WAP1750 Quick Installation Guide
Contents
1. 1 Press and hold the WPS Reset button on the side of the access point for 2 seconds 2 Within two minutes activate WPS on your WPS compatible wireless device Please check the documentation for your wireless device for information regarding its WPS function 3 The devices will establish a connection 10 lll Edimax Pro NMS Edimax Pro Network Management Suite NMS supports the central management of a group of access points otherwise known as an AP Array NMS can be installed on one access point and support up to 8 Edimax Pro access points with no additional wireless controller required reducing costs and facilitating efficient remote AP management Edimax Pro NMS is simple to setup An overview of the system is shown below XDSL or AC Gateway UTM Gateway Cable Modem Em GEB Internet POE switch Edimax Pro NMS uui J J e Layer 2 Environment PA One AP access point is designated as the AP Controller master and other connected Edimax Pro APs are automatically designated as Managed APs slaves Using Edimax Pro NMS you can monitor configure and manage all Managed APs up to 8 from the single AP Controller 11 A Ensure you have the latest firmware from the Edimax website for your Edimax Pro products 1 Connect all APs to an Ethernet or PoE switch which is connected to a gateway router A You can use your router as a DHCP server or you can later2. configure your AP Controller as a DHCP server p Router PoE Switch I ll i 2 Ensure all APs are powered on and check LEDs 12 3 Designate one AP as the AP Controller which will manage all other connected APs up to 8 AP Controller PoE Switch 4 Connect a computer to the designated AP Controller using an Ethernet cable PoE Switch XDiMAX P xDimAx p mimax P mom vnm 13 5 Open a web browser and enter the AP Controller s IP address in the address field The default IP address is 192 168 2 2 1N Your computer s IP address must be in the same subnet as the AP a Controller Refer to the user manual for more help OU mium Tre met Dems rerum d CDD e ere FTOTOCOI Verzion amp P sieve rropenries Gener al fou can get IP settings asaqned automaticaly if your network supports this capabe ty Otherwise you need to ask your network admmst tor for the appropriate IP settings Obtan an IP address automaticaly Use the folowing IP address P address 192 168 Subnet mask 255 255 255 0 Default gateway Ve Use the following ONS server addresses Preferred ONS serwer Alternate ONS server a Ifyou changed the AP Controller s IP address or if your A gateway router uses a DHCP server ensure you enter the correct IP address Refer to your gateway router s settings 6 Enter the username amp password to login The default username amp
3. password are admin amp 1234 J You will arrive at the Edimax Pro NMS Dashboard Go to Management gt Operation Mode and select AP Controller Mode from the drop down menu 14 15 EDIMAX Q Home Logout Global English LE SIE EU Information Network Settings Wireless Settings Management Operation Mode 1 gt Admin Operation Mode Date and Time gt Syslog Server Operation Mode Managed AP mode Y AP Mode Di AP Controller Mode ee n Managed AP mode Apply Cancel gt I m Here gt NMS Settings 8 Click Apply to save the settings Operation Mode Operation Mode AP Controller Mode T gt Apply Cancel 9 Edimax Pro NMS includes a wizard to quickly setup the SSID amp security for Managed APs Click Wizard in the top right corner to begin mie iaa Home Logout Global 10 Follow the instructions on screen to complete Steps 1 2 amp 3 and click Finish to save the settings nai sh Y Step 2 AP Discovery Step 3 Setup WLAN Step 1 Welcome gt St JiscoV aged AP s Match whole words start please power on the managed APs and plug into the same et network with this AP Controller AC Address Device Name Model IP Address Status Z 74DA 38 03 B5 30 APT4DA3803B530 WAP1750 192 168 222 222 Q This Setup W izard will guide you through a basic procedure to 4 T4DA38 00 00 B4 AP74DA380000B4 WAP17
4. EY 2011 65 EY oleelliset vaatimukset ja muut asiaankuuluvat m r ykset OO00000900000o0 C OF AH D O OOOO OOO d e WEEE Directive amp Product Disposal E At the end of its serviceable life this product should not be treated as household or general waste It should be handed over to the applicable collection point for the recycling of electrical and electronic E equipment or returned to the supplier for disposal 20 Declaration of Conformity We Edimax Technology Co Ltd declare under our sole responsibility that the equipment described below complies with the requirements of the European R amp TTE directives Equipment AC1750 Wall Mount Access Point Model No WAP1750 The following European standards for essential requirements have been followed Directives 1999 5 EC Spectrum ETSI EN 300 328 V1 8 1 2012 06 EMC EN 301 489 1 V1 9 2 2011 09 EN301 489 17 V2 2 1 012 09 EN 301 893 V1 7 1 2012 06 Safety LVD IEC 60950 1 2005 2 Edition Am 1 2009 EN 60950 1 2006 A11 A 2010 A12 2011 Recommendation19 99 5 EC EMF EN 62311 2008 Directives 2006 95 EC Safety LVD EC 60950 1 2005 2 Edition Am 1 2009 EN 60950 1 2006 A11 A 2010 A12 201 1 Edimax Technology Co Ltd No 3 Wu Chuan 3 Road Wu Ku Industrial Park New Taipei City Taiwan Date of Signature Jan 2015 CEO v Printed Name Albert Chang Title Director Edimax Technology Co Ltd 21 Notice According
