Linux Fedora Core 4 drivers are provided O VIA USB 2 0 Driver Enhances VIA USB 2 0 ports O VIA GigaLAN Driver Enhances the onboard VIA VT6130 10 100 1000M PCIe Gigabit LAN chips and the VIA VT6122 Gigabit LAN chip WinXP and Linux Fedora Core 4 drivers are provided O VIA L
14. CP and EPP modes simultaneously Settings SPP EPP ECP ECP EPP EPP Mode Select EPP Enhanced Parallel Port comes in two modes 1 9 and 1 7 EPP 1 9 is the newer version of the protocol and is backwards compatible with most EPP devices If your EPP device does not work with the EPP 1 9 setting try changing the setting to EPP 1 7 Settings EPP 1 9 EPP 1 7 ECP Mode Use DMA ECP Extended Capabilities Port has two DMA channels that it can use The default channel is 3 However some expansion cards may use channel 3 as well To solve this conflict change the ECP channel to 1 Select a DMA channel for the port Settings 1 3 Onboard Fast IR Enables or disables the infrared port Settings Enabled and Disabled Fast IR IRQ Set this field to reserve an IRQ for the Fast IR port This field is only available if Onboard Fast IR is enabled Settings 3 4 Fast IR DMA Set this field to choose the DMA channel This field is only available if Onboard Fast IR is enabled Settings 6 5 VB7007 User Manual Enabled DOM support UDMA66 Settings Disabled Enabled IDE DMA Transfer Access Settings Disabled Enabled VB7007 User Manual Enabled High Speed Menu Level Enabled Enabled Enabled USB 1 0 Controller Enable or disable Universal Host Controller Interface for Universal Serial Bus Settings Disabled Enabled USB 2 0 Controller Enable or disable Enhanced
15. Disabled Disabled Disabled Press Enter Onboard IDE Channel 1 and 2 The integrated peripheral controller contains an IDE interface with support for two IDE channels Settings Disabled Enabled IDE Prefetch Mode This allows your hard disk controller to use the fast block mode to transfer data to and from the hard disk drive Block mode is also called block transfer multiple commands or multiple sector read write Settings Disabled Enabled IDE HDD Block Mode Automatic detection of the optimal number of block read writes per sector the drive can support Settings Disabled Enabled TUE VB7007 User Manual SATA Controller Settings Disabled Enabled SATA Controller Mode Controls the features of the Serial ATA controller within the South Bridge Serial ATA is the latest generation of the ATA interface Serial ATA hard drives deliver transfer speeds of up to 300MB sec Settings Description IDE Supports two PATA hard disk drives Disables RAID and AHCI function RAID Only SATA supports RAID and AHCI function AHCI Enable the AHCI function such as Native Command Queuing and Hot Plug function Azalia HDA Controller Settings Auto Disabled LAN Controller Settings Enabled Disabled OnChip LAN Boot ROM Decide whether to invoke the boot ROM of the onboard LAN chip Settings Enabled Disabled Giga LAN Boot ROM Decide whether to invoke the boot ROM of the onboard GigaLAN chip
16. Host Controller Interface for Universal Serial Bus Settings Disabled Enabled USB Operation Mode Auto decide USB device operation mode Settings Description Full Low Speed All of USB Device operated on full low speed mode High Speed If USB device was high speed device then it operated on high speed mode a VB7007 User Manual USB Keyboard Function Enable or disable Legacy support of USB Keyboard Settings Disabled Enabled USB Mouse Function Enable or disable Legacy support of USB Mouse Settings Disabled Enabled USB Storage Function Enable or disable Legacy support of USB Mass Storage Settings Disabled Enabled VB7007 User Manual 1831 Disabled Disabled Suspend gt Off CInstant Off Auto Off Press Enter ACPI Suspend Type Settings Description S1 POS S1 Power On Suspend POS is a low power state In this state no system contexts system context CPU or chipset is lost and hardware maintains all S3 STR S3 Suspend To RAM STR is a power down state In this state wakeup event occurs power is supplied only to essential components such as main memory and wakeup capable devices The system context is saved to main memory and context is restored from the memory when a S1 amp S3 Depends on the OS to select S1 or S3 HDD Power Down Set the length of time for a period of inactivity before powering down the hard disk
17. VB 007 Mini ITX Mainboard Manual Copyright and Trademarks Copyright O 2009 VIA Technologies Incorporated All rights reserved No part of this document may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of VIA Technologies Incorporated All trademarks are the property of their respective holders PS 2 is a registered trademark of IBM Corporation Disclaimer No license is granted implied or otherwise under any patent or patent rights of VIA Technologies VIA Technologies makes no warranties implied or otherwise in regard to this document and to the products described in this document The information provided in this document is believed to be accurate and reliable as of the publication date of this document However VIA Technologies assumes no responsibility for the use or misuse of the information in this document and for any patent infringements that may arise from the use of this document The information and product specifications within this document are subject to change at any time without notice and without obligation to notify any person of such change Regulatory Compliance FCC B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device pursuant to pa
