Home

IntesisBox ME-AC-KNX-1i v1.0

1. Figure 4 37 Parameter detail Temp delta decrease HEAT or increase COOL 9C This parameter lets configure the delta temperature increase or decrease that will be applied when the timeout has elapsed A Important When there is occupancy again after the application of a delta the same delta will be applied inversely i e In a room with AC in cool mode and 25 C setpoint temperature a 2 C delta is applied after the occupancy timeout setting the setpoint at 279C because there is no occupancy in the room If the setpoint is raised to 299C during that period when the room is occupied again a 20C delta will be applied and the final setpoint temperature will then be 279C Enable secondary timeout If set to no nothing will be applied If set to yes a new timeout will be enabled and two new parameters will appear Intesis Software S L All rights reserved URL http www intesis com 41 63 This information is subject to change without notice n te S i S E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng gt Timeout to apply action 2 min T Action after timeout Apply Preset Delta elapsed Temp delta dec HEAT 2 0 C or inc COOL 9C Figure 4 38 Parameter detail gt Timeout to apply action minutes This parameter lets choose how much time to w
2. Binary Input 3 Configuration for Control Binary Input 4 Configuration E LtL L litL cR Los E Enable use of bit type Mode objects No for Status Enable use of Text object for Mode No z Enable use of Legacy object for Mode No X compatible with old vers of XXACKNX1 Figure 4 6 Default Mode Configuration dialog All the parameters in this section are related with the different mode properties and communication objects Fd 1 Control Mode DPT 20 105 1byte 0 Aut 1 Hea 3 Coo 9 Fan 14 Dry The byte type communication object for Mode works with the DTP 20 105 Auto mode will be enabled with a O value Heat mode with a 1 value Cool mode with a 3 value Fan mode with a 9 value and Dry mode with a 14 value 4 2 1 Indoor unit has FAN mode This parameter has to be used to indicate if the indoor unit has the fan mode available o If set to no the indoor unit doesn t have the fan mode available o If set to yes the infoor unit has the fan mode available A Important Read the documentation of your indoor unit to check if it has FAN mode available 4 2 2 Enable use of Heat Cool bit type obj This parameter shows hides the Control and Status Mode Cool Heat communication objects a Control Mode Cool Heat DPT 1 100 1bit Cool1 Heat 27 56 Status Mode Cool Heat DPT 1 100 1bit 0 Cool 1 Heat o If set to no the objects will not be shown o If set to yes the Control and Sta
3. 1bit 0 Enable 1 Disable a 90 Control Disable Input 1 DPT 1 003 1bit 0 Disable 1 Enable o If set to no any object will be shown o When DPT 1 003 O Disable 1 Enable is selected the input can be disabled using the value O and enabled using the value 1 o When DPT 1 002 O Enable 1 Disable is selected the input can be disabled using the value 1 and enabled using the value O 4 9 5 Function This parameter lets choose the function that will have the binary input There are 7 different functions available Switching Dimming Shutter Blind Value Execute Scene internal Occupancy internal and Window Contact internal o When Switching is selected the communication object and new parameters for the Input x will appear as shown below g 30 Status Inl Switching DPT 1 001 1bit 0 Off1 On gt Function Switching gt Send telegram after No action bus recovery gt Value on raising edge Toggle On Off contact activated gt Value on falling edge No action contact deactivated gt Cyclical sending Never Figure 4 42 Parameter detail Send telegram after bus recovery This parameter lets select if the Binary Input x will send a telegram or not after a bus recovery and the type of telegram sent if enabled e When No action is selected no telegram will be sent after a bus recovery e When Current status
4. Pos4 20 Posi 40 Pos2 60 Pos3 Status Vanes U D 5 pos 1 byte DPT Scaling 5 001 80 Pos4 100 Pos5 Status Vanes U D 5 pos 1 byte DPT Enumerated 5 010 ub o MN oc MEI 5 010 L Li llllolsis 4 Pos4 5 Pos5 EN Status Vanes U D Man Auto DPT Bool 1 002 el ft 0 Manual 1 Auto omo Status Vanes U D Pos1 DPT Bool 1 002 RT 1 Position 1 om Status Vanes U D Pos2 DPT Bool 1 002 R 1 Position 2 NAM Status Vanes U D Pos3 DPT Bool 1 002 R 1 Position 3 Intesis Software S L All rights reserved URL http www intesis com 61 63 This information is subject to change without notice amp ntes i E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL LA A tel 134 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r1 eng Status Vanes U D Pos4 1 bit DPT Bool 1 002 1 Position 4 Lm seven im emma Dum fo pes m meceeuosus e comme aco r p pesniesm 000000 e me vn Ten sem ors sos oor m fef jmumme oe mecs zone emmeme moe rf feo ce aes acrewnrenseioe zone oromemme mo ff feo m meme um oven 0s e fr eememiomem 0000 m emn errcae rem teen a one eron may oner emm e sone errena nee orr sna seso uon a fr acre eron enmon De meme ue mee quee fr oom 0 e sone samome ue mem quede fr eemim 000 Dee im saanen aoe mee roo faf D eonim o Le imna saanee roe cms n
5. gt Does sequence include No AUTO vanes Up Down gt Does sequence include No SWING vanes Up Down CE SENE NN gt Rollover Vanes at upper lower limit Yes when controlling with obj SN Figure 4 23 Parameter detail gt DPT type for Vane Up Down obj This parameter lets choose between the datapoints O Up 1 Down DPT 1 008 and O Decrease i Increase DPT 1 007 for the Contro Vanes U D object gt Does sequence include AUTO vanes Up Down This parameter lets choose if AUTO function is included yes or not no in the sequence when using Control Vanes U D object as shown in the discontinuous segment at the picture below gt Does sequence include SWING vanes Up Down This parameter lets choose if SWING function is included yes or not no in the sequence when using Contro Vanes U D object as shown in the discontinuous segment at the picture below Roll over Vanes at upper lower limit This parameter lets choose if roll over will be enabled yes or disabled no for the Contro Vanes U D object Only if Roll over is enabled gt AUTO p gP 2 P 3 g P 4 ZP 5t E SW 51 Only if Roll over is enabled Up Increase a Down Decrease If Available 4 5 6 Enable use of bit type Vane U D objects for Control This parameter shows hides the bit type Control Vanes U D objects Intesis Software S L All r
6. 1 value has to be sent to the scene s object we want to store i e to store scene 4 a 1 has to be sent to the Control Store Scene 4 object 4 7 3 Enable use of bit objects for scene execution This parameter shows hides the Control Execute Scene bit type communication objects Intesis Software S L All rights reserved URL http www intesis com 36 63 E This information is subject to change without notice n tes i S E Email info intesis com software IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng af 45 Control Execute Scene 1 DPT 1 002 1bit 1 Execute Scene 1 a 46 Control Execute Scene 2 DPT 1 002 1bit 1 Execute Scene 2 8247 Control Execute Scene 3 DPT 1 002 1bit 1 Execute Scene 3 ay 4s Control Execute Scene 4 DPT 1 002 1bit 1 Execute Scene 4 af 49 Control Execute Scene5 DPT 1 002 1bit 1 Execute Scene 5 Enable use of bit objects yes for scene execution Figure 4 31 Parameter detail o If set to no the communication objects will not be shown o If set to yes the communication objects will appear To execute a scene by using these objects a 1 value has to be sent to the scene s object we want to execute i e to execute scene 4 a 1 has to be sent to the Control Execute Scene 4 object 4 7 4 Scene x preset This parameter lets define a preset for a scene
7. DPT 5 010 is selected Contro Fan Speed and Status Fan Speed communication objects for this DPT will appear a 11 Control Fan Speed 4 Speeds DPT 5 010 lbyte Speed values 1 2 3 4 Pa 63 Status Fan Speed 4 Speeds DPT 5 010 1byte Speed Values 1 2 3 4 The first fan speed will be selected if a 1 is sent to the Control object The second one will be selected sending a 2 the third one if available will be selected sending a 3 the fourth one if available will be selected sending a 4 The Status object will always return the value for the fan speed selected A Important If a O value is sent to the Control object the minimum fan speed will be selected If a value bigger than 4 is sent to the Control object then the maximum fan speed will be selected Intesis Software S L All rights reserved URL http www intesis com 22 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng o When Scalin ic eia deer selected E ntrol_ Fan Speed and Status_ Fan Speed ommunicatio ects for this DPT will 2 appea Fd li Control Fan Speed 4 Speeds DPT 5 001 1byte Thresholds 38 63 and 88 Fd 63 Status Fan Speed 4 Speeds DPT 5 001 1byte 2525 50 75 and 100 The next table Show the range
8. User s manual r2 eng o If set to no the objects will not be shown o If set to yes the Control Fan Speed objects for Speed 1 Speed 2 Speed 3 if available and Speed 4 if available will appear To activate a Fan Speed by using these objects a 1 value has to be sent 4 4 8 Enable use of bit tyoe Fan Speed objects for Status This parameter shows hides the bit type Status_ Fan Speed objects a 65 Status Fan Speed 1 DPT 1 002 1bit 1 Fan in speed 1 P4 66 Status Fan Speed 2 DPT 1 002 1bit 1 Fan in speed 2 2 67 Status Fan Speed 3 DPT 1 002 1bit 1 Fan in speed 3 B 68 Status Fan Speed 4 DPT 1 002 1bit 1 Fan in speed 4 o If set to no the objects will not be shown o If set to yes the Status Fan Speed objects for Speed 1 Speed 2 Speed 3 if available and Speed 4 if available will appear When a Fan Speed is enabled a 1 value is returned through its bit type object 4 4 9 Enable use of Text object for Fan Speed This parameter shows hides the Status Fan Speed Text communication object E 69 Status Fan Speed Text DPT 16 001 14byte ASCI String o If set to no the object will not be shown o If set to yes the Status Fan Speed Text object will appear Also in the parameters will be shown five text fields one for each Fan Speed that will let modify the text string displayed by the Status Fan Speed Text when changing a fan speed gt String when fan
9. gt Function Execute scene internal Scene when contact is activated Scene 1 needs to be defined Figure 4 52 Parameter detail Scene when contact is activated This parameter lets choose the scene that will be activated on a rising edge This scene MUST be defined in the Scene Configuration dialog as a preset o When Occupancy internal is selected the binary input x will have the same behavior as configured in the parameter Enable use of Occupancy function inside the Switch Off Timeouts Configuration dialog gt Function Occupancy internal Figure 4 53 Parameter detail o When Window Contact internal is selected the binary input x will have the Same behavior as configured in the parameter Enable use of Open Window Switch off timeout function inside the Switch Off Timeouts Configuration dialog Function Window Contact internal Figure 4 54 Parameter detail Intesis Software S L All rights reserved URL http www intesis com 52 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 5 Specifications ABS UL 94 HB 2 5 mm thickness Dimensions S9x4ox2oimm Weight 35g o O Power suppl ddp UR PPY E through KNX bus LED indicators
10. once started gt Setpoint delta increase HEAT or decrease COOL in Celsius Number of degrees Celsius that will increase in Heat Mode or decrease in Cool Mode while in Power Mode gt Fan Speed for this mode Fan Speed that will be set in the unit while in Power Mode 4 3 2 Enable use of ECONOMY mode This parameter shows hides the Control_ Econo Mode and Status Econo Mode communication objects The Econo Mode lets change the Setpoint Temperature and the Fan Speed within a given period of time a 36 Control Econo Mode DPT 1 010 1bit 0 Stop 1 Start B 8 Status Econo Mode DPT 1 001 1bit 0 OfF1 On o If set to no the objects will not be shown o If set to yes the Contro Econo Mode and Status Econo Mode objects and new parameters will appear e When a 1 value is sent to the Contro communication object EconoMode will be enabled and the Status object will return this value Intesis Software S L All rights reserved URL http www intesis com 18 63 This information is subject to change without notice n te S i S E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng e When a O value is sent to the Contro communication object EconoMode will be disabled and the Status J object will return this value A Important This mode will ONLY work if the indoor unit is