5. covered by this License they are outside its scope The act of running the Program is not restricted and the output from the Program is covered only if its contents constitute a work based on the Program independent of having been made by running the Program Whether that is true depends on what the Program does 22 1 You may copy and distribute verbatim copies of the Program s source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and give any other recipients of the Program a copy of this License along with the Program You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee 2 You may modify your copy or copies of the Program or any portion of it thus forming a work based on the Program and copy and distribute such modifications or work under the terms of Section 1 above provided that you also meet all of these conditions a You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change b You must cause any work that you distribute or publish that in whole or in part contains or is derived from the Program or any part thereof to be licensed as a whole at no charge to all third pa
6. to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2 The program is free software and distributed without any warranty of the author We offer valid for at least three years to give you for a charge no more than the costs of physically performing source distribution a complete machine readable copy of the corresponding source code Das Produkt beinhaltet Software die den Bedingungen der GNU GPL Version 2 unterliegt Das Programm ist eine sog Free Software der Autor stellt das Programm ohne irgendeine Gewahrleistungen zur Verf gung Wir bieten Ihnen fur einen Zeitraum von drei Jahren an eine vollst ndige maschinenlesbare Kopie des Quelltextes der Programme zur Verf gung zu stellen zu nicht h heren Kosten als denen die durch den physikalischen Kopiervorgang anfallen GNU GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1989 1991 Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed Preamble The licenses for most software are designed to take away your freedom to share and change it By contrast the GNU General Public License is intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This General Public License applies to m
7. 50 19216822222 configure NMS system 74 DA 38 00 20 40 WAP1750 Q Next gt gt Cancel Rescan Next gt gt Cancel Step 1 Welcome Step 2 AP Discovery l SSID PASSWORD Guest Network Enable Disable Guest SSID Security Key SGHz Settings Clone 2 4GHz Settings SSID SSID Security Key PASSWORD Guest Network Enable Disable Guest SSID A If any of your Managed APs are not found during Step 2 AP Discovery reset the Managed AP to its factory default settings Refer to the user manual for help 11 Your Controller AP amp Managed APs should be fully functional Use the top menu to navigate around Edimax Pro NMS EDIMAX Z7 WAP1750 Dashboard Zone Plan NMS Monitor NMS Settings Local Network Local Settings Toolbox Use Dashboard Zone Plan NMS Monitor amp NMS Settings to configure Managed APs Use Local Network amp Local Settings to configure your Controller AP A Refer to the user manual for more information 16 IV Hardware Installation ll 1 Router PoE Switch 1 Connect a router or PoE switch to the access point s LAN 1 port using an Ethernet cable PoE switches must be connected to the access point s LAN 1 port Router PoE Switch 2 if you are using a router then connect the power adapter to the access point s 12V DC port and plug the power adapter into a power supply 3 if you are using a PoE Power over Ethernet switch then it is no
8. AP Controller master in an AP array refer to IIl Edimax Pro NMS Il 2 AP Mode Basic Settings The instructions below will help you to configure the following basic settings of the access point LAN IP Address 2 4GHz amp 5GHz SSID amp Security Administrator Name amp Password Time amp Date A It is recommended you configure these settings before using the access point 1 To change the access point s LAN IP address go to Network Settings gt LAN side IP Address and you will see the screen below LAN side IP Address IP Address Assignment DHCP Client IP Address 192 168 2 2 Subnet Mask 255 255 255 Default Gateway From DHCP Y Primary DONS Address From DHCP v 0 0 0 0 Secondary DNS Address From DHCP v 0 0 0 0 2 Enter the IP address settings you wish to use for your access point You can use a dynamic DHCP or static IP address depending on your network environment Click Apply to save the changes and wait a few moments for the access point to reload A When you change your access point s IP address you need to use AP the new IP address to access the browser based configuration interface instead of the default IP 192 168 2 2 3 To change the SSID of your access point s 2 4GHz wireless network s go to Wireless Setting 2 4GHz 11bgn Basic Enter the new SSID for your 2 4GHz wireless network in the SSID1 field and click Apply A To utilize multip