18. afe default table only for Option Page Setup Menu F5 F6 Load Optimized defaults F10 Save all the CMOS changes and exit VB7007 User Manual The main menu displays all the BIOS setup categories Use the lt Left gt lt Right gt and lt Up gt lt Down gt arrow keys to select any item or sub menu Descriptions of the selected highlighted category are displayed at the bottom of the screen The small triangular arrowhead symbol next to a field indicates that a sub menu is available see figure below Press lt Enter gt to display the sub menu To exit the sub menu press lt Esc gt Standard CMOS Features gt Advanced BIOS Features gt Advanced Chipset Features gt Integrated Peripherals gt Power Management Setup gt PnPvPCI Configurations gt PC Health Status gt Frequency Voltage Control Load Optimized Defaults Set Supervisor Password Set User Password Save amp Exit Setup Exit Without Saving Time Date Hard Disk Type VB7007 User Manual The BIOS setup program provides a General Help screen You can display this screen from any menu sub menu by pressing lt F1 gt The help screen displays the keys for using and navigating the BIOS setup Press lt Esc gt to exit the help screen VB7007 User Manual The Main Menu contains thirteen setup functions and two exit choices Use arrow keys to select the items and press lt Enter gt to accept or enter Sub
19. al items and it is strongly recommended to leave the default settings as is unless you are an experienced user PNP OS Installed Settings Description No BIOS will initialize all the PnP cards Yes BIOS will only initialize the PnP cards used for booting VGA IDE SCSI The rest of the cards will be initialized by the PnP operating system Na VB7007 User Manual Reset Configuration Data Settings Description Disabled Default setting Enabled Resets the ESCD Extended System Configuration Data after exiting BIOS Setup if a newly installed PCI card or the system configuration prevents the operating system from loading Resources Controlled By Enables the BIOS to automatically configure all the Plug and Play compatible devices Settings Description Auto ESCD BIOS will automatically assign IRQ DMA and memory base address fields Manual Unlocks IRQ Resources for manual configuration Assign IRQ for VGA Assign IRQ for VGA devices Settings Disabled Enabled Assign IRQ for USB Assign IRQ for USB devices Settings Disabled Enabled VB7007 User Manual PCI Device PCI Device PCI Device PCI Device CPCI Device PCI Device CPCI Device IRQ Resources list IRQ 7 9 10 11 12 14 15 for users to set each IRQ a type depending on the type of device using the IRQ Settings PCI Device For Plug and Play compatible devices designed for PCI bus architecture
20. ard functions This section will explain how to change the settings of the mainboard functions using the jumpers Clear CMOS Connector CLEAR CMOS The onboard CMOS RAM stores system configuration data and has an onboard battery power supply To reset the CMOS settings set the jumper on pins 1 and 2 while the system is off Return the jumper to pins 2 and 3 afterwards Setting the jumper while the system is on will damage the mainboard Setting 1 2 3 Normal Operation ON ON OFF Clear CMOS setting OFF ON ON Caution Except when clearing the RTC RAM never remove the cap on CLEAR CMOS jumper default position Removing the cap will cause system boot failure Avoid clearing the CMOS while the system is on it will damage the mainboard Voltage Selector for COM2 3 4 J3 2 1 This VCC selector is to determine the input voltage of each COM connector Setting 1 2 3 5V ON ON OFF 12V OFF OFF ON VB7007 User Manual Panel Power Selector PVDD Setting 1 2 3 5V ON ON OFF 3 3V OFF ON ON Inverter Power Selector IVDD SEL Setting 1 2 3 5V ON ON OFF 12V OFF ON ON VB7007 User Manual Peripheral Component Interconnect PCI SLOT The PCI slot allows you to insert a PCI expansion card First unplug the power supply before adding or removing expansion cards Read the documentation for the expansion card to see if any
21. ary PIO Settings Auto Mode 1 Mode 2 Mode 3 Mode 4 Primary UDMA Settings Disabled Auto VB7007 User Manual Press Enter Press Enter Disabled Enabled Enabled Enabled USB HDD1 CDROM Hard Disk Enabled 0n Disabled Setup 1 41 Disabled Disabled Virus Warning Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection Settings Description Enabled Turns on hard disk boot sector virus protection Disabled Turns off hard disk boot sector virus protection Note If this function is enabled and someone attempt to write data into this area BIOS will show a warning message on the screen and alarm beep CPU L1 amp L2 Cache Settings Disabled Enabled VB7007 User Manual CPU L2 Cache ECC Checking This feature facilitates error detection correction when data passes through Level 2 cache Settings Disabled Enabled Quick Power On Self Test Shortens Power On Self Test POST cycle to enable shorter boot up time Settings Description Disabled Standard Power On Self Test POST Enabled Shorten Power On Self Test POST cycle and boot up time First Second Third Boot Device Set the boot device sequence as BIOS attempts to load the disk operating system Settings Description Removable Boot from external drive Hard Disk Boot from the HDD CDROM Boot from CDROM USB CDROM Boot fro
