Home

INT-TSH

image

Contents

1. least 10 minutes the authorization screen can be displayed Enter the code to be able to disarm the partition The keypad can be configured by the installer so as to display the macro commands assigned to a corresponding group on tapping the corner of status screen The illustration below shows the screen parts the tapping of which can display macro commands the digit corresponds to the number of macro command group Icons of macro command groups can be displayed there 4 INT TSH SATEL 21 07 2015 10 54 37 Status screen background A single picture or a slide show can be displayed as the status screen The status screen background is to be configured by the installer 1 1 4 Main screen Presented on the main screen are e date and time in the format defined by the installer if some specific events occur other messages can be displayed instead of the date and time e g entry or exit delay countdown alarm messages etc e name of the currently logged user icons enabling operation of the keypad and alarm system Icon Function Informs you that no user is logged in User login Informs you that a user is logged in name of the currently logged user is displayed below User logout a Displays the Arming screen see pages 6 and 14 Gi o SATEL INT TSH 5 Enables disarming alarm clearing see pages 6 16 and 17 Enables control of the alarm system and home automation devices see p 7 Displays
2. screen on which the current troubles are presented the installer can configure the control panel to display the troubles until cleared Enables viewing the event log Displays the Alarm log screen on which alarms stored in the control panel memory are presented Displays the Trouble log screen on which troubles stored in the control panel memory are presented SATEL INT TSH 9 When viewing the log of events alarms or troubles the a icon is available at the top of the screen Tapping the icon will toggle the information presentation mode light grey color font and the other way round Partition status The status of partitions is illustrated by means of icons Tap the icon situated at the top of the screen to see description of all icons The number shown next to the icon corresponds to the partition number On tapping the icon the full partition name will be presented at the display bottom Icon Partition status disarmed there are no violated zones disarmed there are violated zones armed mode full armed mode full bypasses armed mode without interior armed mode without interior and without entry delay CG temporarily blocked entry delay countdown is running fire alarm alarm fire alarm memory alarm memory VO DOG Zone status The status of zones is illustrated by means of icons The icons are designated by numbers corresponding
3. the System status screen see p 8 Displays the Emergency screen see p 10 Displays the Advanced screen see p 11 1 1 5 Authorization screen Enter the code Some screens and functions may only be available after user authorization The authorization is code based Use the number keys to enter the code and then confirm tapping the icon By default the following codes are preprogrammed in the control panel service code 12345 object 1 master administrator code 1111 lf you make a mistake when entering the code tap x and re enter the code if you fail to enter the valid code within one minute information on entering a wrong code will be saved to the control panel memory 6 INT TSH SATEL 1 1 6 Arming screen Icon Function Enables arming in mode full Enables arming in mode full bypasses Enables arming in mode without interior Enables arming in mode without interior and without entry delay Alarm clearing Disarming SATEL INT TSH T The Alarm clearing Disarming screen will be displayed after you tap the Zu icon on the main screen when there is an alarm alarm memory and at least one partition is armed Icon Function H Enables alarm clearing 7 Enables disarming ali 1 1 8 Control screen The Control screen will be displayed on tapping the A icon on the main screen if macro commands are assigned to at l
4. to the zone numbers On tapping the icon the zone number and text information about the zone state is presented at the top of the display 10 INT TSH SATEL Zone status normal violated N trouble long violation trouble no violation bypassed e N tamper alarm alarm tamper alarm memory alarm memory tamper masking masking memory 1 1 10 Emergency screen Emergency INT TSH 11 Function Tapping and holding for 3 seconds will trigger the fire alarm Tapping and holding for 3 seconds will trigger the medical auxiliary alarm Tapping and holding for 3 seconds will trigger the panic alarm The installer defines whether the loud panic alarm with a loud alarm signal or the silent one without a loud signal will be triggered 1 1 11 Advanced screen LE WE la L LL LL E gt 2 P In the lower right corner of the screen you will find information on the keypad firmware version Icon Function Locking the touch screen for 30 seconds to clean the screen Displays the Backlight screen Displays the Volume screen Enables updating of the keypad firmware the function is available after entering the service code Enables formatting of the microSD card the function is available after entering the service code Displays the terminal 12 INT TSH SATEL Backlight Backlight O 60 22 00 6 00 Intensity of the screen backlight ca
