eurösec CPX control Panel
Contents
1. 1 With the display showing 01 JAN 18 58 01 2 Enter a Master Code the display will show Do you wantto SET the System 3 Press NO five times the display will show Do you want to Prog USER CODES 4 Press YES the display will show Enter User No 1 15 Then YES 5 Enter the user number 1 to 15 that you wish to program followed by YES the Now Enter Code display will show eee Then YES Page 12 eur sec CPX User Manual Note 10 11 Enter the code you require codes may be 4 5 or 6 digits followed by YES Entering 000000 will delete an existing code If the code already exists an error will be shown choose another code and return to step 6 The display will show Code Type not if user 1 is being programmed Master ok Press NO until the require level of code is shown Refer to page 3 for code level details Refer to Advanced Code Programming for details for User level of Control Press YES The display will show for example Be Code Groups are only used in conjunction with controlling outputs See Advanced Code Programming section for details Press YES The display will show VoComm Trigger This determines if using this user code to Set or On Ok Unset the system will trigger the Vo Comm For more details on Vo Comm please refer to the Vo Comm section Press NO2. At this point the system will revert to battery back up The battery will only have a limited time that it can sustain the system for Note Your installation company will have determined what size battery is required to comply with legislation It is important that your security system is serviced on a regular basis on order that it continues to comply with the legislation Servicing may also be a requirement of you insurance policy In the event of a sustained power cut the system battery will continue to supply the system until the battery voltage falls to a set point at this stage the display will show Fuse Bat FAULT I Check A fault sounder will start enter a valid User Code to stop the fault sounder At this point it is essential that you contact your installation company Setting the system with Mains Fail In the event of a short term power cut where it is known when power will be restored e g Engineers working on power lines that affect your premises it might be necessary to set this system Please follow the steps outlined below 1 With the display showing I EnterCode III Check J Note In the event of a mains power failure the control panel will display that a fault has occurred if the pre programmed time has been exceeded Power Cut FAULT 01 JAN 18 58 01 2 Enter your User code The display will show A z Power Cut FAULT 3 yo
3. aur sas G Control Pane User Instructions eur sec CPX Contents User Information Introduction es RER RM UNI eus a User Code Types Setting The System Setting amp Unsetting via Keyswitch u en Unsetting The System uusneerssensnensnnnnennnnnennnen nenn Part Setting The System REMOVING Zones Testing The System Viewing The Event Log Changing The Chime Status Programming User Codes u 222ursaun nennen Programming Time amp Date eerren Vo Comm Introduction Vo Comm Programming Using Vo Comm nn Messages from Vo Comm urssesnensnensnennsnnenneen nenn User Initiating Remote Access Resetting After An Alarm unssnenersnnnersennnennnnnnn nn nennen Setting Engineer Authorisation G Tag Introduction Programming G Tag 242444r2snn nen nnnnnennnnnnnen nenn Vsing G Tag rare Display Status Blanking r 20erssnn nennen Keypad Tamper 44 s22 862 a earar OaE Mar AA a SSi Key Pad Aloftina anar in ne nr System Tampers nn Mains Failure Setting The System With Mains Fail Re setting The Display After A Mains Fail Advanced Code Programming Using Advanced Code
4. Your installation company will give training on the use of the equipment in order to comply with the relevant standards and will be able to answer specific questions about your system request for additional or new staff training should be directed to your installation company IMPORTANT USER INFORMATION If the Control Panel is non EN then all displays will be shown and ENTER CODE CHECK will not be displayed All information displays will remain until cleared by the User User Code Types Five Levels of User Codes are available on the eur sec CPX each user code type allows for different levels of access In total 15 User codes may be programmed by a Master Level User Code User number 1 will always be a Master Level User but the remaining 14 User Codes may be programmed by a Master Code to the required level of access These may be changed at any time via a Master level code The User Code levels available and the functions available for the levels are Master Allows Setting Unsetting Zone Remove if programmed by User 1 will always engineer Test System View Log Chime On Off User be Master Level Codes Set Time Date Reset After Alarm if programmed by engineer Unsetting Control Allows an output that has been pre programmed by the installation company to be operated May have the attribute of Can Cant Unset May never Set a system Refer to Advanced Code Programming for details Set Only Only Allows for
