User Manual & Spare parts catalogue for the TP 250
Contents
1. User Manual amp Spare parts catalogue for the TP 250 PTO K wood chipper in the park series UTP 250 PTOK TE 250 MOBILE URNTABLES Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com 1 Introduction Congratulations on your new TP wood chipper Linddana produces TP wood chippers of the finest quality by using the most modern production technologies i a laser cutting CNC technology and robot technology in bright and open production facilities For safety reasons and in order to get maximum pleasure from the wood cutter it is important to read these instructions before use The user manual explains about safety use and maintenance so that the work with the wood chipper will be safe and profitable This manual has been translated from Danish Linddana A S J rgen Due Jensen Managing director Your distributor is always available with spare parts advice and guidance Distributor stamp Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 2 EU declaration of conformity Manufacturer LINDDANA A S lholm Bygade 70 lholm 7160 T rring Denmark hereby declares that Wood chipper is in concordance with the provisions of the Machine Directive Directive 06 42 EC and with the national legislation which translates this directive2. 1000 ENTER e The low rpm of the rotor where the retraction of the rollers stops RPM Stop 850 ENTER Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 36 e Number of pulses the rollers reverses when they are stopped because of low rpm of the rotor On the TP 250 the rollers do not reverse value 0 Pulses Reversing 15 ENTER e Minimum temperature for starting the retraction of the rollers Temp Oil Heating 20 C ENTER 12 3 Setting roller speed Regulation by adjusting the flow valve see fig 12 The speed of the rollers must be set according to the current position of the knives cf the table below p Rotor 10mm 12 mm 13 mm 15 mm Rpm ETP250PTOK 1000 pp Alternatively the current roller speed can be seen directly in the display on the PILOT K After setting the position of the knives on the PILOT K the following is done Push x and a at the same time and the following display will be shown VO states the calculated roller speed Ro O 0 0 1000 VO 28 VI O V2 0 V1 V2 states the current roller rom Notice that the rotor rom must be over RPM Start or the rollers will not turn A roller alarm is tied to this display The roller alarm is activated if V1 or V2 is greater than VO This can be used for setting the roller rom The roller alarm will so
3. is in concordance with the following other EC Directives 2000 14 EC Furthermore it is stated that EN 13525 harmonised standard has been used Title Managing director Name J rgen Due Jensen lholm 02 November 2015 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 3 Table of content 1 MCFEOUUCEIO N iv dio antik atan bou se sea kaka en a kaa ole ae n aa laa aie kak aa me laa ban aa dan bagas saten 2 2 EU declaration of CONTOTMITV kis ai k k koi ko ne es avek epe spes e ansan k s eee sense enes esse sees enes 3 3 Table OM CONTENE ywit aki assi a a via m ka ak ank ok a a ak kk a a l a a e ai a a A e pise ke 4 4 NISC yi stan ki ka a a in a kk ii a a kk a e kk satan e a a ka RE n l ata a a a 5 5 Mounting INSTEUCTION S s kra lw ek wk ek kr meb kk kf a e l n r l ar a e 6 5 1 BET ON W S tay ket filo ladan lan Pie do oto a an Ri op e a a taka a SEE e aa ta du 6 5 2 NM IOU FUN E NASEFU T ON fb kose a na E e e l a e pa e a aan a A e Es es 8 6 SATETYIASTTUCUONS scree vii ai ie sit ka a im an Ge k ak RON ao ae ea koke 9 6 1 SITE KES UL AT OASE iya in ot N e e E a a ei ka N A E TA EAA eres ESS 9 6 2 PICTOP 87 ag S USE A ep ya taa fk kol kk kl ka a kt a w oe e en ka a e a a nt a n a e ko a amp ka ae RER 11 6 3 NOISE OV Cleese it ia Sao ik it a a a a a aa ae a re ae es ne ae ont ine ae pe e 13 6 4 Env
4. Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 25 8 5 Grinding of knives It is very important for the quality of chips that the knives are sharp They have to be checked at least once a day The grinding interval of the knives can be prolonged by grinding them with a carborundum stone regularly The grinding can be done as wet grinding with a bond stone see fig 20 Never use an angle grinder or a similar tool for grinding the knives AE Figure 20 Wet grinder When grinding knives you have to pay attention to the width of the knife set The width has to be the same because of the balancing of the rotor Therefore the knives always have to be ground in sets The knives must have a measurement of min 90 mm See fig 21 After that they must be thrown away The edge of the knives must be ground at an angle of 28 See fig 21 3 o L L Figure 21 Grinding angle and minimum knife width for chipping knives Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 OCopyright 2008 26 9 Special instruction for TP 250 MOBILE TURNTABLE The TP 250 MOBILE TURNTABLE is a trailer mounted wood chipper comprised of a trailer upon which a wood chipper with own engine is mounted The trailer can be coupled to a vehicle with a ball and sock
5. a crane or any other hoisting device ground assistance see Fig 3 The machine can also be lifted with a fork lift truck This is done by using the holes made for this purpose on both sides of the foot see fig 4 Make sure that the forks of the truck are put all the way through otherwise the machine can tip over The TP 250 MOBILE TURNTABLE is mainly transported on the trailer wheels but it can also be lifted with a fork lift truck under the trailer bearers see fig 5 Lifting point Figure 3 Lifting point on the machine Figure 4 Lifting with a fork lift truck Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 Figure 5 Lifting with a fork lift truck Store the manuals for the PTO member with this manual in the manual box on the machine Before operation you must check that the wood chipper cleared of foreign bodies The machine must be uncoupled from the tractor s PTO and for the MOBILE models the key must be removed from the ignition before opening for the rotor Check that the rotor is at a complete standstill Turn the ejector tube so that it faces the opposite direction of the rotor housing see fig 6 Loosen the bolts that hold the upper and lower rotor housing together Lift the top part of the rotor housing up until the ejector tube rests on its own Turn the rotor a few times by hand Remove any
