ECO LED PAR39 Model #555-11407
Contents
1. ECO LED PAR39 Model 555 11407 USER MANUAL Distributed Exclusively By MCM Electronics www mcmelectronics com WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH YOLTAGE RISK OF ELECTRIC SHOCKI Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the equipment Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution Never remove warning or informative labels from the equipment Do not open the equipment and do not modify the equi2. 96 127 Fade In Out 0 255 Spect 224 255 Sound Action When set to DMX 3 channel mode Technical Specification Number of LED s 60 tri color each red green blue Power supply 120VAC 60Hz IW 14W 5 1 2 x 5 1 2 x 5 Weight Warranty MCM Custom Audio and Stellar Labs products are warranted by MCM Electronics against manufacturer defects for a period of two years from the original date of purchase This warranty is limited to manufacturer defects in either materials or workmanship MCM Electronics or any other worldwide divisions of Premier Farnell PLC are not responsible for any consequential or inconsequential damage to any other component structure or the cost of installation or removal of said items For questions or specific information regarding warranty replacement or repair contact MCM Electronics www mcmelectronics com 800 543 4330
3. fades strobes chases and other effects In this case all lamps would be set in DMX slave mode with the DMX controller set as the DMX master All Stellar Labs LED PAR lamps utilize industry standard DMX 512 protocols and are compatible with any such DMX controllers and lighting devices Installation Lighting fixtures may be mounted in any angle or desired arrangement Thankfully LED lighting not only uses considerably less power less than 20W but give off virtually no heat greatly increasing flexibility and use Lamps are equipped with a 3 prong grounded cord and should be connected only to appropriate grounded AC outlets If using multiple lamps in a DMX controlled setup only appropriate 3 pin DMX cables should be used Using microphone or other similar cable may cause erratic and unpredictable results Also when connecting multiple DMX lamps in a chain a DMX terminator should be placed at the end of that chain to ensure reliable operation All DMX cables terminators light stands and specially designed AC outlet strips are available at MCM Electronics as well as a variety of other music and lighting suppliers Menu The following flow chart shows the menu arrangement for programming the lamp for a desired operation mode The terminology and layout of this menu is typical of most DMX controlled lighting products and experienced users will merely need to refer to this for any information needed However if you are new to DMX contr
4. the lamp to make gradual blend changes between colors This is easily accomplished as follows Press the M button to revert back to the master menu The menu should read CHAN If not Use the and buttons to scroll the menu until CHAN appears Press the Y button one time the LED will read MIX The display should now show a number between M000 and M255 Use the Land buttons to select a setting between 000 and 255 this will control how fast the lamp blends from one color to the next 255 being the highest rate Once the desired setting is obtained press the OK button Much like the sound activated mode the lamp will now act as a self contained device or as a DMX master controlling others connected after it in a DMX chain General Menu Explanation It will be necessary to set this lamp to specific DMX address locations for use with complex DMX controllers Additionally other information will be needed to identify the operation of this lamp with used in a chain with non similar DMX devices The following is intended to provide detail on these items as well as a general explanation of each of the menu settings Menu Display This allows setting of the first DMX channel of the lamp This may be set to any DMX address from 001 to 512 This allows the unit to be set in either 3 channel or 5 channel DMX mode Available settings are 5CH and 3CH This allows the LED display to be turned off after setup is complete This is ideal in
5. equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property Introduction There are multiple modes in which this light may operate depending upon the specific needs of the user These include Stand alone DMX master and DMX slave In stand alone mode the lamp may be set to automatically scroll through various color change patterns at user selected speeds with user selected fade or to strobe a user specified color and rate An internal microphone also allows sound activated mode allowing the color change to be synchronized to music If multiple lamps are used they may all be set to stand alone mode above and each will operate completely independently with independent rates and color changes However in multi lamp setups it is often desirable to have all lamps operating together scrolling strobing or fading between colors in unison In this case the lamps may be connected together using specified 3 pin DMX cables with the first lamp set in automatic mode and as the DMX master with all subsequent lamps set as the DMX slave For even more complex setups a separate DMX controller may be used enabling complex combinations of