5. Sako int tsh oi en 10 15 Keypad INT TSH Firmware version 1 00 INTEGRA INTEGRA Plus Brief System User Manual SATEL sp z 0 0 ul Budowlanych 66 80 298 Gdansk POLAND tel 58 320 94 00 www satel eu WARNINGS Please read this manual carefully before use Changes modifications or repairs not authorized by the manufacturer shall void your rights under the warranty Warning This is a Class A product In a domestic environment this product may cause radio frequency interference in which case the user may be required to take adequate measures The installer manual contains information on how to minimize the radio interference SATEL s goal is to continually upgrade the quality of its products which may result in alterations of their technical specifications and firmware The current information on the introduced modifications is available on our website Please visit us http www satel eu The declaration of conformity may be consulted at www satel eu ce The following symbol may be used in this manual note We are pleased that you have chosen a product offered by us We wish you satisfaction with your choice and would like to assure you that we are always ready to provide professional assistance and information on our products SATEL Ltd is a manufacturer of a wide variety of dedicated devices for use in alarm systems Additional information can be found on our website www satel eu or
6. arming procedure was started there is a trouble which did not exist when the arming procedure was started 2 2 Disarming If there is an alarm alarm memory disarming will result in simultaneously clearing the alarm d Tap e on the main screen Depending on the system state There is no alarm alarm memory and 1 partition is armed you have access to 1 partition The partition will be disarmed ll There is an alarm alarm memory and 1 partition is armed you have access to 1 partition The Alarm clearing Disarming screen will be displayed Tap ri The partition will be disarmed lll There is no alarm alarm memory and at least 2 partitions are armed The selection screen will be displayed Viv Vivi Tap ww if you want to disarm all partitions to which you have access from the keypad SATEL INT TSH 17 v Tap wv if you want to select the partitions which are to be disarmed The screen showing the partitions by means of suitably described fields will be displayed Tap a field to select the partition The V icon will be displayed in the field the full partition name will appear at the bottom of the screen When you finish selecting the partitions tap V to disarm them IV There is an alarm alarm memory and at least 2 partitions are armed af The Alarm clearing Disarming screen will be displayed Tap iri and then follow the instructions given in it III above 2 3 Alarm
7. at points of sale offering our products 1 Keypad description The touch screen displays information about the system status while allowing you to operate and program the alarm system as well as control the home automation equipment Intuitive icon based menu makes the everyday use easier The keypad offers two operating modes e graphical mode large icons are displayed without description e verbose mode small icons are displayed with description To change the operating mode use the following icons 7 tap to switch over the screen to the verbose mode amp tap to switch over the screen to the graphical mode This manual describes how to operate the keypad based on the graphical mode Tapping an icon or icon description will display the next screen or start the specified function The icon will bring you back to the previous screen Tapping the gt icon will display the main screen After the keypad is idle for 10 minutes the screen can either go blank or a slide show or the clock can be displayed Tapping the screen when it is blank or the slide show or the clock is displayed will wake up the keypad The keypad can also be woken up e g on opening the door detecting motion by a detector etc The installer defines the content which is to be displayed after the keypad wake up status screen main screen or start of the disarming procedure 2 INT TSH SATEL Tapping and holding the screen for 3 seconds will tri
8. clearing without disarming P Tap e on the main screen Depending on the system state There is an alarm alarm memory and none of the partitions is armed The alarm will be cleared II There is an alarm alarm memory and at least 1 partition is armed The Alarm clearing Disarming screen will be displayed Tap Ni The alarm will be cleared 2 4 Viewing the event log 2 4 1 Viewing all events 1 Tap i on the main screen The System status screen will be displayed 2 Tap SCH The Event og screen will be displayed Viv Viv 3 Tap Vivi The last three events stored in the control panel memory will be displayed The icon allows you to view previous events 2 4 2 Viewing the selected events i 1 Tap on the main screen The System status screen will be displayed 2 Tap SS The Event log screen will be displayed vV 3 Tap wv The Event log selected screen will be displayed 4 Tap The screen presenting event types will be displayed EC 18 INT TSH SATEL 5 Tap the event types which are to be shown and then tap vV You will be brought back to the previous screen on which an extra V icon will appear m 6 If only events from selected partitions are to be shown tap MW The screen showing partitions by means of suitably described fields will be displayed Tap a field to select the partition The icon will be displayed in the field the full partition name will ap
