xPC560S EVB User Manual 1.00.book
Contents
1. e Po XPC560SEVBUM efe TM Rev 1 00 freescale June 2008 Alliance Member Purchase Agreement P amp E Microcomputer Systems Inc reserves the right to make changes without further notice to any products herein to improve reliability function or design P amp E Microcomputer Systems Inc does not assume any liability arising out of the application or use of any product or circuit described herein This software and accompanying documentation are protected by United States Copyright law and also by International Treaty provisions Any use of this software in violation of copyright law or the terms of this agreement will be prosecuted All the software described in this document is copyrighted by P amp E Microcomputer Systems Inc Copyright notices have been included in the software P amp E Microcomputer Systems authorizes you to make archival copies of the software and documentation for the sole purpose of back up and protecting your investment from loss Under no circumstances may you copy this software or documentation for the purpose of distribution to others Under no conditions may you remove the copyright notices from this software or documentation This software may be used by one person on as many computers as that person uses provided that the software is never used on two computers at the same time P amp E expects that group programming projects making use of this software will purchase a cop2. 4 xPC560SADPT144S HARDWARE 8 JUMPER SETTINGS 4 1 Boot Configuration The following jumpers affect the operation of the processor as it initially comes out of the reset state J7 FABM Configuration Controls whether the processor boots from internal FLASH or from a serial interface CAN SCI Jumper Setting Effect 142 The MPC560xS processor uses serial boot mode 2 3 default The MPC560xS processor uses internal boot mode J8 ABSO Configuration If J7 is configured for serial boot mode this jumper selects between UART or CAN If J7 is configured for internal boot mode this jumper has no effect Jumper Setting Effect The MPC560xS processor uses the CAN interface for serial boot mode 142 The MPC560xS processor uses the UART interface for 2 3 default f serial boot mode 28 xPC560S EVB User Manual RE micro www pemicro com PsV Figure 4 1 Boot Configuration Jumpers 4 2 Power Configuration When the xPC560S Mini Module is plugged into the xPC56XXMB motherboard power is supplied directly by the motherboard In this setup the external power supply input available on the Mini Module should NOT be used When the xPC560S Mini Module is used as a stand alone board an external 5V or 3 3V power supply must be used Note that when using the xPC560S Mini Module as a stand alone board only one power supply is available 5V or 3 3V and all appropriate ju
3. PsV PsV SN74LVCIGOS PsV Figure 5 3 Reset circuitry schematic xPC560S EVB User Manual 49 RE micro www pemicro com 6 xPC560SADPT208S HARDWARE 8 JUMPER SETTINGS 6 1 Boot Configuration The following jumpers affect the operation of the processor as it initially comes out of the reset state J7 FABM Configuration Controls whether the processor boots from internal FLASH or from a serial interface CAN SCI Jumper Setting Effect 142 The MPC560xS processor uses serial boot mode 2 3 default The MPC560xS processor uses internal boot mode J8 ABSO Configuration If J7 is configured for serial boot mode this jumper selects between UART or CAN If J7 is configured for internal boot mode this jumper has no effect Jumper Setting Effect The MPC560xS processor uses the CAN interface for serial boot mode 142 The MPC560xS processor uses the UART interface 2 3 default for serial boot mode 50 xPC560S EVB User Manual RE micro www pemicro com Figure 6 1 Boot Configuration Jumpers 6 2 Power Configuration When the xPC5608 Mini Module is plugged into the xPC56XXMB motherboard power is supplied directly by the motherboard In this setup the external power supply input available on the Mini Module should NOT be used When the xPC5608 Mini Module is used as a stand alone board an external 5V or 3 3V power supply must be
4. An xPC560S Evaluation Kit includes the following items One xPC56XXMB Motherboard One xPC560SADPT1448 or xPC560SADPT 1768 or xPC560SADPT208S Mini Module One xPC56XX Resources CD ROM One P amp E USB ML PPCNEXUS Hardware Interface Cable One USB A to B Cable Freescale Warranty Card An xPC560S Adapter Package includes the following items One xPC560SADPT144S or xPC560SADPT 1768 or xPC560SADPT2088 Mini Module One xPC56XX Resources CD ROM Freescale Warranty Card 1 2 Supported Devices The xPC560SADPT 1448 Mini Module supports the following devices MPC5606SEMLQ 144LQFP The xPC560SADPT 1768 Mini Module supports the following devices MPC5606SEMLU 176LOFP The xPC560SADPT208S Mini Module supports the following devices MPC5606SEMMG 208BGA 1 3 Recommended Materials Freescale MPC5606S reference manual and datasheet xPC56XXMB schematic xPC560SADPT100S schematic xPC560SADPT144S schematic xPC560SADPT208S schematic xPC560S EVB User Manual RE micro www pemicro com 1 4 Handling Precautions Please take care to handle the package contents in a manner such as to prevent electrostatic discharge xPC560S EVB User Manual RE micro www pemicro com 2 HARDWARE FEATURES The xPC560S EVB is an evaluation system for Freescale s MPC560xS microprocessors A 38 pin Mictor Nexus port and or a 14 pin JTAG port are provided on the Mini Module to allow usage of an external PowerPC Nexus interface
5. 19 RE micro www pemicro com 20 J30 LIN2 SCI RxD selection Controls whether the RxD pin on LIN2 or SCI is connected to the default I O pin on the MPC560xS processor Jumper Setting Effect The LIN2 RxD pin is connected to the PI7 pin on 142 the MPC560xS processor This should be set if enabling LIN2 33 The SCI RxD pin is connected to the PI7 pin on the MPC560xS processor Figure 3 5 LIN2 schematic xPC560S EVB User Manual RE micro www pemicro com SCI One SCI interface is available on the xPC56XXMB J16 SCI TxD Enable Jumper Setting Effect On default Enables SCI transmit Off Disables SCI transmit J17 SCI RxD Enable Jumper Setting Effect On default Enables SCI receive Off Disables SCI receive J27 LIN1 SCI TxD selection Controls whether the TxD pin on LIN1 or SCI is connected to the default VO pin on the MPC560xS processor Jumper Setting Effect The LIN1 TxD pin is connected to the PB3 pin on the MPC560xS processor 142 xPC560S EVB User Manual 21 RE micro www pemicro com 2 3 The SCI TxD pin is connected to the PB3 pin on the MPC560xS processor This should be set if enabling SCI J28 LIN1 SCI RxD selection Controls whether the RxD pin on LIN1 or SCI is connected to the default