22. cestsatacaiass25 nsccolbsecreishoneveisteretascbdeastosbasenasibaensaetioveisio 60 Assign IRQ for USB n esseessseressseressserersseressssersssseesssssressssresssseresssererssssersssserssssren 60 IRQ Resources msrsssssrrssrsserserssesseessrsseeseessessreseessersressessersesserserssesserseessessesssessens 61 PC Health Statuskusssassuskneu sekten sis nana N 62 Frequency Voltage Control ssessserersserrsssserssssrerssserrsssererssseressseressseresssesesssssreese 63 DRAM CD 63 DRAM Timing eossresserssseersserssseerssresssresssresseresserssserssseersseessseersseesssrersseessssesssessseenes 63 SDRAM CAS Latency rusersseessseesssresssresserssserssserssseessserssseersseersseersssersssersseessssersee 64 Bank Interleave eessescsssssssessseesssecesseesnseesnscesuscesnsecsusecsneeenncecsueesnsseseneesneeeseseesee 64 Precharge to Active Tip nnnssrensserersssrrrsvevrnsssressssreessseressseressseressserersssrerssesereee 64 Active to Precharge Tras s ssrrsssresssresssresssresssresssrssssrssssrssssrssserssseessseesssersssenn 64 Active t CMD CINCO seaicicessscssstscisccessctetessccansccdcnsssecodeagessasesancessocasesseuteaedbensdasctoeds 64 REF to ACT REF TO ses ccosvccsvessescsoocesecssscoetspevsscessecauvcsecsvenseodseovbsecaytasseseetscsscente 65 ACT 0 to ACT 1 TRRD nenene 65 Read to Precharge Trtp n nusessermsserssrssrssrsssessseesssessessrsssesssrsssrsssern 65 Write to Read CMD TW innnnnnr
23. changes to the system are necessary PCI Interrupt Request Routing The IRQ interrupt request line are hardware lines over which devices can send interrupt signals to the microprocessor The PCI amp LAN IRQ pins are typically connected to the PCI bus INT A INT_D pins as follows Order 1 Order 2 Order 3 Order 4 PCI slot INT_B INT_C INT_D INT A VB7007 User Manual This chapter gives a detailed explanation of the BIOS setup functions VB7007 User Manual Power on the computer and press lt Delete gt during the beginning of the boot sequence to enter the BIOS setup menu If you missed the BIOS setup entry point restart the system and try again VB7007 User Manual Keys Description Move to the previous item Move to the next item Move to the item in the left side Move to the item in the right side Select the item Jumps to the Exit menu or returns to the main menu from a Esc submenu A Increase the numeric value or make changes Decrease the numeric value or make changes Down Increase the numeric value or make changes Decrease the numeric value or make changes DIER VB7007 User Manual Keys Description General help only for Status Page Setup Menu and Option Page Setup Menu F Restore the previous CMOS value from CMOS only for Option Page Setup Menu Load the default CMOS value from Fail S
24. d is only available when DRAM Timing is set to Manual Settings Disabled 2 Bank 4 Bank 8 Bank Precharge to Active Trp This field controls the length of time it takes to precharge a row in the memory module before the row becomes active Longer values are safer but may not offer the best performance This field is only available when DRAM Timing is set to Manual Settings 2T 5T Active to Precharge Tras This field controls the length of time it a row stays active before precharging Longer values are safer but may not offer the best performance This field is only available when DRAM Timing is set to Manual Settings 5T 207 Active to CMD Trcd This field is only available when DRAM Timing is set to Manual Settings 2T 5T VB7007 User Manual REF to ACT REF Trfc This field is only available when DRAM Timing is set to Manual Settings 08T 71T ACT 0 to ACT 1 TRRD This field is only available when DRAM Timing is set to Manual Settings 2T 5T Read to Precharge Trtp Settings 2T 3T Write to Read CMD Twtr Settings 1T 2T 27 37 Write Recovery Time Twr Settings 2T 5T RSAIT Mode Settings Auto Manual RSAIT Selection This field is only available when RSAIT Mode is set to Manual Input should be a hexadecimal number Auto Detect PCI Clk Settings Enabled Disabled Spread Spectrum When the mainboard s clock genera
25. e for air convection hence protects the equipment from overheating Do not cover the openings Make sure the voltage of the power source and adjust properly 110 220V before connecting the equipment to the power inlet Place the power cord in such a way that people cannot step on it Do not place anything over the power cord Always unplug the power cord before inserting any add on card or module All cautions and warnings on the equipment should be noted Never pour any liquid into the opening Liquid can cause damage or electrical shock If any of the following situations arises get the equipment checked by authorized service personnel o The power cord or plug is damaged o Liquid has penetrated into the equipment o The equipment has been exposed to moisture o The equipment has not worked well or you cannot get it work according to User s Manual o The equipment has dropped and damaged o The equipment has obvious sign of breakage Do not leave this equipment in an environment unconditioned or in a storage temperature above 60 C 140 F The equipment may be damaged Box Contents 1 x VB7007 mainboard 1 x ATA 66 100 133 IDE ribbon cable 1 x I O bracket 1 x Driver Utility CD OoOoOod 1 N Specifications 0 eee Mainboard Specifications Mainboard Layout Back Panel Layout Installation u s CPU Fan and System Fan CPUFAN and SYSFAN Memory Module Installation