9. BN 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC Sloven ina Toto zariadenie sp a z kladn po iadavky a al ie pr slu n ustanovenia smern c 1995 5 ES 2009 125 ES 2006 95 ES 2011 65 ES Deutsch Dieses Ger t erf llt die Voraussetzungen gem den Richtlinien 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC Espa ol El presente equipo cumple los requisitos esenciales de la Directiva 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC Italiano Questo apparecchio conforme ai requisiti essenziali e alle altre disposizioni applicabili della Direttiva 1995 5 CE 2009 125 CE 2006 95 CE 2011 65 CE Nederlands Dit apparaat voldoet aan de essenti le eisen en andere van toepassing zijnde bepalingen van richtlijn 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC Portugu s Este equipamento cumpre os requesitos ess nciais da Directiva 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC Norsk Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC Svenska Denna utrustning r i verensst mmelse med de v sentliga kraven och vriga relevanta best mmelser i direktiv 1995 5 EG 2009 125 EG 2006 95 EG 2011 65 EG Dansk Dette udstyr er i overensstemmelse med de v sentligste krav og andre relevante forordninger i direktiv 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC suomen kieli T m laite t ytt direktiivien 1995 5 EY 2009 125 EY 2006 95
10. EDIMAX NETWORKING PEOPLE TOGETHER WAP1750 Quick Installation Guide 04 2015 v1 1 Edimax Technology Co Ltd No 3 Wu Chuan 3rd Road Wu Gu New Taipei City 24891 Taiwan Email support edimax com tw Edimax Technology Europe B V Fijenhof 2 5652 AE Eindhoven The Netherlands Email support Qedimax nl Edimax Computer Company 3350 Scott Blvd Bldg 15 Santa Clara CA 95054 USA Live Tech Support 1 800 652 6776 Email support edimax com Product Information l 1 Package Contents O 7 8 1 WAP1750 Access Point 2 Antennas x 3 3 Magnetic Wall Mount x 2 amp Screws 4 CD X3 p AA d A XX o7 A b e D Quick Installation Guide 6 Ethernet Cable 7 Power Adapter 8 Magnetic Wall Mount Screw Template l 2 System Requirements Existing cable DSL modem amp router Computer with web browser for access point configuration l 3 Hardware Overview A 12V DC IN C LAN 2 E Eject G Reset On Off B LAN 1 PoE D USB Port F Console H WPS 12V DC port to connect the power adapter LAN port with Power over Ethernet PoE IN LAN port with Power over Ethernet PoE OUT USB Port for system log and save restore settings Eject an attached USB device Connect a management console Reset the access point to factory default settings Wi Fi Protected Setup WPS button Switch the access point on off ro mmonw Sd l 4 LED Status LED Status The access po
11. Foundation may publish revised and or new versions of the General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Program specifies a version number of this License which applies to it and any later version you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation If the Program does not specify a version number of this License you may choose any version ever published by the Free Software Foundation 10 If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different write to the author to ask for permission For software which is copyrighted by the Free Software Foundation write to the Free Software Foundation we sometimes make exceptions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally NO WARRANTY 11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE PROGRAM TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR I
12. MPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAM PROVE DEFECTIVE YOU ASSUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 12 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE BE LIABLE TO YOU FOR DAMAGES INCLUDING ANY GENERAL SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 24 DIMAX NETWORKING PEOPLE TOGETHER
13. ands that there is no warranty for this free software If the software is modified by someone else and passed on we want its recipients to know that what they have is not the original so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses in effect making the program proprietary To prevent this we have made it clear that any patent must be licensed for everyone s free use or not licensed at all The precise terms and conditions for copying distribution and modification follow TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION 0 This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License The Program below refers to any such program or work and a work based on the Program means either the Program or any derivative work under copyright law that is to say a work containing the Program or a portion of it either verbatim or with modifications and or translated into another language Hereinafter translation is included without limitation in the term modification Each licensee is addressed as you Activities other than copying distribution and modification are not