6. Jumper Setting Effect 1 2 default Debug port s are configured for 5V logic 2 3 Debug port s are configured for 3 3V logic J18 3 3V MCU Power Enable Allows 3 3V to be selected for the various power pins on the MPC560xS processor Jumper Setting Effect On default 3 3V is available to power the various power supply pins on the MPC560xS processor Off 3 3V cannot be used to power any of the various power supply pins on the MPC560xS processor J22 VDDE A Voltage Selection Sets the voltage level on the MPC560xS VDD IO B and VDD IO C xPC560S EVB User Manual RE micro www pemicro com power pins Jumper Setting Effect MPC560xS VDD IO B and VDD IO C pins are 142 default powered by 5V J14 must be ON MPC560xS VDD IO B and VDD IO C pins are powered by 3 3V J18 must be ON 243 J16 VDDR Voltage Selection Sets the voltage level on the MPC560xS VDD IO A power pin Jumper Setting Effect MPC560xS VDD IO A is powered by 5V J14 must 1 2 default be ON e MPC560xS VDD IO A is powered by 3 3V J18 must be ON 243 J25 VDDE E Voltage Selection Sets the voltage level on the MPC560xS VDD IO D power pin Jumper Setting Effect MPC560xS VDD IO D is powered by 5V J14 must 142 default be ON e 32 xPC560S EVB U
7. VDD IO F is powered by 3 3V J18 must be ON J23 VDDE B Voltage Selection Sets the voltage level on the MPC560xS VDD IO A and VDD IO E power pins Jumper Setting Effect 1 2 default MPC560xS VDD IO A and VDD IO E are powered by 5V J14 must be ON 56 MPC560xS VDD IO A and VDD IO E are powered by 3 3V J18 must be ON xPC560S EVB User Manual RE micro WWW pemicro com J27 VDDA Voltage Selection Sets the voltage level on the MPC560xS VDD ADC power pin Jumper Setting Effect 142 default MPC560xS VDD ADC is powered by 5V J14 must be ON 243 MPC560xS VDD ADC is powered by 3 3V J18 must be ON 6 3 System Clock Configuration The xPC560S Mini Modules support the usage of crystal clock sources as well as external clock sources J10 Crystal clock source enable Both of the jumpers below need to be installed to enable the crystal clock Source Jumper Setting Effect 142 default The MPC560xS OSCIN signal is connected to the crystal clock source on the xPC560S Mini Module 3 4 default The MPC560xS OSCOUT signal is connected to the crystal clock source on the xPC560S Mini Module J11 External clock source enable The xPC5608 Mini Module contains a footprint for an SMA connector which xPC560S EVB User Manual 57 RE micro www pemicro com can be used
8. iese esse ee ee ee ke ee ee ee es 5 2 2 Pin Numbering for J mpoets ic tied tx ene tte asp A 8 3 xPC56XXMB HARDWARE 8 JUMPER SETTINGS nnee ennen 10 3 1 Power Supplies tere RR daa 10 3 2 LEDS EE AE 13 3 3 BUHONSE ER RE ER A 14 3 4 A 15 3 5 CAIN 23 3 6 Potentlomieter ico o ae o t o m ah 25 3 7 Ned AR EE E E A E OR EE 27 4 xPC560SADPT144S HARDWARE 8 JUMPER SETTINGS 28 4 1 Boot Conflg ratloris oi recreo b P e E p Ev de 28 4 2 Power Configuration RR ais 29 4 3 System Clock Configuration ees se ee ee Re ee AR ke ee ee Re ee ee ke ee ee 35 4 4 General Configuration eiie eese tnnt din EE Ee nana 37 5 xPC560SADPT176S HARDWARE 8 JUMPER SETTINGS 39 5 1 Boot Conflguratlon itae t ceder etta eve ba te ovp adde decas 39 5 2 Power ConfIgUratlon e niit a i De GE aqu AC Masa ER GES Ra Re 40 5 3 System Clock Configuration escria 46 5 4 General Configuration ee ee ee ee ee ee Re ee AR ee ee nennen nnns 48 6 xPC560SADPT208S HARDWARE 8 JUMPER SETTINGS 50 6 1 Boot Configuration cic eet nee teen dc e n dcs 50 6 2 Power Configuration nnn ee ee eene nnns 51 6 3 System Clock Configuration nnee ee ke ee ee Re ee ee ke ee ee 57 6 4 General Configuration cisco et Ee GE adr eb d re eode eL uae Ge 59 xPC560S EVB User Manual DE
9. www pemicro com Off MPC560xS VDD 1V2 pins are left disconnected J17 Debug Port Voltage Configuration Sets the logic voltage level on the 14 pin JTAG port and 38 pin MICTOR port if available These ports are used by external interface hardware to communicate with the processor Jumper Setting Effect 1 2 default Debug port s are configured for 5V logic 243 Debug port s are configured for 3 3V logic J18 3 3V MCU Power Enable Allows 3 3V to be selected for the various power pins on the MPC560xS processor Jumper Setting Effect 3 3V is available to power the various power supply On default pins on the MPC560xS processor Off 3 3V cannot be used to power any of the various power supply pins on the MPC560xS processor J22 VDDE A Voltage Selection Sets the voltage level on the MPC560xS VDD IO B VDD IO C and 42 xPC560S EVB User Manual RE micro WWW pemicro com VDD IO G power pins Jumper Setting Effect 142 default MPC560xS VDD IO B VDD IO C and VDD IO G pins are powered by 5V J14 must be ON 243 MPC560xS VDD IO B VDD IO C and VDD IO G pins are powered by 3 3V J18 must be ON J16 VDDR Voltage Selection Sets the voltage level on the MPC560xS VDD IO A power pin Jumper Setting Effect 1 2 default MPC560xS VDD IO A is po
10. 3RXD RT INH me pz ge OE o OP13 DL OTE Figure 3 8 Low Speed CAN schematic 3 6 Potentiometer A potentiometer is available on the xPC56XXMB to allow an analog voltage input J18 POT Enable Jumper Setting Effect xPC560S EVB User Manual 25 RE micro www pemicro com 26 On default The potentiometer wiper terminal is connected to the PBO pin on the MPC560xS processor Off The potentiometer wiper terminal is left disconnected VIO Figure 3 9 Potentiometer schematic xPC560S EVB User Manual micro WWW pemicro com 3 7 Pin Mapping The following is the xPC560S EVB pin assignment for the Pin Array headers LJ 0 RXDO PB2 TXDO PB3 RXD1 PB12 TXD1 PB13 GND 5 PCSO 2 PB5 PCSO 3 PB D Port B PB1 Pria Pri2 PFi5 Pri3 PG15 PG13 PG11 PGO PG7 PGS PG3 PGI dIE PHI4 PH1i2 SV PHi5 PH13 xPC560S EVB User Manual pe a Pro j PF7 j Pro PHIO PH8 PH6 PH4 PH11 PH9 PH7 PHS Figure 3 10 Pin Mapping Port A K PAO PAI PA2 PA3 PAA PAS PAG PA7 Pag PA9 PA10 PA11 PA12 PA13 PA14 PA15 PKO PkKi PJ8 Port PEO PES PEG PES PELA 5V GND LPR PFO PH2 PHO PH3 PHi 27 RE micro www pemicro com
