HandyTone 386 Analog Telephone Adaptor User Manual
Contents
1. 0 9 0 9 A 22 B 222 C2222 D 33 E 333 F 3333 For example if the MAC address is 000b8200e395 it should be encoded as 0002228200333395 Step 3 To perform factory reset Press or the LED button for voice prompt Enter 99 and get the voice prompt Reset Enter the encoded MAC address of the device Wait for 15 seconds ao Of The device will reboot automatically and restore to factory default setting 36 HandyTone 386 User Manual Grandstream Networks Inc 9 Appendix I Glossary of Terms ADSL Asymmetric Digital Subscriber Line Modems attached to twisted pair copper wiring that transmit from 1 5 Mbps to 9 Mbps downstream to the subscriber and from 16 kbps to 800 kbps upstream depending on line distance AGC Automatic Gain Control is an electronic system found in many types of devices Its purpose is to control the gain of a system in order to maintain some measure of performance over a changing range of real world conditions ARP Address Resolution Protocol is a protocol used by the Internet Protocol IP RFC826 pecifically IPv4 to map IP network addresses to the hardware addresses used by a data link protocol The protocol operates below the network layer as a part of the interface between the OSI network and OSI link layer It is used when IPv4 is used over Ethernet ATA Analogue Telephone Adapter Covert analogue telephone to be used in data network for VoIP like Grandstream HT2. Select the ATA to report the log level Default is NONE The level is either one of DEBUG INFO WARNING or ERROR Syslog messages are sent based on the following events e product model version on boot up INFO level e NAT related info INFO level e sent or received SIP message DEBUG level e SIP message summary INFO level e inbound and outbound calls INFO level e registration status change INFO level e negotiated codec INFO level e Ethernet link up INFO level e SLIC chip exception WARNING and ERROR levels e memory exception ERROR level The Syslog uses USER facility In addition to standard Syslog payload it contains the following components GS LOG device MAC address error code error message Here is an example May 19 02 40 38 192 168 1 14 GS LOG 00 0b 82 00 a1 be 000 Ethernet link is up 24 HandyTone 386 User Manual Grandstream Networks Inc e FXS Port 1 Page SIP Server dc cali e g sip mycompany com or IP address Outbound Proxy e g proxy myprovider com or IP address if any SIP User ID EE the user part of an SIP address Authenticate ID can be identical to or different from SIP User ID Authenticate Password purposely not displayed for security protection Name dat optional e g John Doe Use DNS SRV E no E veg User ID is phone E E number No Yes SIP Registration E No E Yes Unregister On Reboot No L Yes Registe
3. Settings page Password field is purposely blanked for security reason after clicking update and saved The maximum password length 1s 25 characters Layer 3 QoS This field defines the layer 3 QoS parameter which can be the value used for IP Precedence or Diff Serv or MPLS Default value is 48 Layer 2 QoS Layer 2 QoS settings Default setting is blank Other VLAN supported equipments required if configured these settings No Key Entry Default is 4 seconds User can short or extend that depends on digits dialed timeout NAT Traversal This parameter defines whether the HT386 NAT traversal mechanism will be activated or not If activated by choosing Yes and a STUN server is also specified then the HT386 will behave according to the STUN client specification Under this mode the embedded STUN client inside the HT386 will attempt to detect if and what type of firewall NAT it is sitting behind through communication with the specified STUN server If the detected NAT is a Full Cone Restricted Cone or a Port Restricted Cone the HT386 will attempt to use its mapped public IP address and port in all of its SIP and SDP messages If the NAT Traversal field is set to Yes with no specified STUN server the HT386 will periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open STUN Server IP address or Domain name of the STUN server 22 HandyTone 386
