Stand assy manual
Contents
1. Temporary fixing tape Insert the side bar s screw head into the T shaped foot s screw hole on the top slide downwards then use the hexagonal wrench to partially fasten Insert the M5 x 40 screw into the sleeve then use the hexagonal wrench to partially fasten it to the side bar e Check that the sleeve is not sticking out e Once mounting of the left and right T shaped feet is completed tighten the four screws adjusting so there is no looseness Fasten the screw caps to the screw heads of the left and right T shaped feet A With the screw caps set slightly at an angle place the hooks into the screw holes in the T shaped feet and slide downwards B Press the stoppers of the screw caps into the hollows in the M5 screw heads Hexagonal 4 Screw hole The diagram used for wrench A Hook explanation here is i see through D ial Screw cap et Hexagonal Side bar wrench B Stopper M5 x 40 mm screw ME encased Cable cover S Printer table Side bar Front long Back short SS 3 Attach the stabilizers to the front and back of the T shaped feet AN CAUTION e To prevent toppling be sure to install the stabilizers at each of the 4 locations The toppling of this machine could cause bodily injury or damage the machine Alignment of the screw holes of the T shape feet with2. Mounting D hole WK Hook D z 4 FN RO Locking knobs Front long Back short 5 Store the AC power adapters and cables in the AC power adapter box Connect the main unit and printer before storing the adapters and cables VAN CAUTION e Check that the AC power plug is not connected to a wall power outlet If it is be sure to unplug it The shorter side of the T shaped foot is the back of the stand The diagrams show the procedure from the back side Put the AC power adapters of the main unit and printer in the AC power adapter box e The AC power adapters and the power cords generate heat Be sure to wire them in such a way A WARNING that they keep apart Do not bundle the cables together Doing so could cause them to heat up leading to fire Fasten the cables with the cable clip then insert them in the cable cover Put the cables into the AC adapter box s cable hole The cables enter when pushed in ROMS Peel the backing sheet of the Velcro and attach the Velcro to the bottom of the printer and the printer table Fasten the Velcro on the printer table in a position opposite the position on which the Velcro is attached on the printer Also do not attach the Velcro to a sunken part of the printer or it will not touch the Velcro on the printer table e The Velcro is attached to prevent slipping It is not str
3. those of the stabilizers Slide the stabilizers on the T shaped feet to align with the holes T shape foot to toppling or bodily injury e Do not lift the stand to work on it This may lead A CAUTION Stabilizer Secure the stabilizers on the T shape feet by hexagonal screws using hexagonal wrench Attach the 4 stabilizers on the feet Hexagonal socket screws M5 x 8mm Hexagonal wrench 4 Mount the main unit on the stand A CAUTION e To prevent accidental injury due to the main unit dropping or tipping over the main unit should be held by at least two persons when mounting it on the stand e Check that the stand s hooks are securely inserted into the main unit s mounting holes If not the main unit could drop resulting in injury and damaging the equipment e Make sure the locking knobs are tightened when moving If not the side bar s mounts could be bent or otherwise damaged x The shorter side of the T shaped foot is the back of the stand The diagrams show the procedure from the back side Place the stand s hooks in the mounting holes in the main unit s support pieces and insert securely in the hook grooves Holes are located in three positions The mounted height can be adjusted in three steps of 100 mm 1747 1847 or 1947 mm maximum height according to which set of holes is used Fasten the main unit with the locking knobs left and right The rear frame
4. P L U S Stand AacemDy Nan ial The copyboard is referred to as the set or the main unit below A WARNING Only specially trained technicians should perform installation operations Please be sure to perform the installation and assembly based on this manual Incorrect installation or assembly will be the cause of injury Please have 2 or more persons lift the main unit when installing or removing it For details on installation also refer to the main unit s User s Manual and Assembly and Setup Manual Remove the 4 stabilizers and unlock the caster stoppers before moving the stand To prevent the toppling be sure to remove the stabilizers and unlock the stoppers The toppling of the unit may result in bodily injury or damage to the machine CAUTION e When mounting the printer on the main unit attach the Velcro to prevent the printer from slipping out due to vibrations Remove the printer when moving the main unit If not the printer may fall resulting in damage or injury The Velcro is meant to prevent slipping not to fasten the printer in place Velcro is a registered trademark of Velcro Industries e Diagrams of printers that appear in this manual are representative illustrations The illustration may differ from the actual printer Check the owner s manual of your printer for information about the names of the connectors and their locations and use STAND PACKAGING LIST Please open the carton
5. and check the parts In the rare event that something is missing please contact your store of purchase Name Assembly parts Name Assembly parts T shape legs with casters 2 Screw caps 2 Stabilizers 4 Hexagonal socket screws Locking knobs 2 M5 x 8mm 8 Cable cover Mounted on stand Printer table AC power adapter box 1 set Horizontal bars 1 Mount screws M5 x 20 mm 2 mounted on side bar temporarily fastened on side bar Velcro 2 sets Mount screws M5 x 40 mm 2 Hexagonal wrench Sleeves 2 width across flats 3 mm 1 ASSEMBLY OF THE STAND Preparation Mount the pen tray on the main unit For the mounting instruction please refer to the Assembly and Setup Manual 1 Lock the caster stoppers Press the bottom portion of the stoppers down to lock them N CAUTION e Lock the casters of the T shaped feet left and right If not the stand could Caster slip causing the stand or main unit to fall and resulting in injury or damage 2 Mount the T shaped feet to the side bar The shorter side of the T shaped foot is the back of the stand The diagrams show the procedure from the back side Set the T shaped foot with the cable cover on the right side the printer table side Remove the temporary fixing tape from the ends of the side bar Side bar PEARED IEPEN F Temporary fixing Space of about 2 mm tape M5 screw mounted on side bar gt
6. ong enough to prevent falling Remove the AN CAUTION printer when moving the stand If not the printer could be damaged or fall on your feet etc causing injury Place the printer on the printer table e Place any extra cable length in the AC power adapter box so that no cable is hanging out This completes mounting of the main unit on the stand Make a test print Cable clip AC power adapter box Cable cover Main unit s AC power adapter Printer s AC power adapter Using the cable clip Cable hole Fasten the cables with the cable clip ZB 26 4626 11D
Download Pdf Manuals
Related Search