11. WWW pemicro com US C24 C25 J6 12V V EUS LIN L TXD 4 gy 1 LRD 1D NE EOS js Jer LA 3 o Vus t ed JEN exp B MC33661 DOF VDDS y p3 x R20 m E OO O PN Lm MA N x IN_EN TASTER EN FIA 1K Jes ci Tur J31 LIN2 pin2 configuration Figure 3 4 LIN1 Schematic Jumper Setting On Effect Off default J19 LIN2 enable Pin 2 of the LIN2 connector is connected to 12V Jumper Setting On Pin 2 of the LIN2 connector is not connected to 12V Effect Off default Enables the LIN2 transceiver Disables the LIN2 transceiver xPC560S EVB User Manual DE micro www pemicro com J20 LIN2 master selection Jumper Setting Effect On LIN2 is configured as a master node Off default LIN2 is configured as a slave node J21 LIN2 pin1 configuration Jumper Setting Effect On Pin 1 of the LIN2 connector is connected to 12V Off default Pin 1 of the LIN2 connector is not connected to 12V J29 LIN2 SCI TxD selection Controls whether the TxD pin on LIN2 or SCI is connected to the default VO pin on the MPC560xS processor Jumper Setting Effect The LIN2 TxD pin is connected to the PI6 pin on the 142 MPC560xS processor This should be set if enabling LIN2 The SCI TxD pin is connected to the PI6 pin on the 2 3 MPC560xS processor xPC560S EVB User Manual
12. ge aad Lf apa hax ao de ee oS A o 13 r d y Lt 8 MR REST te 5 Gema REET C9 25 gt LESIMB 2j B RST EN pO e r AD id e E 7 Ed sal r EED VER 1 sm ADM6315 26D3ARTZ de T PsV 60 Figure 6 3 Reset circuitry schematic xPC560S EVB User Manual RE micro www pemicro com 7 DEBUGGING PROGRAMMING THE xPC560S EVB P amp E provides hardware and software tools for debugging and programming the xPC560S EVB system P amp E s USB ML PPCNEXUS and Cyclone MAX offer two effective hardware solutions depending on your needs The USB ML PPCNEXUS is a development tool that will enable you to debug your code and program it onto your target The Cyclone MAX is a more versatile and robust development tool with advanced features and production programming capabilities as well as Ethernet support More information is available below to assist you in choosing the appropriate development tool for your needs 7 1 Hardware Solutions At A Glance The USB ML PPCNEXUS offers an affordable and compact solution for your development needs and allows debugging and programming to be accomplished simply and efficiently Those doing rapid development will find the USB ML PPCNEXUS easy to use and fully capable of fast paced debugging and programming The Cyclone MAX is a more complete solution designed for both development and production The Cyclone MAX features multiple communications interfaces including USB Ethe
13. signal is connected to the crystal clock source on the xPC560S Mini Module J11 External clock source enable The xPC5608 Mini Module contains a footprint for an SMA connector which can be used to provide an external clock source to the system Jumper Setting Effect On The MPC560xS EXTAL signal is connected to the SMA connector on the xPC560S Mini Module Off default xPC560S EVB User Manual The SMA connector on the xPC560S Mini Module is disconnected from the processor 47 RE micro www pemicro com Rs CS VSS OSC 0 Ohm 22pF Rf Yl orsi n r ED NX8045GB 8 000M C9 VSS OSC 22pF CLOCK CIRCUIT P2 DO NOT POPULATE SMA CONNECTOR Figure 5 2 System Clock schematic 5 4 General Configuration J13 Reset Enable A RESET push button on the xPC560S Mini Module can be used to reset the processor Jumper Setting Effect 48 xPC560S EVB User Manual RE micro www pemicro com The RESET button on the xPC560S Mini Module is On default bled enable The RESET button on the xPC560S Mini Module is Off j disabled J27 Reset Pullup The RESET signal of the MPC560xS processor can be pulled up to a logic high voltage Jumper Setting Effect The RESET signal on the MPC560xS processor is 142 pulled up to 5V The RESET signal on the MPC560xS processor is 2 3 pulled up to 3 3V
14. 4 6 The TxD pin of the CAN H interface is connected to the PB11 pin of the MPC560xS processor xPC560S EVB User Manual 23 RE micro www pemicro com J13 CAN L CTE Jumper Setting Effect On Enables CAN transmission Off default Disables CAN transmission J11 CAN L TxD RxD Enable Controls which I O pins on the MPC560xS processor are connected to the TxD and RxD pins on CAN L Jumper Setting Effect 143 The RxD pin of the CAN L interface is connected to the PB1 pin of the MPC560xS processor 3 5 default The RxD pin of the CAN L interface is connected to the PB10 pin of the MPC560xS processor 2 4 The TxD pin of the CAN L interface is connected to the PBO pin of the MPC560xS processor 4 6 default The TxD pin of the CAN L interface is connected to the PB11 pin of the MPC560xS processor 24 xPC560S EVB User Manual ero WWW pemicro com VDDS VDDS 7 SCs OluF nF ns 5 CNRXA gt CNTXA 43 4 E JO CNRXQ CNIXC DBl TJA1050T 14 TE CAN Interface Circuit AN DB9M Figure 3 7 High Speed CAN schematic rd VDDS J12 12VVDD 5 1 2 1X2 HEADER N 218 DB2 zE m 3 CNRXA CNIXA 7 E CNRXC CNIXC gt R
15. Effect MPC560xS VDD IO E is powered by 5V J14 must 1 2 default be ON e 34 xPC560S EVB User Manual RE micro WWW pemicro com 243 MPC560xS VDD IO E is powered by 3 3V J18 must be ON J26 VDDA Voltage Selection Sets the voltage level on the MPC560xS VDD ADC power pin Jumper Setting Effect 1 2 default 243 MPC560xS VDD ADC is powered by 5V J14 must be ON MPC560xS VDD_ADC is powered by 3 3V J18 must be ON 4 3 System Clock Configuration The xPC560S Mini Modules support the usage of crystal clock sources as well as external clock sources J10 Crystal clock source enable Both of the jumpers below need to be installed to enable the crystal clock Source Jumper Setting Effect 142 default The MPC560xS EXTAL signal is connected to the crystal clock source on the xPC560S Mini Module 344 default The MPC560xS XTAL signal is connected to the crystal clock source on the xPC560S Mini Module xPC560S EVB User Manual RE micro www pemicro com 36 J11 External clock source enable The xPC5608 Mini Module contains a footprint for an SMA connector which can be used to provide an external clock source to the system Jumper Setting Effect On The MPC560xS EXTAL signal is connected to the SMA connector on the xPC560S Mini Module Off default T