4. 6 1 1 DHCP Mode Follow section 5 1 with voice menu option 01 to enable HandyTone 386 to use DHCP 6 1 2 STATIC IP Mode Follow section 5 1 with voice menu option 01 to enable HandyTone 386 to use STATIC IP mode then use option 02 03 04 to set up HandyTone 386 s IP Subnet Mask Gateway respectively 6 1 3 TFTP Server Address Follow section 5 1 with voice menu option 06 to configure the IP address of the TFTP server 6 2 Configuring HandyTone 386 with Web Browser HandyTone 386 ATA has an embedded Web server that will respond to HTTP GET POST requests It also has embedded HTML pages that allow users to configure the HandyTone 386 through a Web browser such as Microsoft s IE AOL s Netscape or Mozilla Firefox 6 2 1 Access the Web Configuration Menu First get the IP address of the HandyTone 386 through section 5 1 with menu option 02 Then access the HandyTone 386 s Web Configuration Menu using the following URI http Phone IP Address where the Phone IP Address is the IP address of the phone NOTE e To type IP address into browser to get the configuration page please strip out the announced leading 0 as the browser will parse in octet e g 1f the IP address reported 192 168 001 014 please type in 192 168 1 14 16 HandyTone 386 User Manual Grandstream Networks Inc 6 2 2 End User Configuration Once this HTTP request is entered and sent from a Web Browser the HandyTone 386 will respond with the fol
5. Current release is 1 0 3 21 Bootloader current version is 1 0 8 9 HTML cutrent version 1 0 3 21 VOC current version is 1 0 0 10 htm System Uptime This shows system up time since last reboot Registered Whether the unit is registered to service provider s server PPPoE Link Up This shows whether the PPPoE is up if connected to DSL modem NAT This shows what kind NAT the HT386 is connected to It is based on STUN protocol If the detected NAT is symmetric NAT STUN will not work and Outbound Proxy needed to make HT386 functioning correctly 18 HandyTone 386 User Manual Grandstream Networks Inc e Basic Settings Page ATTE End User purposely not displayed for security protection Password IP Address r E dynamically assigned via DHCP default or PPPoE will attempt PPPoE if DHCP fails and following is non blank PPPoE account ID PPPoE password PPPoE Service Name Preferred DNS server po fo fo po gt statically configured as IP Address 192 168 fo 160 Subnet Mask 255 2558 gt gt fo Default Router 192 168 fo fi DNS Server I 192 168 fo fi DNS Server 2 Time Zone GMT 5 00 US Eastern Time New York a Daylight Savings Ex No Time time PSTN access key pattern to use the PSTN line default is 00 code E Yes if set to Yes display time will be 1 hour ahead of normal End User This contains the password for end user to access the We
6. E No G Yes if set to Yes will function as the Re Dial key Es No do not send SUBSCRIBE for Message Waiting Indication E Yes send periodical SUBSCRIBE for Message Waiting Indication E No E Yes caller ID will be blocked if set to Yes Standard sr HandyTone 386 User Manual Grandstream Networks Inc e FXS Port 2 Page SIP Server SP ycompanye com e g sip mycompany com or IP address Outbound Proxy e g proxy myprovider com or IP address if any SIP User ID idi the user part of an SIP address Authenticate ID 4 can be identical to or different from SIP User ID Authenticate ooo Password purposely not displayed for security protection Name dat optional e g John Doe Use DNS SRV E no E veg User ID is phone E E number O Yes SIP Registration L No E Yes Unregister On Reboot No L Yes Register Expiration ee in minutes default 1 hour max 45 days local SIP port saa default 5062 local RTP port 8 1024 65535 default 5008 Use random port E No E Yes DTMF Payload Type 1 Send DTMF amp in audio via RTP RFC2833 via SIP INFO Send Flash Event Es No E Yes Flash will be sent as a DTMF event if set to Yes Enable Call Features E No E Yes if Yes Call Forwarding amp Call Waiting Disable are supported locally Offhook Auto Dial User ID extension to dial automatically when offhook Proxy Require Disabl