6. chipper During operation no one except the driver of the tractor is allowed in this area e If people should come inside the security zone by accident the emergency stop which stops all movement by the crane and feeding into the wood chipper must be pressed immediately The emergency stop should always be activated when the driver leaves the driver s cab e AT DANGER AKTIVATE THE EMERGENCY STOP IN THE TRACTOR Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 11 6 2 Pictograms used TP 250 PTO Lifting point for fork lift truck Hearing protector and eye Lifting point for crane protection prescribed Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 12 TP 250 PTO K 20m Warning Objects thrown Warning Rotating knives Warning Must not be hand fed Safety distance 20m Wait for rotor to stop MAX 1000 RPM Lifting point for fork lift truck Lifting point for crane oo O Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 13 6 3 Noise level The sound effect level and the sound pressure level from
7. n e a e aka sin a a 35 12 gt Sene TONG TSC CC eae at cece hart eat E een ct rane sone G 36 124 Alane Eli ka n a kat a kn e a n a ca n n pd pt ka kk ek ao ni ke ess kase das 37 125 COMME A S eee ae ao kn born ia is eee tk n ea ka Ron e ei ae a RE Bra in rose Rou Na e ee DR 37 42 6 MSC PNG II AA vil kat n ces kk a ni a ka cc kk snap ee kn a kk ko ee wee a ai rak 37 127 Electrica MOUN CAP ei rt ta a ka an anl kt a kr a ca n a a e SENSE Te n ka Ra ae nek 38 128 Append US r QISPIAY sais sava os oil de kanape a e ok n a a a a a a a a an e a a van aa 39 13 Troubleshooting for wood chipper TP 250 ccsccscecsscscsscscsccsceccscsseccecs 42 14 Guarantee obligation for wood chipper ccccsccccsccccscsccccsceccscecsscsseccece 43 15 Technical data wood chipper ccccsccsccccsceccscsccccsccccsceccscsccccscescscssscece 45 16 JACCESSOFNOS 455040 oeil te E ee kara ba ke ka e ekate ab G 47 17 Spare parts CatalOBUE 14449 pipe aaa nee kasab s b kb one N 47 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 OCopyright 2008 4 Use The TP 250 wood chipper is designed for stationary wood chipping in the form of braches etc The machine must not be used for materials containing stone metal or other foreign bodies These foreign bodies can in the best case dull the knives and in the worst case break the machine Knives and anvil c
8. 35 44 56 TP250 MOBILE TURNTABLE 900 16 24 31 39 51 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 16 8 Maintenance During all maintenance and repairs the machine and the drive must be shut off Tractor mounted machines have to be placed on an even surface and be uncoupled from the tractor s PTO 8 1 Maintenance schedule disc cleaning lubrication Le en e me re Changing of return filter for hydraulic X ae K Na e n a n pan IE a on men X Change hydraulic oil Anvil turn change Change bow in top rotor housing Turn change triangle and square scrapers Grind flats on retract rollers Check V belts X Check ejector wings for wear me nn Check casing for wear and tear me X X n ERE e e kan ma ME a n e n ae od i eed n men ss enn enn en x 1 The PTO axle is dismantled and 4 lubrication nipples are lubricated with Uniway Li62 or something of similar quality 2 Bolts and nuts are tightened the first time after 8 hours and then with an interval of 50 hours 3 Two lubrication nipples are lubricated with Uniway Li62 or something of similar quality The PTO axle is dismantled and the tube connection is pulled apart cleaned and lubricated gt Two lubrication nipples are lubricated with Uniway Li62 or somethi
9. Linddana alone determines whether the remedy is to be done with repairs or changes of the defective parts In case of repairs the buyer is obligated to deliver and collect the goods sold in the workshop determined by Linddana at no expense to Linddana In case of changing the defective parts the buyer is obligated to send in the defective parts to Linddana at no expense to Linddana Linddana is entitled to changing the defective goods Linddana s responsibility only covers faults which occur within a year of the goods sold being delivered Linddana has no liability besides those stated in the present item This includes any loss the fault might cause including loss of work loss of earnings and other economical implication losses Guarantee conditions If Linddana has decided to grant a guarantee then this has faults in the construction material or manufacture A guarantee granted by Linddana does not cover faults which occur as a result of imperfect maintenance incorrect mounting changes made by the buyer or wrong use of the good The guarantee furthermore does not cover normal wear and tear or deterioration Linddana s guarantee obligation presupposes that the buyer documents that a stated fault is not due to the conditions which are exempt from the guarantee cf afore mentioned The buyer must let Linddana know in writing about any faults to the goods sold no later than 8 days after the fault should have been realized by the buyer If t
10. all the control s displays and descriptions of every display are found in appendices 1 and 2 Setting the display contrast The display contrast is set by holding the ER button in while pushing the a button or the button Work display The work display shows the rom of the rotor and the two rollers On type TP 230 250 only the roller rom is shown Rpm Rotor 1150 V1 52 V2 52 By pushing the a button or the a button the display changes between the following displays Showing the rpm of the rotor Rpm Rotor 1150 Showing the rpm of the rollers On type TP 250 only one roller rom is shown Rpm Rollers V1 52 V2 52 Showing the set knife setting in millimetres Possibility for changing the value Knife setting 12 ENTER Showing the time for the present job It is shown in hours and minutes Possibility for resetting Job Time 1 48 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 33 Showing the total work time of the machine It is shown in hours and minutes Total Time 10 18 The current temperature of the oil in Celsius Accessory Oil temperature 26C The displays shown are also available through a specific display button described below See also Appendix one User display 12 1 2 The computer s control buttons The compute
11. alterscheid type 2400 with free running and friction coupling Rights to changes in the construction and specifications without previous notice reserved PTO 820 Figure 22 Dimensional sketch TP 250 PTO Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 3155 300 1507 ik a ek fo A ANA l W pen M A umma MeS 4189 2192 520 392 Figure 23 Dimensional sketch TP 250 MOBILE TURNTABLE Figure 24 Dimensional sketch TP 250 PTO K Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 OCopyright 2008 46 16 Accessories e Tool kit incl torque wrench e Prolonged ejector tube horizontal e Extension for ejector tube vertical e Lock for ball and socket coupling TP 250 MOBILE TURNTABLE e Light boom TP 250 PTO 17 Spare parts catalogue Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008