16. Gro www pemicro com 7 DEBUGGING PROGRAMMING THE xPC560S EVB mme 61 7 1 Hardware Solutions At A Glance unne ee ee ee ee ee nn ee ee 61 7 2 Working With P amp E s USB ML PPCNEXUS ese see ee ee ee ee ee ee ee see ee ee ee ede ee ee 62 7 3 Working With P amp E s Cyclone MAX ese ese ee ee ee ee ee ee ee ee de ee ee ee ee ee ee 63 iii xPC560S EVB User Manual RE micro www pemicro com 1 OVERVIEW The xPC560S EVB is an evaluation system supporting Freescale MPC560xS microprocessors The complete system consists of an xPC56XXMB Motherboard and an xPC560SADPT Mini Module which plugs into the motherboard Different Mini Modules are available for evaluating devices with different footprints in the MPC560xS family of microprocessors The evaluation system allows full access to the CPU all of the CPU s I O signals and the motherboard peripherals such as CAN SCI LIN The Mini Module may be used as a stand alone unit which allows access to the CPU but no access to the I O pins or any motherboard peripherals 5V Standalone Reset Debug 12V Power Input Supply Button Connections VO Headers UN 335 119 TD ORDE a pori it t omi A TN kl tn Disa E 8 i D PUES y and Buttons High Speed Left Low Speed Right Trimmer Figure 1 1 Overview of the xPC560S EVB xPC560S EVB User Manual 1 RE micro www pemicro com 1 1 Package Contents
17. ME 1 l 1 voc gt P p eee A Ls 3 ee eg Reser qo peerage i IE errie n MR REST 08 bod o Se B 1 1 EN Jy Jl 3 we 5 a bee po i ET Ia ADM6315 26D3ARTZ Lo Eum Psv Figure 4 3 Reset circuitry schematic 38 xPC560S EVB User Manual DE micro WWW pemicro com 5 xPC560SADPT176S HARDWARE amp JUMPER SETTINGS 5 1 Boot Configuration The following jumpers affect the operation of the processor as it initially comes out of the reset state J7 FABM Configuration Controls whether the processor boots from internal FLASH or from a serial interface CAN SCI Jumper Setting Effect 142 The MPC560xS processor uses serial boot mode 2 3 default The MPC560xS processor uses internal boot mode J8 ABSO Configuration If J7 is configured for serial boot mode this jumper selects between UART or CAN If J7 is configured for internal boot mode this jumper has no effect Jumper Setting Effect The MPC560xS processor uses the CAN interface for serial boot mode 142 The MPC560xS processor uses the UART interface 2 3 default for serial boot mode xPC560S EVB User Manual 39 RE micro www pemicro com PsV Figure 5 1 Boot Configuration Jumpers 5 2 Power Configuration When the xPC560S Mini Module is plugged into the xPC56XXMB motherboard power is supplied directly by the motherboard In this setup the exte
18. barrel connector Figure 2 1 xPC56XXMB Top Component Placement 2 1 xPC560SADPT Mini Module Board Features Can be used as a stand alone board by providing external 5V power supply input ON OFF Power Switch w LED indicator Reset button with filter and LED indicator xPC560S EVB User Manual 5 RE micro www pemicro com e xPC560SADPT100S has socket for MPC560xS in 100LQFP footprint xPC560SADPT 1448 has socket for MPC560xS in 144LQFP footprint xPC560SADPT208S has socket for MPC560xS in 208BGA footprint Debug ports 38 pin Mictor Nexus port and or 14 pin JTAG port Direct clock input through SMA connector footprint only Jumpers for boot configuration EXTERNAL SU DR 3U3 is 2 000000000000 000000000000 se v 900000000000 A roo lo MPC5 0xS COMPATIBLE Y pe Ud E E ale Str SU ZET U5 0 AE SPCEEDSK COMPATIBLE R OD oo RESET c 5 isl x 000000000000 000000000000 00000000000 000000000000 Oo OC oo OIO loo B 000000000000 RS E mn Ninn DARON ON arra ENEN BESS eje eee veo 000000000000 000000000000 EZI HEC 610 Cer TEL O O O Leser Conk E A 8 E 3 El 8 E a goon o CSL ain EN Figure 2 2 xPC560SADPT144S Top Component Placement xPC560S EVB User Manual micro www pemicr
19. micro www pemicro com 3 2 LEDs There are four user LEDs available on the xPC56XXMB All LEDs are active low J7 LEDs Enable Controls whether the LEDs on the xPC56XXMB motherboard are connected to I O pins of the processor The jumpers can be removed and wires can be used to connect each LED to any processor I O pin if desired Please note that although the schematics indicate that the processor I O pins are eMIOSx those are not the I O pins for the xPC560S EVB The table below has the correct pins listed Jumper Setting Effect 142 default on LED1 connected to PE4 3 4 default on LED2 connected to PES 5 6 default on LED3 connected to PE6 7 8 default on LED4 connected to PE7 VIO Kx Figure 3 2 LEDs circuitry schematic xPC560S EVB User Manual 13 RE micro www pemicro com 3 3 Buttons There are four user buttons available on the xPC56XXMB J8 Buttons Enable Controls whether the buttons on the xPC56XXMB motherboard are connected to l O pins of the processor The jumpers can be removed and wires can be used to connect each button to any processor I O pin if desired Please note that although the schematics indicate that the processor I O pins are eMIOSx those are not the I O pins for the xPC560S EVB The table below has the correct pins listed Jumper Setting Effect 142 default on KEY1 connected to PEO 3 4 de
20. programmed to 3 3V efault J5 Regulators Enable amp Standby Jumper p Position Effect Setting On The power regulator is always on 1 2 Off The power regulator is in standby if jumpers default 5 6 are also in the off position 5 VSB VSC and VSD tracking regulators are n disabled 3 4 Off VSB VSC and VSD tracking regulators are default enabled ON Th lator is al e power regulator is always on default E y 5 6 Off The power regulator is in standby if jumpers 1 2 are also in the off position On Vo and Vcore regulators are disabled 7 8 off Voi and Vcore regulators are enabled default xPC560S EVB User Manual 11 RE micro www pemicro com 5 amp 6 should ON 12 J36 VIO Peripherals Logic Level Jumper Setting 142 Effect Onboard peripherals are configured for 3 3V logic 2 3 default Onboard peripherals are configured for 5V logic J37 VBat low voltage detection Jumper Setting Effect On Low battery detection is enabled Off default Low battery detection is disabled ua Figure 3 VEFEREEGEET 1 BRA System Power 1 Power Supply circuitry schematic xPC560S EVB User Manual RE