11. the Status Operation Hour Counter object will appear e This object can be read and sends its status every time an hour is counted The gateway keeps that count in memory and the status is sent also after a KNX bus reset failure Although this object is marked as a Status object it also can be written to update the counter when needed To reset the counter should be written a O value A Important This object comes by default without the write W flag activated If is necessary to write on it this flag must be activated A Important This object will also return its status every time a value is written only if it s different from the existing one A Important If the stored value is O hours the gateway will not send the status to KNX 4 1 6 Enable object Error Code 2byte This parameter shows hides the Status_ Error Code communication object which shows the indoor unit errors if occurred in numeric format 2 82 Status Error Code 2byte 0 Mo error Any other see man o If set to no the object will not be shown o If set to yes the Status Error Code 2byte object will appear e This object can be read and also sends the indoor unit error if occurred in numeric format If a O value is shown that means no error 4 1 7 Enable object Error Text Code 14byte This parameter shows hides the Status Error Text Code communication object which shows the indoor unit errors if occurred in text format 2 83
12. the following description is valid for all the scenes Scene 1 preset yes scene will NOT be modifiable from KNX bus Figure 4 32 Parameter detail o If set to no the preset for the scene x will be disabled o If set to yes the preset will be enabled When a scene is executed the values configured in the preset will be aplied A Important If a scene s preset is enabled will not be possible to modify store the scene from the KNX bus Scene 1 Value for On Off ON Scene 1 Value for Mode COOL gt Scene 1 Value for Fan Speed FAN SPEED 3 if available if available VANES U D POS 5 if available gt Scene 1 Value for Vanes U D if available gt Scene 1 Value for Setpoint Temp 22 0 za gt Scene 1 Value for Remote Lock unchanged Figure 4 33 Parameter detail Intesis Software S L All rights reserved URL http www intesis com 37 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng gt Scene x Value for On Off This parameter lets choose the power of the indoor unit when the scene is executed The following options are available ON OFF or unchanged gt Scene x Value for Mode This parameter lets choose the mode of th
13. 2 U D POS 2 gt String when vanes U D in POS 3 U D POS 3 String when vanes U D in POS 4 U D POS 4 gt String when vanes U D in POS 5 U D POS 5 if available gt String when vanes U D in SWING U D SWING Figure 4 24 Parameter detail Intesis Software S L All rights reserved URL http www intesis com 31 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 5 11 Enable use of Legacy object for Vanes This parameter shows hides the Legacy Vanes communication object g2 100 Legacy Vanes Enumerated 1byte 0 Auto 1 5 pos1 5 6 Swing o If set to no the communication object will not be shown o If set to yes the communication object will appear This object lets change the indoor unit vanes behavior but it uses a different data type It is used to maintain compatibility with old gateway models 46 Temperature Configuration dialog Device 1 1 1 ME AC Interface General dd Periodic sending of Status AC Setp 0 Mode Confi ti pm orale cop in seconds O No periodic sending Special Modes Configuration Fan Speed Configuration Transmission of Status AC Return Temp Only cyclically 4 Vanes Up Down Configuration Temperature Configuration Status AC Return Temp periodic 180 EXTXIN
14. 5 10 Enable use of Text object for Vane U D eeeesseeennn nnnm nnnm 31 4 5 11 Enable use of Legacy object for Vanes ssssssseseeeee emen nnn nnn 32 4 6 Temperature Configuration dialog ccesssseeeeee nennen 32 4 6 1 Periodic sending of Status AC Setp cc cccccccccceesseeeeeeeensecsseenetreeseseaguas 32 4 6 2 Transmission of Status AC Return Temp sssssssseeeee nemen 33 4 6 3 Enable use of object for Setpoint Temp seen 33 Intesis Software S L All rights reserved s RL htto www intesis com This information is subject to change EU notice Intesis a sun aea Aa CO 4 63 IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 6 4 Enable limits on Control Setpoint obj sseessseeeeen mmm nn 34 4 6 5 Ambient temp ref is provided from KNX ssssseeeen Hmm 34 4 7 Scene configuration dialog cesesiasxcusadatrEa n Vas uui vilia ud aa aiSad bas aa are va a aa 35 4 7 1 Enable use of SCENES xisesviva eres is e4 dXX TATVEPUIATENSP ari SR Rd dd FPPPUDREPEd REPE eres 35 4 7 2 Scenes can be stored from KNX bus eeeeseeeeen nnnm nnnm nnn nnne 36 4 7 3 Enable use of bit objects for scene execution sseeeenn nnnm nnn 36 4 7 4 oceans x Dr E reiini eeprdt eiae Uter EEPPIN MDPaPIacEREE FETU EFC UII DN RI Rn IRE 37 4 8 Switch Off Timeouts Configura
15. Text object will appear Also in the parameters will be shown five text fields one for each mode that will let modify the text string displayed by the Status Mode Text when changing mode gt String when mode is AUTO AUTO gt Sting when mode is HEAT HEAT String when mode is COOL COOL gt String when mode is FAN FAN gt String when mode is DRY DRY Figure 4 8 Parameter detail 4 2 8 Enable use of Legacy object for Mode This parameter shows hides the Legacy Mode communication object a 98 Legacy Mode Enumerated 1byte 0 Aut1 Hea 2 Dry 3 Fan 4 Coo o If set to no the communication object will not be shown Intesis Software S L All rights reserved URL http www intesis com 16 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng o If set to yes the Legacy Mode communication object will appear This object lets change the indoor unit mode but it uses a different data type It is used to maintain compatibility with old gateway models 43 Special Modes Configuration dialog Device 1 1 1 ME AC Interface General Enabl f POWER mod No x Mode Configuration AN er ooo Special Modes Configuration Enable use of ECONOMY mode No M Fan Speed Configuration Vanes Up Down Configuration E
16. an increase step after a decrease step and viceversa A Important Note that the first long operation in toggle depends on the last short operation meaning that after a 1 value will be sent a decrease step and after a O value will be sent an increase step A Important The time period between a short and a long operation is defined in the parameter Short long operation limit x100ms Increasing step This parameter lets select the increasing step value in 9o that will be sent for a long operation gt Decreasing step This parameter lets select the decreasing step value in that will be sent for a long operation Intesis Software S L All rights reserved URL http www intesis com 48 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng Short long operation limit x100ms This parameter lets introduce the time period difference for the short and the long operation gt Cycl send period in long oper x100ms This parameter lets configure a time in seconds for the cyclical sending of a long operation o When Shutter Blind is selected the communication objects and new parameters for the Input x will appear as shown below a 94 Status In3 Shut Blind Step DP
17. for the mentioned Control objects are also available to use if needed Also objects Status AC Return Temp and Status Error Alarm are shown 4 41111 ME AC Interface 870 Control On Off DPT 1 001 Lbit 0 OfF1 On a 1 Control Mode DPT 20 105 1byte 0 Aut Hea 3 Coo9 Fan 14 Dry a 11 Control Fan Speed 2 Speeds DPT 5 001 1byte Threshold 75 8777 Control Setpoint Temperature DPT 9 001 2byte C E 54 Status On Off DPT 1 001 1bit 0 Off 1 On a 95 Status Mode DPT 20 105 1byte 0 Auti1 Hea j3 Coo 9 Fan 14 Dry a 63 Status_ Fan Speed 2 Speeds DPT 5 001 1byte 50 and 100 8779 Status AC Setpoint Temp DPT 9 001 2byte C 27 60 Status AC Return Temperature DPT 9 001 2byte C E 81 Status Error Alarm DPT 1 005 1bit 0 Mo alarm 1 Alarm 2 B3 Status Error Text Code DPT 16 001 14byte 4 char ME Error Empty None Figure 4 2 Default communication objects Intesis Software S L All rights reserved URL http www intesis com 9 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL een 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 1 General dialog Inside this parameter s dialog it is possible to activate or change the parameters shown in the Figure 4 1 The first field shows the URL where to download the data
18. higher Position will be selected o When Scaling DPT 5 001 is selected Control Vane Up Down and Status Vane Up Down communication objects for this DPT will appear Fd 18 Control Vanes U D 5 Pos DPT 5 001 1byte Thresholds 3075 50575 70 and 9055 87 70 Status Vanes U D 5 pos DPT 5 001 1byte 20 40 60 80 and 100 The next table shows the range of values that can be sent through the Control object and the value returned by the Status object A Important Read the documentation of your indoor unit to check how many vane positions are available 4 5 5 Enable use of object for Vanes U D This parameter shows hides the Control Vane Up Down communication object which lets change the indoor unit vane position by using two different datapoint types 8726 Control Vanes U D DPT 1 007 1bit 0 Decrease i Increase o If set to no the object will not be shown o If set to yes the Control Vanes U D object and a new parameter will appear Intesis Software S L All rights reserved s URL http www intesis com 28 63 This information is subject to change without notice n te S i S E Email infoQintesis com IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng Enable use of object for Vanes U D Yes gt DPT type for Vanes U D object 0 Decrease l Increase DPT 1 007
19. is selected the binary input will send a telegram with its current status after a bus recovery Also a new parameter will appear see below Intesis Software S L All rights reserved URL http www intesis com 45 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng e When On is selected the binary input will send a telegram with a 1 value after a bus recovery Also a new parameter will appear see below e When Off is selected the binary input will send a telegram with a O value after a bus recovery Also a new parameter will appear see below Sending delay after 10 bus recovery seconds gg a Figure 4 43 Parameter detail gt Sending delay after a bus recovery seconds This parameter lets configure a delay in seconds that will be applied after a bus recovery and after which a telegram will be sent gt Value on rising edge This parameter lets select the value that the Binary Input x will send on a rising edge contact activated e When On is selected the binary input will always send telegrams with a 1 value e When Off is selected the binary input will always send telegrams with a o value e When Toggle On Off is selected the binary input will send
20. not be shown o If set to yes the Control Occupancy object and new parameters will appear If a 1 value is sent to this object no room occupancy the timeout will begin If a O value is sent to this object the timeout will stop Intesis Software S L All rights reserved URL http www intesis com 40 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng Enable use of Occupancy function lyes gt Timeout to apply action minutes 2 gt Action after timeout elapsed Apply Preset Delta Figure 4 36 Parameter detail gt Timeout to apply action minutes This parameter lets choose how much time to wait in minutes before executing the action specified in the next parameter Action after timeout elapsed gt Action after timeout elapsed When Switch Off is selected once the timeout has elapsed the indoor unit will be turned off When Apply Preset Delta is selected once the timeout has elapsed a delta temperature will be applied in order to save energy decreasing the setpoint when in Heat mode or increasing the setpoint when in Cool mode Also new parameters will appear gt Temp delta decrease HEAT or 2 0 C increase COOL PC X gt Enable secondary timeout yes
21. over will be enabled yes or disabled no for the Control_ Fan Speed object Only if Roll over is enabled gt AUTO gt fs Z gt FS2 Zo FS3 gt gt FS4 E Only if Roll over is enabled Up Increase Down Decrease If Available 4 4 6 Enable Fan Speed Manual Auto objects for Control and Status This parameter shows hides the bit type Control Fan Speed Manual Auto objects a 12 Control Fan Speed Manual Auto DPT 1 002 1bit 0 Manual 1 Auto Fd 64 Status Fan Speed Manual Auto DPT 1 002 1bit 0 Manual 1 Auto o If set to no the Control Fan Speed Manual Auto communication objects will not be shown o If set to yes the Control Fan Speed Manual Auto communication objects will appear 4 4 7 Enable use of bit type Fan Speed objects for Control This parameter shows hides the bit type Control Fan Speed objects 27 13 Control Fan Speed 1 DPT 1 002 1bit 1 Set Fan Speed 1 a 14 Control Fan Speed 2 DPT 1 002 1bit 1 Set Fan Speed 2 2 15 Control Fan Speed 3 DPT 1 002 1bit 1 Set Fan Speed 3 E 16 Control_ Fan Speed 4 DPT 1 002 1bit 1 5et Fan Speed 4 Intesis Software S L All rights reserved URL http www intesis com 24 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C
22. registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng gt Reload last On Off value yes when Occupied gt Disallow On Off operation while yes not Occupied Figure 4 39 Parameter detail gt Reload last On Off value when Occupied If set to no once the switch off timeout has elapsed any value will be reloaded If set to yes once the switch off timeout has elapsed the last On Off value will be reloaded e If a 1 value is sent to the Control Occupancy object after the timeout period the indoor unit will turn on e If a O value is sent to the Control Occupancy after the timeout period no action will be performed 4 8 3 Enable use of SLEEP timeout This parameter shows hides the Control Sleep Timeout communication object which lets start a timeout to automatically turn off the indoor unit 2 32 Control Sleep Timeout DPT 1 010 1bit 0 Stop 1 Start o If set to no the object will not be shown o If set to yes the Control Sleep Timeout object and a new parameter will appear If a 1 value is sent to this object the switch off timeout will begin If a O value is sent to this object the switch off timeout will stop Enable use of SLEEP timeout yes gt Sleep function switch off timeout 1 minutes Figure 4 40 Parameter detail Timeout to apply action minutes This parameter lets select how much
23. time in minutes to wait before switching off the AC unit Intesis Software S L All rights reserved URL http www intesis com 43 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 9 Binary Input x Configuration dialog Device 1 1 1 ME AC Interface General Enabl f Input 1 Yes x Mode Configuration EH E Mes 3 Special Modes Configuration Contact type NO Normally Open Fan Speed Configuration ee Vanes Up Down Configuration gt Debounce time 50 ms X Temperature Configuration Scene Configuration Disabling function DPT 1 002 1 True Disable O False Enable X Switch Off Timeouts Configuration aac ISI ERR EE gt Function Switching H Binary Input 1 Configuration CC Binary Input 2 Configuration gt Send telegram after No action X Binary Input 3 Configuration bus recovery Binary Input 4 Configuration gt Value on raising edge No action x contact activated Value on falling edge No action contact deactivated E gt Cyclical sending Never H Figure 4 41 Binary Input Configuration dialog Al the parameters in this section are related with the binary inputs properties and communication objects 4 9 1 Enable use of Input x This
24. yes the Control Setpoint Temp object and a new parameter will appear Enable use of obj for Setp Temp yes gt DPT type for Setp Temp object 0 Up 1 Down DPT 1 008 ka Figure 4 28 Parameter detail gt DPT type for Setp Temp object This parameter lets choose between the datapoints O Up 1 Down DPT 1 008 and O Decrease 1 Increase DPT 1 007 for the Control Setpoint Temp object Lower limit 199C 20 C ac T rad 27 C Pad 28 C Upper limit Up Increase a Down Decrease Intesis Software S L All rights reserved URL http www intesis com 33 63 This information is subject to change without notice n tes i S E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 6 4 Enable limits on Control Setpoint obj This parameter enables to define temperature limits for the Control Setpoint Temperature object Enable limits on Control Setpoint obj Yes gt Lower limit C 19 0 C gt Upper limit 2C 28 0 C Figure 4 27 Parameter detail o If set to no the setpoint temperature limits for the Contro _ Setpoint Temperature object will be the default 19 C for the lower limit and 28 C for the upper limit o If set to yes it is possible to define temperature limits for the Control Setpoint Temperature object gt Control Set Temp Lower li
25. 1 x KNX IPC J Q 1 x KNX 1 x KNX programming eee 4 x Potential free binary inputs Signal cable length 5m uschielded may be extended up to 20m with twisted Binary inputs Compliant with the following standards IEC61000 4 2 level 4 15kV air discharge 8kV contact discharge MIL STD 883E Method 3015 7 class3B Configuration Configuration with ETS 0000000000 with Configuration with ETS 0000000000 Operating 7 Temperature Isolation Voltage Isolation Voltage 4000V Compliant with RoHS directive 2002 95 CE CE conformity to EMC directive 2004 108 EC and Low voltage directive 2006 95 EC EN 61000 6 2 EN 61000 6 3 EN 60950 1 EN 50491 3 EN 50090 2 2 EN 50428 EN 60669 1 EN 60669 2 1 Certifications 21 mm X Bn c AC Indoor Unit Connection 45 mm KNX bus Connection Programming Switch Programming LED Intesis Software S L All rights reserved URL http www intesis com 53 63 E This information is subject to change without notice n te S i S E Email info intesis com SO r tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 6 AC Unit Types compatibility A list of Mitsubishi Electric indoor unit models compatible with ME AC KNX 1i and their available features can be found in http www intesis com pdf IntesisBox ME AC xxx 1 AC Compatibi
26. All rights reserved URL http www intesis com 21 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 4 3 Indoor unit has AUTO fan speed This parameter lets choose if the indoor unit has Auto Fan Speed available or not Indoor unit has AUTO fan speed Yes see docum for your indoor unit p Figure 4 14 Parameter detail o If set to no all the parameters and communication objects for the Auto Fan Speed will not be shown o If set to yes a new parameter will appear Find more information on section 2 4 6 Enable Fan Speed Manual Auto objects Enable Fan Speed Manual Auto objects No for Control and Status es Figure 4 15 Parameter detail A Important Read the documentation of your indoor unit to check if Auto Fan Speed is available 4 4 4 DPT object type for fanspeed With this parameter is possible to change de DPT for the Control Fan Speed and Status Fan Speed byte type communication objects Datapoints Scaling DPT 5 001 and Enumerated DPT 5 010 can be selected A Important The communication objects shown in this section may be different depending on the number of fan speeds available although they all share the same communication object number o When Enumerated
27. IntesisBox ME AC KNX 11 v1 0 User s Manual Issue Date 30 05 2012 r2 eng Intesisg IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng Intesis Software S L All Rights Reserved Information in this document is subject to change without notice The software described in this document is furnished under a license agreement or nondisclosure agreement The software may be used only in accordance with the terms of those agreements No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or any means electronic or mechanical including photocopying and recording for any purpose other than the purchaser s personal use without the written permission of Intesis Software S L Intesis Software S L Mila Fontanals 1 bis 1 08700 Igualada opain TRADEMARKS All trademarks and trade names used in this document are acknowledged to be the copyright of their respective holders Intesis Software S L All rights reserved URL http www intesis com 2 63 amp This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng Gateway for integration of Mitsubishi Electric air conditioners into KNX TP 1 EIB control systems Compatible with Domestic and Mr Slim line air conditioners commer
28. NEPUES oF B sending time in sec dd Scene Configuration Switch Off Timeouts Configuration Enable use of obj for Setpoint Temp No Binary Input 1 Configuration mnm Binary Input 2 Configuration Enable limits on Control Setpoint obj No v Binary Input 3 Configuration Ambient temp ref is provided from KNX No carefully read User Guide if enabled E TB Binary Input 4 Configuration Figure 4 25 Default Temperature Configuration dialog Al the parameters in this section are related with the Temperature properties and communication objects 4 6 1 Periodic sending of Status AC Setp This parameter lets change the interval of time in seconds from O to 255 at the end of which the AC setpoint temperature is sent to the KNX bus For a 0 value the AC setpoint temperature will ONLY be sent on change The AC setpoint temperature is sent through the communication object Status AC Setpoint Temp 22 79 Status AC Setpoint Temp DPT 9 001 2byte C ag Periodic sending of Status AC Setp 255 in seconds 0 No periodic sending 1 Figure 4 26 Parameter detail A Important In case the ambient temperature is provided from KNX the setpoint temperature returned from this object will be the one resulting from the formula shown in the section 2 6 5 Ambient temp ref is provided from KNX Intesis Software S L All rights reserved URL http www intes
29. Status Error Text Code DPT 16 001 14byte 4 char ME ErroriEmpty Mone o If set to no the object will not be shown o If set to yes the Status Error Text Code object will appear e This object can be read and also sends the indoor unit error if occurred in text format The errors shown have the same format as at the remote controller and at the error list from the indoor unit manufacturer If the object s value is empty that means no error Intesis Software S L All rights reserved URL http www intesis com 12 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 2 Mode Configuration dialog Device 1 1 1 ME AC Interface Indoor unit has FAN mod y ndoor unit has mode es v Mode Configuration see docum for your indoor unit l Special Modes Configuration Fan Speed Configuration Enable Mode Cool Heat objects No v Vanes Up Down Configuration Meinen ieu Temperature Configuration Enable PID Compat Scaling Mode objects No v Scene Configuration for Control Switch Off Ti ts Configurati S n i MEE Or Enable use of object for Mode No Binary Input 1 Configuration Binary Input 2 Configuration Enable use of bit type Mode objects No gt
30. T 1 023 1bit 0 Step Up 1 Step Down 2 35 Status In3 Shut Blind Move DPT 1 023 1bit 0 Move Up 1 Move Down gt Function Shutter Blind gt Send telegram after No action bus recovery l M gt Operation Togg le Up Down gt Method Step Move Step gt Short long operation limit 10 x100ms noms gt Vanes adjustment time 10 x100ms l Figure 4 47 Parameter detail gt Send telegram after bus recovery This parameter lets select if the Binary Input x will send a telegram or not after a bus recovery and the type of telegram sent if enabled e When No action is selected no telegram will be sent after a bus recovery e When Move Up is selected the binary input will send a telegram with a o value after a bus recovery Also a new parameter will appear see below e When Move Down is selected the binary input will send a telegram with a 1 value after a bus recovery Also a new parameter will appear see below E Je gt Sending delay after bus recovery seconds Figure 4 48 Parameter detail gt Sending delay after a bus recovery seconds This parameter lets configure a delay in seconds that will be applied after a bus recovery and after which a telegram will be sent Intesis Software S L All rights reserved URL http www intesis com 49 63 E This information is subject to change without notice n te S i S E Email info intesis com te
31. a 1 value after a 0 value and viceversa e When No action is selected the binary input will not perform any action Value on falling edge This parameter lets select the value that the Binary Input x will send on a falling edge contact deactivated e When On is selected the binary input will always send telegrams with a 1 value e When Off is selected the binary input will always send telegrams with a o value e When Toggle On Off is selected the binary input will send a 1 value after a 0 value and viceversa e When No action is selected the binary input will not perform any action gt Cyclical sending This parameter lets enable disable cyclical sending when a determined condition is met Intesis Software S L All rights reserved URL http www intesis com 46 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng e When When output value is On is selected everytime a 1 value is sent it will be sent cyclically Also a new parameter will appear see below e When When output value is Off is selected everytime a O value is sent it will be sent cyclically Also a new parameter will appear see below e When Always is selected the binary input will send any va
32. ait in minutes before executing the action specified in the next parameter Action after timeout elapsed Action after timeout elapsed When Switch Off is selected once the timeouthas elapsed the indoor unit will turn off When Apply Preset Delta is selected once the timeout configured is extinguished a delta temperature will be applied decreasing the setpoint when in Heat mode or increasing the setpoint when in Cool mode Also new parameters will appear Temp delta decrease HEAT or increase COOL 9C This parameter lets configure the delta temperature that will be applied when the timeout is extinguished A Important When there is occupancy again after the application of a delta the same delta will be applied inversely as explained above gt Disallow On Off operation while not Occupied If set to no On Off commands while the window is open will be accepted e Ifa 1 value is sent to the Contro Occupancy object the switch off timeout period will begin again e If a O value is sent to the Control Occupancy object no action will be performed If set to yes On Off commands while not occupied will be saved but not applied These commands will be used in the next parameter if set to yes Intesis Software S L All rights reserved URL http www intesis com 42 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a