14. collective works based on the Program In addition mere aggregation of another work not based on the Program with the Program or with a work based on the Program on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may copy and distribute the Program or a work based on it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following a Accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or b Accompany it with a written offer valid for atleast three years to give any third party for a charge no more than your cost of physically performing source distribution a complete machine readable copy of the corresponding source code to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or c Accompany it with the information you received as to the offer to distribute corresponding source code This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer in accord with Subsection b above The source code for a work means the preferred form of the work for making modifications to it For an executable work compl
15. ely from distribution of the Program If any portion of this section is held invalid or unenforceable under any particular circumstance the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances Itis not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system it is up to the author donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 8 If the distribution and or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the limitation as if written in the body of this License 9 The Free Software
16. ete source code means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the executable However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and so on of the operating system on which the executable runs unless that component itself accompanies the executable If distribution of executable or object code is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place counts as distribution of the source code even though third parties are not compelled to copy the source along with the object code 4 You may not copy modify sublicense or distribute the Program except as expressly provided under this License Any attempt otherwise to copy modify sublicense or distribute the Program is void and will automatically terminate your rights under this License However parties who have received copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 23 5 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Program or its derivative works These actions are pro
17. hibited by law if you do not accept this License Therefore by modifying or distributing the Program or any work based on the Program you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Program or works based on it 6 Each time you redistribute the Program or any work based on the Program the recipient automatically receives a license from the original licensor to copy distribute or modify the Program subject to these terms and conditions You may not impose any further restrictions on the recipients exercise of the rights granted herein You are not responsible for enforcing compliance by third parties to this License 7 If as a consequence of a court judgment or allegation of patent infringement or for any other reason not limited to patent issues conditions are imposed on you whether by court order agreement or otherwise that contradict the conditions of this License they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations then as a consequence you may not distribute the Program at all For example if a patent license would not permit royalty free redistribution of the Program by all those who receive copies directly or indirectly through you then the only way you could satisfy both it and this License would be to refrain entir
18. horized This transmitter is restricted for use with the specific antenna tested in the application for certification The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter R amp TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999 5 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity R amp TTE The R amp TTE Directive repeals and replaces in the directive 98 13 EEC Telecommunications Terminal Equipment and Satellite Earth Station Equipment As of April 8 2000 Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria Belgium Bulgaria Cyprus Czech Denmark Estonia Finland France Germany Greece Hungary Ireland Italy Latvia Lithuania Luxembourg Malta Netherlands Poland Portugal Romania Slovakia Slovenia Spain Sweden Turkey and United Kingdom The ETSI version of this device i