5. Introduction G Tag is a method of Setting and Unsetting your security system via a Proximity Reader and a Tag The Proximity Reader may be an internal reader that is fitted on to the inside of a doorframe etc or an external reader that is fitted into the doorframe on the outside of the premises Legislation contained within DD243 does not allow for the transmission of confirmed alarm signals once the entry time has started if the user of the security system is using a manual code entered into the keypad G Tag conforms fully with the requirements of this legislation relating to confirmed alarms on G Tag Fob entry Because the G Tag uses Proximity Technology there are no batteries to change in the unit it is small enough to be carried on the users key ring and one Tag may be used on multiple security systems and some door entry systems Programming G Tag Tags Onto Your System Programming The Tags onto your system is very simple Follow the instructions for programming User Codes onto your system up to the point when you would enter the User Code At this point present you Tag to the Proximity Reader and a code will be entered for you Continue with the instructions entering the User Name etc Each G Tag will be identified on an individual basis when it is used to Set or Unset the system Using G Tag On Your System G Tag is a method of entering a code into your security system To Set Your System Using G Tag When you wish to Se
6. N 5 Enter the zone number you wish to remove followed by YES pressing NO will un remove a zone The enter Zona i me display will show then YES or NO 6 Repeat step 5 until you have removed all the required zones nl Do you want to 7 Press 0 to escape the display will show SET the System 2 8 Press YES the continuous exit tone will sound 9 Exit the premises via the authorised exit route the exit tone will change as detectors are violated When the premises are secure listen that the exit tone returns to the continuous tone Wait until the exit tone finishes before leaving Note Zone remove is only effective for the one set Page 7 User Manual eur sec CPX Testing The System Master amp Main codes only 1 With the display showing 01 JAN 18 58 01 2 Enter a Master or Main level code the display will show Do you wantto SET the System 3 Press NO the display will show Do you wantto REMOVE Zones 4 Press NO the display will show Do you want to TEST the System 5 Press YES to test the system r 1 Status 4 Strobe 6 The display will show F Sounder 9 Bell 7 lt All Zones ok gt 7 Then for example emee 8 Pressing 1 will enter zone Status mode All zones will show on the display and will be deleted
7. Reporting Off Make an Alarm Test Call Do you wantto Set Up VoComm 01 Jan 00 00 01 eur sec CPX User Manual Using Vo Comm if fitted Once Vo Comm has been programmed see previous page the Vo Comm will operate in one of two ways 1 Alarms Only The Vo Comm will only communicate when an alarm occurs on a Closed Set system This mode is active when the Open Close option is Off 2 Alarms amp Status The Vo Comm will communicate when an alarm occurs or when the system is Closed or Opened Set or Unset Receiving a Call From Vo Comm When Vo Comm calls you it will start to pass its message as soon as you pick up the telephone At the end of the message you will hear a single tone at this point press a numeric key on your telephone keypad twice A rising tone will be heard that indicates that the call has been acknowledged If you do not acknowledge the call or hear the rising tone the Vo Comm will repeat the message several times and then go on to dial the remaining telephone numbers until the call is acknowledged Messages From Vo Comm Two types of message will be sent by Vo Comm Either a status message or an alarm message Typical Status Message Site 05 Close User OT This would indicate Site ID 05 was Closed by User 1 The term Closed Set The term Open Unset Note In order for the Vo Comm to report Openings and
8. than 1 event is present the display will f Zone 005 TAMPER show io 01 JAN 18 58 01 gt The right arrow is now indicating that more events are available for viewing Page 21 User Manual 8 Press the YES key to view the next event and carry on to view any others if present When viewing the last event the display will show for example eur sec CPX Zone 005 TAMPER 01 JAN 18 58 01 lt The left arrow now indicates that you are atthe end of events The NO key may be used to scroll back the opposite way Re setting the system 1 2 3 4 5 6 If the system is programmed for Any code reset enter a User code The display will show Note If NO is NOT pressed then the alarm status will only be displayed for ten seconds The display will then show Enter your user code again The display will show Press the Reset key Or Press YES The exit tone will sound and the display will show for example lt lt lt lt ALARM gt gt gt gt Press NO to view I Enter Code II IT Check Do you want to SET the System EXIT All Zones ON f Enter the code again to abort the setting Time will count down The system is now reset Or If a higher level of code is required one of the following displays will be shown Use a Master code to reset the system Or Call the in