21. such as P amp E USB ML PPCNEXUS cable and Cyclone MAX automated programmer xPC56XXMB Board Features ON OFF Power Switch w LED indicators A 12VDC power supply input barrel connector Onboard ST Microelectronics L9758 regulator provides three different power voltages simultaneously 5V 3 3V and 1 2V Onboard peripherals can be configured to operate at 5V or 3 3V logic levels Two CAN channels with jumper enables One CAN channel with High Speed transceiver and DB9 male connector One CAN channel with Low Speed Fault Tolerant and High Speed transceiver selectable with jumpers and DB9 male connector Two LIN channels with jumper enables One channel with transceiver and pin header connector populated e One channel with footprints only One SCI channel with jumper enables Transceiver with DB9 female connector Two FlexRay channels with jumper enables One channel with transceiver and DB9 male connector e One channel with footprint only Four user push buttons with jumper enables and 0 or 1 forcing configurable xPC560S EVB User Manual DE ero www pemicro com Four user LED s with jumper enables One potentiometer for analog voltage input Pin array for accessing all VO signals Expansion connectors for accessing all I O signals Development zone with 0 1 spacing and SOIC footprint prototyping e Specifications e Board Size 5 5 x 9 0 e 12VDC Center Positive power supply with 2 5 5 5mm
22. to provide an external clock source to the system Jumper Setting Effect The MPC560xS EXTAL signal is connected to the On SMA connector on the xPC560S Mini Module The SMA connector on the xPC560S Mini Module is Off default ult disconnected from the processor A c Jh 0 Ohm 22pF i Rf IM Ohm XL DO NOT POPULAS EI NX8045GB 8 000M 2X2 HEADER C9 22pF qh CLOCK CIRCUIT P2 DO NOT POPULATE SMA CONNECTOR Figure 6 2 System Clock schematic 58 xPC560S EVB User Manual DE micro www pemicro com 6 4 General Configuration J13 Reset Enable A RESET push button on the xPC560S Mini Module can be used to reset the processor Jumper Setting Effect On default The RESET button on the xPC560S Mini Module is enabled Off The RESET button on the xPC560S Mini Module is disabled J28 Reset Pullup The RESET signal of the MPC560xS processor can be pulled up to a logic high voltage Jumper Setting Effect 142 The RESET signal on the MPC560xS processor is pulled up to 5V 243 The RESET signal on the MPC560xS processor is pulled up to 3 3V xPC560S EVB User Manual 59 micro www pemicro com PSV Psv y T Is BSV Bey p tus 25 laRST PULLUP ES 10 Ohm R8 RIO AIK QAT Aa REDLED 6 4 Psv PN J Us w o O RIG D3 reer SN74LVCIGOS ME 1 47K Yue
23. 560xS VDD IO D power pin Jumper Setting Effect MPC560xS VDD IO D is powered by 5V J14 must 1 2 default be ON e MPC560xS VDD IO D is powered by 3 3V J18 must be ON 2 3 54 xPC560S EVB User Manual RE micro WWW pemicro com J21 VDDMC Voltage Selection Sets the voltage level on the MPC560xS VDD SMD C power pin Jumper Setting Effect MPC560xS VDD SMD C is powered by 5V J14 142 default must be ON MPC560xS VDD SMD C is powered by 3 3V J18 must be ON 243 J20 VDDMB Voltage Selection Sets the voltage level on the MPC560xS VDD SMD B power pin Jumper Setting Effect MPC560xS VDD SMD B is powered by 5V J14 142 default must be ON MPC560xS VDD SMD B is powered by 3 3V J18 must be ON 243 J19 VDDMA Voltage Selection Sets the voltage level on the MPC560xS VDD SMD A power pin Jumper Setting Effect xPC560S EVB User Manual RE micro www pemicro com 1 2 default MPC560xS VDD_SMD_A is powered by 5V J14 must be ON 243 MPC560xS VDD SMD A is powered by 3 3V J18 must be ON J24 VDDE C Voltage Selection Sets the voltage level on the MPC560xS VDD IO F power pin Jumper Setting Effect 142 default MPC560xS VDD IO F is powered by 5V J14 must be ON 243 MPC560xS
24. I O pin on the MPC560xS processor Jumper Setting Effect 142 The LIN1 RxD pin is connected to the PB2 pin on the MPC560xS processor 2 3 The SCI RxD pin is connected to the PB2 pin on the MPC560xS processor This should be set if enabling SCI l0 MAX TXD2 9 MAX RXD2 J16 MAX TXD1 1 S TXDA 11 TXD_EN MAX RXD1 1 12 E S RXDA o 1 0uF RXD EN bd MAX RXD2 1 MAX TXD2 2 HOST R2 3 li HOST T2 4 C22 Tio 1 0uF VDD5 22 Figure 3 6 SCI schematic xPC560S EVB User Manual DE micro www pemicro com 3 5 CAN Two CAN interfaces are implemented on the xPC56XXMB a high speed CAN interface and a low speed CAN interface J14 CAN H Transmit Enable Jumper Setting Effect On Enables CAN transmission Off default Disables CAN transmission J15 CAN H TxD RxD Enable Controls which I O pins on the MPC560xS processor are connected to the TxD and RxD pins on CAN H Jumper Setting 1 3 default Effect The RxD pin of the CAN H interface is connected to the PB1 pin of the MPC560xS processor 345 The RxD pin of the CAN H interface is connected to the PB10 pin of the MPC560xS processor 2 4 default The TxD pin of the CAN H interface is connected to the PBO pin of the MPC560xS processor
25. Systems Inc P O Box 2044 Woburn MA 01888 www pemicro com Freescale and the Freescale logo are trademarks of Freescale Semiconductor Inc All other product or service names are the property of their respective owners Freescale Semiconductor Inc 2007 XPC560SEVBUM Rev 1 00 June 2008 eos a yclone MAX
26. e xPC56XXMB motherboard and the xPC560S Mini Modules have a rounded corner to indicate the position of pin 1 See examples below for the numbering convention used in this manual for jumper settings xPC560S EVB User Manual RE micro WWW pemicro com 1 2 1 2 3 3 4 2 5 6 3 7 8 3 pin single row Horizontal 3 pin single row Vertical Jumper Jumper 8 pin double row Vertical Jumper Figure 2 5 Pin Numbering xPC560S EVB User Manual RE micro www pemicro com 3 xPC56XXMB HARDWARE 8 JUMPER SETTINGS 3 1 Power Supplies The xPC56XXMB obtains its power from the 12VDC Center Positive input barrel connector The following jumpers are used to configure the power supply output J3 VSA Tracking Regulator Configuration Jumper Setting Effect The ST L9758 tracking regulator VSA tracks the input On voltage at its TRACK REF pin Off default The ST L9758 tracking regulator VSA tracks 5V J4 VPROG Regulators Control Jumper P Position Effect Setting On Vkam regulator output is programmed to 1V 142 Off Vkam regulator output is programmed to 1 5V default On Verpy regulator output is programmed to 2 6V 344 Off Verpy regulator output is programmed to 3 3V default 10 xPC560S EVB User Manual RE micro WWW pemicro com 546 On Vo regulator output is programmed to 2 6V Off default Vo regulator output is