19. int is off The access point is starting up NM The access point is on l 5 Reset If you experience problems with your access point you can reset the device back to its factory settings This resets all settings back to default 1 Press and hold the reset button on the access point for at least 10 seconds than release the button You may need to use a pin or similar sharp object to push the am reset button 2 Wait for the access point to restart The access point is ready for setup when the LED is blue Il Quick Setup Your access point can be up and running in just a few minutes It can function as a standalone access point AP mode or as part of an AP array Managed AP mode or AP Controller mode This quick installation guide will help to set up your access point and configure its basic settings Il 1 Initial Setup 1 Connect the access point to a computer via Ethernet cable 2 Connect the power adapter to the access point s 12V DC port and plug the power adapter into a power supply using the included cable 3 Please wait a moment for the access point to start up The access point is ready when the LED is blue 4 Set your computer s IP address to 192 168 2 x where x is a number in the range 3 100 If you are unsure how to do this please refer to the user manual for more information A Please ensure there are no other active network connections on your computer disconnect Wi Fi c
20. le 2 4GHz SSIDs open the drop down menu labelled Enable SSID number and select how many SSIDs you require Then enter a new SSID in the corresponding numbered fields below before clicking Apply 2 4GHz Basic Settings Wireless Enable Disable Band 1ib g n v Enable 881D number v 8 SID1 WAP1750 EBGD56E G VLAN ID 1 Auto Channel Enable Disable Auto Channel Range Ch1 11 v One day Y Change channel even if clients are connected Auto Channel Interval Channel Bandwidth Auto Y BSS BasicRate Set 1 2 5 5 11 Mbps Y 4 To configure the security of your access point s 2 4GHz wireless network s go to Wireless Setting gt 2 4GHz 11bgn gt Security Select an Authentication Method and enter a Pre shared Key or Encryption Key depending on your choice then click Apply A If using multiple SSIDs specify which SSID to configure using the amp SSID drop down menu 2 4GHz Wireless Security Settings SSID WAP1750 F1965A_G w Broadcast SSID Enable w Wireless Client Isolation Disable w l Load Balancing Authentication Method No Authentication w Additional Authentication No additional authentication V D Go to Wireless Settings the access point s 5GHz wireless network Ui G L N IE IE QD e EA IE QU gt Q gt oE D O D Q ct Un ct D cO Uo UJ go I O s 6 To change the administrator name and password for the browser based co
21. nd to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes The product you have purchased and the setup screen may appear slightly different from those shown in this QIG The software and specifications are subject to change without notice Please visit our website www edimax com for updates All brand and product names mentioned in this manual are trademarks and or registered trademarks of their respective holders 18 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipmen
22. nfiguration interface go to Management gt Admin Account to Manage This Device Administrator Password 7 Complete the Administrator Name and Administrator Password fields and click Apply 8 To set the correct time for your access point go to Management Date and Time Date and Time Settings 2012 Year Jan x Month 1 Day 0 x Hours 00 x Minutes 00 x Seconds Local Time Acquire Current Time from Your PC Use NTP F Enable Server Name Update Interval hours Time Zone Time Zone GMT Greenwich Mean Time Dublin Edinburgh Lisbon London x O setthe correct time and time zone for your access point using the drop down menus The access point also supports NTP Network Time Protocol so alternatively you can enter the host name or IP address of a time server Click Apply when you are finished i You can use the Acquire Current Time from your PC button if a you wish to set the access point to the same time as your PC 10 The basic settings of your access point are now configured Please refer to IV Hardware Installation for guidance on connecting your access point to a router or PoE switch Il 3 Wi Fi Protected Setup WPS Wi Fi Protected Setup is a simple way to establish connections between WPS compatible devices You can use the WPS button to establish a connection between the access point and a WPS compatible wireless device client
23. onnections and Ethernet cables i D Enter the access points default IP address 192 168 2 2 into the URL bar of a web browser 6 You will be prompted for a username and password Enter the default username admin and the default password 1234 Connect to 192 168 2 2 The server 192 168 2 2 at localhost requires a username and password User name 2 admin Password ecccc Remember my password Cc Comas 7 You will arrive the System Information screen shown below e EDIMAX 275 Home Logout Global English v WAP1750 information Network Settings Wireless Settings Management Advanced Wireless Clients gt Wireless Monitor iie kiss le Product Name AP801F02E6D56E gt Log Uptime 0 day 00 02 14 Boot from Internal memory Version 1 1 7 MAC Address 803F 02 E6 D5 6E Management VLAN ID 1 IP Address 192 168 2 2 Refresh Default Gateway DNS DHCP Server Wired LAN Fort Settings Wired LAN Fort Status VLAN Mode ID Wired Port 1 Connected 1000 Mbps Full Duplex Untagged Port 1 Wired Port 2 Disconnected Untagged Port 1 8 Please follow the instructions below in II 2 Basic Settings to configure the access point s basic settings for use as a standalone AP in AP mode For use a Managed AP in an AP array the access point will automatically switch mode when an AP Controller is configured as described in IIl Edimax Pro NMS To use the AP as an