33. base and the user manual for the product 4 1 1 Send READs for Control objects on bus recovery When this parameter is enabled ME AC KNX 1i will send READ telegrams for the group addresses associated on its Control objects on bus recovery or application reset start up o If set to no the gateway will not perform any action o If set to yes all Contro objects with both Transmit T and Update U flags enabled will send READs and their values will be updated with the response when received send READs for Control objects on bus yes recovery T and U flags must be active fce gt Delay before sending READs sec 30 Figure 4 3 Parameter detail Delay before sending READs sec With this parameter a delay can be configured between O and 30 seconds for the READs sent by the Control objects This is to give time enough to other KNX devices on the bus to start up before sending the READs 4 1 2 Scene to load on bus recovery startup This parameter executes a selected scene on bus recovery or startup only if the selected scene has an enabled preset or values previously saved from KNX bus see Scene Configuration dialog If the gateway is disconnected from the indoor unit the scene will not be applied even when connecting to the indoor unit again Scene to load on bus recovery startup scene 2 needs to define vals for that scene nx Figure 4 4 Parameter detail 4 1 3 Disallow control from remote controlle
34. bjects 1 bit DPT Bool 1 002 0 Unlocked 1 Locked WIT Control_ Power Mode 1 bit DPT_Start 1 010 owi 0 Stop 1 Start Control Econo Mode 1 bit DPT Start 1 010 wl 0 Stop 1 Start 37 Control Additional Heat 1 bit DPT Start wl 0 Stop 1 Start Control Additional Cool 1 bit DPT Start l wit 0 Stop 1 Start M O to 4 Exec Scene 1 to 5 128 to 132 Save Scene 1 to 5 ENT RN MNT RN jememme 000000 jeeme 700000 IT RN u Control Save Exec Scene 1 byte DPT SceneControl 18 001 E E E J i j i F T 1 Execute Scene D 1 Execute Scene 1 Execute Scene 1 Execute Scene Intesis Software S L All rights reserved URL http www intesis com 59 63 This information is subject to change without notice amp Int Email info intesis com IntesisBox is a registered trademark of Intesis Software SL n esis E tel 34 938047134 Execute Scene 0 Enable 1 Disable 0 Disable 1 Enable n m O O m N N N N N N N N N N O O s jsjsje issues zjx s sj 0 Enable 1 Disable IntesisBox KNX Mitsubishi Electric A C User s manual r1 eng Control Disable Input 2 1 bit DPT Enable 1 003 0 Disable 1 Enable om amas iw mme Dump jemenitem con omits soe oree a w r jememrmae 0 ommo rm omae pue wr jemeniome 0 con ome soe oree roes w r o oamers ewe Pe eemm Powe omen Dm remm 00000 Tamanna S TIRES ow imaman am ore seme e I fe
35. both turned on and in a Heat Cool Auto Heat or Auto Cool Mode gt Action time for this mode minutes Duration of EconoMode in minutes once started Setpoint delta increase HEAT or decrease COOL in Celsius Number of degrees Celsius that will increase in Heat Mode or decrease in Cool Mode while in EconoMode Fan Speed for this mode Fan Speed that will be set in the unit while in EconoMode 4 3 3 Enable use of ADDITIONAL HEATING mode This parameter shows hides the Contro Start Additional Heat Mode and Status Additional Heat Mode communication objects The Additional Heating Mode lets change the Setpoint Temperature and the Fan Speed within a given period of time a 37 Control Additional Heat DPT 1 010 1bit O Stop 1 Start 87 86 Status Additional Heat DPT 1 001 1bit 0 Off 1 On o If set to no the objects will not be shown o If set to yes the Control Start Additional Heat Mode and Status Additional Heat Mode objects and new parameters will appear e When a 1 value is sent to the Control communication object Additional Heating Mode will be enabled and the Status object will return this value e When a 0 value is sent to the Contro communication object Additional Heating Mode will be disabled and the Status object will return this value A Important This mode will ALWAYS turn on the indoor unit in Heat mode Action time for this mode minutes Duration of Additio
36. cialized by Mitsubishi Electric Application s Program Version 1 0 Order Code ME AC KNX 1i Intesis Software S L All rights reserved URL http www intesis com 3 63 E This information is subject to change without notice n te S i S E Email info intesis com software t IntesisBox is a registered trademark of Intesis Software SL el 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng INDEX iM Presentato a E EPRIDIU ur dUPUN IM O E Ded MUR UDRU DDR 6 2 donee EE ET e D t UMP 7 oe Conng ration and Seb ssucsaineieessstannexsaniae dax er MEO aaqeraca qa qa d RCUDEU DP A Qa dal dde dest 8 4 ELS Pal antes cs cae ree ne EAE acca tennant cece yteneeaeasetoccse M PRU 9 A C i GIAO areire I UT UTEM 10 4 1 1 Send READs for Control objects on bus recovery cc ceeee cece eect eeeeeeeeee eens 10 4 1 2 Scene to load on bus recovery startup c cece cece eee eeeeeeeee nmn nnn 10 4 1 3 Disallow control from remote controller cece cece cece eee eee ee eeeeeeeeeeeeeeeeeeaaaes 10 4 1 4 Enable func Control Lock Control Obj essen 11 4 1 5 Enable func Operating Hours Counter sssseessseseeee nennen 11 4 1 6 Enable object Error Code 2byte ceeeeernnnnnnn m Hmmm nnnm 12 4 1 7 Enable object Error Text Code 14byte eeeerneernn nm nn nnnm 12 4 2 Mode Configuration dialog sssssseeessseeeeeennn nennen 13 4 2 1 indoor uni
37. ck the remote controller because the initial scene has priority over the Control Lock Remote Control communication object 4 1 4 Enable func Control Lock Control Obj This parameter shows hide the Contro Lock Control Obj communication object which depending on the sent value locks or unlocks ALL the Contro communication objects except itself 2 34 Control Lock Control Objects DPT 1 002 bit 0 Unlocked 1 Locked o If set to no the object will not be shown o If set to yes the Control Lock Control Objects object will appear e When a 1 value is sent to this communication object all the Control objects will be locked To unlock a 0 value must be sent as the gateway remembers the last value received even if a KNX bus reset failure happens 4 1 5 Enable func Operating Hours Counter This parameter shows hides the Status_ Operation Hour Counter communication object which counts the number of operating hours for the ME AC KNX 1i 2 88 Status Operation Hour Counter DPT 7 001 2byte Number of operating hours o If set to no the object will not be shown Intesis Software S L All rights reserved URL http www intesis com 11 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng o If set to yes
38. d trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 ETS Parameters When imported to the ETS software for the first time the gateway shows the following default parameter configuration Device 1 1 1 ME AC Interface General Download latest database entry for this http www intesis com Mode Configuration product and its User Manual from special Modes Configuration Fan Speed Configuration send READs for Control objects on bus No Vanes Up Down Configuration recovery T amp U flags must be active Temperature Configuration scene to load on bus recovery startup none Scene Configuration needs to define vals for that scene i switch Off Timeouts Configuration Disallow control from remote controller No Binary Input 1 Configuration Binary Input 2 Configuration gt Enable comm obj Ctrl Remote Lock Na Binary Input 3 Configuration Binary Input 4 Configuration Enable func Control Lock Control Obj No Enable func Operating Hours Counter No Enable object Error Code 2byte No Enable object Error Text Code 14byte Yes 4 ASCII char Error Code Figure 4 1 Default parameter configuration With this configuration it s possible to send On Off Control On Off change the AC Mode Control Mode the Fan Speed Control Fan Speed and also the Setpoint Temperature Control Setpoint Temperature The Status objects
39. dard connector red grey of the interface respect polarity Reconnect power of the KNX bus o Connections diagram AC indoor unit Potential free binary inputs Internal control board l l l l l CN92 i 2 or i pelo c e cnios LI i n A Connection cable supplied with the interface KNX TP 1 EIB bus Figure 2 2 Connection diagram Intesis Software S L All rights reserved URL http www intesis com 7 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 3 Configuration and setup This is a fully compatible KNX device which must be configured and setup using standard KNX tool ETS ETS database for this device can be downloaded from http www intesis com down eib ME AC KNX 1i zip Please consult the README txt file located inside the downloaded zip file to find instructions on how to install the database A Important Do not forget to select the correct settings of AC indoor unit being connected to the ME AC KNX 1i This is in Parameters of the device in ETS Intesis Software S L All rights reserved URL http www intesis com 8 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registere
40. e e saa moen am ome Due De R ft m sous meca abe omen nom faf D m sennor tee comme noma faf f a 62 Status_ Status_ Mode Text Text 14 14 byte DPT_String_8859_1 16 001 R D ASCII String Status Fan Speed 2 Speeds 1 byte DPT Scaling 5 001 IE 50 Speed 1 100 Speed 2 Status Fan stotus_Fan Speed 2 Speeds 2 Speeds 1 byte DPT Enumerated 5 010 wp 1 Speed 1 2 Speed 2 33 Speed 1 67 Speed 2 Status Fan Speed 3 Speeds 1 byte DPT Scaling 5 001 wp 100 Speed 3 Status Fan Speed 3 Speeds 1 byte DPT Enumerated 5 010 EHE 1 Speed 1 2 Speed 2 3 Speed 3 Intesis Software S L All rights reserved URL http www intesis com 60 63 This information is subject to change without notice n tesi IS E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL software tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r1 eng Status Fan Speed 4 Speeds 1 byte DPT Scaling 5 001 Status Vanes U D 4 pos 1 byte DPT Scaling 5 001 Status Vanes U D 4 pos 1 byte DPT Enumerated 25 Speed 1 50 Speed 2 75 Speed 3 100 Speed 4 1 Speed 1 2 Speed 2 3 Speed 3 4 Speed 4 eo 0 Manual 1 Auto Fan is in speed 1 p Fan is in speed 2 p 1 Fan is in Speed 3 a 1 Fan is in Speed 4 ASCII String 25 Posi 50 Pos2 75 Pos3 100 Pos4 1 Posi 2 Pos2 3 Pos3 4
41. e Configuration see docum for your indoor unit Switch Off Timeouts Configuratior 4 DPT object type for Vanes Up Down Enumerated DPT 5 010 Binary Input 1 Configuration Binary Input 2 Configuration Enable use of object for Vanes U D No z Binary Input 3 Configuration a Binary Input 4 Configuration Enable use of bit type Vanes U D objects No z for Control Enable use of bit type Vanes U D objects No x for Status J X E Enable Vanes U D Swing objects No 7 for Control and Status Enable use of Text object for Vanes U D No Enable use of Legacy object for Vanes No x compatible with old vers of XXACKNX1 Figure 4 18 Vanes Up Down Configuration dialog All the parameters in this section are related with the Vanes Up Down properties and communication objects 4 5 1 Indoor unit has U D Vanes This parameter lets choose if the unit has Up Down Vanes available or not Indoor unit has U D Vanes Yes see docum for your indoor unit Figure 4 19 Parameter detail o If set to no all the parameters and communication objects for the Up Down Vanes will not be shown o If set to yes all the parameters and communication objects if enabled in the parameters dialog for the Up Down Vanes will be shown Intesis Software S L All rights reserved This information i
42. e indoor unit when the scene is executed The following options are available AUTO HEAT COOL FAN if available DRY or unchanged gt Scene x Value for Fan Speed if available This parameter lets choose the fan speed of the indoor unit when the scene is executed The following options are available FAN SPEED AUTO if available FAN SPEED 1 FAN SPEED 2 FAN SPEED 3 if available FAN SPEED 4 if available or unchanged gt Scene x Value for Vane U D if available This parameter lets choose the vane position of the indoor unit when the scene is executed The following options are available VANES U D AUTO if available VANES U D POS 1 VANES U D POS 2 VANES U D POS 3 VANES U D POS 4 VANES U D POS 5 if available VANES U D SWING or unchanged gt Scene x Value for Setp Temp C This parameter lets choose the setpoint temperature of the indoor unit when the scene is executed The following options are available from 19 C to 28 C both included or unchanged gt Scene x Value for Remote Lock This parameter lets choose the remote controller status of the indoor unit when the scene is executed The following options are available locked unlocked or unchanged A Important If any preset value is configured as unchanged the
43. esisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 2 4 Enable use of object for Mode This parameter shows hides the Control Mode communication object which lets change the indoor unit mode by using two different datapoint types B 10 Control Mode DPT 1 007 1bit 0 Decrease 1 Increase o If set to no the object will not be shown o If set to yes the Control Mode object and a new parameter will appear Enable use of object for Mode yes gt DPT type for Mode Object 0 Up 1 Down DPT 1 008 m Figure 4 7 Parameter detail gt DPT type for Mode Object This parameter lets choose between the datapoints O Up 1 Down DPT 1 008 and O Decrease 1 Increase DPT_1 007 for the Contro Mode object The sequence followed when using this object is shown below AUTO 2 HEAT 4 COOL Z FAN DRY E Up Increase Down Decrease A Important Read the documentation of your indoor unit to check if it has FAN mode available 4 2 5 Enable use of bit type Mode objects for control This parameter shows hides the bit type Control Mode objects 2 5 Control Mode Auto DPT 1 002 1bit 1 Set AUTO mode 2 6 Control Mode Heat DPT 1 002 1bit 1 5et HEAT mode 877 Control Mode Cool DPT 1 00 1bit 1 Set COOL mode 2 amp Control Mode Fan DPT 1 002 1bit 1 Set FAN mode af 9 Control Mode Dry DPT 1 002 1bit 1 Set DRY mode o If set
44. eter lets choose between the datapoints O Open 1 Closed Window DPT 1 009 and O Stop 1 Start Timeout DPT 1 010 for the Control Switch Off Timeout gt Disallow On Off operation while window is Open If set to no On Off commands while the window is open will be accepted e Ifa 1 value is sent to the Contro Switch Off Timeout object the switch off timeout period will begin again e If a O value is sent to the Control Switch Off Timeout object no action will be performed If set to yes On Off commands while the window is open will be saved but not applied These commands will be used in the next parameter if set to yes Reload last On Off val once window is closed If set to no once the switch off timeout is stopped any value will be reloaded If set to yes once the switch off timeout is stopped the last On Off value sent will be reloaded e If a 1 value is sent to the Control Switch Off Timeout object after the timeout period the indoor unit will turn on e If a O value is sent to the Control Switch Off Timeout after the timeout period no action will be performed 4 8 2 Enable use of Occupancy function This parameter shows hides the Control Occupancy communication object which lets apply different parameters to the indoor unit depending on the presence no presence in the room a 31 Control Occupancy DPT 1 018 1bit 0 Not Occupied 1 Occupied o If set to no the object will
45. execution of this scene will not change current status of this feature in the AC unit A Important When a scene is executed Status Current Scene object shows the number of this scene Any change in previous items does Status Current Scene show No Scene Only changes on items marked as unchanged will not disable current scene Intesis Software S L All rights reserved URL http www intesis com 38 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 48 Switch Off Timeouts Configuration dialog Device 1 1 1 ME AC Interface General l l E Enable use of Open Window Switch off No x Mode Configuration TET PO Special Modes Configuration Fan Speed Configuration Enable use of Occupancy function No Vanes Up Down Configuration i N x Temperature Configuration Enable use of Sleep function o Scene Configuration Switch Off Timeouts Configuration Binary Input 1 Configuration Binary Input 2 Configuration Binary Input 3 Configuration Binary Input 4 Configuration Figure 4 34 Default Switch Off Timeouts Configuration dialog Al the parameters in this section are related with the timeout properties and communication objects 4 8 1 Enable use of Open Window Switch off timeout function This parameter shows h
46. for fanspeed cesses nnnm nnnm rana 22 4 4 5 Enable use of object for Fan Speed csseeseeeenn mme 23 4 4 6 Enable Fan Speed Manual Auto objects for Control and Status 24 4 4 7 Enable use of bit type Fan Speed objects for Control esse 24 4 4 8 Enable use of bit type Fan Speed objects for Status eeeeeeese 25 4 4 9 Enable use of Text object for Fan Speed esee mmm 25 4 4 10 Enable use of Legacy object for Fan Speed eeeeennmm n 26 4 5 Vanes Up Down Configuration dialog sssseeeeeeeene nnnm 26 4 5 1 indoor unit has UD Valle sexoedtutatessqu bxmdawSaa VAN dd qua ato qa EVI VLFA Gi I 26 4 5 2 Available positions in Indoor Unit cc cece cece eeeeeee eee eeeeeeeeeseeeeeeeeeeeesaaaes 27 4 5 3 Indoor unit has AUTO Vanes U D ssssseseeee nennen nnn nnn 27 4 5 4 DPT object type for Vanes Up Down ceeeeen nennen menn 27 4 5 5 Enable use of object for Vanes U D cccccccseceeeeeeeeeeeeeeeeeeeeeeeensegeeneens 28 4 5 6 Enable use of bit type Vane U D objects for Control eeeeese 29 4 5 7 Enable use of bit type Vane U D objects for Status eeeeeeeeeee 30 4 5 8 Enable Vanes U D Man Auto objects for Control and Status 30 4 5 9 Enable Vanes U D Swing objects for Control and Status 31 4
47. he Status object will return this value A Important This mode will ALWAYS turn on the indoor unit in Cool mode Action time for this mode minutes Duration of Additional Cooling Mode in minutes once started Setpoint temp for this mode 9C Setpoint temperature that will be applied while in Additional Cooling Mode Fan Speed for this mode Fan Speed that will be set in the unit while in Additional Cooling Mode Intesis Software S L All rights reserved s URL http www intesis com 20 63 This information is subject to change without notice n te S i S E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 44 Fan Speed Configuration dialog Device 1 1 1 ME AC Interface General Mode Configuration Special Modes Configuration Fan is accessible in Indoor unit Yes x see docum for your indoor unit l ha dg Fan Speed Configuration Available fanspeeds in Indoor Unit Vanes Up Down Configuration see docum for your indoor unit Temperature Configuration Indoor unit has AUTO fan speed No z Scene Configuration see docum for your indoor unit Switch Off Timeouts Configuration DPT object type for fanspeed Scaling DPT 5 001 Binary Input 1 Configuration pixel a soe Scaling DPT_5001 v Binary input 2 Configuration Enable use of object for Fan Speed No
48. he byte type object a value from O to 4 has to be sent correponding each one to a different scene i e 0 Scene 1 4 Scene 5 4 7 2 Scenes can be stored from KNX bus This parameter shows hides the Control Save Exec Scene and all the Control Store Scene if enabled communication objects g 39 Control Save Exec Scene DPT 18 001 1byte 0 4 Exec1 5 128 132 Savel 5 a 40 Control Store Scene 1 DPT 1 002 lbit 1 Store Scene 1 8241 Control Store Scene 2 DPT 1 002 1bit 1 Store Scene 2 2242 Control Store Scene 3 DPT 1 002 1brt 1 Store Scene 3 8243 Control Store Scene 4 DPT 1 00 lbit 1 Store Scene 4 8224 Control Store Scene 5 DPT 1 002 1bit 1 Store Scene 5 o If set to no the communication objects will not be shown o If set to yes the communication objects and a new parameter will appear To store a scene through the byte type object a value from 128 to 132 has to be sent to the object correponding each one to a different scene i e 128 Scene 1 132 Scene 5 Scenes can be stored from KMX bus yes gt Enable use of bit objects yes for storing scenes from bus uu M J Figure 4 30 Parameter detail gt Enable use of bit objects for storing scenes from bus If set to no the objects will not be shown If set to yes the Control Store Scene objects for storing scenes will appear To store a scene by using these objects a
49. ice does not provide individual control on the internal parts of the indoor unit as can be its compressor refrigerant valves etc Rather it provides the same level of control as a user remote controller e Objects Control Mode Cool amp On and Control Mode Heat amp On intend to bring compatibility between thermostats oriented to the control of custom heating cooling systems and ready made AC indoor units by applying the following logic e Whenever a non zero value gt 0 is received at Control Mode Cool amp On indoor unit will switch On in COOL mode e Whenever a non zero value gt 0 is received at Control Mode Heat amp On indoor unit will switch On in HEAT mode e Lastest updated object will define the operating mode e Indoor unit will switch off only when both objects become zero 0 or when an OFF is requested at object 0 On Off DPT 1 001 1bit A Important These objects function is only to send On Off and Cool Heat to the indoor unit The PID Inverter system is calculated by the indoor unit itself Please consider introducing an appropriate PID configuration to the external KNX thermostat to not interfere the indoor unit PID Intesis Software S L All rights reserved URL http www intesis com 14 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 Int
50. ides the Control Switch Off Timeout communication object which lets Start Stop a timeout to switch off the indoor unit a 30 Control Switch Off Timeout DPT 1 010 bit 0 Stop 1 Start a 30 Control Window Contact Status DPT 1 009 1bit 0 Open 1 Closed o If set to no the object will not be shown o If set to yes the Control Switch Off Timeout object and new parameters will appear If a 1 value is sent to this object and the indoor unit is already turned on the switch off timeout will begin If a O value is sent to this object the switch off timeout will stop Enable use of Open Window Switch off yes timeout function Ga gt AC switch off timeout min 2 gt DPT for Window Switch off timeout 0 Open 1 Clased Window DPT 1 009 gt Reload last On Off val once window no is closed gt Disallow On Off operation while yes window is Open Figure 4 35 Parameter detail gt AC switch off timeout min This parameter lets select how much time in minutes to wait before switching off the indoor unit Intesis Software S L All rights reserved URL http www intesis com 39 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng DPTfor Window Switch off timeout This param
51. ights reserved URL http www intesis com 29 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng a 20 Control Vanes U D Pos 1 DPT 1 002 lbit 1 Set Position 1 gf 21 Control Vanes U D Pos 2 DPT 1 002 Lbit 1 Set Position 2 ay 22 Control Vanes U D Pos 3 DPT 1 002 1bit 1 Set Position 3 a 23 Control Vanes U D Pos 4 DPT 1 002 lbit 1 Set Position 4 8224 Control Vanes U D Pos 5 DPT 1 002 lbit 1 Set Position 5 o If set to no the objects will not be shown o If set to yes the Control Vanes U D objects for each Position will appear To activate a Vanes Position by using these objects a 1 value has to be sent 4 5 7 Enable use of bit type Vane U D objects for Status This parameter shows hides the bit type Status Vanes U D objects 8772 Status Vanes U D Pos 1 DPT 1 00 1bit 1 Vanes in Position 1 8773 Status Vanes U D Pos 2 DPT 1 002 1bit 1 Vanes in Position Z 8774 Status Vanes U D Pos 3 DPT 1 002 1bit 1 Vanes in Position 3 8775 Status Vanes U D Pos 4 DPT 1 002 1bit 1 Vanes in Position 4 af 76 Status Vanes U D Pos 5 DPT_1 002 1bit 1 Vanes in Position 5 o If set to no the objects will not be shown o If set to yes the Status_ Vanes U D objects for each Pos
52. is com 32 63 E This information is subject to change without notice n tes i S E Email info intesis com software IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 6 2 Transmission of Status AC Return Temp This parameter lets to you choose if the AC return temperature will be sent only cyclically only on change or cyclically and on change The AC return temperature is sent through the communication object Status AC Return Temp a 60 Status AC Return Temperature DPT 9 001 2byte C Transmission of Status AC Return Temp Cyclically and on change 4 gt Status AC Return Temp periodic 180 sending time in sec dd Figure 4 27 Parameter detail Status AC Return Temp periodic sending time in sec This parameter will only be available for the only cyclically and cyclically and on change options and let s you change the interval of time in seconds from 1 to 255 at the end of which the AC return temperature is sent to the KNX bus 4 6 3 Enable use of object for Setpoint Temp This parameter shows hides the Control Setpoint Temp communication object which lets change the indoor unit setpoint temperature by using two different datapoint types 2228 Control Setpoint Temp DPT 1 007 1bit 0O Decrease l Increase o If set to no the object will not be shown o If set to