26. edures Locate the DIMM slot in the motherboard Unlock a DIMM slot by pressing the retaining clips outward Align a DIMM on the socket such that the notch on the DIMM matches the break on the slot Firmly insert the DIMM into the slot until the retaining clips snap back in place and the DIMM is properly seated geneween in I RU 4 a HI 7 VA OnE it ve Available DDR2 SDRAM Configurations Refer to the table below for available DDR2 SDRAM configurations on the mainboard Slot Module Size Total DIMM1 64 MB 128 MB 256 MB 512 MB 1 GB 64 MB 1 GB Maximum supported system memory 64 MB 1 GB VB7007 User Manual The VIA VB7007 mainboard supports a conventional ATX power supply for the power system Before inserting the power supply connector always make sure that all components are installed correctly to ensure that no damage will be caused ATX Power a 320 m 000 99900 nm 8 g tere ooooa0000 onoonoooo0000000000 VB7007 User Manual ATX 20 Pin Power Connector To connect the power suppl
27. eivinnentneindetj hes 53 USB 20 COMMONER ccccesscssoveseescsssvesedersveuscesecascussezersseuesesscaseunsesesasecssczssgostevezesdects 53 USB Operation MOC sssesssssecsssecssseescssecesssscecsssscssnsseesnseesnseesssecssaneeesasecs 53 USB Keyboard Function esesussresseerssseeressseerssserressseressseressseressserersssrensssrersssee 54 USB Mouse Function urensnvrvssrerevevevsrrrsrvevsvssrevevevsvsssrsevevsssssesevevsssssesevevsssesesever 54 USB Storage Function neesseseesereesseveserseseerevserssserssseanevensssveversevesnesessessenesseanese 54 Power Management Setup s se esevseeseseeeseesseessseessseessseessseesseeesseresssressee 55 ACPI Suspend Type mnnessvnssseressseresssererssveressseressseeessssresssseenssseresssererssesersssserssssren 55 HDD Power DOWn nessesseesseesseessrssersseesssesseessersseesseesseesseesseesseesseesseesseesseesssesssesee 55 Power Management Timer isessersseesssresssersseersserrsserssssersseessseersseesssressssessseene 56 Video Off Option isseussvevseeresseressservassereesssersssseeessssresssssesssseressseressserersssserssssenr 56 Power Off by PWRBTN isssessseressseressservsssseerssseressssresssseenssseressseressseserssssersssreneee 56 Run VGABIOS if S3 Resume ssssesrnsssrrsssseresesernsssseessseresssererssererssseersssererssssenne 56 AC Loss Auto Restart n ss eseesseeseeseeseeseeeseeseeessessseessseessseessseessseersseer 56 Peripherals Activities n
28. ensersessensesseseessessene 23 JUM PES Hi 24 Clear CMOS Connector CLEAR CMOS rerrerressesersersersersevsevsvsseserserserserserser 24 Voltage Selector for COM2 3 4 J3 2 1 nnnnssrnssservssssrvesssrvessseressserersseserssssenn 24 Panel Power Selector PVDD ob Peripheral Component Interconnect PCI SLOT snnneeossseressserersserersserensse 26 PCT Interrupt Request Routing n sssressrsvserrsserrsseersseerssrersseesssressseessessseessssenes 26 3 BIOS Setup mumssesseessseessseessserssseessseessseersseesssresssessssressessseessseresseessseersseersseessseer 27 Entering the BIOS Setup Menu sssessserssseernsssrrrssseressserenssserssssressseressseresssssreese 28 Control KEySusnnnnsnnni nuni nnn nnn nnn ERREN R ENS 29 Navigating the BIOS Menus sreusseressseressseeessssersssseersssseressseressseressserersssreesssseesee 31 Getting Help nnnnsrrnsssrnssrrsssrsssrsssrrsssersssrsssesssresssresssresssrssserssserssserssseessseessseessseesssren 32 ME EE NE 33 Standard CMOS Features nnssensserevsseressseresssererssseerssseresssseressseressseressssrerssseenssses 33 Advanced BIOS Features n urrmssrsssesssrssessrsssssrsssrsssesssersseesssesseessen 33 Advanced Chipset Features ussrserssrvssrvssseressseeessseeressseressserersseversseseer 33 Integrated Peripherals uusssrseessseerssssersssseressssserssseeessseresssesersseserssseeen 33 Power Management Setup nnssessrevssresserrsserrsserrsserrsseersseersseesss
29. eresssversssserrssssressssrenssseressseresssererssesersserenn 49 SuperIO Device errsersserrsersserssersserssersseesssesssenssenssenssenssenseenseenssenssenssenssenssenssenssenssenee 50 Onboard Serial Port 1 2 3 4 srnrevrvvevvvsrvvsvrvrssrsvssevrssevrssesrssesessessssesrssesessesnser 50 Onboard Parallel Port cscce ccsccesssessssssressersvsssseesssesctepsvenseneesesacenodepsussussosaseecousesess 50 Parallel Port Mode n mmernvserseoveersrrvrrssersrnvervsersrasessserseaversserserserssersesseesserseessenser 51 EPP Mode Select nnseenssvsrervrsrenverssrsverserssrssenserssessenserssessenserssessenserssensenssrssensenser 51 ECP Mode Use DMA n serserserserrevsesvesersersersersevsevsersessesersersersersevsessessvssesersersersessere 51 Onboard F st IR Lun nnnesstneeskiksenatanemneenbenkikekend 51 Fast IR IRO sauna as aR R EAER 51 Fast IR DIMA ie scsssssssavsessisceseteaszetazsesdesesscsdqcvevestesastestestereslspaciavleatstoriesteateleoaeiedeeterees 51 VIA OnChip IDE De VICE sss secsssescessecesssteccsstecesssecessseeessneessnseetsnseessnseesnsnseesanetsa 52 DOM support UDMA66 esrerssrevssresssresseresseersserssseersseersseessseesssresssresssresssrsssseres 52 IDE DMA Transfer ACCESS nrssesrersersresrerserssenserserssersersseserserssenserserssenserssessensenee 52 USB Device Setting rn ssesssseresserssveravveranverssvensevenssvvenevenseeresenesesnevsenessenersenssserersenneee 53 USB T 0 Controll n uuuunnannninensetinnnine