27. er Setting Effect On default Enables the LIN1 transceiver Off Disables the LIN1 transceiver J23 LIN1 master selection Jumper Setting Effect On LIN1 is configured as a master node Off default LIN1 is configured as a slave node J24 LIN1 pin1 configuration Jumper Setting Effect 16 xPC560S EVB User Manual RE micro WWW pemicro com On Pin 1 of the LIN1 connector is connected to 12V Off default Pin 1 of the LIN1 connector is not connected to 12V J27 LIN1 SCI TxD selection Controls whether the TxD pin on LIN1 or SCI is connected to the default VO pin on the MPC560xS processor Jumper Setting Effect 142 The LIN1 TxD pin is connected to the PB3 pin on the MPC560xS processor This should be set if enabling LIN1 243 The SCI TxD pin is connected to the PB3 pin on the MPC560xS processor J28 LIN1 SCI RxD selection Controls whether the RxD pin on LIN1 or SCI is connected to the default VO pin on the MPC560xS processor Jumper Setting Effect 142 The LIN1 RxD pin is connected to the PB2 pin on the MPC560xS processor This should be set if enabling LIN1 243 The SCI RxD pin is connected to the PB2 pin on the MPC560xS processor xPC560S EVB User Manual 17 18
28. fault on KEY2 connected to PE1 5 6 default on KEY3 connected to PE2 7 8 default on KEY4 connected to PE3 J9 Buttons Driving Configuration Selects whether the buttons drive logic high or drive logic low when pressed Jumper Setting Effect is When pressed buttons will send logic high to the connected I O pin When pressed buttons will send logic low to the 2 3 default connected I O pin J40 Buttons Idle Configuration 14 xPC560S EVB User Manual RE micro www pemicro com Selects whether the I O pins are pulled logic high or pulled logic low This controls the defaultlogic level of the I O pins when the buttons are not pressed Jumper Setting Effect I O pins connected to the buttons are pulled up to 1 2 default logicihieh I O pins connected to the buttons are pulled down to logic low 2 3 O luF O luF 4 INPUT SWITCHES Figure 3 3 Buttons circuitry schematic 3 4 LIN There are footprints for two LIN connections on the xPC56XXMB By default one LIN circuit is assembled LIN1 and the other circuit is left unpopulated xPC560S EVB User Manual 15 RE micro www pemicro com LIN2 J6 LIN1 pin2 configuration Jumper Setting Effect On Pin 2 of the LIN1 connector is connected to 12V Off default Pin 2 of the LIN1 connector is not connected to 12V J22 LIN1 enable Jump
29. he SMA connector on the xPC560S Mini Module is disconnected from the processor xPC560S EVB User Manual RE micro www pemicro com Rs lcs VSS OSC ma N N vm A mm a a ee u r 0 Ohm dx Remis SS 4 skaad eus 4 L x1 EL or POPULATE ZI NxX8045GB 8 000M CLK EN A O ui V 1 he 1122pF CLOCK CIRCUTT P2 DONOT POPULATE SMA CONNECTOR 1 PAS ps X AL EXTAL a 1 e 4 eS 2 A CLK EXT EN gt l TT e R14 EE yd GEEN 100R E Figure 4 2 System Clock schematic 4 4 General Configuration J13 Reset Enable A RESET push button on the xPC560S Mini Module can be used to reset the processor Jumper Setting Effect xPC560S EVB User Manual 37 RE micro www pemicro com On default The RESET button on the xPC560S Mini Module is enabled Off The RESET button on the xPC560S Mini Module is disabled J28 Reset Pullup The RESET signal of the MPC560xS processor can be pulled up to a logic high voltage Jumper Setting Effect bus The RESET signal on the MPC560xS processor is pulled T up to 5V 548 The RESET signal on the MPC560xS processor is pulled T up to 3 3V PSV Psy i Ds Hi 4 PsV PsV la pis leiRsr PULLUP iua RS 4 drio al 471K 4 447K REDLED pog Psv P3V3 j oa US T w RIG D3 REST SN74LVCIGOS d 1 CATK NRSTLED
30. in JTAG port and 38 pin MICTOR port if available These ports are used by external interface hardware to communicate with the processor Jumper Setting Effect 1 2 default Debug port s are configured for 5V logic 2 3 Debug port s are configured for 3 3V logic J18 3 3V MCU Power Enable Allows 3 3V to be selected for the various power pins on the MPC560xS processor Jumper Setting Effect 3 3V is available to power the various power supply On default pins on the MPC560xS processor 3 3V cannot be used to power any of the various Off power supply pins on the MPC560xS processor J22 VDDE A Voltage Selection Sets the voltage level on the MPC560xS VDD IO B VDD IO C and VDD IO G power pins Jumper Setting Effect xPC560S EVB User Manual 53 RE micro www pemicro com MPC560xS VDD IO B VDD IO C and 142 default VDD IO G pins are powered by 5V J14 must be ON MPC560xS VDD IO B VDD IO C and 2 3 VDD_IO_G pins are powered by 3 3V J18 must be ON J16 VDDR Voltage Selection Sets the voltage level on the MPC560xS VDD IO A power pin Jumper Setting Effect MPC560xS VDD IO A is powered by 5V J14 must 142 default be ON e MPC560xS VDD IO A is powered by 3 3V J18 must be ON 243 J26 VDDE E Voltage Selection Sets the voltage level on the MPC
31. level on the MPC560xS VDD IO F power pin Jumper Setting Effect MPC560xS VDD IO F is powered by 5V J14 must 1 2 default be ON e MPC560xS VDD IO F is powered by 3 3V J18 must be ON 243 J23 VDDE B Voltage Selection Sets the voltage level on the MPC560xS VDD IO A and VDD IO E power pins Jumper Setting Effect xPC560S EVB User Manual 45 RE micro www pemicro com MPC560xS VDD IO A and VDD IO E are 142 default powered by 5V J14 must be ON MPC560xS VDD IO A and VDD IO E are powered by 3 3V J18 must be ON 243 J26 VDDA Voltage Selection Sets the voltage level on the MPC560xS VDD ADC power pin Jumper Setting Effect MPC560xS VDD ADC is powered by 5V J14 must 1 2 default be ON e MPC560xS VDD ADC is powered by 3 3V J18 must be ON 243 5 3 System Clock Configuration The xPC560S Mini Modules support the usage of crystal clock sources as well as external clock sources J10 Crystal clock source enable Both of the jumpers below need to be installed to enable the crystal clock source Jumper Setting Effect The MPC560xS EXTAL signal is connected to the 142 default crystal clock source on the xPC560S Mini Module 46 xPC560S EVB User Manual RE micro WWW pemicro com 3 4 default The MPC560xS XTAL
