Home Theater PC Chassis
Contents
1. referenced picture Connect Card Reader USB cable See Motherboard User Manual for onboard USB port location and connection And see above referenced picture Connect LCD Cables Some of these steps follow after CPU amp Cooler installation 1 Use the orange tape in the accessory bag to tape the CPU heat sensor to the CPU heatsink so that LCD can display the CPU temperature accurately Connect the CPU heatsink fan to the LCD CPU Fan adapter if your motherboard has the auto fan speed control function base on CPU temp plug the extension cord to the motherboard fan connector In this case the LCD will only display fan speed no fan speed control will be available via the front knob Connect the PWR LCD power cord to the power A e supply like connecting the case fan This to eo i connection will provide power to r head placement is Power button LCD light recommended to ensure accurate CPU Temperature Reading gt gt LCD module Install Internal MCE Receiver User can convert the external MCE receiver dongle internally by installing the receiver PCB on the MCE Receiver IR Rack that comes with the case Right below the power button Unscrew the 2 thumb screws and take out the IR receiver rack Take out the MCE external receiver plastic enclosure by removing the two front rubber legs Carefully install the MCE receiver module to the rack check rack to ensure no metal touching to avoid circuit shortag2. such as Motherboard CPU RAM Memory Hard Drive DVD ROM Operating System etc Based on this assumption we make this user guide of quick installation guide Please follow the description step by step to assemble the components If you have any question in assembling the system you can contact your dealer or our technical support Safety Warning Turn down the CPU Cooler Fan Speed through the Front Controller may create vital damage to CPU Adjust Fan Controller CPU F R S appropriately according to the CPU instruction Minimum Fan Speed at 2000 is recommended CPU Fan Speed controller is default to minimum speed of 1800 to prevent CPU damage Overview Standard Components Equipped HTPC 180 Chassis NMEDIAPC MP 300 300W Micro ATX Power Supply 60mm Case Fan Air Duct Constant fresh air to CPU and avoid hot air re circulation All in 1 Card Reader 1 X USB onboard header required Front Connectors Onboard headers required o USB2 0 o IEEE 1394 o Audio Ports o RESET LCD Module Microsoft MCE receiver internal USB converter cable Microsoft MCE IR receive rack receiver not included Tight Cables amp Screws Installation Guides VVVVV V gt gt gt gt gt Other Components AMD Live Ready Hard Drive SATA is recommended RAM Memory Optical Drive DVD Burner is recommended Operating System Microsoft MCE 2005 or Vista with MCE is recommended Mouse amp Keyboard MCE 2005 or Vista with
3. Home Theater PC Chassis Model HTPC 180 BA amp SA Color Black amp Silver Quick Installation Guide U S amp Canada Only Version 1 0 DISCLAIMER No warranty or representation either expressed or implied is made with respect to the content of this documentation its quality performance merchantability or fitness for a particular purpose Information presented in this documentation has been carefully checked for reliability however no responsibility is assumed for inaccuracies The information contained in this documentation is subject to change without notice In no event will nMedia will be liable for direct indirect special incidental or consequential damages arising out of the use or inability to use this product or documentation even if advised of the possibility of such damages COPYRIGHT 2006 by NMEDIA SYSTEM INC All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form by any means without the written permission of NUEDIA SYSTEM INC TECHNICAL SUPPORT If a problem arises with your system and no solution can be obtained from this user guide please contact your place of purchase or local dealer REVISION HISTORY V 2 0 October 2006 Note This user guide is designed to provide the user a quick reference for chassis setup We assume you need the information regarding how to assemble the system
4. MCE remote wireless keyboard amp Receiver is recommended VVVV V For upgrades gt Sound Card gt Video Graphic Card Fanless model is recommended gt TV Tuner Card MCE certified is recommended Installation Flowchart Basic Procedures eeeee2eee0e7ee7e7eee7e7eeee e eee eee eeeeeeeeeeeeeeeeeeee e888 8 OO Oe Open Box gt Read Installation Guide gt Remove Top Cover gt Remove Optical Drive Bracket gt Take Off Power Supply gt Install Motherboard gt Perform Quality Check gt Connect Cables gt Install internal IR receivers if required gt Install Hard Drive gt Install CPU amp Cooler gt Install DIMM Memory Module gt Re Install Power Supply gt Install Optical Drive gt Connect Power Supply cables gt Replace top cover Installation Tools Screw Driver Screws Tight Cables Installation Guides T ip P Step 1 Make more room to work on 1 S After installing motherboard perform a quality check on chassis parts before continuing Connect the power button to board plug the PSU 20 or 24 pins and 4 pins cable temporarily connect the case fans power cord connect the LCD PWR cord Turn on the system At this point you should be assure that the case and PSU are functioning well by checking if the fans running good front LCD and VFD turning on Now unplug everything and follow the instruction to continue your build Due to the limited height of the compact case taking off the air duct m
