1/3” Day&Night Camera VKC-1392, VKC-1392/12-24
Contents
1. EXIT EXIT Exits the menu and does not save changes made 9 DC IRIS LENS The lens is not supplied with this camera Purchase a lens suitable for your requirements These cameras accept both C and CS mount type lens Notes gt For using main functions it is recommended to use Auto lris Lens with DC type If the lens is marked with fingerprints other marks the image quality might be poor It is recommended to use a high quality lens to improve the image quality under low illumination INSTALLING AUTO IRIS LENS 1 Remove the cover from the iris lens plug supplied and solder the lens cable to the plug as shown below e Video type e DCtype Pin 1 Red Power source Pin 1 Damping Pin 2 N C Pin 2 Damping Pin 3 White Video signal Pin 3 Drive Pin 4 Black GND Pin 4 Drive Rib Connector EF Automatic Pin3 cover vd Iris Lens Pin 1 Heat Pin4 Shrinkable Tubes Pin 2 Iris Control Cable Connector 2 Remove the protective cap and attach the lens to the camera by turning clockwise 10 SPECIFICATIONS MODEL NTSC PAL Free Power source DC 12V AC 24V 1096 100 240 50Hz Power Power consumption 3 5 Watts 300mA 4 0 Watts 55mA Image sensor 1 3 SONY EXview HAD CCD II Total pixels 1020 H x 508 V 1020 H x 596 V Effective pi2. 2 R dermark Germany Tel 49 0 6074 888 0 Fax 49 0 6074 888 100 www videor com www eneo security com Technical changes reserved Copyright by Videor E Hartig GmbH 09 2012
3. IRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES 003 CET APPAREIL NUMERIQUE DE LA CLASSE A EST CONFORME A LA NORME NMB 003 DU CANADA CE COMPLIANCE STATEMENT WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at pl
4. Operating Instructions 1 3 Day amp Night Camera VKC 1392 VKC 1392 12 24 gt N WARNINGS AND CAUTIONS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICABLE PARTS INSIDE REFFER SERVICING TO QUALIFIED SERVICE PERSONNEL EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product PRECAUTIONS Safety Installation Should any liquid or solid object fall into the cabinet Do not install the unit in an extremely hot or humid place unplug the unit and have it checked by or in a place subject to excessive dust mechanical qualified personnel before operating it any further vibration Unplug the unit from the wall outlet if it is not going to The unit is not designed to be waterproof
5. SE 1 Enables disables the motion detection AREA SEL 1 4 Selects the motion detection area Note Set the area sel it would be better BOTTOM and RIGHT BLOCK DISP OFF MONITOR AREA ON 1 O top AREA SEL 1 4 BOTTOM 0 244 TOP 000 244 bottom BOTTOM 076 LEFT 0 474 LEFT 000 O left RIGHT HI 8 RIGHT 0 474 RETURN 474 right PRIVACY AREA SEL 1 4 PRIVACY Selects the motion detection area AREA SEL 1 4 Note Set the area sel it would be better to move firstly BOTTOM and RIGHT i M LEFT BOTTOM 0 244 E nee 244 bottom TRANSP 1 00 MOSAIC OFF RETURN LEFT 0 474 O left RIGHT 0 474 474 right COLOUR 1 8 Sets the colours of the privacy zones TRANSP 0 00 0 50 0 75 1 00 Sets the transparency of the privacy zone area if colour is selected MOSAIC ON OFF Sets the mosaic function as the privacy to ON or OFF Note when ON transparency needs to be set at 0 00 and privacy zones can only be 1 colour OR mosaic and not mixed DAY NIGHT AUTO BURST ON OFF Allows the colour burst signal in monochrome to be removed if required DELAY CNT 0 255 secs Sets the hysteresis time before switching between colour mono amp mono colour to reduce the hunting effect DAY NIGHT 0 255 Sets the threshold for switching from day to night operation NIGHT gt DAY 0 255 Sets the threshold for switching from night to day operation COLOUR colour only op
6. be used for several days or more Exposure to rain or water may damage the unit To disconnect the cord pull it out by the plug Never pull the cord itself Cleaning 0 A Clean the unit with a slightly damp soft cloth Allow adequate air circulation to prevent internal heat Use a mild household detergent Never use strong build up Do not place the unit on soft surfaces rugs solvents such as thinner or benzine as they might carpets sofas etc or near materials curtains jamage the finish of the unit draperies that may block the ventilation holes Retain the original carton and packing materials for safe Height and vertical linearity controls located on the transport of this unit in the future rear panel are for special adjustments by qualified personnel only FCC COMPLIANCE STATEMENT INFORMATION TO THE USER THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQU
7. eration B W monochrome only operation BURST ON OFF Allows the colour burst signal in monochrome to be removed if required NR 2D DNR This is used to remove noise from the image in low light conditions when is applied NR MODE OFF Y C Y C Sets the 2D NR filter mode Y LEVEL 0 15 Sets the Y filter Luminance strength C LEVEL 0 15 Sets the C filter Chrominance strength CAMERA ID Sets the camera ID to ON or OFF A title of 26 characters per line can be applied CAMERA ID Use the joystick to navigate the cursor Pushing centrally on the joystick will allow selection of that character CAMERAID ABCDEFGH JKLMNOPQRSTUV WXYZ0123456789 4 8 O 20Y The arrows at the bottom CHRI 2 allow you to move the cursor 444 CLR POS RETURN without changing the character CHR1 Allows you to edit line 1 CHR2 Allows you to edit line 2 CHR2 is no using CLR Inserts a space POS Allows you adjust the location of the camera ID title display if you move too much right side or down it might lose ID on the screen SYNC Dual amp Free volt only INT This mode is necessary for using the internal synchronization LANGUAGE LANGUAGE select between English Japanese German French Russian Portuguese amp Spanish CAMERA RESET CAMERA RESET Returns the camera to the factory default settings SAVE ALL SAVE ALL Saves all the changes made in the menu
8. h USER 1 amp 2 can be individually set up for specific applications The gain values for the outdoor fixed mode are used as the adjustment items of USER1 on the internal OSD menu B GAIN 0 255 R GAIN 0 255 ANTI CR Colour rolling suppression MANUAL The B and R gain values for manual WB are set on this screen LEVEL 14 57 PUSH LOCK PUSHLOCK is selected and the Enter input is active BACKLIGHT Sharpens subjects with backlight OFF BLC HLC PICT ADJUST MIRROR ON OFF Horizontally inverts image BRIGHTNESS 07255 Sets the screen brightness CONTRAST 07255 Sets the screen contrast SHARPNESS 07255 Sets the screen sharpness HUE 07255 Adjusts the hue GAIN 07255 Adjusts the gain ATR ATR Adaptive Tone Reproduction allows adjustment of the image to assist with widely contrasting scenes of view LUMINANCE LOW MID HIGH Sets the extent of the luminance compression CONTRAST LOW MIDLOW MID MIDHIGH HIGH Sets the extent of the contrast enhancement MOTION DET DETECT SENSE 0 127 Sets the motion detection sensitivity O low sensitivity 127 high sensitivity BLOCK DISP OFF ON ENABLE Applies a Motion block trace in the selected area To define the area select Enable and push centrally on the joystick Use the Joystick to navigate to the blocks you want to Disable and not include in motion trace To return to the menu push and hold central joystick for 2secs and release MOTION AREA ON OFF DETECT SEN
9. lts PORTUGUESE SPANISH LENS MANUAL Manual lens only Note Since Manual mode AUTO mode is changed SHUTTER AGC to SHUT AUTO IRIS when MANUAL is changed to AUTO AUTO MODE should be changed to AUTO IRIS in SHUTTER AGC AUTO TYPE DC VIDEO Sets the type of mechanical iris MODE OPEN CLOSE AUTO Sets the type of control to be applied over the mechanical iris SPEED 0 255 Sets the convergence speed of the mechanical iris SHUTTER AGC AUTO HIGH LUMINANCE MODE SHUT SHUT AUTO IRIS Note only SHUT can be selected if LENS is in MANUAL mode SHUT AUTO IRIS is AE Auto Exposure for SHUTTER And MIRIS is open BRIGHTNESS 0 255 Adjusts the brightness LOW LUMINANCE MODE AGC OFF Auto Gain Control on or off BRIGHTNESS x0 25 x0 50 x0 75 x1 00 Amount of AGC applied in low lighting conditions MANUAL MODE SHUT OFF Auto gain control SHUTTER Select the shutter speed 1 50 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 AGC Sets the AGC gain applied dB for ME manual exposure 6 12 18 24 30 36 42 44 8dB WHITE BAL ATW Auto Trace White balance SPEED 0 255 Adjusts the pull in speed of ATW DELAY CNT 0 255 Sets the time based hysteresis of ATW ATW FRAME X0 5 X1 X1 5 X2 Sets the pull in frame magnification ENVIROMENT indoor outdoor Preset for either indoor or outdoor applications of the ATW PUSH Wide range Auto White Balance mode AWB USER1 amp 2 Bot