7. G 711 PCM a law and u law G 723 1 5 3K 6 3K G 726 32K as well as G 729A and iLBC Support Caller ID name display or block Call waiting caller ID Hold Call Waiting Flash Call Transfer Call Forward 3 way conferencing in band and out of band DTMF etc Support fax pass through for PCMU and PCMA and T 38 FoIP Fax over IP Support syslog Support Silence Suppression VAD Voice Activity Detection CNG Comfort Noise Generation Line Echo Cancellation G 168 and AGC Automatic Gain Control Support standard encryption and authentication DIGEST using MD5 and MD5 sess Support for Layer 2 802 1Q VLAN 802 1p and Layer 3 QoS ToS DiffServ MPLS Support automated NAT traversal without manual manipulation of firewall NAT Support device configuration via built in IVR Web browser or Central configuration files through TFTP or HTTP server Support firmware upgrade via TFTP or HTTP Support PSTN pass through Ultra compact wallet size and lightweight design great companion for travelers Compact lightweight Universal Power adapter HandyTone 386 User Manual Grandstream Networks Inc 4 2 Hardware Specification The table below lists the hardware specification of HandyTone 386 Model HandyTone 386 LAN interface IxRJ45 10Base T FXS telephone port 2 x FXS PSTN Port 1x PSTN pass through or life line port Button l LED Green and Red color Universal Switching Input 100 240V AC 50 60 Hz Power Adaptor Output 5VDC 120
8. User Manual Grandstream Networks Inc Keep alive interval Use NAT IP Firmware Upgrade and provisioning Via TFTP Server Via HTTP Server Automatic Upgrade Firmware Key FXS Impedance Default is 20 seconds The interval of sending dummy UDP packet to keep NAT pin hole open NAT IP address used in SIP SDP message Default is blank This radio button will enable HT 386 to download firmware or configuration file through either TFTP or HTTP This is the IP address of the configured TFTP server If selected and it is non zero or not blank the HT386 will attempt to retrieve new configuration file or new code image from the specified TFTP server at boot time It will make up to 3 attempts before timeout and then it will start the boot process using the existing code image in the Flash memory If a TFTP server is configured and a new code image is retrieved the new downloaded image will be verified and then saved into the Flash memory Note Please do NOT interrupt the TFTP upgrade process especially the power supply as this will damage the device Depending on the network environment this process can take up a few minutes The URL for the HTTP server used for firmware upgrade and configuration via HTTP For example http provisioning mycompany com 6688 Grandstream 1 0 5 16 Here 6688 is the specific TCP port that the HTTP server is listening at it can be omitted if using default port 80 Note If Auto U
9. and com is the top level domain FXO Foreign eXchange Office An FXO device can be an analog phone answering machine fax or anything that handles a call from the telephone company like AT amp T They should also operate the same way when connected to an FXS interface An FXO interface will accept calls from FXS or PSTN interfaces All countries and regions have their own standards 38 HandyTone 386 User Manual Grandstream Networks Inc FXO is complimentary to FXS and the PSTN FXS Foreign eXchange Station An FXS device has hardware to generate the ring signal to the FXO extension usually an analog phone An FXS device will allow any FXO device to operate as if it were connected to the phone company This makes your PBX the POTS PSTN for the phone The FXS Interface connects to FXO devices by an FXO interface of course DHCP The Dynamic Host Configuration Protocol DHCP is an Internet protocol for automating the configuration of computers that use TCP IP DHCP can be used to automatically assign IP addresses to deliver TCP IP stack configuration parameters such as the subnet mask and default router and to provide other configuration information such as the addresses for printer time and news servers ECHO CANCELLATION Echo Cancellation is used in telephony to describe the process of removing echo from a voice communication in order to improve voice quality on a telephone call In addition to improving quality this proc