12. an 2 am O 5 Q 3 Yellow Green eb ab O C J Cc E S amp 5 Roller REV T i Ca j c gt D N 2 D po Q Roller FWD rm N s el m N all 1 15 La A d eS ca SO tO0Z ZutAd JO JBaUUOJ Roller 2 inductive m Roller 1 in wctive Temp Sensor Red Temp Sensor White Rotor inductive Roller 2 Inductive does not exist on TP 250 External functions Not relevant for this type of ew External reverse function Mo Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 OCopyright 2008 39 12 8 Appendix 1 User display Lindana wood chipper Vergion 1 03 TP4B8 gede Soo a ii e ener Machine setup wira Vere I Code a PVG 32 i i ANN machines i kata Ren Rotion ca 4 ka 1060 ENTER f6 l Machine not I q calibrated i Ren Rollers visa Wate a l RPH Store Het Calibrated ae a kt pete B50 ENTER knife setting EGS Calibration ai Ko Pulses Reversing 35 ENTER 29 PAL 15 ENTER n i Aa eau ai Petia tg 0 eka e hl AA l garip espt 4 Total Tine z DOE Calibration Te Sr4e Pers Can mTot be done Oil tenperatura 260 Taemperaturesansor not installed Temperaturesensor installed Gal bes ting 18 C Oil heating Sense net ins ts lied Oil
13. an break when stone or metal comes in between them The machine must not be used for wood chipping of wood containing nails screws arming etc When feeding branches you must stand next to the feeding hopper see fig 1 The branches can be thrown around when the retract rollers get a hold of them Logs must be fed into the machine from the back see fig 2 i lt Efe ol WMV p a ga l a r ZE Figure 1 Feeding branches Figure 2 Feeding logs Remember to keep the knives and anvil sharp it makes feeding easier and gives a better quality chips and besides it lovers the use of fuel considerably The machine must be inspected daily meaning the rotor housing must be opened and the rotor knives anvil etc must be inspected By doing this you prevent unexpected stops and prolong the life of the machine The tractor or trailer upon which the machine is mounted must always have the brakes activated during work The machine must not e Be used for other materials than wood e Beused to push trees stubs etc There must not be equipment like forest chains axes chain saws etc in the feeding hopper Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 5 Mounting instructions 5 1 Before use The machine is equipped with a lifting point which is to be used when lifting the machine with
14. axle The machine must stand on a plane horizontal surface during use and the tractor mounted machines must be attached to the tractor s three point suspension see fig 7 The tractor s brakes must be properly activated Trailer mounted machines must also have their brakes activated see fig 8 When starting the machine Engagement must be done with the motor running at idle speed or at as few revolutions as possible in order to avoid overloading of the PTO axle gear box tractor and wood chipper Three point Hand brake suspension Figure 7 TP 250 PTO three point suspension Figure 8 TP 200 MOBILE hand brake Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 6 Safety instructions 6 1 Safety regulations e Use hearing protectors safety goggles or a similar eye protection close fitting safety clothing and safety shoes e When working near roads it can be prudent to wear a west whish reflects the light to be more visible to the other road users The displaying of signs must be in accordance with the Road Traffic Act e Minimum age for users of the machine is 18 for training and under surveillance from an adult the age is 16 e During operation all body parts must be kept away from the feeding hopper and any moveable parts of the machine e Always stand next to the feeding hopper during feeding of the mach
15. ck that the two belt discs are parallel and are aligned Then tighten the bolt and the counternut Check the belt tension again Finish by mounting the screen Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 28 Maintenance of the tow bar Maintenance schedule BPW Special Long range grease ECO Li 91 after adjustment of tow After approximately 500 For every 2 3000 km At Approximately 50 km least once a year After the first drive After all adjustments X 2 Test the adjustment of the tow bar x 3 Testthehandbrake X 4 Lubrication of ball and socket coupling x 5 Lubrication of the overrunning brake Tightening of the fastening bow Tightening of the castle nut X Lubrication of 3 nipples on the turntable for every 50 hours X ap A gt ep O q W an Service and guidance for engine See the enclosed service manual Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 OCopyright 2008 10 Hydraulics diagram TP 250 without revolution guard Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 29 30 12 Instruction for TP PILOT K Overall desc
16. d to 50 Nm 5 KPm When the anvils have been turned or replaced and all the bolts are tightened the roller housing is lowered with the top retract roller in place The spring is put back by using multigrip pliers see fig 13 Turn the rotor a few times to make sure that there are not any objects in the rotor housing Close the rotor housing and tighten the bolts see fig 15 Bolts which hold the two parts of the rotor housing together Figure 15 Tighten of bolts in the rotor housing 8 4 2 Knives The machine is equipped with three knives The knives must always be changed in sets The knives belong together in sets also when they are ground so that they are always of equal width If the knives are not of equal with the rotor will be out of balance which will lead to unnecessary strain on the bearings and vibrations in the whole machine Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 21 This is how it is done Stop the machine and the drive Uncouple the tractor s PTO Check that the rotor is at a complete standstill by looking at the two coloured axle end Turn the ejector tube so it faces away from the rotor housing fig 6 Loosen the bolts which hold the two parts of the rotor housing together and open the rotor housing The rotor is turned until the rotor lock can go into one of the holes on t
17. dations from the supplier of the PTO axle e The ejector tube must not point towards people or areas where there are people There is a safety distance of 20 m in the direction where the chips are thrown e AT DANGER PUT THE OPERATION BOW IN NEUTRAL See fig 10 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 10 e During operation the machine s height may not supersede 600 mm over the terrain see fig 9 If this height is not maintained the operation safety handle will not work as it should and that may lead to risks of severe personal injury due to retraction Figure 9 Maximum height over the terrain e During transport or when the machine is dismantled the PTO axle has to be placed in the machine s carrier bow e Incase of transport on roads the ejector tube is turned so it is placed appropriately within the width of the machine and then it is fixed securely e During transport on public roads the provisions of the authorities must be respected e During cleaning of the hopper THE RETRACT ROLLERS MUST BE STOPPED e For cleaning a broom or similar must be used Never touch the inside of the hopper when the machine is running SPECIAL TP 250 PTO K e The machine must not be fed by hand since it has been designed for feeding by a crane e There is a security zone of 20 m around the tractor and the wood
18. ddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 35 12 2 Functions An overview over the control s display can be found in appendix 1 User display An overview over every display can be found in appendix 2 Description 12 2 1 General display showings and button functions If ENTER is shown on the display it means that ea must be pushed down for two seconds in order to get access to changing values or to activate underlying displays A blinking value means that the value can now be changed with vi and a always brings the previous display back and in the end will show the work display If a value is blinking and you do not want to change this value then just push then the display is left without the value being changed in order to get access to the machine s functions and setup a code has to be entered The access to entering the code is gained by pushing the 3 and vi buttons and holding them in for two seconds then this display is shown Machine setup Code 0 User codes are code 3 and code 5 Code 3 gives access to machine setup Code 5 gives access to calibration of the rollers not relevant for this type of machine Machine setup Enter code 3 in the code entering display Then the following display is shown with the possibility to change the different machine parameters e Therpm of the rotor where the retraction of the rollers starts RPM start
19. et head as a coupling without inspection As accessory the ball and socket head can be replaced by a pintle eye The height of coupling can be adjusted from 402 mm to 922 mm l di SS po B 42 50 kg M 250 300Nm Remember split pin After adjusting the height the position must be secured by tightening the screw connection with the above factor Remember to lock the screw connection with a split pin Transport on public roads When driving on public roads the ejector tube must be turned backwards and secured against rotation During transport the locking mechanism on the turntable must be secured against rotation and secured with a ring split pin Pos A Transport Pos B Work position The retractable hopper must also be tipped up and secured with a ring split pin When coupling the 7 13 pole connector and the safety chain must be coupled to the vehicle The supporting leg must be raised The hand brake is released before driving Check the lights and the brakes before driving Measurements of the trailer Width 2200 mm Length 4200 mm Height 3200mm Tire assembly 165R13C 8 Tire pressure cold max 450 kPa 65 psi 4 5 bar In order to avoid destroying the electrical system the following points must be respected 1 The ignition key must never be in neutral during operation 2 The earth connections must be clean 3 When using a battery charger the ea
20. foreign bodies Figure 6 Position of ejector tube when opening rotor Check that the gap between the knives and the anvil is correct 0 7 mm The knives have a fixed knife position 13mm Check that the knives are not rubbing on the anvils Lift the top part of the rotor housing back in place and tighten the bolts Check that all bolts nuts and screws are tightened properly Remember to lubricate all the lubrication points see maintenance schedule page 16 Old hydraulics and motor oil and used oil filters and air filters must be handed in at an approved receiving station Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 5 2 Mounting instruction The machine is designed to be mounted on the tractor s three point suspension or trailer mounted with its own engine Machines for mounting on the tractor s three point suspension is delivered with a PTO axle with either 1 3 8 6 splines or 1 3 8 21 splines At 1000 rpm certain types of tractors a PTO axle with 1 3 8 21 splines must be used The PTO axle must be mounted with free running on the machine side Linddana uses Walterscheid 2400 with free running which comes with the machine The length of the PTO axle has to be adapted to the tractor following instructions from the supplier of the PTO axle See the attached manual for the PTO
21. he buyer does not let Linddana Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 44 know before the expiration of this deadline and before the guarantee period runs out the buyer looses the right to make any claims concerning the fault Linddana is entitled and obligated to remedy any faults which are covered by a guarantee granted by Linddana Linddana alone decides if the remedy is to be done as repairs or changes of the defective parts everything under the terms stipulated in item 4 Linddana has no other liability for those faults This includes any loss the fault might cause including loss of work loss of earnings and other economical implication losses The guarantee does not cover e fa defect with just cause can be attributed to inappropriate use e Use of unoriginal spare parts including worn parts e Wrong adjustment or use of the machine e Use of wrong lubricant or hydraulic oil e Wear on cross at PTO axle e Tightening spring for rollers e V belts e Knives and anvil which break because of foreign bodies in the machine Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 45 15 Technical data wood chipper Rotor disc diameter mm 960 0 0 PTO transmission axle W
22. he rotor Now the rotor is locked see fig 16 Be careful that your fingers are not near the knives when the rotor is turned Rotor lock Figure 16 Locking the rotor with rotor lock Remove the four nuts which hold the knife to the rotor Take out the knife The bearing surfaces on the chipping disc and the knife must be cleaned properly before fitting the knives On fitting the nuts must be slightly greased u 0 125 meaning thin oil WD 40 or something similar Copper grease MoS or similar low friction grease must not be used Check that the distance between the knife s edge and the anvil is set correctly at 0 7 mm The nuts must be tightened with 95 Nm 9 5 KPm Use a torque wrench for this which is included in the tool kit This can be bought as an accessory When the knives are changed the rotor is turned a few times to make sure that there are not any objects in the rotor housing Close the rotor housing and tighten the bolts see fig 15 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 22 8 4 3 Scrapers and facing plate The machine is equipped with three square scrapers on the rotor disc a triangle scraper in the rotor housing and a facing plate in the ejector tube see fig 17 Figure 17 Placement of the scrapers and the facing plate The purpose of the scrapers is to remove any material wh