9. d execution signaling of entering the user menu submenu or function 3 short beeps signaling of starting the arming procedure there is exit delay in the partition or arming there is no exit delay in the partition disarming and or alarm clearing turning output off disabling chime signal in the keypad using the Bev key exiting the function and returning to the menu after confirmation of the data entered 14 INT TSH SATEL 4 short beeps and 1 long beep signaling of turning output on enabling chime signal in the keypad using the key ending the function and exiting the user menu after confirmation of the data entered 1 long beep signaling of violated bypassed zones when arming fault of the vibration detector 10 24H VIBRATION type zone was not violated during the vibration detector test run upon starting the arming procedure 2 long beeps incorrect code function not available or exiting the function without confirmation of the data entered e g by using the ER key 3 long beeps unavailable function 1 2 3 Events signaled by sounds Only installer selected events are signaled Alarms are being signaled throughout the time programmed by the installer 5 short beeps zone violation CHIME Long beep every 3 seconds followed by a series of short beeps for 10 seconds and 1 long beep countdown of exit delay if the time is shorter than 10 seconds only the f
10. east two groups of macro commands It presents the groups of macro commands Up to 4 groups can be programmed by the installer Tapping a group icon will display macro commands assigned to that group Up to 16 macro commands can be assigned to one group If macro commands are assigned only to one group tapping the A icon will display the macro commands at once In the keypad with factory settings two macro commands are programmed and assigned to the first group the figure below shows the screen to be displayed on a keypad with factory settings The control panel will execute the factory programmed macro commands provided that the alarm system is suitably configured by the installer You should consult the installer about which additional macro commands would facilitate operation of the alarm system or control of the home automation devices connected to the control panel Only the installer can program any additional macro commands Control 1 8 INT TSH SATEL Function Quick full arming without user authorization by using a code in a similar way as after pressing the 0 keys on the keypad with text menu Exit delay clearing in a similar way as after pressing the 9 keys on the keypad with text menu from the terminal on tapping the may be required 1 1 9 System status screen Function Displays the Partition status screen Displays the Zone status screen Displays the Troubles
11. gger a silent panic alarm If a Slide show clock or status screen is displayed the screen is blank Whether this function is to be available should be defined by the installer During the keypad inactivity period messages about arming disarming entry exit delay countdown alarm etc can be displayed on the screen 1 1 1 Status bar When a slide show clock or status screen is displayed the status bar is shown at the top of the screen Icons situated on the status bar indicate the system status Color System status yellow trouble or trouble memory green at least one partition is armed red alarm or alarm memory Icon O Been green service mode entered The information about arming may be hidden after the time defined by the installer has elapsed If the GRADE 2 INTEGRA GRADE 3 INTEGRA Plus option is enabled by the installer information about the alarm is not presented the ih icon indicates trouble trouble memory alarm alarm memory bypassed zones 1 1 2 Slide show The slide show can be displayed as the status screen background or the screensaver The pictures to be displayed should be saved to a microSD memory card which will be put into the keypad by the installer The installer defines the speed at which the pictures will change during the slide show 1 1 3 Status screen The status screen is displayed 60 seconds after the last operation performed on the keypad screen unless the ter
12. inal sequence of short beeps will be generated A sequence of 7 beeps of diminishing duration repeated every few seconds countdown of auto arming delay 2 short beeps every seconds countdown of entry delay 2 short beeps every 3 seconds signaling a new trouble Continuous beep alarm Long beep every second fire alarm 2 Operating the alarm system This section describes selected operations which can be executed using the icon based menu The description does not include the user authorization which will be required when using the keypad The alarm system is operated from the terminal in the same way as when using the LCD keypad with text menu For description of the alarm system operation by means of LCD keypad with text menu please refer to the control panel user manual 2 1 Arming Completion of the steps below will start the arming procedure The procedure ends when the exit delay time elapses if the countdown is completed successfully the system becomes armed see also Failure of arming procedure p 16 If the exit delay time is 0 the system becomes armed instantly For further information on arming arming modes etc please refer to the user manual for INTEGRA or INTEGRA Plus control panels This section describes the operations which must be performed to arm the system in the full mode To arm the system in other mode you should proceed in much the SATEL INT TSH 15 same way except that ins
