OPERATION MANUAL
Contents
1. HI Surveillance in low light environments Useful in the AGC VA 2 AGC HI LO position using amp GAIN CONTROL on the back panel LO O When a clear picture is required in standard lighting conditions When the object monitored on the screen disappears due to being ON illuminated brightly from behind useful in the AGC position 3 AGC B L by using GAIN CONTROL on the back panel OFF Normally used in this position V Effective at EI position by operation of 11 EI rotary switch when ON the object monitored on the screen appears black due to being 4 EI B L illuminated from behind OFF Normally used in this position Va 10 When external synchronization is required insert the synchronization signal jack into the SYNC IN BNC terminal The signal required for input is C SYNC or C Video using 0 2 to 4Vp p The input resistance of the WAT 535EX is 10K Q but when 75Q is required the external synchronization signal cable must be terminated to earth In this case the input voltage is the same as the above The WAT 535EX is set at internal synchronization When a synchronized signal is received by the camera it will adjust automatically to external synchronization SPECIFICATIONS Model No WAT 535EX EIA WAT 535EX CCIR CCD 1 3 inch Interline transfer CCD image sensor Number of total pixels 811 H x 5082. Water copcamera WAT 535EX OPERATION MANUAL Thank you for choosing our WAT 535EX CCD camera Watec hopes that both the quality and design satisfy your requirements Before proceeding to install or operate the WAT 535EX please read the contents of the Operation Manual thoroughly to ensure proper usage and understanding of our product For future reference we also advise safe keeping of this manual CAUTIONS Use only the AD 901 or equivalent power adaptor for the WAT 535EX Power supplied without voltage stabilization and or voltage range maintained at 10 12V DC may cause damage Do not expose the WAT 535EX to wetness or high moisture conditions The WAT 535EX is designed and approved for indoor use only For outdoor use or outdoor like conditions we recommend that a special camera housing is installed for adequate protection N m Avoid striking the unit with hard objects or dropping the unit Do not disassemble and or modify the WAT 535EX or its component parts or accessories Watec can not be held responsible for equipment operation failure or any damage and or trouble caused by such action wn Do not install the WAT 535EX near heat sources such as radiators or heating air ducts or in a place subject to direct sunlight X excessive dust mechanical vibration or shock an When installing the WAT 535EX in an industrial or commercial environment i e within equipment housing near other electronic devi
3. V 795 H x 596 V Number of effective pixels 768 H x 494 V 752 H x 582 V Unit cell size 6 35um H x 7 40um V 6 50um H x 6 25um V Scanning system 2 1 interlace Sync System Internal External External sync System C Sync C Video External sync Signal Signal 0 29 4 0Vp p Video output Composite Video 1Vp p 75Q Unbalanced Resolution 550TV lines center Minimum illumination 0 003 Ix F1 4 AGC 32dB Gamma characteristic 0 45 OFF AGC ON HI 50 32dB AGC LO 50 20dB AGC OFF 50 32dB Manual Back light AGC ON OFF compensation El ON OFF S N ratio 50dB GAIN 5dB Auto iris DC VIDEO AE El 1 60sec 1 100000sec 1 50sec 1 100000sec ES 1 250sec 1 500sec 1 1000sec 1 2000sec 1 5000sec 1 10000sec 1 100000sec FL 1 100sec 1 120sec OFF 1 60sec 1 50sec Lens mount CS mount Power supply DCO 10 89 13 2V 12V 100 Current Max 150mA Storage temperature 10 0 40 C Operating temperature 30 C 0 70 C Dimensions 44mm W x 43 5mm H x 53mm D Weight Approx 130g This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Important The camera mentioned above does not comply with this regulation if it is modified at your disposal Design and
4. TE Ensure that the power to the WAT 535EX and the monitor are set to OFF before making any connections 1 Remove the lens mount cap from the WAT 535EX and attach the lens Use the optional C mount adaptor 34CMA R when a C mount model lens is used NOTE Confirm the specifications of the lens being used when it can not be mounted onto the WAT 535EX smoothly 2 Connect the iris control cable to Auto iris on the WAT 535EX when an Auto iris lens is being used NOTE Confirm the version of the Auto iris lens to be used as shown below 1 Video iris lens 2 DC driven iris lens NOTE RG 58 U or RG 6 U coaxial cable with 75Q impedance must be used with the WAT 535EX 1 Video iris lens The pin configuration is subject to EIAJ configuration The differences in configuration are as follows POWER IN The terminal for connection to the DC jack of the power adaptor NOTE The optional Watec power adaptor AD 901 DC 12V 250mA is recommended for use with the WAT 535EX SYNC IN BNC terminal for the external synchronization signal input GAIN CONTROL Gain volume level adjustment Turning the control clockwise or anti clockwise for gain volume level adjustment Pin No EIAJ configuration Watec configuration Power Power Unused NC Control iris signal Control iris signal GND GND GND WAT 535EX Vv X re wiring required NOTE No electron