9. until the setting you require is displayed YES or NO The Vo Comm will need to be programmed in order for this option to work please refer to the Vo Comm section in this manual Press YES The display will show Er Name If you wish to accept the name shown press YES and jump to step 13 Or If you wish to change the name shown press ser 2 Name NO the display will show You may now enter up to nine characters for the user name using the layout shown on the following page for the allocation of characters Page 13 User Manual ee eee ee CD Q QD ABC DEF GH I 4 GG D JKL PQR I I lt gt Co i STU VWX YZ I I AO CO GES i 0 9 Ge ER EE PR SoS i EP En en A J 12 Referring to the character map enter the required 13 14 15 character pressing the 3 key will display G pressing it again will show H and again will show I Once the correct character is displayed press YES and the display will move on to the next position Continue entering characters up to 9 If you require a blank space press YES while the is displayed As you press YES for the ninth character eur sec CPX or if you have jumped from step 9 the display will change to Do you want to Prog USER CODES If you wish to program other User Codes return to step 4 Or Press 0 to return to 0
10. 1 JAN 18 58 01 Page 14 eur sec CPX Programming Time amp Date 1 10 11 With the display showing Enter a Master Code the display will show Press NO six times the display will show Press YES the display will show Press YES the display will show Press YES to accept and the go to step 8 OR Press NO display will show Enter the Year then press YES Display will show Press YES Display will show Enter the Day Month ie 0706 for 7th June followed by YES The display will show Enter the time using 24Hr Clock ie 23 30 for 11 30pm followed by YES the display will show Press 0 the display will show Page 15 User Manual 01 JAN 18 58 01 Do you want to SET the System Do you want to Set DATE TIME Summer Adjust is On ok Year is 2005 ok Enter Year 20 Then YES Year is 2005 ok Enter Day Month Then YES Enter Hrs Mins Then YES Do you want to Set DATE TIME 07 Jun 23 23 02 User Manual eur sec CPX Vo Comm if fitted Vo Comm is a method of transmitting signals to a standard land line or mobile telephone giving information regarding the status of your security system This may be in addition to or instead of
11. Closings the Open Reporting for that user must be programmed to On within the Programming User Codes section Typical Alarm Message Site 05 Alarm Zone 06 This would indicate an alarm at Site ID 5 has occurred on Zone 6 Page 19 User Manual eur sec CPX User Initiating Remote Access Optional Access Remote allows your installation company to examine your system and re program system settings as you need the changes without the need for an engineer to visit your premises If your system has remote communications fitted your installation company may have programmed the system so that you initialise the Access Remote call usually on lines with incoming calls barred To initiate the Remote Call follow the instructions below 1 Negotiate with your installation company when you should initiate the Remote Call 2 With the display showing 01 JAN 18 58 01 3 Enter a Master Code the display will show Do you want to SET the System 4 Press NO seven times the display will show Do you want to Access Remote 5 Press YES the display will show PISAS WAIT until dialling commences then Please WAIT Dialling until connection then Please WAIT Connect 6 When your installation company has finished the display will show 01 JAN 18 58 01 Note In the event of any errors the display will show IIIIERR
12. EXIT Followed by YES if a Master or Main type code All Zones ON 1 has been used Time will count down Enter the code again to abort the setting or press the Reset key The display will show 01 JAN 18 58 01 The system is now reset Page 29 User Manual eur sec CPX Advanced Code Programming This section cover the programming and use of Advanced Codes The Code Level of Control is classed as an Advanced Code Several parameters will need to be programmed by the installation company before a Control Code may be programmed into the system You should also note that a Code Level of Control may never Set the system Typically a Control Code would be used for turning on an output or act as a limited door access system In order for this to function additional hardware would be required To program a Control Code level Follow the normal instructions for programming codes At the Point when you are asked for the Level choose Control When asked for the Code Group enter 1 to 8 your installation company will have given you what group to use Then choose Can or Cant Unset dependant on your requirements Follow the normal instructions to the end for programming codes Using Advanced Codes Two typical uses for Advanced Codes are 1 To turn on an output e g a light Enter the User Code or present your Tag the output will turn On Enter the User Code or present your Tag again the out