53. ith a O value after a bus recovery Also a new parameter will appear see below Intesis Software S L All rights reserved URL http www intesis com 47 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng Ee gt Sending delay after 10 bus recovery seconds Figure 4 46 Parameter detail gt Sending delay after a bus recovery seconds This parameter lets configure a delay in seconds that will be applied after a bus recovery and after which a telegram will be sent gt Mode for short long operation This parameter lets select the value that the Binary Input x will send on a rising edge contact activated for a short and a long operation e When On increase is selected the binary input will always send telegrams with a 1 value for a short operation and an increase step for a long operation e When Off decrease is selected the binary input will always send telegrams with a O value for a short operation and an decrease step for a long operation e When Toggle On Off increase decrease is selected o For the short operation the binary input will send a 1 value after a O value and viceversa o For the long operation the binary input will send
54. ition will appear When a Vanes Position is enabled a 1 value is returned through its bit type object 4 5 8 Enable Vanes U D Man Auto objects for Control and Status This parameter shows hides the Control Vanes U D Man Auto and Status_ Vanes U D Man Auto communication objects g7 19 Control Vanes U D Man Auto DPT 1 002 Lbit 0 Manual 1 Auto ge 71 Status_ Vanes U D Man Auto DPT 1 002 Lbit 0 Manual1 Aute o If set to no the objects will not be shown o If set to yes the Control_ Vanes U D Man Auto and Status_ Vanes U D Man Auto objects will appear e When a 1 value is sent to the Contro communication object Vanes Up Down will be in Auto mode and the Status_ object will return this value e When a O value is sent to the Contro communication object Vanes Up Down will be in Manual mode and the first position will be enabled The Status_ object will return this value Intesis Software S L All rights reserved URL http www intesis com 30 63 E This information is subject to change without notice n tes i S E Email info intesis com software IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng A Important When in Auto Mode the indoor unit will choose the most appropriate vane up down position but this will be shown neither in KNX nor in the remote controller 4 5 9 Enable Vane
55. l IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng gt Operation This parameter lets select the value that the Binary Input x will send on a rising edge contact activated e When Up is selected the binary input will always send telegrams with a o e When Down is selected the binary input will always send telegrams with a 1 value e When Toggle Up Down is selected the binary input will send a O value after a 1 value and viceversa Method This parameter lets select the working method for the shutter blind e When Step Move Step is selected On a rising edge contact activated a step stop telegram will be sent and will begin a time called T1 If a falling edge occurs contact deactivated during the T1 no action will be performed If the rising edge is maintained longer than T1 a move telegram will be sent and will start a time called T2 If a falling edge occurs during the T2 a step stop telegram will be sent If a falling edge occurs after T2 no action will be performed e When Move Step is selected On a rising edge a move telegram will be sent and will begin the T2 time If a falling edge occurs during the T2 a step stop telegram will be sent If a falling edge occurs after T2 no action will be performed A Important The T1 time have to be defined in the Short long operation li
56. l 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r1 eng 0 49 Speed 1 5097 8296 Speed 2 Control Fan Speed 3 Speeds 1 byte DPT Scaling 83960 10096 Speed 3 5 001 z Control_ Fan Speed 3 Speeds 1 byte DPT_Enumerated 5 010 1 byte DPT_Scaling 5 001 1 byte 1 Speed 1 2 Speed 2 3 Speed 3 11 Control Fan Speed 4 Speeds 0 37 Speed 1 38 62 Speed 2 63960 8796 Speed 3 8896 1009 Speed 4 Control Fan Speed 4 Speeds DPT Enumerated 1 Speed 1 2 Speed 2 3 Speed 3 4 Speed 4 5 010 Control Fan Speed 1 bit DPT Step 1 00 Control Fan Speed 1 bit DPT UpDown 1 00 1 byte DPT Scaling 5 001 1 byte g 0 Manual 1 Auto p 1 Set Fan Speed 1 a 1 Set Fan Speed 2 g 1 Set Fan Speed 3 g 1 Set Fan Speed 4 E 0 Decrease 1 Increase 0 Up 1 Down 0 270 2004 6204 6304 870 Control Vanes U D 4 pos 0 37 Posi 38 62 Pos2 63 87 Pos3 88 100 Pos4 Control Vanes U D 4 pos DPT Enumerated 5 010 1 Posi 2 Pos2 3 Pos3 4 Pos4 Control Vanes U D 5 pos 0 2Q0 07 AQ0 0 O0 1 byte DPT Scaling 5 001 0 29 Posi 3090 4990 Pos2 50 69 Pos3 70 89 Pos4 90 100 Pos5 s s s s spspspss 2 2 aaa TT ea ee ata Ss ae oe Intesis Software S L All rights reserved This information is subject to change without notice
57. lity pdf Intesis Software S L All rights reserved URL http www intesis com s 54 63 This information is subject to change without notice n te ex i S E Emai info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 7 Error Codes Code Description In Hexadecimal 1 Communication error between the ME AC KNX 1i gateway and the AC unit No active error Communication error with the AC unit Discharge Temperature high 0001 1102 1108 Internal thermostat detector working 49C 1110 Outdoor unit fail 1300 Pressure low 1302 Pressure high High pressure probe working 63H p NENE NEN 0001 1102 1108 110 1300 1302 High pressure error ball valve closed Super heating anomaly due to low temp of discharge TH4 Drain sensor anomaly DS Compressor pause due to excess of current initial block Compressor pause due to excess of current overload Error in the anti phase detector electronic board Radiator panel temperature anomaly TH8 Ambient temperature probe anomaly TH1 indoor unit Liquid probe anomaly TH2 Cond Evap probe anomaly TH5 IR remote control transmission error reception error IR remote control transmission error transmission error Transmission error with the indoor outdoor unit reception error Transmission error with the indo
58. llows a complete and natural integration of MITSUBISHI ELECTRIC air conditioners with KNX control systems Compatible with all Domestic and Mr Slim models commercialized by MITSUBISHI ELECTRIC Main features e Reduced dimensions quick installation e Multiple objects for control and status bit byte characters with KNX standard datapoint types e Status objects for every control available e Timeout for Open Window and Occupancy Sleep function also available e Control of the AC unit based in the ambient temperature read by the own AC unit or in the ambient temperature read by any KNX thermostat e AC unit can be controlled simultaneously by the IR remote control of the AC unit and by KNX e Total Control and Monitoring of the AC unit from KNX including monitoring of AC unit s state of internal variables running hours counter for filter maintenance control and error indication and error code e Up to 5 scenes can be saved and executed from KNX fixing the desired combination of Operation Mode Set Temperature Fan Speed Vane Position and Remote Controller Lock in any moment by using a simple switching e Four potential free binary inputs provide the possibility to integrate many types of external devices Also configurable from ETS they can be used for switching dimming shutter blind control and more Intesis Software S L All rights reserved URL http www intesis com 6 63 E This information i
59. lue cyclically Also a new parameter will appear see below e When Never is selected cyclical sending will be disabled Period for cyclical sending seconds This parameter lets configure a time in seconds for the cyclical sending I gt Period for cyclical sending seconds Pd E Figure 4 44 Parameter detail o When Dimming is selected the communication objects and new parameters for the Input x will appear as shown below 28722 Status In2 Dimming On Off DPT 1 001 1bit 0 Off1 On 2223 Status In2 Dimming Step 5 DPT 3 007 Abit Dimming step gt Function Dimming gt Send telegram after No action bus recovery gt Mode for short long operation Toggle On Off increase decrease gt Increasing step E gt Decreasing step cL gt Short long operation limit 10 x100ms Cyclical sending period x100ms 0 4 0 Mo cyclical sending Figure 4 45 Parameter detail Send telegram after bus recovery This parameter lets select if the Binary Input x will send a telegram or not after a bus recovery and the type of telegram sent if enabled e When No action is selected no telegram will be sent after a bus recovery e When On is selected the binary input will send a telegram with a 1 value after a bus recovery Also a new parameter will appear see below e When Off is selected the binary input will send a telegram w
60. mit x100ms parameter Also the T2 time have to be defined in the Vanes adjustment time x100ms parameter Short long operation limit x100ms This parameter lets introduce the time period difference for the short and the long operation T1 time gt Vanes adjustment time x100ms This parameter lets introduce the time period for the vanes adjustment blind movement T2 time o When Value is selected the communication objects and new parameters for the Input x will appear as shown below my 97 Status In4 Value DPT 5 010 byte 1 byte unsigned value Intesis Software S L All rights reserved URL http www intesis com 50 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng gt Function Value gt Send telegram after Fixed value bus recovery D ELM MESE gt Sending delay after 10 bus recovery seconds DPT to be sent DPT 5 010 1byte gt Value on raising edge 234 when contact activated Figure 4 49 Parameter detail gt Send telegram after bus recovery This parameter lets select if the Binary Input x will send a telegram or not after a bus recovery and the type of telegram sent if enabled e When No action is selected no telegram will be sen
61. mit C This parameter lets to define the lower limit for the setpoint temperature gt Control Set Temp Upper limit C This parameter lets to define the upper limit for the setpoint temperature A Important If a setpoint temperature above the upper defined limit or below the lower defined limit is sent through the Control_ Setpoint Temperature object it will be ALWAYS applied the limit defined A Important When limits are enabled any setpoint temperature sent to the AC even through scenes special modes etc will be limited 4 6 5 Ambient temp ref is provided from KNX This parameter shows hides the Contro Ambient Temperature communication object which lets use an ambient temperature reference provided by a KNX device af 29 Control Ambient Temperature DPT 9 001 2byte C o If set to no the object will not be shown o If set to yes the Control Ambient Temperature object will appear Meant to be enabled when you want the temperature provided by a KNX sensor to be the reference ambient temperature for the air conditioner Then the following formula applies for calculation of real Control Setpoint Temperature sent to the AC unit Intesis Software S L All rights reserved URL http www intesis com 34 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisB
62. nable use of ADDITIONAL HEATING mode No z Temperature Configuration Scene Configuration Enable use of ADDITIONAL COOLING mode No X Switch Off Timeouts Configuration Binary Input 1 Configuration Binary Input 2 Configuration Binary Input 3 Configuration Binary Input 4 Configuration Figure 4 9 Default Special Modes Configuration dialog The Special Modes can be parameterized through the ETS parameters dialog and they can be used to give extra functionality A Important When executing any of the Special Modes the real state of the indoor unit will NOT be shown in KNX A Important When the predefined time for the Special Mode is finished or a O value is sent to stop it the previous state will be recovered A Important If a value concerning On Off Mode Fan Speed or Setpoint Temperature is received from KNX while any Special Mode is running 1 the Special Mode will stop and the previous state will be recovered The value received will be also applied then A Important If a value concerning On Off Mode Fan Speed or Setpoint Temperature is modified through the remote controller the Special Mode will stop WITHOUT recovering the previous state Then the real indoor unit state will be shown in KNX including the new value received through the remote controller 4 3 1 Enable use of POWER mode This parameter shows hides the Control Power Mode and Status Power Mode communication objects The Power Mode lets change the Setpoi