5. ce etc make sure to avoid any strong electromagnetic field otherwise the video output may be distorted and monitor clearness compromised Do not connect any power supply directly to the terminal of the VIDEO OUT SYNC IN connector This may cause damage os When a cable operation system is being used video signal power coaxial cable transmission check the specifications of your monitor for proper connection to the video signal terminal of the camera Do not make connections and or operate the WAT 535EX with wet hands wO Should the WAT 535EX not work properly switch off the power and then check all the required connectors power cable and if the video cable is properly connected Sunlight shining directly onto the camera lens may cause damage to the CCD CONTENT Using the contents figures below Check to make sure all parts are present before use DESCRIPTION OF PARTS 52 7 Ls 42 1 5 397 8 5 31 2 13 18 lt gt y EIEN FO SYN 88 2 oS AG DJ NE ronin anoo DEO lt Front View gt lt Side View gt lt Back View gt f CCD CS lens mount lris level control Hexagonal focusing adjustment screws X3 Ke rr Auto iris socket Tripod mounting screw holes upper and lower fae VIDEO OUT POWER IN SYNC IN GAIN CONTROL Shutter SW F
6. e monitor This does not mean damage has occurred to the WAT 535EX 9 Select any required functions by setting four Function Switches at upper or lower positions 4 Insert the power jack of the power adaptor to POWER IN on the back panel of the WAT 535EX NOTE Confirm that the power adaptor is not connected before insertion of the power jack into POWER IN The optional Watec power adaptor AD 901 DC 12V 250mA is recommended IMPORTANT NOTE When not using a recommended Watec Power Adaptor A Use a stabilized power adaptor with a voltage range of 12V DC 10 and a current capacity of a more than 250mA B Use the additional DC power jack when the shape or polarity of the power jack of the DC power adaptor can not be inserted into POWER IN on the WAT 535EX lONDI C Wire the DC Power jack as appropriate Use the drawing on the right to guide you CAUTION Be careful not to create a short circuit during the wiring process It may cause damage or even fire to the WAT 535EX and power adaptor if the above care and attention is not adhered to when the power supply is resumed Note How to dismount the lower housing cover of the WAT 535EX O Switch off the power 0 Remove the four fixing screws from the housing cover O Slowly side the housing cover away downwards from the main unit For replacement repeat the above procedure in reverse CAUTION Change any required switch set
7. ic damage occurs to the WAT 535EX even when the Auto iris lens is wired to the Watec configuration instead of the EIAJ configuration but the Auto iris lens will not work correctly When an Auto iris lens which has already been used with other Watec models is used for the WAT 535EX wire the attached iris plug as shown in the above EIAJ configuration 2 DC driven iris lens The pin configuration of a DC driven iris lens is standardized to EIAJ specifications If the DC driven iris lens does not work check the wiring configuration referring to the table below Pin No DC driven iris lens arrangement EIAJ Soa Control DUMP HOZ Control DUMP OS Drive DRIVE O Drive DRIVE QV NOTE Check the configuration of the iris plug before it is connected to Auto iris on the WAT 535EX After connection adjust Iris level for auto iris placed above the iris connector by turning clockwise or anti clockwise as shown above The WAT 535EX is compatible with both a Video iris lens and a DC driven iris lens Patent pending 3 Connect VIDEO OUT on the WAT 535EX with the monitor using a coaxial cable with 75Q impedance such as an RG 58 U or an RG 6 U IMPORTANT NOTE Select a monitor with the same transmission mode as the WAT 535EX there are two versions NTSC and PAL A monitor with more than 700TV lines is recommended CAUTION Do not u
8. se a monitor which uses a video signal power coaxial transmission cable 7 GAIN CONTROL Turn according to your requirements The optimal picture can be obtained under various environments when GAIN CONTROL on the back panel is turned clockwise or anti clockwise as shown below on the left Gain corresponding to the brightness of an object is automatically adjusted in a range between 5dB 32dB when GAIN CONTROL is locked in the AGC position When AGC is set at AGC LO brightness of an object is automatically adjusted to a range between 5dB 20dB O When using the MGC function after unlocking GAIN CONTROL clockwise the gain can be manually fixed in a range between 5 32dB MGC O When a high S N is required in low fluctuating brightness situations lower the gain by turning GAIN CONTROL anti clockwise so as to be able to obtain the best optical picture then adjust the iris function on the lens to the lighting conditions O When there is a dark environment in low fluctuating brightness situations increase AGC Sed the gain by turning GAIN CONTROL clockwise AGC 59B 63 O When a wide depth of field is required first turn the lens iris towards the closed AGS HILO position then adjust the gain using GAIN CONTROL 8 Select any required shutter speed by the Sutter speed selector to one of its 9 positions when required When an object with high brightness is focussed upon especially on shutter operation smearing phenomena may appear on th