30. et Features ss usersrrsvrvseesseessseeresseeresssererssevesesseenn 42 Display C rd Prorityuauugsnssngtgnmadeselsiiinsidvdvidrnieiseiisen 42 Video RAM Cacheable isssossserevsseressservssssersssssressserenssssenssseeessssresssererssesersessenn 42 AGP Driving Control ussensseressseressseresssveressseresssesesssseesssseesssseressseressseserssssersssseen 42 AGP Driving Value nseesseeesseeressseressseressseresssseesssseerssssresssseenssseeessseresssesersssserssssenn 43 Select Display Device us usssvseressseressseeessseeesssseressseeesssseressseresssererssesensseee 43 Panel Type nnssonsseressssrvessseressseressserenssrersssrensssrenssseeesssseenssssesssseeessseresssererssssessssseesee 43 AGP amp P2P Bridge Control jss usseressseressseressseresssseressseesssereessseressseresssesensseserssssenn 44 AGP Aperture SIZE iasccsccasccusccaiccusccusccusccdsecuseddsendseadscndscadeccd eadeccdscadesndscadssnuisadsccuetad 44 AGP3 0 MOQ Einiiniinnisiinninnieinninaninaninani nann ana 44 AGP Fast Wear 44 AGP 3 0 Calibration Cycle ssssssssssssssssssssssssssestrrsssssssssseeetrsssssssssssseneernensssss 45 VGA Share Memory Size issessseressseressservsssversssseressseresssseenssseressserersseserssesersserenn 45 Direct Frame Buffer osssserosssresssrnsssrsssersssesssersssresssersssresssrrsssrssssrssssrssssesssernee 45 opera 45 Dithenng uunsssneseianninignmnijavne djinun dreiv guests 45 GPU 8 PET BUS C nt
31. etup is run This prevents an unauthorized person from changing any part of your system configuration There are two types of passwords you can set A supervisor password and a user password When a supervisor password is used the BIOS Setup program can be accessed and the BIOS settings can be changed When a user password is used the BIOS Setup program can be accessed but the BIOS settings cannot be changed To set the password type the password up to eight characters in length and press lt Enter gt The password typed now will clear any previously set password from CMOS memory The new password will need to be reentered to be confirmed To cancel the process press lt Esc gt To disable the password press lt Enter gt when prompted to enter a new password A message will show up to confirm disabling the password To cancel the process press lt Esc gt VB7007 User Manual Additionally when a password is enabled the BIOS can be set to request the password each time the system is booted This would prevent unauthorized use of the system See Security Option in the Advanced BIOS Features section for more details VB7007 User Manual gt Standard CMOS Features gt Frequency Voltage Control gt Advanced BIOS Features Load Optimized Defaults gt Advanced Chipset Features Set Supervisor Password gt Integrated Peripherals Set User Password gt Power Management Setup gt PnP PCI Configurations Exit W
32. full screen logo during BIOS boot up process Settings Disabled Enabled Summary Screen Show Show summary screen Settings Disabled Enabled VB7007 User Manual Thermal Monitor 11 Thermal Management This item sets CPU s thermal control rule to protect CPU from overheat Settings Description Thermal Monitor 1 On die throttling VB7007 User Manual Bootable Add in Cards This is for setting the priority of the hard disk boot order when the Hard Disk option is selected in the First Second Third Boot Device menu item VB7007 User Manual PCI Slot Press Enter Press Enter Menu Disabled Auto CRT Ses 02 Caution The Advanced Chipset Features menu is used for optimizing the chipset functions Do not change these settings unless you are familiar with the chipset Display Card Priority Settings PCI Slot AGP Video RAM Cacheable Settings Disabled Enabled AGP Driving Control Settings Auto Manual TUE VB7007 User Manual AGP Driving Value This option can only be altered if AGP Driving Control is set to Manual Input is expected as hexidecimal Select Display Device Settings CRT LCD CRT amp LCD Panel Type Settings Description 00 640 x 480 01 800 x 600 02 1024 x 768 03 1280 x 768 04 1280 x 1024 VB7007 User Manual 128M1 8X1 Auto Enabled 64M1 Enabled DIQ
33. inux RAID Driver Support for RAID devices For Linux Fedora Core 4 and patch guide to enable PATA IDE DMA mode for VIA South Bridges
34. ithout Saving gt PC Health Status Save Data to CMOS Entering Y saves any changes made and exits the program Entering N will cancel the exit request VB7007 User Manual gt Standard CMOS Features gt Frequency Voltage Control gt Advanced BIOS Features Load Optimized Defaults gt Advanced Chipset Features Set Supervisor Password gt Integrated Peripherals Set User Password gt Power Management Setup Save amp Exit Setup gt PnP PCI Configurations Exit Without Saving gt PC Health Status Abandon all Data Entering Y discards any changes made and exits the program Entering N will cancel the exit request VB7007 User Manual This chapter gives you brief descriptions of each mainboard driver and application You must install the VIA chipset drivers first before installing other drivers such as VGA drivers The applications will only function correctly if the necessary drivers are already installed VB7007 User Manual Getting Started VIA VB7007 Developer kits include a driver CD that contains the drivers and software for enhancing the performance of the mainboard Regular kits do not include a driver CD However the latest drivers can be downloaded from http www via com tw 080000 A A Note The driver utilities and software are updated from time to time The latest updated versions are available at http www via com tw Running the Driver