13. OR III Check line is not in use or disconnected etc lt Try Again Page 20 eur sec CPX User Manual Resetting After an Alarm Fault and Alarm Displays Your installation company will have programmed the reset modes for your system so that it complies to your insurance company and legislation requirements Your installation company will have informed you as to the type of reset that your system is set for Before attempting to reset your system ensure that the system is Un set 1 In the event of a fault or an alarm occurring the m internal sounder will sound along with the external te bells for a full alarm The display will show if the system is unset If the system is set enter your code to unset it 2 Press the NO key to view the cause of the Alarm or lt lt lt lt ALARM gt gt gt gt Fault Press NO to view Note If NO is NOT pressed then the alarm status will only be displayed for ten seconds 3 The display will then show 11 Enter Code Enter your user code again 111 Check 4 The display will show Do you want to SET the System 5 Press 0 The display will show lt lt lt lt ALARM gt gt gt gt Press NO to view 6 Press the NO key to view the cause of the alarm or Zone 005 TAMPER fault The display will show for example 01 JAN 18 58 01 7 If more
14. Programmed 14 To enter or change the number repeat from step 7 Site ID 15 Display will show 00 16 Press NO twice Display will show Site ID 17 Enter a unique Site ID for the premises 00 to 99 followed by YES This Site ID will identify what system is calling you Open Reporting On 18 Display will show To change this press NO until the required setting On or Off is displayed then press YES The term Open relates to the system being Unset With Open Reporting turned On the Vo Comm will report the system being opened Unset for all users who have had the attribute of Vo Comm Trigger On allocated in the User Code Programming Page 17 User Manual 19 20 21 22 The display will show The term Close relates to the system being Set With Close Reporting set to anything other then Off the Vo Comm will report the system being closed Set for all users who have had the attribute of Vo Comm Trigger On allocated in the User Code Programming Options available are Off No system Close are reported Full Set Only Full Sets are reported Any Set All Sets Full amp Part are reported Press NO until your required setting is shown then press YES Display will show Press NO this is dealt with in the using Vo Comm section The display will show Press 0 to return to Page 18 eur sec CPX Close
15. an t Set Check If the fault clears within 20 seconds then the exit will begin otherwise the display will return to Day Unset Mode Setting amp Unsetting the System via a Keyswitch if fitted One of two types of keyswitch es may have been fitted to your system Normal To set the system with a normal keyswitch insert the key and turn to the ON position then remove the key Follow the instructions from step 3 above To unset insert the key and turn to the OFF position Biased To set the system with a biased keyswitch insert the key and turn it then return the key to the original position and remove Follow the instructions from step 3 above To unset repeat this operation Page 4 eur sec CPX User Manual Unsetting The System 1 Enter the premises via the authorised entry route the broken entry tone will sound proceed to the keypad 2 At the keypad enter a valid code the display will show 01 JAN 18 58 01 3 The system is now unset Note G Tag Proximity Tags may be used for setting and unsetting the system Please refer to the Using G Tag section for instructions Part Setting The System using Master amp Main type codes 1 With the display showing 01 JAN 18 58 01 2 Enter a Master or Main type code the Dovoirwantito display will show for example ns 3 Press 1 2 or 3 for Part 1 2 or 3 the EXIT displ
16. as each zone is triggered Press 0 to escape Pressing 6 will silence the internal sounder Pressing 4 will toggle the Strobe On Off Pressing 9 will toggle the Bell On Off Page 8 eur sec CPX User Manual 9 Whilst in Test mode any zones violated will sound the internal sounder if it has not been silenced and show on the display 10 When you have finished testing the system press 0 twice the display will show 01 JAN 18 58 01 Viewing The Event Log Master code only 1 With the display showing pey 9 01 JAN 18 58 01 2 Enter a Master Code the display Doyouwantto will show for example SET the System 3 Press NO three times the display Do you want to will show View the LOG 5 f Read Log 4 Press YES the display will show for example 01 JAN 18 58 01 Page 9 User Manual eur sec CPX 5 This is the most recent event in the log Whilst viewing the Log Pressing NO will move back to the previous event Pressing YES will move forward to the next event Pressing 7 will take you to back to the last event of the previous day Pressing 9 will take you forward to the first event of the next day 6 When you have finished viewing the Log press 0 twice The display will show 01 JAN 18 58 01 Changing The Chime Status Master code only The Chime zones will have previously been programmed by the ins