32. manufacturing floor For production the Cyclone MAX may be operated interactively via Windows based programming applications as well as under batch or dll commands from a PC Once loaded with data by a PC it can be disconnected and operated manually in a stand alone mode via the LCD menu and control buttons The Cyclone MAX has over 3Mbytes of non volatile memory which allows the on board storage of multiple programming images When connected to a PC for programming or loading it can communicate via the ethernet USB or serial interfaces 7 3 2 Software The Cyclone MAX comes with intuitive configuration software and interactive xPC560S EVB User Manual 63 RE micro www pemicro com 64 programming software as well as easy to use automated control software The Cyclone MAX also functions as a full featured debug interface and is supported by Freescale s CodeWarrior as well as development software from P amp E P amp E s Cyclone MAX is also available bundled with additional software as part of various Development Packages In addition to the Cyclone MAX these Development Packages include in circuit debugging software flash programming software a Windows IDE and register file editor xPC560S EVB User Manual Freescale Controller Continuum 68HCO08 5S08 RS08 S 12 X ColdFire V1 ColdFire V2 V3 V4 PowerPC Nexus ARMY 2008 P amp E Microcomputer Systems Inc All rights reserved P amp E Micrcomputer
33. mpers must be configured to use that power supply The following jumpers affect the power supply pins of the MPC560xS processor J4 VIO Voltage Selection Controls whether certain VO pins are powered using 5V or 3 3V In particular xPC560S EVB User Manual 29 RE micro www pemicro com this controls the voltage of the reset circuit and the logic high voltage for the FABM and ABSO pins Jumper Setting Effect 1 2 default VIO voltage is 5V 2 3 VIO voltage is 3 3V J14 5V MCU Power Enable Allows 5V to be selected for the various power pins on the MPC560xS processor Jumper Setting Effect 5V is available to power the various power supply On default pins on the MPC560xS processor 5V cannot be used to power any of the various Off power supply pins on the MPC560xS processor J15 1 2V Core Voltage Enable Controls whether power is provided to the VDD 1V2 pins on the MPC560xS processor Jumper Setting Effect MPC560xS VDD 1V2 pins are connected to 1 2V On default power 30 xPC560S EVB User Manual RE micro WWW pemicro com Off MPC560xS VDD 1V2 pins are left disconnected J17 Debug Port Voltage Configuration Sets the logic voltage level on the 14 pin JTAG port and 38 pin MICTOR port if available These ports are used by external interface hardware to communicate with the processor
34. o com o E P 2 E n 000000000000000 000000000000000 zo 180000000000000 d O es 00 a js 00000000000000 000000000000000 000000000000000 I B TO su amp n BDOT i 80 BE O 2 B o d 23 Str 9T EEC ST aem RST_EN O O P RESET E MPCE UxS COMPATIBLE SO amp 2 Q Q Q Q Q Q Q Q O o Q o o 98 oo oo oo oo le 98 oo 20 oo oo oo oo Oo 00000000000000 000000000000000 000000000000000 H 9 EMENE sini NGS Rane San var EZI PEC BIC OT TEL Figure 2 3 xPC560SADPT176S Top Component Placement xPC560S EVB User Manual RE micro www pemicro com EXTERNAL 5U OR 343 ON OFF o Go e e MPC56DxS COMPATIBLE afi A7 sl OF HEU N e 00 Og GA MINIMODULE O O O m2 E UH O a JTRG a o sO a wl de voorz O OO pO voor ussalO Ens En 3 55 Eds 291 PsUU HOOR 90000 mer BE oo Har C63 ME 240 00 EE E cial o oons TEST oon E BER jn SPC5605x COMPATIBLE unn pon bon O O EE J2 RST PULLUP 1 1 O pon B He OO v 5 a C l BODT CONFIGURATION mi OO O B O ln o 39 n a H Figure 2 4 xPC560SADPT208S Top Component Placement 2 2 Pin Numbering for Jumpers Jumpers for both th
35. or on the target By using the USB ML PPCNEXUS Interface the user can take advantage of the background debug mode to halt normal processor execution and use a PC to control the processor The user can then directly control the target s execution read write registers and memory values debug code on the processor and program internal or external FLASH memory devices The USB ML PPCNEXUS enables you to debug program and test your code on your board Software The USB ML PPCNEXUS Interface works with Codewarrior as well as P amp E s xPC560S EVB User Manual RE micro WWW pemicro com in circuit debugger and flash programmer to allow debug and flash programming of the target processor P amp E s USB ML PPCNEXUS Development Packages come with the USB ML PPCNEXUS Interface as well as flash programming software in circuit debugging software Windows IDE and register file editor 7 3 Working With P amp E s Cyclone MAX P amp E s Cyclone MAX 7 3 1 Product Features amp Implementation P amp E s Cyclone MAX is an extremely flexible tool designed for debugging testing and in circuit flash programming of Freescale s ColdFireV2 3 4 PowerPC 5xx 8xx 55xx 56xx and ARM7 microcontrollers The Cyclone MAX connects your target to the PC via USB Ethernet or Serial Port and enables you to debug your code program and test it on your board After development is complete the Cyclone MAX can be used as a production tool on your
36. rnal power supply input available on the Mini Module should NOT be used When the xPC5608 Mini Module is used as a stand alone board an external 5V or 3 3V power supply must be used Note that when using the xPC560S Mini Module as a stand alone board only one power supply is available 5V or 3 3V and all appropriate jumpers must be configured to use that power supply The following jumpers affect the power supply pins of the MPC560xS processor J4 VIO Voltage Selection Controls whether certain VO pins are powered using 5V or 3 3V In particular 40 xPC560S EVB User Manual RE micro WWW pemicro com this controls the voltage of the reset circuit and the logic high voltage for the FABM and ABSO pins Jumper Setting Effect 142 default VIO voltage is 5V 2 3 VIO voltage is 3 3V J14 5V MCU Power Enable Allows 5V to be selected for the various power pins on the MPC560xS processor Jumper Setting Effect 5V is available to power the various power supply On default pins on the MPC560xS processor Off 5V cannot be used to power any of the various power supply pins on the MPC560xS processor J15 1 2V Core Voltage Enable Controls whether power is provided to the VDD 1V2 pins on the MPC560xS processor Jumper Setting Effect MPC560xS VDD 1V2 pins are connected to 1 2V power On default xPC560S EVB User Manual 41 RE micro