13. med The installer should be consulted whether and how the quick arming will be possible The keypad factory settings allow for quick full arming in the following manner 1 Tap the upper left corner of the status screen Macro commands assigned to the first group will be displayed 2 Tap The arming procedure will begin 16 INT TSH SATEL 21 4 Denial of arming The installer can program the control panel so that the arming procedure could not be started if azone is violated in the partition there is a trouble in the system including tamper there was a verified alarm In such a case the terminal will be displayed and a message specifying the cause of refusal Additionally the message can prompt action which you can take 1 Ok on tapping the S key you will be brought back to the previous screen arming is impossible 1 Arm on tapping the key the system will be armed despite the violated zone or trouble forced arming 2 Check on tapping the key you will be able to view the list of violated bypassed zones or troubles When viewing the list of violated bypassed zones you can bypass unbypass the currently displayed zone by tapping the 4 key 2 1 5 Failure of arming procedure The installer can program the control panel so that the arming procedure will fail if when the exit delay countdown ends there is a violated zone in the partition which was not violated when the
14. minal is running see p 13 When the terminal is displayed the status screen may appear later or even not appear at all e g when the service menu Is open If the user is logged in he she will be automatically logged out a few seconds after the status screen is displayed SATEL INT TSH 3 21 07 2015 10 54 37 Additional information presented on the status screen The keypad with factory settings presents the date and time on the status screen The installer can customize the information displayed to suit the user needs Information on the state of selected partitions zones or outputs temperature taken by selected temperature detectors date and time as well as any text can be presented on the status screen Icons illustrating the state of partitions are described in section Partition status p 9 Icons illustrating the state of zones are described in section Zone status p 9 Icons illustrating the state of outputs are shown in the table below Icon Color Output status grey deactivated i red activated Additional messages connected with occurrence of specific events e g arming or disarming auto arming delay countdown entry exit delay countdown alarm etc may also appear on the status screen Functions available from the status screen Tapping the status screen will display the main screen If at least one partition operated from the keypad is armed and the keypad has not been used for at
15. n be controlled within the 10 100 range In the night hours which can be specified the backlight intensity can be different Volume Volume ni H 60 60 60 60 90 90 You can define the volume level of sounds generated SE when operating the keypad tapping the keys confirmation of performed operation etc after zone violation CHIME signal when signaling the entry delay when signaling the exit delay when signaling fire alarms e when signaling burglary panic and medical alarms SATEL INT TSH 13 Terminal Terminal ALAN The terminal enables the alarm system to be operated and programmed in the same way as from the LCD keypad with text menu The method of using such a keypad is described in the control panel programming user manuals electronic versions of the manuals are available on the www satel eu website 1 2 Sound signaling The installer can disable the sound signaling 1 21 Beeps generated when using the icon based menu 1 short beep tapping a key on the authorization screen or selecting deselecting a field when choosing the partitions and event type 2 short beeps tapping an icon 2 long beeps incorrect code function unavailable or return from the main screen back to the status screen 3 short beeps confirmation of command execution 1 2 2 Beeps generated when using the terminal 1 short beep tapping a number key 2 short beeps confirmation of comman
16. pear at PG the bottom of the screen When you finish selecting the partitions tap V It will take you back to the previous screen A 7 Tap V The last three events which are stored in the control panel memory and meet the selected criteria will be displayed The icon allows you to view previous events
17. tead of the icon for arming the system in the full mode you should tap other icon The installer can prepare macro commands to simplify the arming procedure especially for the system subdivided into many partitions 2 1 1 Full arming of all partitions ii T 1 Tap on the main screen The Arming screen will be displayed from the given keypad the partition arming procedure will start immediately Viv Vi y 3 Tap vivi The arming procedure will start in all partitions to which the user has access from the keypad 2 1 2 Full arming of selected partitions z T 1 Tap a on the main screen The Arming screen will be displayed 2 Tap a The selection screen will be displayed V 3 Tap wv The screen showing partitions by means of suitably described fields will be displayed Tap a field to select the partition The V icon will be displayed in the field the H full partition name will appear at the bottom of the screen When you finish selecting the partitions tap d The arming procedure will be initiated in the partitions If a field is tapped and held for 3 seconds icon was displayed in the field the V icon will appear in all fields if the icon will appear in all fields if the V icon was displayed in the field ef the 2 1 3 Quick arming The installer can permit arming without entering the user code The partitions indicated by the installer will be ar

Download Pdf Manuals

image

Related Search

INT TSH int tsh 2 int tsh instrukcja

Related Contents

Instruction Manual  ME-183 NAV INTERFACE Description, Operation  Cent mille milliards de dessins - Inspection académique d`Ille  TELEVISOR A CORES MANUAL DE SERVIÇO  TdR Concurso Investigación UNICEF España  iStarUSA WN158  

Copyright © All rights reserved.
Failed to retrieve file