10. target IP address to make a call Destination ports can be specified by 66 99 using 4 encoding for followed by the port number Examples 11 HandyTone 386 User Manual Grandstream Networks Inc If the target IP address is 192 168 0 10 the dialing convention is Voice Prompt with option 47 then 192 168 000 010 followed by pressing the FF key if it is configured as a send key or wait for more than 5 seconds If the target IP address port is 192 168 1 20 5062 then the dialing convention would be Voice Prompt with option 47 then 192168001020 45062 followed by pressing the key if it is configured as a send key or wait for 4 seconds NOTE e When doing direct IP call the Use Random Port should set to NO e You can NOT make direct IP calls between FXS1 to FXS2 since they are using same IP 5 2 3 Call Hold While in conversation pressing the flash button on the attached analogue phone if the phone has that button will put the remote end on hold Pressing the flash button again will release the previously held party and the bi directional media will resume If no flash button then on off hook quickly hook flash will do the same thing but also risk of losing call if the time is not short enough 5 2 4 Call Waiting If call waiting feature is enabled while the user is in a conversation he will hear a special stutter tone if there is another incoming call User can press t
11. the attached phone dial 1008 and then press the or wait for 4 seconds e To dial a PSTN number such as 6266667890 you might need to enter in some prefix number followed by the phone number Please check with your VoIP service provider to get the information If you phone is assigned with a PSTN like number such as 6265556789 most likely you just follow the rule to dial 16266667890 as if you were calling from a regular analog phone of North America then followed by pressing or wait for 4 seconds 5 2 2 Direct IP calls Direct IP calling allows two parties that is a HandyTone with an analog phone and another VoIP Device to talk to each other in an ad hoc fashion without a SIP proxy This kind of VoIP calls can be made between two parties if e Both HT386 and other VoIP Device i e another HandyTone ATA or Budgetone SIP phone or other VoIP unit have public IP addresses or e Both HT386 and other VoIP Device are on the same LAN using private IP addresses or e Both HT386 and other VoIP Device can be connected through a router using public or private IP addresses with necessary port forwarding or DMZ To make a direct IP call first pick up the analog phone or turn on the speakerphone on the analog phone then access the voice menu prompt by dial or press the button on the HandyTone 286 and dials 47 to access the direct IP call menu User will hear a voice prompt Direct IP Calling and a dial tone Enter a 12 digit
12. the specified registrar The default interval is 60 minutes or 1 hour The maximum interval is 65535 minutes about 45 days This parameter defines the local SIP port the HT386 will listen and transmit The default value is for FXS1 1s 5060 FXS2 is 5062 This parameter defines the local RTP RTCP port pair the HT 386 will listen and transmit It is the base RTP port for channel 0 When configured channel 0 will use this port value for RTP and the port_value 1 for its RTCP channel 1 will use port_value 2 for RTP and port_value 3 for its RTCP The default value for FXS1 is 5004 FXS2 is 5008 Default No If set to Yes the device will pick randomly generated SIP and RTP ports This is usually necessary when multiple SIP devices are behind the same NAT For Direct IP to IP call this should be set to No This parameter sets the payload type for DTMF using RFC2833 This parameter specifies the mechanism to transmit DTMF digit There are 3 modes supported in audio which means DTMF is combined in audio signal not very reliable with low bit rate codec via RTP RFC2833 or via SIP INFO Default is NO If set to yes flash will be sent as DTMF event 29 HandyTone 386 User Manual Grandstream Networks Inc Enable Call Features Offhook Auto Dial Proxy Require Disable Call Waiting Preferred Vocoder Voice Frames per TX G723 Rate iLBC frame size Default is Yes Advance call features and feature codes functions ar