6. ol some simple setup instructions following the menu will prove helpful Note viewing this manual electronically from www mcmelectronics com will allow zooming in on the following chart making some symbols more readable DMX Address DMX Display 2 Sound PE Red Value la A coa oa Y Down Green Value Green Value SESTE 8 Poe Blue Value Blue Value HESA Strob Speed SWINE SLAN Slave DMA Slave JADMX FARER Basic Setup For new users the following should prove helpful It will take you through the steps of setting the lamp for automatic or sound activated mode with information on setting one unit as the master controller with multiple units connected operating in unison with that control Steps for use Connect the LED PAR lamp to a suitable AC power source The LED display will read AddR Press the button one time the LED will read Press the OK button the LED will read Press the OK button again the LED will read Press the OK button the LED will still read Press the M button twice the LED will read SET DMX 3CH 3CH SET The unit is now setas a three channel DMX master controller Press the button one time the LED will read Press the button one time the LED will read Press the b
7. on on the menu The and buttons may be used to scroll up and down on the menu If this second lamp is the only other to be used a DMX terminator should be connected to the 3 pin female DMX output connector If additional lamps are to be used they should be set to slave mode and connected exactly as shown above with the terminator placed at the end of the chain Other self contained modes Besides the above sound activated mode the master unit may also be set to automatically scroll through its available colors This may be done with hard changes from color to color or gradual fades both with varying speeds To see this in action use the following steps Use the and buttons to scroll the menu display to the AddR position Press the Y button one time the LED will read SET Press the Y button again the LED will read CHAN Press the OK button the display will still read CHAN The display should now show a number between C000 and C255 The lamp should now be automatically scrolling through multiple colors There will be a small dot illuminated on the lower right side of the LED display The displayed number represents the rate in which the lamp automatically changes color 000 the slowest and 255 the fastest Use the Yand buttons to adjust this setting Once the desired setting is obtained press the OK button In this mode you will see the lamp is making hard changes from one color to the next It may be desirable for
8. pment Do not connect this equipment to a dimmer pack Do not switch the equipment on and off in short intervals as this will reduce the system s life Only use the equipment indoors Do not expose to flammable sources liquids or gases Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable Make sure that the available voltage is between 110 120VAC Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your dealer for service Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this
9. situations where visibility of the display in a dark setting may be undesirable Available settings are ON and OFF This allows setting of the rate change for hard color changes Available settings are C000 C255 This allows setting of the rate change for color blends Available setting are M000 M255 This setting turns the sound activation on Sole available setting is SOUd This allows testing of all brightness levels of each available LED color This is useful for periodic testing of the lamp for burned out LED s This may also be used if a lamp is to be used as a simple fixed color of virtually any color This allows any brightness setting of the red LED s Available settings are ROOO R255 This allows any brightness setting of the green LED s Available settings are G000 G255 This allows any brightness setting of the blue LED s Available settings are BOOO B255 Note that any of the colors above may be blended to provide virtually any desired output color This will put the lamp in strobe mode flashing the color that was selected in the steps immediately above Available settings are S000 S255 This places the lamp in slave mode Sole available setting is SLAV When all lamps are to be externally controlled by a DMX controller the following information will be helpful When set as to DMX 5 channel mode RED GREEN BLUE Speed Strobe 07255 0255 07255 0 31 color Setting 0 15 0FF 32 63 Fade Out 16 255 Strobe
10. utton one time the LED will read Press the OK button the LED will read CHAN MIX SOUd SOUd There will be a small blinking dot on the lower right side of the LED display The unit is now in sound activated mode Tapping the unit with your finger will cause it to randomly change color The microphone will now pick up sounds within the room such as music causing the unit to change colors to the beat of the music This unit is set as the DMX master and is in sound activated mode You may connect additional lamps to slave from this by utilizing the female 3 pin DMX output connection Using a suitable DMX cable connect this 3 pin output to the 3 pin input of a second lamp and set that lamp to slave mode it will follow exactly the color changes of the first lamp Steps for setting lamp to slave mode Connect the LED PAR lamp to a suitable AC power source The LED display will read AddR Press the Y button one time the LED will read Press the Y button again the LED will read Press the Y button again the LED will read Press the Y button again the LED will read Press the Y button again the LED will read Press the Y button again the LED will read Press the OK button the LED will read SET CHAN MIX SOUd TEST SLAV SLAV This unit is now in slave mode and will copy the action of the first unit in the chain You are now at the end of the address list pressing the y button again will revert back to the AddR positi
Download Pdf Manuals
Related Search