35. l a F D GE 000 MC fee E j B i USB_2 3 USB 0 1 USB Pin Connector USB 0 1 and USB 2 3 The mainboard provides two 10 pin USB pin connectors allowing up to four additional USB 2 0 ports USB 0 1 Pin Signal Pin Signal 1 VUSBO 2 VUSBO 3 USBD TO 4 USBD_T1 5 USBD_T0 6 USBD_T1 7 GND 8 GND 9 KEY 10 GND USB_2 3 Pin Signal Pin Signal 1 VUSBO 2 VUSBO 3 USBD T2 4 USBD T3 5 USBD_T2 6 USBD_T3 7 GND 8 GND 9 KEY 10 GND VB7007 User Manual Digital I O Connector DIO General purpose digital input and output Pin Signal Pin Signal 1 5V 2 12V 3 GPO1 4 GPI4 5 GPO7 6 GPI13 7 GPO26 8 GPI14 9 GPO27 10 GPI15 11 GND 12 GND go G FRERE SO ag Fed HE 8 00000 coms 1 ng com Sn elg com Er gag o m 88 H 29088 B lt smeus Doosooo000000 EEEE a GE 0005000 00o0ou0oo0o0o0u00 VB7007 User Manual
36. m USB CDROM Network Boot from network drive Disabled Disable the boot device sequence Boot Other Device Enables the system to boot from alternate devices if the system fails to boot from the First Second Third Boot Device lists Settings Description Disabled No alternate boot device allowed Enabled Enable alternate boot device Boot Up NumLock Status Set the NumLock status when the system is powered on Settings Description Off Forces keypad to behave as arrow keys On Forces keypad to behave as 10 key Typematic Rate Setting Enable Typematic Rate function Settings Disabled Enabled VB7007 User Manual Typematic Rate Chars Sec This item sets the rate characters second at which the system retrieves a signal from a depressed key Settings 6 8 10 12 15 20 24 30 Typematic Delay Msec This item sets the delay between when the key was first pressed and when the system begins to repeat the signal from the depressed key Settings 250 500 750 1000 Security Option Selects whether the password is required every time the System boots or only when you enter Setup Settings Description Setup Password prompt appears only when end users try to run BIOS Setup System Password prompt appears every time when the computer is powered on and when end users try to run BIOS Setup MPS Version Control for OS Settings 1 1 1 4 Display Full Screen Logo Show
37. menu gt Standard CMOS Features gt gt gt Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP PCI Configurations PC Health Status gt Frequency Voltage Control Load Optimized Defaults Set Supervisor Passuord Set User Password Save amp Exit Setup Exit Without Saving Time Date Hard Disk Type Use this menu to set basic system configurations Advanced BIOS Features Use this menu to set the advanced features available on your system Advanced Chipset Features Use this menu to set chipset specific features and optimize system performance Integrated Peripherals Use this menu to set onboard peripherals features Power Management Setup Use this menu to set onboard power management functions ee m VB7007 User Manual PnP PCI Configurations Use this menu to set the PnP and PCI configurations PC Health Status This menu shows the PC health status Frequency Voltage Control Use this menu to set the system frequency and voltage control Load Optimized Defaults Use this menu option to load BIOS default settings for optimal and high performance system operations Set Supervisor Password Use this menu option to set the BIOS supervisor password Set User Password Use this menu option to set the BIOS user password Save amp Exit Setup Save BIOS setting changes and exit setup Exit Without Saving
38. processor The VIA C7 D 1 5 GHz processor requires a heatsink with fan to provide sufficient cooling VIA C7 D processor CPU_Fan SYS_Fan p z g FATTETTTT PEEL lo m CPU Fan and System Fan CPUFAN and SYSFAN The CPU_FAN CPU fan and SYS_FAN system fan run on 12V and maintain system cooling When connecting the wire to the connectors always be aware that the red wire positive wire should be connected to the 12V The black wire is Ground and should always be connected to GND Pin Signal 1 FANIO 2 12V 3 GND VB7007 User Manual Memory Slot DDR2 DIMM The VIA VB7007 mainboard has one 240 DIMM slot for DDR2 667 533 SDRAM memory modules and supports memory sizes up to 1 GB DDR2 Memory slot 1 GB SDRAM only supported with 64 MB x 8 bit x 16 configuration 7007 User Manual DDR2 SDRAM Module Installation Proc
39. rR GND VB7007 User Manual Front Audio F AUDIO This connector allows you to connect a front audio panel to the mainboard Pin Signal Pin Signal 9 1 1 MIC2 IN L 2 AGND EPER 3 MIC2 IN R 4 3 3V 5 HP OUT R 6 NC 10 2 7 NC 8 KEY 9 HP OUT L 10 NC g0 _ Hed po GE 0 00000 2 8 g EF k EE g Inverter gt B 88 LVDS Panel VB7007 User Manual LVDS Connector PANEL CONN Pin Signal Pin Signal 2 11 1 A4 L 2 PVDD i 3 ML 4 PVDD 5 GND 6 GND 7 AS L 8 GND 9 AS L 10 AO L 11 GND 12 AO L 13 AGL 14 GND 40 L 39 15 A6L 16 ALL 17 GND 18 ALL 19 CLK2 L 20 GND 21 CLK2L 22 A2 L 23 GND 24 A2 L 25 A7L 26 GND 27 A7L 28 CLK1 L 29 NC 30 CLKL L 31 NC 32 GND 33 NC 34 A3 L 35 NC 36 A3 L 37 NC 38 SPCLK1 39 NC 40 SPD1 LVDS Inverter INVERTER Pin Signal VCC VCC BAKLITE NC BAKLITE SMBUS OUT GND COWL ID MR WIN eR GND VB7007 User Manual The mainboard provides jumpers for setting some mainbo