23. heating TEL Dil hestings B minutter Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 40 Appendix 2 Description of user display Start display Display Lindana wood chipper Information Version 1 14 TP250 Shows the software version as well as machine type 12 8 1 Work displays Rom Rotor O Information Main display V1 0 V2 0 Current rpm on rotor Current rpm on roller 1 and roller 2 Rpm Rollers TP 230 250 Current rpm on rollers Rpm Rotor Information 0 Current rpm on only the rotor Can be used if this information in overwritten by fault messages in the main display Rpm Rollers Information V1 0 V2 0 Current rpm on only the rollers Can be used if this information in overwritten by fault messages in the Rpm Rollers TP 230 250 main display Knife setting Information 15 ENTER Knife setting in mm Can be changed by holding the enter button in for two seconds Job Time Information 0 16 ENTER Current job time in hours and seconds The job time is only registered when the rollers are running The job time can be reset by holding the enter button in for two seconds Total Time Information 0 16 Show the machine s total work time in hors and minutes The total time is only registered when the retract rollers are running Oil temperature Information 26 C The current temperat
24. hine and the drive Uncouple the tractor s PTO Check that the rotor is at a complete standstill Turn the ejector tube so it faces the opposite direction of the rotor housing fig 6 Loosen the bolts which hold the two parts of the rotor housing together and open the rotor housing With multigrip pliers the spring is lifted off the top retract roller and the roller housing is lifted and secured with the locking pawl see fig 13 Dismantle the three bolts which hold the horizontal anvil This is done from the outside and from below The anvil is taken out and turned replaced Before the anvil is put back the anvil and the bearing surface must be cleaned carefully The distance between the knife s edge and the anvil must be 0 5 0 9 mm See fig 14 The tightening factor for the bolts for the horizontal anvil is 200 Nm 20 KPm Accessory in the tool kit there is a torque wrench BER E F j TOL f e ee Figure 14 Distance between anvil and knife Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 20 The vertical anvil is unscrewed and removed from the inside Before a new one is put in the anvil and the bearing surface must be cleaned carefully The anvil is set to a distance of 0 5 0 9 mm to the knives Use a new precision feeler gauge The bolts for the vertical anvil are tightene
25. ich might get stuck to the knives At the same time the square scraper on the rotor removes material which falls off in front on the chipping disc This reduces the wear to the casing and reduces the consumption of fuel The square scrapers can be turned once before being changed while the triangle scraper and the facing plate should always be changed when they are worn This is how it is done The rotor is turned until the rotor lock can go into one of the holes on the rotor Now the rotor is locked see fig 16 Be careful that your fingers are not near the knives when the rotor is turned Dismantle the countersunk bolts which hold the square scraper on the rotor Turn the square so that a sharp edge points up Clean the block and the bearing surface Put the square scraper back If it is worn on two edges the square scraper has to be changed Always change the square scraper on the rotor in sets Change the triangle scraper when it is worn The facing plate is mounted in the top part of the rotor housing and can easily be changed by dismantling three bolts on the outside of the rotor housing If chip quality is not important the facing plate in the ejector tube can be removed This will increase the capacity of the machine and save fuel The facing plate has to be dismantled when chipping wet conifer with a lot of needles Then a good ejection is ensured When the scrapers have been turned or changed the rotor is turned a few times to ma
26. il Mount or change the sliver breaker Not enough effect on the PTO axle or the engine Change the scrapers Change the ejector wings Remove the facing plate in the top part Increase speed to maximum revolutions Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 43 14 Guarantee obligation for wood chipper The guarantee is valid for 24 months after date of purchase for the relief of faults which are provable to the material or manufacture The guarantee covers defective components which are repaired or changed Transportation costs and wages for changes are the responsibility of the customer Upon any claims the changed parts must be sent to Linddana for investigation Linddana alone decides whether the claim can be approved The following is an excerpt from Linddana s Terms of Sales and Delivery item 4 and 5 Claims Any and all risk concerning the goods is passed to the buyer at the time of delivery of the goods A claim concerning the goods has to be done in writing to Linddana as quickly as possible and no later than 8 days after delivery If Linddana has not received the claim before the deadline stated the objections to quantity and quality that the buyer might have will lapse Linddana is entitled and obligated to correct any and all faults which are caused by the construction material or manufacture
27. il as well as used oil filters and air filters should be handed in to the local receiving station Lubrication nipples are lubricated according to the maintenance schedule with Statoil Uniway Li62 or a similar product The machine is equipped with a hydraulic oil tank which is integrated in the rotor housing The tank is equipped with a filler neck an air release valve a level glass and a return filter When changing the hydraulic oil the filler neck is opened see fig 12 The drain plug is unscrewed The oil is drained into a canister for proper removal When the tank is almost empty the tank is sucked empty with an oil suction device The drain plug is screwed back and new hydraulic oil is slowly filled in 25 litres for TP 250 Oil is filled in until the level glass is half filled Filler neck Level glass Figure 12 Filling hydraulic oil 8 3 Maintenance of the retract rollers The retract rollers pull the material into the rotor disc and the knives The plates on the bottom retract roller must be kept sharp in order to keep the retract force Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 18 This is how it is done Stop the machine and the drive Uncouple the tractor s PTO Check that the rotor is at a complete standstill Turn the ejector tube so it faces the opposite direction of the rotor housi