5. ay be necessary if you use tall CPU heatsink like NMEDIAPC ICETANK cooler If you are using the ICETANK or ICECONE CPU cooler we recommend that you install the CPU and Cooler onto the motherboard before you slot it in the case This will smooth the cooler installation with more space outside of the case Some DVD trays cover need to be removed in order to eject the tray smoothly without blocking by the DVD flip down door When installing the DVD drive adjust the DVD drive appropriately until your case eject button can eject the tray smoothly then mark down the position and secure the DVD to the DVD rack with SCrews If you are planning to convert the MCE external receiver do it before motherboard installation otherwise you may need to un install everything in order to slot in the MCE receiver PCB board on the IR Rack Remember that installing power supply should always the last step when installing components Do not perform cable management until your system is fully configured This will make the cable management a better smooth procedure Do not install optional upgrade video card TV tuner card Sound card at once Use everything on board video amp sound to configure system and install operation system After then install the upgrades one by one and restart the system on every step to ensure component compatibility and save times of troubleshooting when issue arises Installation Open the top cover 2 Remove the DVD b
6. d and temperature above 60c 140 f environment Make sure the voltage of the power supply and adjust properly 110 230V Always unplug the power cord before inserting any add on devices Get the system checked by service personnel if below happens The power cable is damage Liquid has penetrated into the system Dropped and damaged RMA Return Policy All accessories and cables must be returned as they were shipped Carefully re packaging is needed to avoid shipping damages All warranties are subject to properly uses Any human power damages return may be rejected according to warranty terms and conditions Copyright 2006 NMEDIA SYSTEM INC All Right Reserve Q
7. e Secure the MCE receiver rack back to the case make sure the IR sensor head is facing accurately behind the plastic window Connect the receiver via the equipped USB converter cable to the onboard USB port Route the MCE IR Blaster sensor heads to the back of the case via the S PDIF PCI slot hole and stick them to the set top box s IR point Step 3 Install Hard Drive 1 There are three 3 5 bays available for this model 2 SATA hard amp wve is preferred to place under the optical drive since the cable is closer to the nbdard SATA ports most of the time JDE Ky es i l W Dooe a aea NN MW A E panus ae paar r Step 4 Install CPU and Cooler Follow your motherboard user manual to avoid damages Step 6 Install the power supply 1 Install the power supply 2 Connect power cables a to hard drive b to motherbaord 20 24 pin main c to motherborad 4 pin 12V d toLCD PWR e to optical drive Step 7 Install the optical drive LCD Module Set Up LCD will display the CPU amp Case Temp reading CPU Cooler Fan Speed reading Alarm Features CPU Alarm Temperature When CPU temperature hits 65 C or 149F the temperature reading will flash constantly until the temperature drops below the alarm degree CPU Fan Alarm When the fan stops running for whatever reason during working mode the CPU fan speed reading will flash constantly in 0000 until the fan is re spinning aga
8. in LCD shows CPU temperature and CPU heatsink fan speed when connecting appropriately The fan speed is automatically adjusted by the CPU temperature See below chart for more details CPU Temp gt 0 86 F 86 F amp up 104 F amp up 122 F amp up CPU Fan Spin 70 of full soeed 80 of full soeed 90 of full soeed 100 full speed Speed Warning By using LCD to display CPU Temperature and control CPU Heatsink fan speed periodically check heat sensor placement is required to ensure LCD displays CPU temperature accurately If you don t feel comfortable to have the LCD to control the heatsink fan speed just connect the fan to the motherboard fan pin connector instead Other Component Installation For other components including hard drive RAM CPU amp cooler optical drive and operating system etc plan the installation steps carefully and follow the user manual and motherboard manual instruction to avoid damages Reference picture only S PDIF Output Connection It is a standard PC S PDIF out jack Connect the header to the onboard S PDIF output port See below color codes o White Data or S PDIF out o Black Ground References Technical Support NMEDIA SYSTEM INC support nmediapc com http www nmediapc com support htm Safety Instructions Always read the step by step installation to protect your components Keep the user guide for future reference Keep away from humidity liqui
9. racket 3 Remove the Power Supply l y U j d E Step 2 Connect cables 1 Install motherboard 2 Connect front panel LCD cables Connect Front USB 2 0 IEEE 1394 and Audio Connectors Connect PWR Switch Connect Card Reader internal USB cable Connect LCD cables See below table for more details magga PA PTN ae trea ss A Reference picture only Front USB 2 0 IEEE 1394 and Audio Connectors See Motherboard User Manual for location and connection USB Port Color Codes IEEE 1394 Color Codes Audio Interface Red 5V Black Ground GND Pin 1 MIC IN Red White Data D Red 5V Pin 2 MIC GND Black Green Data D Blue TPB TPB Pin 5 amp 6 SR Black Ground GND White TPB TPB Pin 7 Empty White Yellow TPA TPA Green TPA TPA evoa LE O evoa D Pin 8 amp 9 SL O USB Diagram IEEE 1394 Diagram Front Audio AC 97 connection Tips First find the MIC and GND pin connect the MIC amp GND connector fist then the SR connector must on the Pin 5 amp 6 face the same label direction of the MIC amp GND connector plug the SR in same to the SL on Pin 8 amp 9 Plug the white NC single pin connector to Pin 7 Note There is no HD Audio connector from this model yet Connect the Power Button PWR amp RESET cable to the motherboard front panel jumper See Motherboard User Manual for location and connection And see above
Download Pdf Manuals
Related Search