17. ay will show for example Part 1 15 2 i i wn Note Your installation company will have Timewill count do informed you what zones are being removed omitted for the Part Set you are using Refer to the System Attributes section for what zones have been programmed as Part Set zones Page 5 User Manual eur sec CPX 4 5 6 The exit tone may or may not be heard depending on the system settings programmed by the installation company Exit the premises or retire to an unprotected part of the system At the end of the exit time either the exit sounder will stop if the exit tone has been audible or a single beep will be emitted if the exit tone has been silent The system is now Part Set you are free to move around the zones that have been removed by the Part Set but other zones on the system are active Page 6 eur sec CPX User Manual Removing Zones When Setting Master amp Main codes only If programmed by the installation company individual zones may be removed omitted when the system is set this may only be done by a Master or Main level of code 1 With the display showing 01 JAN 18 58 01 2 Enter a Master or Main level code Do you want to the display will show SET the System D tto 3 Press NO the display will show BELGE Danke 2 f Enter Zone 4 Press YES the display will show hena Yos or
18. central station communications It should be noted that Vo Comm should not under any circumstances be used to ring the Emergency Services directly It will not be possible to program 999 911 or 112 as the telephone numbers that the Vo Comm will dial Before Vo Comm can work several options will need to be programmed Please read below for information Vo Comm Programming if fitted 1 With the display showing 01 Jan 00 00 01 2 Enter a valid Master Level Code 5678 default Display will show Do you want to Set the System 3 Press NO 7 times Do you want to Display will show Set Up VoComm 4 Press YES Display will show VoComm i Off 5 Press NO until display will shows re gt On 6 Press YES Display will show VoComm Tel No 1 Is Un Programmed Or for example VoComm Tel No 1 12345678910 7 To enter or change this number Press NO Display will show VoComm Tel No 1 Page 16 eur sec CPX User Manual 8 Enter the telephone number you require followed by YES 9 Display will show VoComm Tel No 2 is Un Programmed 10 To enter or change the number repeat from step 7 11 Display will show VoComm Tel No 3 is Un Programmed 12 To enter or change the number repeat from step 7 13 Display will show VoComm Tel No 4 is Un
19. lidated Keypad Alert If programmed by your installation company the two PA keys or keys 1 amp 3 if programmed by the engineer when pressed together will act as alert keys The exact function will depend on what they have been programmed for But for example if they are programmed as panic pressing them will activate the alarm when the system is set or unset Keypad Tamper The keypad will monitor the number keys that are pressed without a valid User Code being entered More than 24 key presses will cause a keypad tamper This will be displayed as Keypad x Tamper and will require a valid User Code entry to stop the sounders If the system was Unset only the internal sounders will operate If the system was Set a full alarm will be generated System Tampers The full security system is tampered any attempt to remove covers from Keypads Control Panel Keypads Bell Box es or detectors will cause a tamper alarm This also applies to cut cables If the system is Unset when the Tamper occurs the alarm will be internal sounders only If the system is Set a full alarm will be generated The alarm may be silenced by entering a valid User Code The system may only be Reset when the Tamper has been cleared otherwise another Tamper alarm will be generated Page 27 User Manual eur sec CPX Mains Failure I Enter Code In the event of a Mains Power Failure the display will show NI Check 1111
20. o user authorisation will be required to grant engineer access to the alarm system 4 Press YES The display will show Se oe This option is dealt with later s i 5 Press YES The display will show Do you want to Authorise Engnr 6 Press 0 to return to 01 JAN 18 58 01 Using Engineer Authorisation A valid Authorisor code will be required to give an engineer access to the alarm system This may be done in two ways 1 The engineer will enter his her code The display Enter Authorisor will show Code 2 Enter a valid level of User code to grant the engineer access Page 24 eur sec CPX User Manual Or i i ig Do you want to 1 Enter a Master User code The display will show SET the System 2 Press NO until the display shows Do you want to Authorise Engnr 3 Press YES The display will show for example a Authorisor 2 i Engineer Access 4 Press YES The display will show is Off Ok Sr Engineer Access 5 Press NO The display will show is ON Ok i i ar Do you wantto 6 Press YES The display will show A th rise Engnr 7 Press 0 to return to AN aD Provided that the next code entered is a valid engineer code access will be granted to him her without further user intervention Page 25 User Manual eur sec CPX G Tag