28. ine Always observe the terrain conditions around the machine It can be dangerous to fall near the machine e Before starting the machine check that the safety devices are working properly Especially the stop and return functions on the operation bow e The machine must not be started without the ejector tube mounted to the machine e Never use the machine in closed or poorly ventilated spaces because of the danger of carbon monoxide poisoning e The top part of the machine as well as all other shielding must not be opened removed before the rotor disc is completely immovable and the tractor s motor is stopped e Always stop the machine and the tractor during inspections service or repairs The machine must be uncoupled from the tractor s PTO e Tractor mounted machines have to be on the ground before service or repairs are done e Always remove the keys from the machine and or the tractor before leaving it e After maintenance and repairs the machine must not be started before all bolts are tightened and all safety devices are mounted e Three point mounted machines must be coupled to the tractor s three point suspension before use e The maximum rpm for the machine 1000 rom must not be superseded e The transmission axle s tube shielding and covering must always be intact Safety chains on the transmission axle have to be properly mounted e The length of the PTO axle has to be adapted to the tractor according to the recommen
29. ironmental INSUHUCTIONS ap et ata bs aa ao ae n ak a ao e na ka e n a e n a Epa on Bra e ee kaa A 13 7 Operation of the machine ws kissvas aie sikse aesinasaryo a ees ake ss ate sise dhassosns pase fes sekodsisanes s 14 7 1 Table 1 Regulating the number of revolutions for the retract rollers veeeereeeorerosnsoe 15 SB MaiMteNANC sierra arr a die eee kana vos sete eya sese sesa aaa dosae Se AOU 16 8 1 Maintenance schedule 523 area iT orne 16 8 2 UL aye erste alles are ie a kat n ne tri nue si reer ot nner meee SEE ES nee ny ete Ee eee nea eee e eee 17 8 3 Maintenance of the retract FOER vas ee ba data id daf Dat ia ak a pwal dala laid daj tied vi a a ata 17 8 4 EMAN EI NS WONN DAT S l a ete a e a ek n a e a ae e e etik de e e a a a taa ka e aid saat 19 8 5 Grinding Of KAN VE Ske aktik pa a a ka kk pak e kn n a n a kd at ke e kan kk a a aba ea eka oak tas aks 25 9 Special instruction for TP 250 MOBILE TURNTABLE ccccccscsccsceccscecescees 26 10 Hydraulics diagram TP 250 without revolution guard csccsccsceccsceees 29 11 Hydraulics diagram TP 250 with revolution guard ccccsccsccscsccsceccscccs 29 12 Instruction Tor TP PILOT iii bien e s sis abo iooidone saa siek ane vas tea ass povitesse des ssaeeeaaws 30 12 1 Description of the TP PILOT K control panel rieeteeeeetereeeseoeeestoooeosooooosooooosoooonasononoooe 31 122 FUNC UON Satan aaa e a a a a a kk ka n kn a at a ate sles et a aa a e a a n
30. k the operation bow It is now necessary to release the reset handle before the operation bow can be moved into the middle position A and the rollers can pull the material into the machine This reset handle is a safety measure so you cannot start the rollers by accident so they pull material into the machine Operation bow woz Figure 10 Feeding hopper TP 250 with operation bow reset handle and extracted funnel handle Reset handle Funnel handle B A mon Q Q O Direction to the operation bow STOP OOo Fr Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 OCopyright 2008 15 By turning the adjusting screw on the flow valve you can find the correct rom Never go to fast with the rollers because the wood will work like a brake if the pressure on the rotor is too big with the ensuing increase in use of fuel Branches can get wrapped around the rollers if the rom is too high In the table below table 1 are stated the recommended rpm on the retract rollers at a desired chip length The speeds vary with the number of revolutions on the PTO axle The chip length can be regulated on the flow regulation valve on the wood chipper for smaller chip lengths than indicated in the table 7 1 Table 1 Regulating the number of revolutions for the retract rollers Chip length Rotor 10 mm 13 mm Model Rpm TP250 PTO 1000 17 2
31. ke sure that there are not any objects in the rotor housing Close the rotor housing and tighten the bolts see fig 15 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 23 8 4 4 Casing The TP 250 is equipped with an interchangeable casing at the bottom of the rotor housing The casing absorbs the wear and tear which would normally happen at the bottom of the rotor housing This is how it is done Stop the machine and the drive Uncouple the tractor s PTO Check that the rotor is at a complete standstill Turn the ejector tube so it is pointing away from the rotor housing see fig 6 Loosen the bolts which hold the two parts of the rotor housing together and open the rotor housing Remove the top part of the rotor housing Dismantle the six bolts and nuts which hold the casing to the bottom part of the rotor housing see fig 18 Hit with a hammer on the part of the casing which sticks up over the edge of the rotor housing at the hinge side to loosen the casing Now the casing can be swung out Casing Figure 18 Changing the casing Before a new casing is put in you must clean the bottom of the wood chipper Mount the new casing with six bolts Put the top part of the rotor housing back When the casing has been changed the rotor is turned a few times to make sure that there are not any objects in the r
32. ng fig 6 Loosen the bolts which hold the two parts of the rotor housing together and open the rotor housing With multigrip pliers or something similar the spring is lifted off the top retract roller Grab the handle and open the roller housing and push the locking pawl into the lock in the side plate fig 13 The roller housing is now secured from falling down Now the flats on the bottom retract roller can be grounded with an angle grinder Turn the rotor carefully with the operation bow in position forward or reverse By doing this the retract roller is turned so all the plates can be ground Remember that the welding seams are not to be ground away Locking pawl Figure 13 Securing with locking pawl When the roller has been grounded the top retract roller is lowered back in place The spring is put back with multigrip pliers Close the rotor housing and screw the bolts back Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 19 8 4 Changing worn parts 8 4 1 Anvil The anvil in the machine is used as wearing bar for the knife in order to cut the wood The anvil must be sharp edged otherwise the wood will bend down and the cut will become frayed The machine is equipped with one horizontal anvil with two edges and one vertical anvil The vertical anvil can be turned This is how it is done Stop the mac