24. ost of the Free Software Foundation s software and to any other program whose authors commit to using it Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead You can apply it to your programs too When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software or use pieces of it in new free programs and that you know you can do these things To protect your rights we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it For example if you distribute copies of such a program whether gratis or for a fee you must give the recipients all the rights that you have You must make sure that they too receive or can get the source code And you must show them these terms so they know their rights We protect your rights with two steps 1 copyright the software and 2 offer you this license which gives you legal permission to copy distribute and or modify the software Also for each author s protection and ours we want to make certain that everyone underst
25. rties under the terms of this License c Ifthe modified program normally reads commands interactively when run you must cause it when started running for such interactive use in the most ordinary way to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty or else saying that you provide a warranty and that users may redistribute the program under these conditions and telling the user how to view a copy of this License Exception if the Program itself is interactive but does not normally print such an announcement your work based on the Program is not required to print an announcement These requirements apply to the modified work as a whole If identifiable sections of that work are not derived from the Program and can be reasonably considered independent and separate works in themselves then this License and its terms do not apply to those sections when you distribute them as separate works But when you distribute the same sections as part of a whole which is a work based on the Program the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or
26. s also authorized for use in EFTA member states Iceland Liechtenstein Norway and Switzerland EU Countries Not Intended for Use None 19 EU Declaration of Conformity English This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC Francais Cet quipement est conforme aux exigences essentielles et autres dispositions de la directive 1995 5 CE 2009 125 CE 2006 95 CE 2011 65 CE e tina Toto za zen je v souladu se z kladn mi po adavky a ostatn mi p slu n mi ustanoven mi sm rnic 1995 5 ES 2009 125 ES 2006 95 ES 2011 65 ES Polski Urz dzenie jest zgodne z og lnymi wymaganiami oraz szczeg lnymi warunkami okre lonymi Dyrektywa UE 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC Rom n Acest echipament este in conformitate cu cerin ele esen iale si alte prevederi relevante ale Directivei 1995 5 CE 2009 125 CE 2006 95 CE 2011 65 CE PycckHA 3TO o60pyanoBaHMe COOTBeTCTByeT OCHOBHbIM Tpe60BaHM8aM M nonoxeHnam AnpekTnBbi 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC Magyar Ez a berendez s megfelel az alapvet k vetelm nyeknek s m s vonatkoz ir nyelveknek 1995 5 EK 2009 125 EK 2006 95 EK 2011 65 EK Turkce Bu cihaz 1995 5 EC 2009 125 EC 2006 95 EC 2011 65 EC direktifleri zorunlu istekler ve diger h k mlerle ile uyumludur VkpaiHcbKa O6nanHaHHa BinnoBinae BAMOraM i yMoBaM ANpeKTu
27. t into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help FCC Caution This device and its antenna must not be co located or operating in conjunction with any other antenna or transmitter This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment Federal Communications Commission FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 2 5cm 1 inch during normal operation Federal Communications Commission FCC RF Exposure Requirements SAR compliance has been established in the laptop computer s configurations with PCMCIA slot on the side near the center as tested in the application for certification and can be used in laptop computer s with substantially similar physical dimensions construction and electrical and RF characteristics Use in other devices such as PDAs or lap pads is not aut
28. t necessary to use the included power adapter the access point will be powered by the PoE switch A Do not use the power adapter if you are using a PoE switch PoE Switch PoE Switch 4 Connect a local network client or switch to the access point s LAN 2 port as required A The access point s LAN 2 port can support another powered device PD 17 EDIMAX NETWORKING PEOPLE TOGETHER COPYRIGHT Copyright Edimax Technology Co Ltd all rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission from Edimax Technology Co Ltd Edimax Technology Co Ltd makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Any software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not this company its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software Edimax Technology Co Ltd reserves the right to revise this publication a
Download Pdf Manuals
Related Search