37. rnet and Serial stand alone programming functionality high speed data transfer a status LCD and many other advanced capabilities Below is an overview of the features and intended use of the USB ML PPCNEXUS and Cyclone MAX 7 1 1 USB ML PPCNEXUS Key Features e Programming and debugging capabilities Compact and lightweight Communication via USB 2 0 e Supported by P amp E software and Freescale s CodeWarrior 7 1 2 Cyclone MAX Key Features Advanced programming and debugging capabilities including PC Controlled and User Controlled Stand Alone Operation xPC560S EVB User Manual 61 DE micro www pemicro com 7 2 7 2 1 7 2 2 62 Interactive Programming via Host PC n Circuit Debugging Programming and Testing Compatible with Freescale s ColdFireV2 3 4 PowerPC 5xx 8xx 55xx 56xx and ARM7 microcontroller families Communication via USB Serial and Ethernet Ports Multiple image storage LCD screen menu interface Supported by P amp E software and Freescale s CodeWarrior Working With P amp E s USB ML PPCNEXUS P amp E s USB ML PPCNEXUS Product Features amp Implementation P amp E s USB ML PPCNEXUS Interface USB ML PPCNEXUS connects your target to your PC and allows the PC access to the debug mode on Freescale s PowerPC 5xx 8xx 55xx 56xx microcontrollers It connects between a USB port on a Windows 2000 XP 2003 Vista machine and a standard 14 pin JTAG Nexus connect
38. ser Manual RE micro WWW pemicro com 243 MPC560xS VDD IO D is powered by 3 3V J18 must be ON J21 VDDMC Voltage Selection Sets the voltage level on the MPC560xS VDD SMD C power pin Jumper Setting Effect 142 default MPC560xS VDD_SMD_C is powered by 5V J14 must be ON 243 MPC560xS VDD SMD C is powered by 3 3V J18 must be ON J20 VDDMB Voltage Selection Sets the voltage level on the MPC560xS VDD SMD B power pin Jumper Setting Effect 142 default MPC560xS VDD_SMD_B is powered by 5V J14 must be ON 243 MPC560xS VDD_SMD_B is powered by 3 3V J18 must be ON xPC560S EVB User Manual 33 RE micro www pemicro com J19 VDDMA Voltage Selection Sets the voltage level on the MPC560xS VDD SMD A power pin Jumper Setting Effect MPC560xS VDD SMD A is powered by 5V J14 142 default must be ON MPC560xS VDD SMD A is powered by 3 3V J18 must be ON 243 J24 VDDE C Voltage Selection Sets the voltage level on the MPC560xS VDD IO F power pin Jumper Setting Effect MPC560xS VDD IO F is powered by 5V J14 must 1 2 default be ON e MPC560xS VDD IO F is powered by 3 3V J18 must be ON J23 VDDE B Voltage Selection Sets the voltage level on the MPC560xS VDD IO E power pin Jumper Setting
39. used Note that when using the xPC560S Mini Module as a stand alone board only one power supply is available 5V or 3 3V and all appropriate jumpers must be configured to use that power supply The following jumpers affect the power supply pins of the MPC560xS processor J4 VIO Voltage Selection Controls whether certain VO pins are powered using 5V or 3 3V In particular this controls the voltage of the reset circuit and the logic high voltage for the xPC560S EVB User Manual 51 RE micro www pemicro com FABM and ABSO pins Jumper Setting Effect 1 2 default VIO voltage is 5V 2 3 VIO voltage is 3 3V J14 5V MCU Power Enable Allows 5V to be selected for the various power pins on the MPC560xS processor Jumper Setting Effect 5V is available to power the various power supply On default pins on the MPC560xS processor 5V cannot be used to power any of the various power supply pins on the MPC560xS processor Off J15 1 2V Core Voltage Enable Controls whether power is provided to the VDD 1V2 pins on the MPC560xS processor Jumper Setting Effect MPC560xS VDD 1V2 pins are connected to 1 2V power On default Off MPC560xS VDD 1V2 pins are left disconnected 52 xPC560S EVB User Manual DE micro www pemicro com J17 Debug Port Voltage Configuration Sets the logic voltage level on the 14 p
40. wered by 5V J14 must be ON 243 MPC560xS VDD IO A is powered by 3 3V J18 must be ON J25 VDDE E Voltage Selection Sets the voltage level on the MPC560xS VDD IO D power pin Jumper Setting Effect xPC560S EVB User Manual RE micro www pemicro com 1 2 default MPC560xS VDD IO D is powered by 5V J14 must be ON 2 3 MPC560xS VDD IO D is powered by 3 3V J18 must be ON J21 VDDMC Voltage Selection Sets the voltage level on the MPC560xS VDD SMD C power pin Jumper Setting 142 default Effect MPC560xS VDD SMD C is powered by 5V J14 must be ON 243 MPC560xS VDD_SMD_C is powered by 3 3V J18 must be ON J20 VDDMB Voltage Selection Sets the voltage level on the MPC560xS VDD SMD B power pin Jumper Setting Effect 1 2 default MPC560xS VDD_SMD_B is powered by 5V J14 must be ON 243 MPC560xS VDD_SMD_B is powered by 3 3V J18 must be ON 44 xPC560S EVB User Manual DE micro www pemicro com J19 VDDMA Voltage Selection Sets the voltage level on the MPC560xS VDD SMD A power pin Jumper Setting Effect MPC560xS VDD_SMD_A is powered by 5V J14 142 default must be ON MPC560xS VDD SMD A is powered by 3 3V J18 must be ON 243 J24 VDDE C Voltage Selection Sets the voltage
41. y of the software and documentation for each user in the group Contact P amp E for volume discounts and site licensing agreements P amp E Microcomputer Systems does not assume any liability for the use of this software beyond the original purchase price of the software In no event will P amp E Microcomputer Systems be liable for additional damages including any lost profits lost savings or other incidental or consequential damages arising out of the use or inability to use these programs even if P amp E Microcomputer Systems has been advised of the possibility of such damage By using this software you accept the terms of this agreement 2008 P amp E Microcomputer Systems Inc MS DOS and Windows are registered trademarks of Microsoft Corporation Freescale and ColdFire are registered trademarks of Freescale Inc IBM and PowerPC are registered trademarks of IBM corporation P amp E Microcomputer Systems Inc P O Box 2044 Woburn MA 01888 617 923 0053 http www pemicro com Manual version 1 00 RE mcns 1 iz dn 1 1 1 Package Contents rage b tenderet et De dienes 2 1 2 Supported Devices ee ee ee ER ER EA AA ee ee ee eene en eren ee ee ee ee nn 2 1 3 Recommended Materials iese ee Ke AA ee Ge AK Ee DK Ge 2 1 4 Handling Precautlohs KERS obi dod ac bed eite Ee ko dee Ee Ee 3 2 HARDWARE FEATURES sse nennen nn ee nennen nnn 4 2 1 xPC560SADPT Mini Module Board Features
Download Pdf Manuals
Related Search