9. specifications are subject to change without notice Watec is not responsible for any inconvenience or the attendant damages to the video audio and monitoring recording equipment caused by misuse mis operation or improper wiring of our equipment If for any reason the WAT 535EX does not work properly or if you have any questions regarding installation or operation please contact the distributor or dealer from which it was purchased Watec Co Ltd a zd Address 254 2 Nihonkoku Daihoji Tsuruoka Shi Yamagata Ken 997 0017 Japan Phone 81 235 25 7164 Fax 81 235 23 4409 E mail info watec net
10. ting firmly to avoid any operational or functional instability of the camera How to set Function SW For producing the best possible results adjust the switches to meet your requirements while taking into consideration the use of the WAT 535EX the environment and the desired picture quality 5 Switch on the WAT 535EX monitor and all other allied equipment Remove the power jack of the AD 901 AC adaptor at once whenever the picture does not appear on the monitor 6 Focusing the lens of the WAT 535EX is achieved by adjusting the lens while looking at the monitor screen N B In cases when the WAT 535EX can not be focused manually use the focusing adjustment method set out below 0 Attach the required lens on the WAT 535EX and loosen the three hexagonal focusing adjustment screws Be extremely careful not to drop the lens Set the focus ring to the infinitive position and while looking at the monitor screen move the lens forwards or backwards to focus O Tighten Hexagonal focusing adjustment screws when focusing is completed Switch Setting Effect Example Upon shipment ON Applicable to general surveillance monitoring system V 1 ON OFF When gamma correction function is harmful when storing or OFF downloading pictures onto a computer When gamma correction is not required Oyo When minimum illumination is more important than the S N ratio
11. unction SW Internal View lt Internal View gt Shutter speed selector Nine different manual and electronic shutter speed settings 0 to 9 Shutter speed is set to 9 OFF upon shipment NOTE Installed directly under fluorescent or incandescent lighting may cause flickering on the monitor In order to reduce or eliminate this interference set the SHUTTER speed to the FL setting CCD front face The light receiving face of the CCD camera NOTE 1 Handle the CCD and lens with special care 2 Always attach the lens cap so as to protect the lens and or the CCD from contamination or damage 3 Dirt water or oil deposits on either will cause an unclear picture on the monitor Scratches will cause permanent damage No Mode Shutter Speed seconds 0 FL EIA 1 100 CCIR 1 120 1 ES 1 250 Oe Mies me ce Y 4 ES 1 2000 9 5 ES 1 5000 2G 8 6 ES 1 10000 i ES 1 100000 8 EI EIA 1 60 100000 CCIR 1 50 1 100000 9 OFF EIA 1 60 CCIR 1 50 0 FL Flicker compensation This function is used to reduce the flickering phenomena occurring on the monitor screen caused by fluorescent and mercury lamps This function is effective when used with normal commercial power supplies and is effective at 50Hz in NTSC and 60Hz when using PAL See Sec 7 8 8 EI Electronic iris The iris can be adjusted electronically in accordance with the light intensit
12. y of an object It is more beneficial when used in combination with a fixed iris lens which can not be adjusted to the received light intensity Function SW Parameters of gamma correction AGC and back light compensation adjustable Gamma correction ON OFF AGC HI LOW AGC back light compensation ON OFF EI back light compensation ON OFF SETTING UP AND OPERATION OF THE WAT 535EX Water WAT 535EX o Lens Mount Cap WAT 535EX DC Plug Iris Connector Operation Manual OPERATION MANUAL CS lens mount Any standard model C mount lens can be attached to the WAT 535EX using the optional C mount ring 34CMA R lris level Auto iris volume level adjustment When using a DC driven iris lens the volume level of the Auto iris can be adjusted using this function Hexagonal focusing adjustment screws for fine focusing adjustment using the lens mounting ring There are three hexagonal focusing adjustment screws each placed at intervals of 120 around the lens mount ring allowing for the forward and backward motion of the lens mount Auto iris socket Power and control signals are supplied to the auto iris lens when the auto iris lens is used See Sec 2 of the Operation Manual for more detailed attention Patent pending Tripod mounting screw holes upper and lower Thread size and depth are the same as that for standard camera tripods VIDEO OUT The BNC terminal for video signal output NO
Download Pdf Manuals
Related Search