21. put will turn Off 2 To open a door e g door access with limited function Enter the User Code or present Tag to external Tag reader door will release for the time period determined by your installation company Page 30 eur sec CPX User Manual System Attributes SJ SE cc Control Panel Zones Zone No Zone Type Descriptors Part Info Example 182 Radio Zones If Fitted Zone No Zone Type Descriptors Part Info Page 31 User Manual eur sec CPX Service Record Date Comments Signature Alarm Reset Type Tamper Reset Type Service Company Service Notes Page 32 eur sec CPX User Manual User Chart Please use this chart to indicate what user names have been programmed onto your system and those that are in use In Usel Code G Tag User Name User 1 User 2 User 3 User 4 User 5 User 6 User 7 User 8 User 9 User 10 User 11 User 12 User 13 User 14 User 15 Note Under no circumstances should you write down the actual code Radio Fob Users If Used User Name User 81 User 82 User 83 User 84 User 85 User 86 User 87 User 88 Use this space to record any codes that have been reserved for Keyswitch es Page 33 Risco Group UK Ltd Commerce House Whitbrook Way Stakehill Distribution Park Middleton Manchester M24 2SS United Kingdom Internet www riscogroup com e mail sales riscogroup co uk Risco Group UK Ltd reserve the right to amend the software and features witho
22. s 224222044n0ennnnn nennen nn System Attributes Service Record nenn User Chart ihn User Manual Na af FB WwW PD 1 Oo oo 1 oO 10 11 12 14 15 16 16 18 19 19 20 21 22 24 26 26 26 27 27 27 27 28 28 29 30 30 31 32 33 User Manual eur sec CPX User Information Customer Name Customer Address Control Panel Model eur sec CPX No of Keypads pad 1 Location pad 2 Location pad 3 Location pad 4 Location G Tag 1 Location G Tag 2 Location Keyswitch Location if fitted Reserved User Code User No Installation Company Name Installation Company Address Installation Compan Other Information Note This section to completed by the installation engineer Page 2 eur sec CPX User Manual Introduction The eur sec CPX control Panel is a microprocessor based unit with multiple user and engineer programmable options Control of the system is via LCD Remote Keypad RKP giving two rows of 16 character English text Facility is provided model dependant for Central Station and or Vo Comm message communication to inform of system status and alarm events Vo Comm messages may be sent to standard land line telephones or mobile telephones Please take time to familiarise yourself with the type of equipment fitted to your premises as it will prove invaluable whilst using this manual
23. stallation company Or Call the central station or installation company as instructed and quote the number given Or Page 22 Can t Set Use Master Code Can t Set Use ENGNR Code Can t Set Use ENG Anti Code 1234 Can t Set Use Anti Code 1234 eur sec CPX User Manual 7 To reset the system with an Anti Code contact the central station or engineer as instructed by the installation company and quote the number given by the display 8 The central station or engineer will give a return Anti Code this may contain the YES amp NO keys for example 5 YES 2 4 9 Enter this Anti Code into the keypad 10 The system is now reset Page 23 User Manual eur sec CPX Setting Engineer Authorisation A User Code may be required to authorise an engineer to gain access to the system in the event of service or maintenance schedules The level of User Code required to authorise the engineer to access the system is set within the User Menu that is accessed via a Master Level Code Setting the Engineer Authorisation Level Do you want to 1 Enter a Master User Code The display will SET the System show 2 Press NO until the display shows en Then press YES Engnr Authorisor 3 Press NO until the required setting is displayed any Master Main and Any are user code levels If None is selected n