33. ng of similar quality 6 Changed for the first time after 50 hours and then every 1000 hours 7 Drain the hydraulic oil and fill with new oil using 25 litres of Hydraway HVXA 46 or oil that has the equivalent specifications The interval between changing oil can be extended by using biodegradable hydraulic oil such as the type Hydraway SE 46 HP and taking oil samples on an ongoing basis 8 The anvil is turned changed depending on need The bow in the top rotor housing is changed depending on need if it is mounted 10 The triangle scraper in the rotor housing is turned changed The square scraper on the rotor is turned changed 11 The retract rollers are sharpened 2 The tightening of the V belts is checked Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 17 8 2 Lubrication and oil The Wood Chipper is as standard factory filled with hydraulic oil of the type Hydraway HVXA 46 When replacing the oil use the same type of oil or oil with equivalent specifications Do not mix together different types brands of oils As an accessory the Wood Chipper can be delivered factory filled with biodegradable oil of the type saturated ester Hydraway SE 46HP When replacing the oil use the same type of oil or oil with equivalent specifications Do not mix together different types brands of oils Old hydraulic oil and engine o
34. otor housing Close the rotor housing and tighten the bolts see fig 15 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 24 8 4 5 Adjusting the V belts Pump transmission The retract rollers are run hydraulically The hydraulic pump to the retract rollers is run by V belts The V belts need to be check regularly or when the belts are suspected to be slack This is how it is done Stop the machine and the drive Uncouple the tractor s PTO Check that the rotor is at a complete standstill Turn the ejector tube so it faces away from the rotor housing fig 6 Loosen the bolts which hold the two parts of the rotor housing together and open the rotor housing Loosen the four screws which hold the hydraulic pump in place and adjust the tension by turning the adjusting screw Used belts are allowed to bend 5 87 mm when they are pushed down with 50 54 N 5 5 4 kg for new belts this number is 57 61 N 5 7 6 1 kg See fig 19 The belts can be measured with a gauge for this purpose which can be bought as an accessory Measure point for tension Figure 19 Adjusting the tension When the V belts have been tightened the rotor is turned a few times to make sure that there are no objects in the rotor housing Now the rotor housing has to be closed and the bolts have to be tightened see fig 15 Linddana A S lholm
35. pilled oil must be cleaned up and handed in at an approved receiving station Worn out parts must be disposed of for recycling When the machine is worn out it must be disposed of properly Hydraulic oil and engine oil must be drained and handed in at an approved receiving station with oil filters and air filters The rest of the machine must be disposed of for recycling Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 14 7 Operation of the machine The wood chipper is equipped with two hydraulic rollers a pressure compensated flow valve a control valve an operation bow with a reset handle and a funnel handle see fig 10 The funnal is hinged To make it easier to open and close the folding infeed funnel used the funnel handle that pulled out Funnel handle is pushed back after opening and closing of the funnel The operation bow must be in the stop position 0 during start see fig 11 After start you release the reset handle and pull the operation bow into the middle position A and the rollers will turn The material is now pulled into the machine By pulling the operation bow towards you B the flow of oil in the control valve is turned and the rollers reverse the material is now pushed out of the machine When the machine is either stopped 0 or reversed B the reset handle will automatically bloc
36. pm of the rollers When the display is active the LED will light up If the control is put in reverse an LED will light up no matter which display is showing in order to indicate that the rollers are in reverse If the percentage difference between the rollers is larger than the entered value the LED will blink no matter which display is shown At the same time an alarm will sound Not TP 250 Display change to showing the time registered for job When the display is active the LED will light up A new push will change display to showing the machine s total time Push ENTER in for two seconds Display change to showing oil temperature When the display is active the LED will light up If a sensor has been put in the current temperature will be shown If a sensor has not been put in and Temp Oil Heating is smaller than 99 the error message Sensor error will be shown If a sensor has not been put in and Temp Oil Heating is 99 the message Sensor not installed will be shown The switch will move to the middle position when it is not being pushed Switch up is not an issue on this type of machine A short push down will entail the rollers reversing the number of pulses which have been set in the control Holding the switch down entails the rollers reversing while the switch is held down For both functions an alarm will also sound Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlin
37. r s control buttons are described below Display change and changing entry values ENTER button Change to entry display approving an entry and start calibration The ESC button is used to delete an entry of a value or to leave a given display and go to the preceding display Repetitive pushing will always result in the showing of the work display Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 34 12 1 3 Display buttons with LEDs Display change to showing the rpm of the rotor When the display is active the LED will light up Display change to showing the knife setting entered When the display is active the LED will light up Possibility for changing the knife setting Display change to display for oil heating When the display is active the LED will light up A new push which is held for two seconds will start the heating of the oil The oil heating will only start if the oil temperature is lower than Temp Oil Heating or if a sensor has not been put in If a sensor has been put in the oil temperature will be shown If a sensor has not been put in the time from the start of heating will be shown in minutes When the oil is heating an LED will blink The oil heating will stop when the temperature reaches Temp Oil Heating Or by pushing the button again Display change to showing the r
38. ription of the system During normal operation of the machine the desired chip size is set by setting the position of the knives and punching in the setting of the knifes followed by a calibration of the rollers The wood chipper can now be used by putting the rom of the knife over the set start value where the rollers start pulling in wood material As long as the rom of the rotor are between the low and high limit value the rollers will rotate so the material between the rollers will be pulled toward the knives The rpm of the rollers will be adapted to the rpm of the knives so the desired chip size is maintained It is recommended that the 12 V power supply is run through an emergency stop button which removes the power supply to the PILOT K and the crane Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 31 12 1 Description of the TP PILOT K control panel Below is an overview of the control panel for the control with specification of the placement of the buttons and switches Display with two lines Rpm Rotor 1150 VI 52 V2 52 The computer s control Display buttons with LEDs Factor switch buttons Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 32 12 1 1 Display Overview of