63. nal Heating Mode in minutes once started Setpoint temp for this mode 9C Setpoint temperature that will be applied while in Additional Heating Mode Intesis Software S L All rights reserved URL http www intesis com 19 63 E This information is subject to change without notice n te S i S E Email infoQintesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng Fan Speed for this mode Fan Speed that will be set in the unit while in Additional Heating Mode 4 3 4 Enable use of ADDITIONAL COOLING mode This parameter shows hides the Control Start Additional Cool Mode and Status Additional Cool Mode communication objects The Additional Heating Mode lets change the Setpoint Temperature and the Fan Speed within a given period of time Pi 36 Control Additional Cool DPT_1 010 1bit 0 Stop 1 Start E 87 Status Additional Cool DPT 1 001 1bit 0 Off 1 On o If set to no the objects will not be shown o If set to yes the Control Start Additional Cool Mode and Status Additional Cool Mode objects and new parameters will appear e When a 1 value is sent to the Contro communication object Additional Cooling Mode will be enabled and the Status object will return this value e When a 0 value is sent to the Contro communication object Additional Cooling Mode will be disabled and t
64. nt Temperature and the Fan Speed within a given period of time B 35 Control Power Mode DPT 1 010 1bit 0 Stop 1 Start a 64 Status Power Mode DPT 1 001 1bit 0 Off1 On o If set to no the objects will not be shown o If set to yes the Contro _ Power Mode and Status_ Power Mode objects and new parameters will appear Intesis Software S L All rights reserved URL http www intesis com 17 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng Enable use of POWER mode yes 4 Action time for this mode minutes 2 0 permanent unlimited JF gt Setpoint delta increase HEAT or 2 0 C decrease COOL in Celsius cae Fanspeed for this mode SPEED 3 if avail i Figure 4 10 Parameter detail e When a 1 value is sent to the Control_ communication object Power Mode will be enabled and the Status_ object will return this value e When a 0 value is sent to the Control_ communication object Power Mode will be disabled and the Status_ object will return this value A Important This mode will ONLY work if the indoor unit is both turned on and in a Heat Cool Auto Heat or Auto Cool Mode gt Action time for this mode minutes Duration of Power Mode in minutes
65. of value An t can be sent through the Contro object and the value retu ed by a Status Sec A Important Read the documentation of your indoor unit to check how many fan speeds are available 4 4 5 Enable use of object for Fan Speed ds dian posui e aras cd dccem r uges se dec t fan speed by using two o differ ieai nt types 2 17 Control Fan Speed DPT 1 007 1bit 0 Decrease 1 Increase o If set to no the object will not be shown o If set to yes the Control Fan Speed object and a new parameter will appear n Speed Yes ect 0 Decrease 1 Increase DPT 1 007 l No Intesis Software S L All rights reserved URL http www intesis com 23 63 This information is subject to change without notice n te S i S E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng gt DPT type for Fan Speed Object This parameter lets choose between the datapoints O Up 1 Down DPT 1 008 and O Decrease 1 Increase DPT 1 007 for the Contro Fan Speed object gt Does sequence include fan speed AUTO This parameter lets choose if AUTO function is included yes or not no in the sequence when using Control Fan Speed object as shown in the discontinuous segment at the picture below gt Roll over Speed at upper lower limit This parameter lets choose if roll
66. oo faf fr oom 00 ae n operator rour counar rome preise 701 a rp emerteememe Status_ Current Scene 1 byte DPT SceneNumber 17 001 dm O to 4 Scene 1 to 5 63 No Scene 29 Status_ Inx reeg DPT Switch 1 001 e mem 0 Off 1 On e Status Inx Status Inx Dimming On off On Off 1 EUM DPT DPT Switch 1 1000 o o Ofji On 0 1 On 94 So Intesis Software S L All rights reserved URL http www intesis com 62 63 ans dnd B id B iid Wilhaut nolge n tesi S is E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL software tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r1 eng 1 byte unsigned value Status Inx Value 4 byte 12 001 DPT Control Dimm a 2 byte unsigned value 2 byte signed value Temperature 9C 4 byte unsigned value Status Inx Dimming Step 1 bit Dimming step Status Inx Shut Blind Move 1 bit DPT ShutterBlinds 0 Move Up 1 Move Down 0 Auto 1 Heat 2 Dry 3 Fan 4 Cool Auto 1 4 Speed 1 4 0 Auto 1 5 Pos 1 5 6 Swing Intesis Software S L All rights reserved URL http www intesis com 63 63 This information is subject to change without notice n te S i E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL software tel 34 938047134
67. or outdoor unit transmission error Error in inter connection cable in the indoor outdoor unit indoor unit number deactivated 5 min or more Error in inter connection cable in the indoor outdoor unit cabling error disconnection 6846 6846 Initial timer deactivated In case you detect an error code not listed contact your nearest Mitsubishi Electric technical support service for more information on the error meaning Intesis Software S L All rights reserved s URL http www intesis com 55 63 This information is subject to change without notice n te S i S E Email info intesis com software tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r1 eng Appendix A Communication Objects Table ow feomaovor m ors uem wfr o om ro o9 een meaeae rw orre uen wit ene oe emere ime orree sone wfe are o jemeoreeoe abe cemem none wp anew ENUCCEOIDNKEENECRENC TREE SRCUNIEE ow jemmoremoy pe oem aoee p Emecmes rm mee pue fw como nasev im orron ume fol Control Fan Speed 2 Speeds Hime omsam sone we Control Fan Speed 2 Speeds EX Intesis Software S L All rights reserved URL http www intesis com 56 63 This information is subject to change without notice Email info intesis com IntesisBox is a registered trademark of Intesis Software SL te
68. ox KNX Mitsubishi Electric A C User s manual r2 eng AC Setp Temp AC Ret Temp CKNX Amb Temp KNX Setp Temp AC Setp Temp AC indoor unit setpoint temperature AC Ret Temp AC indoor unit return temperature KNX Amb Temp Ambient temperature provided from KNX KNX Setp Temp Setpoint temperature provided from KNX As an example consider the following situation User wants 199C KNX Setp Temp User sensor a KNX sensor reads 219C KNX Amb Temp Ambient temp read by Mitsubishi system is 249C AC Ret Temp In this example the final setpoint temperature that DK RC KNX 1 will send out to the indoor unit shown in Setp Temp will become 24 C 219C 190C 220C This is the setpoint that will actually be requested to Mitsubishi Electric unit This formula will be applied as soon as the Control Setpoint Temperature and Control Ambient Temperature objects are written at least once from the KNX installation After that they are kept always consistent Note that this formula will always drive the AC indoor unit demand in the right direction regardless of the operation mode Heat Cool or Auto 4 7 Scene Configuration dialog Device 1 1 1 ME AC Interface General Enabl f Yes Mode Configuration NE Special Modes Configuration Scenes can be stored from KNX bus No x Fan Speed Configuration Vanes Up Down Configuration Enable use of bit objects No
69. parameter enables the use of the Input x and shows hides the Status Inx communication object s which will act as configured in the Function parameter 8220 Status Inl Switching DPT 1 001 1bit 0 Off1 On 822 Status In2 Switching DPT 1 001 1bit 0 Off1 On 8224 Status In3 Switching DPT 1 001 1bit 0 Off1 On a 96 Status_In4 Switching DPT_1 001 1bit 0 Off1 On o If set to no the objects will not be shown o If set to yes the Status_ Inx object s and new parameters will appear 4 9 2 Contact type This parameter lets choose the behavior that will have the binary input depending on if the contact is normally open or normally closed o There are two possible options to configure the contact type NO Normally Open and NC Normally Closed 4 9 3 Debounce time This parameter lets choose a debounce time in milliseconds that will be applied to the contact Intesis Software S L All rights reserved URL http www intesis com 44 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 9 4 Disabling function This parameter shows hides the Control Disable Input x communication object which will let disable enable the input x Pi 50 Control_ Disable Input 1 DPT 1 002
70. r This parameter allows 1 Having the remote controller always locked or 2 Decide through a new communication object if the RC is locked or not o If set to yes all the actions performed through the remote controller will be disabled Intesis Software S L All rights reserved URL http www intesis com 10 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng o If set to no the remote controller will work as usually It also appears a new parameter and the communication object Control Lock Remote Control Fad 33 Control Lock Remote Control DPT 1 002 1bit 0 Unlocked 1 Locked Disallow control from remote controller no gt Enable comm obj Ctrl Remote Lock yes Figure 4 5 Communication object and parameter detail gt Enable comm obj Ctrl Remote Lock If set to no the object will not be shown If set to yes the Control Lock Remote Control object will appear e When a 1 value is sent to this communication object the remote controller is locked To be unlocked a O value must be sent The gateway remembers the last value received even if a KNX bus reset failure happens A Important If an initial scene is enabled and it has as Value for Remote Lock unchanged or unlocked this would unlo
71. s U D Swing objects for Control and Status This parameter shows hides the Contro Vanes U D Swing and Status Vanes U D Swingo communication objects 8 75 Control Vanes U D Swing DPT 1 002 1bit 0 Off1 Swing 8777 Status Vanes U D Swing DPT 1 002 1bit 0O Off1 Swing o If set to no the objects will not be shown o If set to yes the Control Vanes U D Swing and Status Vanes U D Swing objects will appear e When a 1 value is sent to the Contro communication object Vanes Up Down will be in Auto mode and the Status object will return this value e When a O value is sent to the Contro communication object Vanes Up Down will be in Manual mode and the first position will be enabled The Status object will return this value 4 5 10 Enable use of Text object for Vane U D This parameter shows hides the Status Vanes U D Text communication object 8278 Status Vanes U D Text DPT 16 001 14byte ASCII String o If set to no the object will not be shown o If set to yes the Status Vanes U D Text object will appear Also in the parameters will be shown seven text fields five for the Vane Position and one for the Auto function and another one for the Swing function that will let modify the text string displayed by the Status_ Vanes U D Text when changing a vane position String when vanes U D in AUTO U D AUTO if available gt String when vanes U D in POS 1 U D POS 1 gt String when vanes U D in POS
72. s possible to change de DPT for the Control Vanes U D and Status Vanes U D byte type communication objects Datapoints Scaling DPT 5 001 and Enumerated DPT 5 010 can be selected A Important The communication objects shown in this section may be different depending on the number of vanes position available although they all share the same communication object number Intesis Software S L All rights reserved URL http www intesis com 27 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng o When Enumerated DPT 5 010 is selected Contro Vanes U D and Status Vanes U D communication objects for this DPT will appear Fd 18 Control Vanes U D 5 Pos DPT 5 010 1byte Position values 1 2 3 4 5 Fd 70 Status_ Vanes U D 5 pos DPT 5 010 1byte Position values 1 2 3 4 5 To choose a vanes position values from 1 to 4 or 5 when available can be sent to the Contro object Each value will correspond to the position i e Value 3 Position 3 The Status object will always return the value for the vane position selected A Important If a O value is sent to the Control object the Position 1 will be selected If a value bigger than 4 or 5 when available is sent to the Control object then the
73. s subject to change without notice URL http www intesis com 26 63 ntes i S E ER info intesis com IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng A Important Read the documentation of your indoor unit to check if Up Down Vanes are available 4 5 2 Available positions in Indoor Unit This parameter lets choose how many vane positions are available in the indoor unit Ln WE Available positions in Indoor Unit see docum for your indoor unit Figure 4 20 Parameter detail A Important Read the documentation of your indoor unit to check how many vane positions are available 4 5 3 Indoor unit has AUTO Vanes U D This parameter lets choose if the indoor unit has Auto Vanes U D available or not Indoor unit has AUTO Vanes U D Ves see docum for your indoor unit Figure 4 21 Parameter detail o If set to no all the parameters and communication objects for the Auto Vanes U D will not be shown o If set to yes a new parameter will appear Find more information on section 2 5 8 Enable Vanes U D Man Auto objects for Control and Status Enable Vanes U D Man Auto objects No for Control and Status Figure 4 22 Parameter detail A Important Read the documentation of your indoor unit to check if Auto Vane Position is available 4 5 4 DPT object type for Vanes Up Down With this parameter i