24. t your system simply present your Tag to the Proximity Reader and exit the protected area following the normal Setting You System Instructions To Part 1 Set Your System Using G Tag If using G Tag Part 2 and Part 3 Setting will not be available a manual code should be used to Part 2 or 3 Set the system To Part 1 Set your security system press YES twice Press CODE to Part Set the display will show Present your Tag to the Proximity Reader and exit the protected area following the normal Part Setting You System Instructions Page 26 eur sec CPX User Manual Display Status Blanking It may be a requirement that the Status Set or Unset display of the security system is not displayed If this option has been invoked by your installation company the Set or Unset Status will only be displayed for ten seconds when the system is Set or Unset The top line of the display will then be blanked off You may check the Status of the system at any time by pressing the YES key and then entering a valid User Code If the system was Set when you did this the display will ask if you wish Unset the system To do so press YES within ten seconds If the system was Unset when you did this the display will ask if you wish Set the system To do so press YES within ten seconds If you do not choose to Set or Unset the system within the ten seconds the top line of the display will be blanked out and the code entry will be inva
25. tallation company A Master level code may change the status of the Chime between On and Off To do so proceed as follows 1 With the display showing ia Se 2 Enter a Master Code the display will Do you want to show for example SET the System 3 Press NO four times the display will show Do you want to Change Chime Page 10 eur sec CPX User Manual 4 Press YES the display will show for example Chime is Off ok Or Chime is On ok 5 Press NO to change the status of the Chime gt i i ER o you want to then press YES the display will show Change Chime 6 Press 0 to escape the display will show 01 JAN 18 58 01 Page 11 User Manual eur sec CPX Programming User Codes Master code only The charts on pages 2 amp 33 should be completed by the engineer user for future reference of what codes have been allocated on your system Under no circumstances should the actual user code be written down If your installation company has given you keyswitches for the operation of your system some user codes may have been reserved for use by these keyswitches If your engineer has indicated see pages 2 amp 33 that some of the user numbers on your system have been reserved you should not use them whilst programming user codes If you do so your system may be adversely affected
26. the setting of the system Main User Allows Setting Part Setting Zone Remove if programmed by engineer System Test Unsetting Reset after Alarm if programmed by engineer User Allows Setting Part Setting Reset after Alarm if programmed by engineer Unsetting Page 3 User Manual eur sec CPX Setting The System 1 With the displ howing e display showing 01 JAN 18 58 01 2 Enter your User code Followed by YES if a Master or Main type code has been used The display will show Fa Now 3 All Zones ON 15 and a continuous exit tone will sound Note Count down in display is dependant on the setting mode Time will count down programmed by the Engineer 3 Exit the premises via the authorised exit route the exit tone will change if any detectors are violated during exit 4 Once the premises are secure listen from outside the protected area that the exit tone returns to the continuous tone 5 Wait until the exit tone finishes before leaving Note If enabled by the engineer pressing the Quick key during exit time will shorten exit time to 3 seconds Note G Tag Proximity Tags may be used for setting and unsetting the system Please refer to the Using G Tag section for instructions Pre Exit Check At the start of the setting procedure any non exit routes that are open will show a fault tone The display will show for example Zone 8 12hr C
27. ur User code again The display will then Can t Set Check snow Followed by YES if a Master or Main type code has been used EXIT 4 Then press YES The display will show All Zon s ON j Note The display will switch between the EXIT display and the Power Cut FAULT display as the time counts down Time will count down Page 28 eur sec CPX User Manual 5 6 Exit the premises via the authorised exit route Once the premises are secure listen from outside the protected area and wait until the exit tone finishes before leaving Re setting the display after a Mains Fail Note In the event of a Mains Power Failure the control panel will display that a fault has occurred ifthe pre programmed time has been exceeded In the event of a mains power failure the display I EnterCode will show III Check Enter your User code The display will show Power Cut FAULT 01 JAN 18 58 01 gt The right arrow is now indicating that more events are available for viewing Press the YES key to view the next event and carry on to view any others When viewing the last event the display will show for example Mains Ok Ack 01 JAN 18 58 01 lt The left arrow now indicates that you are at the end of events The NO key may be used to scroll back the opposite way Enter your User code again The display will then show
28. ut prior notice Q I BSIA THE BRITISH SECURITY as TRY ASSOCIATION INVESTOR IN PEOPLE Y u a Certificate No 935289 PR5598 Rev1 3 5INEW021UM C
Download Pdf Manuals
Related Search