13. total of 120 possible combinations A DECT base station an RFP Radio Fixed Part can transmit all 12 possible accesses time slots simultaneously by using different frequencies or using only one frequency All signaling information is transmitted from the RFP within a multiframe 16 frames Voice signals are digitally encoded into a 32 kbit s signal using Adaptive Differential Pulse Code Modulation DNS Short for Domain Name System or Service or Server an Internet service that translates domain names into IP addresses DID Direct Inward Dialing Direct Inward Dialing The ability for an outside caller to dial to a PBX extension without going through an attendant or auto attendant DSP Digital Signal Processing Using computers to process signals such as sound video and other analog signals which have been converted to digital form Digital Signal Processor A specialized CPU used for digital signal processing Grandstream products all have DSP chips built inside DTMF Dual Tone Multi Frequency The standard tone pairs used on telephone terminals for dialing using in band signaling The standards define 16 tone pairs 0 9 and A F although most terminals support only 12 of them 0 9 and FODN Fully Qualified Domain Name A FQDN consists of a host and domain name including top level domain For example www grandstream com is a fully qualified domain name www is the host grandstream is the second level domain
14. will only issue firmware upgrade request if there are changes in the firmware Prefix or Postfix 7 4 Managing Firmware and Configuration File Download When Automatic Upgrade is set to Yes Service Provider can use P193 Auto Check Interval in minutes default and minimum is 60 minutes to have the devices periodically check with either Firmware Server or Config Server whenever they are defined This allows the device periodically check if there are any new changes need to be taken on a scheduled time By defining different intervals in P193 for different devices Server Provider can spread the Firmware or Configuration File download in minutes to reduce the Firmware or Provisioning Server load at any given time 35 HandyTone 386 User Manual Grandstream Networks Inc 8 Restore Factory Default Setting Warning Restore the Factory Default Setting will DELETE all configuration information of the device Please backup or print out all the settings before you approach to following steps Grandstream will not take any responsibility if you lose all the parameters of setting and cannot connect to your service provider Please disconnect network cable and power cycle the unit before trying to reset the unit to factory default The steps are as follows Step 1 Find the MAC Address of the device It is a 12 digits HEX number located on the bottom of the unit Step 2 Encode the MAC address Please use the following mapping
15. 0mA UL certified Dimension 70mm W 130mm D 27mm H Weight 0 6lbs 0 3kg Temperature 40 130 F 5 45 C Humidity 10 90 non condensing Compliance FE CEC HandyTone 386 User Manual Grandstream Networks Inc 5 Basic Operations 5 1 Get Familiar with Voice Prompt Handy Tone 386 has stored a voice prompt menu for quick browsing and simple configuration Currently the voice prompt menu and the LED button is designed for FXS port 1 ONLY To enter this voice prompt menu simply press the button or from the analog phone Voice Prompt User s Options Main Menu Enter a Menu Option Enter for the next menu option Enter P to return to the main menu Enter 01 06 47 86 or 99 Menu option DHCP Mode Enter 9 to toggle the selection Static IP Mode If user selects Static IP Mode user need configure the all IP address information through menu 02 to 05 If user selects Dynamic IP Mode the device will retrieve all IP address information from DHCP server automatically when user reboots the device IP Address IP address The current WAN IP address is announced Enter 12 digit new IP address if in Static IP Mode Subnet IP address Gateway IP address DNS Server IP address 06 TFIPServer IP address Direct IP Calling When entered user will be prompted a dial tone dial a 12 digit IP address to make a direct IP call For details se