74. s subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 2 Connection The interface comes with a cable 1 9 meters long for direct connection to the internal control board of the AC indoor unit o Connection of the interface to the AC indoor unit Disconnect mains power from the AC unit Open the front cover of the indoor unit in order to have access to the internal control board In the control board locate the socket connector marked as CN92 in Mr Slim models Or CN105 in rest of models Using the cable that comes with the interface insert one of its connectors the one installed in the shortest uncovered part into the socket of the ME AC KNX 1i marked as AC Unit and the other connector the one in the largest uncovered part into the socket CN92 or CN105 of the AC unit s control board Fix the ME AC KNX 1i inside or outside the AC indoor unit depending on your needs remember that ME AC KNX 1i must be also connected to the KNX bus Close the AC indoor unit s front cover again A Important Do not modify the length of the cable supplied with the interface it may affect to the correct operation of the interface o Connection of the interface to the KNX bus Disconnect power of the KNX bus Connect the interface to the KNX TP 1 EIB bus using the KNX stan
75. speed is AUTO AUTO if available gt String when fan speed is 1 SPEED 1 String when fan speed is 2 SPEED 2 String when fan speed is 3 SPEED 3 if available gt String when fan speed is 4 SPEED 4 if available Figure 4 17 Parameter detail Intesis Software S L All rights reserved URL http www intesis com 25 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 4 4 10 Enable use of Legacy object for Fan Speed This parameter shows hides the Legacy Fan Speed communication object af 99 Legacy Fan Speed Enumerated 1byte 0 Auto 1 4 speed 1 4 o If set to no the communication object will not be shown o If set to yes the communication object will appear This object lets change the indoor unit fan speed but it uses a different data type It is used to maintain compatibility with old gateway models 45 Vanes Up Down Configuration dialog Device 1 1 1 ME AC Interface General Indoor unit has U D Vanes Yes x Mode Configuration i see docum for your indoor unit Special Modes Configuration E Fan Speed Configuration Available positions in Indoor Unit 5 Vanes Up Down Configuration see docum for your indoor unit cm Temperature Configuration Indoor unit has AUTO Vanes U D No Scen
76. t after a bus recovery e When Fixed value is selected the binary input will send a telegram with the same value configured in the Value on rising edge parameter Also a new parameter will appear see below a i gt Sending delay after 10 bus recovery seconds Figure 4 50 Parameter detail Sending delay after a bus recovery seconds This parameter lets configure a delay in seconds that will be applied after a bus recovery and after which a telegram will be sent gt DPT to be sent This parameter lets select the DPT type for the value that will be defined in the next parameter This value will be sent on a rising edge contact activated DPT to be sent DPT 12 001 4byte E Figure 4 51 Parameter detail gt Value on rising edge when contact activated This parameter lets define a value for the DTP type configured in the DPT to be sent parameter This value will be sent on a rising edge contact activated o When Execute Scene internal is selected the binary input x will activate the scene defined in the next parameter on a rising edge contact activated Intesis Software S L All rights reserved URL http www intesis com 51 63 This information is subject to change without notice n te S i S E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng
77. t i URL http www intesis com 57 63 Email info intesis com IntesisBox is a registered trademark of Intesis Software SL n esis E tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r1 eng 1 Posi 2 Pos2 3 Pos3 Control Vanes U D 5 pos 1 byte DPT Enumerated 5 010 WIT 4 Pos4 5 Pos5 a jemerwessmeus im comme pue m ememrem 000000 Dae ewe eese ie comme ue m jemeemm 000 m jew essa aoe comme puer jemeemm 0000 Lm jeecwenens am omer ume pp memes 000000 convas oroa see omms re wlr esemmer 0000 D eee never roe mes um wla firsernes 00 Las ewe vn vsere rm comme puer je emem 700000 emecwesss see mmm som u ewemeraeme 000 La comer seantrermenee zone ore mo mr feo bmc ne mme roor fw jesemereme 0000 La jemeomeneeemes we emomeme wn wir feo be wnan connessa re mee rom wlr o oo cono smen ormon ne ms uee wp jemmrsm 000000 m jewerenens ie sow ime w e poeememic mme Dm eam seem ie mx ro wm jemerme 000 Lm jemereeseeecees aoe comme pue wp jewemsiume 000 Intesis Software S L All rights reserved URL http www intesis com 58 63 This information is subject to change without notice n tesi IS E Email info intesis com IntesisBox is a registered trademark of Intesis Software SL software tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r1 eng 34 Control Lock Control O
78. t nas FAN TTIOGG iiceservvuxa uxsassrr tduwieesztirvUrvboea tura da n ERR ba E adwaa Vx xa er ai 13 4 2 2 Enable use of Heat Cool bit type obj ceeeeeeeenennn mmm 13 4 2 3 Enable PID Compat Scaling Mode Objects ceseeeeenn nmm nnn 14 4 2 4 Enable use of object for Mode ssssssseeen Hmmm enn nns 15 4 2 5 Enable use of bit type Mode objects for control eeeeeeeeeeeeeee 15 4 2 6 Enable use of bit type Mode objects for status eene 16 4 2 7 Enable use of Text object for Mode ssseseeeseeeee nnn nnne 16 4 2 8 Enable use of Legacy object for Mode eeeesseeenn nn nnnm 16 4 3 Special Modes Configuration dialog csssseseeeeeennn nen mnnera 17 4 3 1 Enable use of POWER mode eese mnnera nna 17 4 3 2 Enable Use of ECONOMY Ode srissurkiRERCr rn a i YIFPEENEE Toa C Xa EYEERSQ OPI I YN Sx UE 18 4 3 3 Enable use of ADDITIONAL HEATING mode eene nnn 19 4 3 4 Enable use of ADDITIONAL COOLING mode enn 20 4 4 Fan Speed Configuration dialog sse asd kd x6 iura cid crd ExTED ga E Pac ac uw Ed EE EV E dI EY Va Ee UA 21 4 4 1 Fan is accessible in Indoor unit eeeeeseeeieeeeee nennen nnnm 21 4 4 2 Available fanspeeds in Indoor Unit eeeseessseeeee nmm 21 4 4 3 Indoor unit has AUTO fan speed sudotumbeditex ima ves esum Rawfrtbs qu DES ODLDIOE maaa qa 6t 22 4 4 4 DPT object type
79. tion dialog esses nnn 39 4 8 1 Enable use of Open Window Switch off timeout function eeeeeee 39 4 8 2 Enable use of Occupancy function seeeeeeesseeeen ehe 40 4 8 3 Enable use of SLEEP tilmeoLlE sscix xa aser exor cca dace sbbora a Kobeieg bx acp a E baci 43 4 9 Binary Input x Configuration dialog sssseseeeeeeeennn heme 44 4 9 1 Phebe Use of INDUL X aotaesxuiereterPuvIMMEEESUPRVPT TIR ME FU PIDUFELUIATE MICE DRE EDI EE NUE 44 4 9 2 Gelato dir RR m 44 4 9 3 Debounce time auasiectiiat pea pie usd aX EaREVICx FER Padoafsbe Er Cor EeTFENUCE ED RIA ESUPEUEE 44 4 9 4 Bit zjeigremddisreidien NR TTE TETTE 45 4 9 5 gigsuier TP T 45 5 SPECICATION eerie i passa pe aurades CIS EP SPP E IN FO DEUM ssearinenetiasesasias 53 6 AC Unit TVBescormpartibIllE sovsansawsecausenwanausaccencansutiessanaeyeueniiaaaiweeseeaasesarnaeaen 54 7 go COO TT UU TUI ee ere ere 55 Appendix A Communication Objects Table ccccccccccceeseeeeee eens ee nhe nnn nnn 56 Intesis Software S L All rights reserved URL http www intesis com 5 63 E This information is subject to change without notice n te S i S E Email info intesis com i tel IntesisBox is a registered trademark of Intesis Software SL m 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng 1 Presentation ME AC KNX 1i a
80. to no the objects will not be shown Intesis Software S L All rights reserved URL http www intesis com 15 63 E This information is subject to change without notice n te S i S E Email info intesis com tel IntesisBox is a registered trademark of Intesis Software SL 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng o If set to yes the Contro Mode objects for Auto Heat Cool Fan and Dry will appear To activate a mode by using these objects a 1 value has to be sent 4 2 6 Enable use of bit type Mode objects for status This parameter shows hides the bit type Status Mode objects a 5 Status Mode Auto DPT 1 002 1bit 1 AUTO mode is active 7 58 Status Mode Heat DPT 1 002 1bit 1 HEAT mode is active a 59 Status Mode Cool DPT 1 002 1bit 1 COOL mode is active a 60 Status Mode Fan DPT 1 002 1bit 1 FAN mode ts active a 61 Status_ Mode Dry DPT 1 002 1bit 1 DRY mode is active o If set to no the objects will not be shown o If set to yes the Status Mode objects for Auto Heat Cool Fan and Dry will appear When enabled a mode will return a 1 through its bit type object 4 2 7 Enable use of Text object for Mode This parameter shows hides the Status Mode Text communication object E 62 Status Mode Text DPT 16 001 14byte ASCI String o If set to no the object will not be shown o If set to yes the Status Mode
81. tus Mode Cool Heat objects will appear Intesis Software S L All rights reserved URL http www intesis com 13 63 E This information is subject to change without notice n tes i S E Email info intesis com software IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng e When a 1 value is sent to the Contro communication object Heat mode will be enabled in the indoor unit and the Status object will return this value e When a 0 value is sent to the Contro communication object Cool mode will be enabled in the indoor unit and the Status object will return this value 4 2 3 Enable PID Compat Scaling Mode Objects This parameter shows hides the Contro Mode Coo amp On and Control Mode Heat amp On communication objects Fd 3 Control Mode Cool amp On DPT 5 001 1byte O Off0 1 100 On Coal ae 4 Control Mode Heat amp On DPT 5 001 byte 0 Off 0 1 100 On Heat o If set to no the objects will not be shown o If set to yes the Control Mode Cool amp On and Control Mode Heat amp On objects will appear e These objects provide compatibility with those KNX thermostats that control the demand of heating or cooling by using scaling percentage objects In these thermostats the percentage demand is meant to be applied on a fluid valve of the heating cooling system e ME AC KNX 1i dev
82. v Temperature Configuration for scene execution Scene Configuration Scene 1 preset No Switch Off Timeouts Configuration c 0 0 iC P C 2 00 B Binary Input 1 Configuration Scene 2 preset No x Binary Input 2 Configuration Binary Input 3 Configuration Scene 3 preset No M Binary Input 4 Configuration Scene 4 preset No Scene 5 preset No x Figure 4 28 Parameter detail All the parameters in this section are related with the Scene properties and communication objects A scene contains values of On Off Mode Fan speed Vane position Setpoint Temperature and Remote Controller Disablement 4 7 1 Enable use of scenes This parameter shows hides the scene configuration parameters and communication objects a 39 Control Execute Scene DPT_18 001 1byte 0 4 Execute Scene 1 5 Intesis Software S L All rights reserved URL http www intesis com 35 63 E This information is subject to change without notice n tes i S E Email info intesis com software IntesisBox is a registered trademark of Intesis Software SL tel 34 938047134 IntesisBox KNX Mitsubishi Electric A C User s manual r2 eng Enable use of scenes yes r Figure 4 29 Parameter detail o If set to no the scene parameters and communication objects will not be shown o If set to yes the scene parameters and communication objects will be shown To execute a scene through t
83. x Binary Input 3 Configuration Binary Input 4 Configuration Enable use of bit type Fan Speed objects No z for Control eT Enable use of bit type Fan Speed objects No z for Status Enable use of Text object for Fan Speed No Enable use of Legacy_ object for Fan No x compatible with old vers of XXACKNX1 Figure 4 11 Default Fan Speed Configuration dialog Al the parameters in this section are related with the Fan Speed properties and communication objects 4 4 1 Fanis accessible in Indoor unit This parameter lets choose if the unit has Fan Speed control available or not Fan is accessible in Indoor unit Yes see docum for your indoor unit Figure 4 12 Parameter detail o If set to no all the parameters and communication objects for the Fan Speed will not be shown o If set to yes all the parameters and communication objects if enabled in the parameters dialog for the Fan Speed will be shown A Important Read the documentation of your indoor unit to check if Fan Speed control is available 4 4 2 Available fanspeeds in Indoor Unit This parameter lets choose how many fan speeds are available in the indoor unit xj 2 Available fanspeeds in Indoor Unit see docum for your indoor unit Figure 4 13 Parameter detail A Important Read the documentation of your indoor unit to check how many fan speeds are available Intesis Software S L

IntesisBox ME-AC-KNX-1i v1.0

Contents

Download Pdf Manuals

Related Search

Related Contents