40. resssresssrssssessssenes 33 PnP PCI Configurations issssrssersserssssssssesssessvssssssssssrses 34 PC Health Status nn umrnuitervnmubeneeeniteedntvetuite lide 34 Frequency Voltage Control s usssensresseerssseersssseerssssersssseressseressserersssresssseeeese 34 Load Optimized Defaults ns euserenservvsseeressservssserrssseressseressserersserersssrersssernse 34 Set Supervisor PaSSWOrd nsssssrmssrssssrsssrsssersssersssersssersssressseesssresssresssrnsssrnnser 34 Set User Password incisscioiisscessccciasssicsssscesensssosieslbuesscoiueestseidcendssddonedeestssiooasiecoasts 34 Save 8L Exit Set Prans ann 34 Exit Without Saving us usersreseesseeessseersssseressseresssssesssseressseresssererssssersssseneee 34 Standard CMOS Features n srersserensseerssssersssseressssrersssernssseressseresssererssesenssssesssseenr 35 D 35 MEL 35 IDE ChaMelo na na Ra Rn n 36 Advanced BIOS Features nss ssrnsssrnsserssserssserssseesssersssrrsssersssresssrrsssrssssrssserssssrsssernee 37 Virus Warning usessesssessessserosserssseersseersseersseessseesssresssresssressseesseessseeseserasseessseersseer 37 CPU L1 amp L2 Cache nssnososeresssesvessseresssererssesessssevessseresssesesssessessserersseresssesesssssreseser 37 CPU L2 Cache ECC Checking ussessseessseressseeesssseesssseerssssersssseressseressssrersssrersseee 38 Quick Power On SElPRAT CS scasccsassesscssssssscsnssenscanssenscanssenycanssenscanstenscenpeanscanpeatyeante
41. rnsrnrervrersrrsvevrrrsrrverssrrsesversserserverrsersersserserseessenee 65 Write Recovery Time Twr in nennsernsersserssersserssersserssersserssersserssersserssersseessensssens 65 RSAIT Mod gecesi na keen 65 RSAIT SelectiOhuuniussnsuneurieseeedleniatleseidaddnmdmnddnd 65 Auto Detect PCI CIK nn nnsensserserverssrrserversserverssrrserverssrssessersserserserrsersersersserseessenee 65 Spread Spectrum mnnnsseressseressseressseressserersserersssrenssseressssresssseressseressseressssrerssssensssee 65 Load Optimized Defaults ussossrrsssvrsssrrsssresssrnsssrsssersssersssrsssersssersssersssreessensser 66 Set Supervisor User PasswWord s userussnnsserrsssesrassseressseressseressserersssrersssserssssenr 67 Save amp Exit Setup n sseeseveseeeeseseseeseeessseesseessseessseessseesssersseersseersseer 69 Exit Without Savinguisssansniaenssieisiudbiegiuiisinduie 70 4 Driver Install ti n asunsesnsesnsnsnieennbespunenbknbknbGnbEen 71 PiverUites er ere Ne rs oP OP nO 72 Getting Started oo eceecceecsseeessesssssessnscsnscesusecsuscesnsesuseesueessueesueeeseeeesneesneesneeesaess 72 Running the Driver Utilities CD nsssserssssrrssersssersssersssrsssrrsssrrsssrrsssresssresssrnns 72 CD Content sa20 EE E EEE EENE E R 73 VB7007 User Manual The compact and highly integrated VIA VB7007 mainboard comes with an integrated VIA C7 NanoBGA2 processor boasting of ultra low power consumption and cool operation VB7007 U
42. rolu uuuanasnetninesniaetaevanuakleissteu dukens 46 VLink Mode Selection msreversevrevserressrssvrersersevsersersvsvrsersersersersersvssesersersersersers 46 VLink 8X Support nseesservesseeressseressserersssrerssseeessseeessssresssssenssseressseresssesersssserssssenn 46 DRDY Timing E 46 Integrated Peripherals m s ussesservvsseressseressseerssseerrssseeesssseessssevessseressserersssserssseenn 47 Onboard IDE Channel 1 and 2 ereseesvesersvrserserrersesvesersersersvrsersvsseserserserserserser 47 IDE Prefetch Mode mssernsresrvrsroveersersrsverrserseesseerserseesserserseesserserssersersesssersenseessenee 47 IDE HDD Block Mode nrnvrorrvrsroverrsrrsrrvsrsssaverserrserseessensenseesserserseersersesssersensernsenee 47 SATA Controller uuuuumuarmmmmiminmnrevmtdassrivissrneemridvtddskssie 48 SATA Controller Mode nnrersersevsesresersveversersevsevserseseesersersersersersessesersvrserserserser 48 Azalia HDA Controller nnsrrrnvresrerrrovevrservroverrserveessrrserseerserserseersersersserseassessenee 48 FAN Controller 48 OnChip LAN Boot ROM nnsessevsssseressseresssererssseesssseensssseessssersssseressseressssrersseserssser 48 Giga LAN Boot RO Misiin nnn R 48 WatchDog Support siisncsccsccsicsctsssssccieasssccbecisiecdeoisesrduendsosdectdnsedgeodonqdeaiteesdaeclioubsetd 49 Watch Dog Timer Select nn essreusservsersseeresssersssseressseerrssseressseressssrerssseerssseenn 49 Watch Dog Count Value nssonssressseresss
43. rt 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his personal expense Notice 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Notice 2 Shielded interface cables and A C power cord if any must be used in order to comply with the emission limits Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Battery Recycling and Disposal Only use the appropriate battery specified for this product Do not re use recharge or reheat an old battery Do not attempt to force open the battery Do not discard used batteries with regular trash Discard used batteries according to local regulations Safety Precautions OGOOO o Always read the safety instructions carefully Keep this User s Manual for future reference Keep this equipment away from humidity Lay this equipment on a reliable flat surface before setting it up The openings on the enclosure ar