39. rth cable on the battery must be dismantled Instruction for wood chipper See TP 250 PTO Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 2 Service and guidance for engine See the enclosed service manual or www hatz com Engagement of the wood chipper At cold starts Start the engine Set the throttle so the engine runs smoothly at low revolutions Let the engine run 30 60 seconds depending on the temperature Then the wood chipper is engaged slowly and the rpm are increased to working speed full throttle At warm starts Same approach is followed Only it is not necessary to let the engine heat up before engaging The wood chipper must not be engaged at full throttle When stopping Let the wood chipper run out of material Disengage the wood chipper Let the engine run idle for approximately 30 seconds before the throttle is turned to stop Turn the ignition key to neutral See symbols on the starter box F min 25 1N RA Fmax 27 1N Check of V belts and wood chipper Stop the engine and make sure the rotor is stopped Dismantle the outer screen over the V belts If the belts need tightening Loosen the bolts which hold the wood chipper to the engine console The tightening bolt is tightened so the wood chipper is pushed to the side Che
40. spinning satisfactorily Not enough oil in the hydraulics system The flow valve is screwed out too far The stationary roller is blocked The bypass valve is dirty The revolution guard is blocking The operation bow is in the O position The rollers are not pulling satisfactorily Not enough flow The V belts are too slack The hydraulic oil gets too hot Too poor viscosity of the hydraulic oil The hydraulic filter is clogged The oil pump is worn or damaged The oil engine is defective The pressure control valve in the control valve is dirty Chip quality is not satisfactory The knives are dull The anvil is worn The knives are worn too far down lt 106 mm The distance between knife and anvil is too big Sliver breaker not mounted or worn Poor ejection of the chips Not enough drive Scrapers are worn Ejector wings are worn The facing plate in the top part Not enough revolutions on the machine Fill up with hydraulic oil Turn up the flow Clean under and behind the roller Clean the bypass valve Increase the rpm on the rotor Put the operation bow in the A position The flow valve is turned opened Tighten the V belts Let the machine cool down while checking why Change the hydraulic oil Change the hydraulic filter Change the hydraulic pump Change the oil engine Clean the pressure control valve Grind the knives Turn change the anvil Change the knives Adjust the distance between the knives and anv
41. the TP 250 PTO have been measured during use at 1000 rpm on the rotor disc powered by a tractor The sound effect level and the sound pressure level from the TP 250 MOBILE have been measured during use at 930 rpm on the rotor disc powered by the Hatz 4L41C motor engine The measurements have been conducted according to test provisions Directive 2000 14 EC 3 July 2000 EN ISO 3744 1995 ISO 11201 1995 ISO 4871 19 March 1997 EN 13525 17 February 2005 The guaranteed sound effect level which will be given by the manufacturer according to directive 2000 14 EC are as follows TP 250 PTO 127 dB A re 1pW TP 250 MOBILE 127 dB A re 1pW The machine s sound pressure level at the operator s seat is measured according to ISO 11201 at TP 250 PTO 110 dB A TP 250 MOBILE 109 dB A The above mentioned values have the common uncertainty for the method of measuring and the estimated variation in a product line for the type of machine Detailed information on the measurements and results as well as estimation of uncertainty are found in a thorough report which can be given out on demand The sound level is of such a character that hearing protectors are prescribed during use of the machine 6 4 Environmental instructions When changing hydraulic oil or engine oil oil and used oil filters and air filters must be handed in at an approved receiving station Oil spills must be avoided as much as possible At oil spills the s
42. und with 2 second intervals At the same time the LED will blink at the button with the roller symbol Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 37 12 4 Alarms Alarms are always activated with sound There are alarm for Temperature sensor fault Temperature too low Temperature too high Too big difference on the rpm of the rollers Both rollers are stopping Manual reverse of rollers Manual open rollers Temperature alarms and roller alarms are sounded with 5 beeps Manual reverse and manual open rollers are sounded with 2 beeps 12 5 Comments Pay attention to not performing welds on the machine where the control is mounted without disconnecting all cables power supply sensors communication etc from the control and it is recommended that the ground cable for the welder is put in the near vicinity of where the welding is going to take place If these recommendations are not followed the control can suffer irreparable damage 12 6 Technical data Power supply 12V dc Temperature range O C 50 C Fuses T3 2A 250V Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 OCopyright 2008 38 12 7 Electrical mounting On Off Machine Colour Code 1 Bl fe 6 r
43. ure of the hydraulic oil in Celsius Oil temperature Sensor not Information installed The sensor is not put in and Temp Oil Heating is set for 99 Oil heating Information 10 C The current temperature of the hydraulic oil in Celsius Oil heating Information Sensor not installed The sensor is not put in and Temp Oil Heating is set for 99 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 Copyright 2008 41 Display Oil heating Information 10 minutes The sensor is not put in and Temp Oil Heating is set for 99 Shows how long the oil heating has been activated 12 8 2 Machine setup code 3 1000 ENTER Rotor rpm for start of retraction 850 ENTER Value of stop for retraction at too low rotor rpm Pulses Reversing Information 15 ENTER Desired number of pulses the rollers should reverse Temp Oil Heating Information 26 C The temperature the oil must have before start of retraction is started This value must be set at 99 if the sensor has not been put in Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpQlinddana com www linddana com User instructions TP 250 K from 02 11 2015 OCopyright 2008 42 13 Troubleshooting for wood chipper TP 250 Check possible causes before contacting the distributor Problem Possible cause Solution S The rollers are not
Download Pdf Manuals
Related Search