10. onnector for video or dc type auto iris lens 3 CS adapter ring for C mounting C lenses 4 This manual TABLE CONTENTS INTRODUCTION 1 COMERA OVERVIEW nn 2 OSD MENU STRUCTURE 3 DC IRIS LENS 10 SPECIFICATIONS 11 vi INTRODUCTION The camera provides high quality images using SONY 1 3 CCD and digital Signal process LSIS Features 1 3 EXview HAD CCD II for an image of high sensitivity Digital Wide Dynamic Range Xtended Dynamic Range Excellent picture quality 700 lines of resolution 0 15Lux Color 0 01Lux B W F1 2 Sensitivity Auto electronic shutter 1 60 1 50 1 10 000 and manual electronic shutter modes OSD On Screen Display Auto and manual white balance modes Auto BLC and HLC Day amp Night Auto Manual Privacy Zone 4 areas Motion Detection 4 areas MIRROR SHARPNESS HUE CONTRAST GAIN AGC Auto Gain Control VIDEO OUT BNC Internal Quick connect for DC lens with 4 pin connector Operates in 12VDC or 24VAC Operates in 100 240VAC Use Certified Listed Class 2 power source only If using DC 12V power adaptor Please use a power supply capable of supplying over 600mA IMPORTANT The user of thi
11. s camera is responsible for checking and complying with local state and federal laws and statutes concerning the recording and monitoring of audio signals CAMERA OVERVIEW TOP VIEW SIDE VIEW FRONT VIEW Left Button Up Button Enter Button Right Button Down Button External Day Night O Motion ALARM OUT RS 485 O Power Indicator Video Output Connector BNC AC DC Compatible Input Terminal AC Power Cord 000000 REAR VIEW OSD MENU STRUCTURE SETUP MENU page 1 LENS LENS SHUTTER AGC WHITE BAL AUTO IRIS BACKLIGHT MANUAL PICT ADJUST ATR MOTION DET RETURN NEXT page2 EXIT SAVE ALL WHITE BALANCE ATW PUSH USER 1 USER 2 ANTI CR MANUAL PUSH LOCK RETURN PICTURE ADJUST ATR MIRROR LUMINANCE BRIGHTNESS CONTRAST CONTRAST SHARPNESS HUE GAIN RETURN RETURN SHUTTER AGC AUTO MANUAL RETURN BACKLIGHT BLC HLC RETURN MOTION DET DETECT SENSE BLOCK DISP MONITOR AREA AREA SELECT RETURN SETUP MENU page 2 PRIVACY PRIVACY DAY NIGHT DAY NIGHT NR AREA SEL AUTO CAMERA ID COLOUR COLOUR SYNC TRANSP B W LANGUAGE MOSAIC CAMERA RESET BACK page 1 EXIT SAVE ALL RETURN RETURN NR CAMERA ID NR MODE titling Y LEVEL C LEVEL RETURN RETURN RETURN LANGUAGE CAMERA RESET ENGLISH CHINESE return the GERMAN camera to FRENCH factory RUSSIAN defau
12. ugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been moisture does not operate normally or has been dropped 15 CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO 16 Use satisfy clause 2 5 of IEC60950 1 UL60950 1 or Certified Listed Class 2 power source only NOR gt CONTENTS OF PACKAGE Installation of the camera must be performed by qualified service personnel in accordance with all local and national electrical and mechanical codes Carefully remove the color camera and its accessories from the carton and verify that they were not damaged in shipment The contents of the package includes 1 Color CCD camera 2 Mini DIN c
13. xels 976 H x494 V 976 H x582 V Scanning system 2 1 Interlace Scanning frequency 19 15 625KHz H x 50Hz V x 59 94Hz V Sync system Internal Electronic Shutter 1 50 1 10 000 sec Resolution TOOTVL Min illumination 0 15lux Video output 1 0Vp p 75 ohm composite SIN ratio 50dB OFF Camera Control Internal OSD Key LUMINANCE L M H CONTRAST L LM M MH H eproduction Backlight OFF BLC HLC F Day amp Night Digital D N Color BW Auto U MD Motion Detection On 4 areas Off Adjustable Size 8 Sensitivity PM Privacy Masking 0 4 zone C WB White Balance ATW PUSH USER1 USER2 ANYICR MANUAL PUSH LOCK AGC Auto Gain Control On Off T Exposure Auto Iris Auto Iris Electronic Shutter Brightness 0 255 steps O Contrast 0 255 steps N Sharpness 0 255 steps HUE 0 255 steps Gain 0 255 steps NR Noise Reduction OFF Y C Y C Mirror ON OFF Power input 2 pin terminal block Power Cord Video output BNC connector Auto iris output 4 Pin Mini Din jack standard connection 2 Lens Mount C CS Mount Selected through back focus 5 Operating temperature 10 C 50 C 2 Operating humidity 0 96 non condensing External dimension 66 W x 56 H x 120 D mm Weight 240g 440g 11 MEMO eneo eneo is a registered trademark of Videor E Hartig GmbH Exclusive distribution through specialised trade channels only Videor E Hartig GmbH Carl Zeiss Strafte 8 6332
Download Pdf Manuals
Related Search