44. s Hot Key and Password To select the Password option press lt Page Up gt or lt Page Down gt To set the password enter up to eight digits and press lt Enter gt Settings Hot Key Password PS2KB Wakeup Key Select This feature is only available when Hot Key is chosen in PS2KB Wakeup Select Settings Ctrl F1 Ctrl F2 Ctrl F3 Ctrl F4 Ctrl F5 Ctrl F6 Ctrl F7 Ctrl F8 Ctrl F9 Ctrl F10 Ctrl F11 Ctrl F12 Power Wake Any Key PS2MS Wakeup Key Select Settings Any Button Left Button Right Button PS2 Keyboard Power ON Settings Disabled Enabled VB7007 User Manual PS2 Mouse Power ON Settings Disabled Enabled USB Resume Settings Disabled Enabled PowerOn by PCI Card Enables activity detected from any PCI card to power up the system or resume from a suspended state Such PCI cards include LAN onboard USB ports etc Settings By OS Enabled RTC Alarm Resume Set a scheduled time and or date to automatically power on the system Settings Disabled Enabled Date of Month This field can only be set if RTC Alarm Resume is enabled The field specifies the date for RTC Alarm Resume Resume Time hh mm ss This field can only be set if RTC Alarm Resume is enabled The field specifies the time for RTC Alarm Resume VB7007 User Manual No Disabled Auto ESCD 1 Enabled Enabled i h Note Z This section covers some very technic
45. ser Manual CPU e VIAC7 D 1 5 GHz NanoBGA2 processor with fansink Chipset e VIA CN700 North Bridge e VIA VT8237S South Bridge Graphics e Integrated VIA UniChrome Pro II AGP graphics with 2D 3D and video acceleration Memory e One DDR2 667 533 DIMM slots up to 1 GB Expansion Slot e One PCI slot IDE e One UltraDMA 133 100 66 33 connector LAN e One VIA VT6103L 10 100 Mbps Fast Ethernet PHY e One VIA VT6107 10 100 Mbps Fast Ethernet controller or one VIA VT6122 Gigabit LAN controller Audio Codec e VIA VT1708B High Definition audio codec DDR2 667 MHz memory modules can be used but the effective speed with be limited to 533 MHz The VT6122 Gigabit LAN controller is a manufacturing option VB7007 User Manual Back Panel I O Ports One VGA port One COM port One parallel port Two RJ 45 LAN ports Four USB 2 0 ports Three audio jacks Line in Line out and MIC in Two PS 2 ports mouse and keyboard Onboard I O Connectors Three COM pin headers with 5V 12V select One digital I O pin header GPI x 4 GPO x 4 Two USB 2 0 pin headers up to four additional ports Two SATA connectors One SMBus pin header One S PDIF out connector One dual channel LVDS panel connector 18 24 bit One LVDS panel power selector 5V 3 3V One LVDS inverter pin header One LVDS inverter power selector 5V 12V One FIR pin header One chassis front panel pin header One front audio pin header
46. tor pulses the extreme values spikes of the pulses create EMI Electromagnetic Interference The Spread Spectrum function reduces the EMI generated by modulating the pulses so that the spikes of the pulses are reduced to flatter curves Settings Disabled 0 20 0 25 0 35 VB7007 User Manual gt Standard CMOS Features gt Frequency Voltage Control gt Advanced BIOS Features gt Advanced Chipset Features Set Supervisor Password gt Integrated Peripherals Set User Password gt Power Management Setu gt PnP PCI Configuration gt PC Health Status Load Optimized Defaults This option is for restoring all the default optimized BIOS settings The default optimized values are set by the mainboard manufacturer to provide a stable system with optimized performance Entering Y and press lt Enter gt to load the default optimized BIOS values Entering N will cancel the load optimized defaults request VB7007 User Manual gt Standard CMOS Features gt Frequency Voltage Control gt Advanced BIOS Features Load Optimized Defaults gt Advanced Chipset Features gt Integrated Peripherals Set User Password gt Power Management Setup Save amp Exit Setup gt PnP PCI Configurations Exit Without Saving gt PC Health Status Change Set Disable Password This option is for setting a password for entering BIOS Setup When a password has been set a password prompt will be displayed whenever BIOS S
47. y make sure the power plug is inserted in the proper orientation and the pins are aligned Then push down the plug firmly into the connector Pin Signal Pin Signal 1 3 3V 11 3 3V 2 3 3V 12 12V 3 GND 13 GND 4 5V 14 Power Supply On 5 GND 15 GND 6 5V 16 GND 7 GND 17 GND 8 Power Good 18 5V 9 5V Standby 19 5V 10 12V 20 5V o J UIST BOOTH VB7007 User Manual The back panel has the following ports PS 2 Mouse Parallel port RJ 45 port f EN j lt Line In J Ai 4 Line Out D a p O mic in VGA port COM port USB 2 0 ports PS 2 Keyboard PS 2 ports mouse and keyboard The green PS 2 port is used to connect a mouse The purple PS 2 port is used to connect a keyboard VGA port The 15 pin VGA port is for connecting to analog displays Serial port COM1 The 9 pin COM port is for pointing devices or other serial devices Parallel port The parallel port is for connecting to LPT devices USB Ports Four standard USB 2 0 ports are provided on the back panel LAN Ports The mainboard provides two Fast Ethernet ports controlled with separate VIA Fast Ethernet controllers One of the controllers can be substituted for a Gigabit LAN controller as a manufacturing option Audio jacks Line in Line out and MIC in Three audio jacks are provided on the back panel
Download Pdf Manuals
Related Search