16. IP address format Here are examples of some valid URL e g firmware mycompany com 6688 Grandstream 1 0 8 16 e g 168 75 215 189 NOTES e TFTP server in IP address format can be configured via IVR Please refer to section 6 1 3 for instructions If TFTP server is in FQDN format it must be set via web configuration interface e Once a Firmware Server Path is set user needs to update the settings and reboot the device If the configured firmware server is found and a new code image 18 available the HandyTone ATA will attempt to retrieve the new image files by downloading them into the HandyTone ATA s SRAM During this stage the HandyTone ATA s LEDs will blink until the checking downloading process is completed Upon verification of checksum the new code image will then be saved into the Flash If TFTP HTTP fails for any reason e g TFTP HTTP server 1s not responding there are no code image files available for upgrade or checksum test fails etc the HandyTone ATA will stop the TFTP HTTP process and simply boot using the existing code image in the flash e Firmware upgrade may take as long as 1 to 20 minutes over Internet or just 20 seconds if it is performed on a LAN It is recommended to conduct firmware upgrade in a controlled LAN environment if possible For users who do not have a local firmware upgrade server Grandstream provides a NAT friendly TFTP server on the public Internet for firmware upgrade Please check the Serv
17. User Manual Handy Tone 386 Analog Telephone Adaptor For Firmware Release Version 1 0 3 18 Grandstream Networks Inc www grandstream com G GRANDSTREAM NETWORKS e Z nstteam Innovative 1 Aansiream HandyTone 386 User Manual Grandstream Networks Inc Table of Contents E VERGE 4 INSTANS 5 3 WHAT IS INCLUDED IN THE PACKAGE siii ts 7 L SAFETY COMPLIANCE NN 7 VENN 7 A PRODUCT OV ERY TW ee 8 Al REY REATURES NN 8 22 HRD RES ETT TIN Ne 9 gt BASIC OPERATIONS ss 10 5 1 GET FAMILIAR WITH VOICE PROMPT erovnevnnvnnvnnvnnvnnennennennennennennennennennennennennennennennene 10 ST MR PHONE MNA 11 5 2 1 Calling phone or extension numbers rrrrnrrnnnnnnrrnrnnnnnnnrnnvnnnnnnrrnnrnnnnenrrnrrnnnnennene Il 322 Direct Nene 1 I 018210 0 PE SEE EE EE O O OR EA 12 EE NNN 12 De GE O too 12 SO AWAN OT ANNAN 13 SLT PINS LURO a N E a 13 o CENTRES NS 14 XIA Call Features Table Siar COLO iii hisba redan 14 Daoud PSTN POSS Ton Leker 15 FASTPRIS 15 5 5 LED LIGHT PATTERN INDICATION 2 00008 ERROR BOOKMARK NOT DEFINED 6 CONFIGURATION GUIDE assosiere 16 6 1 CONFIGURING HANDYTONE 386 LAN IP THROUGH VOICE PROMPT 02ceeceeees 16 OLI IP 16 6I SUATIC P MOE ee dio 16 6 1 3 TFTP Server ACdreSS cccccccccccccuccuccccccuccecccusceccscesceccecuecescscaecussscuscscesuscuscesaes 16 6 2 CONFIGURING HANDY TONE 386 WITH WEB BROWSER esrevnnvnnvnnvnnvnnvnnvnnennennennennene 16 6 2 1 Access the
18. Video Transport Working Group of the IETF and first published in 1996 as RFC 1889 Session Description Protocol is a format for describing streaming media initialization parameters It has been published by the IETF as RFC 2327 Session Initiation Protocol An IP telephony signaling protocol developed by the IETF RFC3261 SIP is a text based protocol suitable for integrated voice data applications SIP is designed for voice transmission and uses fewer resources and is considerably less complex than H 323 All Grandstream products are SIP based Simple Traversal of UDP over NATS is a network protocol allowing clients behind NAT or multiple NATs to find out its public address the type of NAT it is behind and the internet side port associated by the NAT with a particular local port This information is used to set up UDP communication between two hosts that are both behind NAT routers The protocol is defined in RFC 3489 STUN will usually work good with non symmetric NAT routers Transmission Control Protocol is one of the core protocols of the Internet protocol suite Using TCP applications on networked hosts can create connections to one another over which they can exchange data or packets The protocol guarantees reliable and in order delivery of sender to receiver data Trivial File Transfer Protocol is a very simple file transfer protocol with the functionality of a very basic form of FTP It uses UDP port 69 as its transport proto
19. Web Configuration Menu rrrnnnnnnnnnnnnnnnnnnnnnnnnnnnrvnnnrnnnnnnnnnnrrrnnnnnnnnn 16 O22 ENTUS GEER EE nlobiee aaeaniadeinabebeos 17 6 2 3 Advanced Configuration and FXS ports Parameters rrrrrrrnnrrnnnnnnnnnnrrnnnnrnnnnn 21 6 2 4 Saving the Configuration Changes rrrnnnnnnnnnnnnnnnrrnnnnnnnvvvrrnnnnnnnnnnnnnnnnnnrrrrnrenennnn 32 6 2 5 Rebooting the HandyTone 386 from Remote rrnnnrrrnnnrrnnnnnnnnnrnnnrnnnnnnnnnnrrnnnnrnnnnn 32 6 3 CONFIGURATION THROUGH A CENTRAL SERVER cccccccscscceccsccecceccecescescescesceecesces 33 T SOFTWARE UPGRADE 0000 rt o aes ae eee ee ees 34 7 1 FIRMWARE UPGRADE THROUGH TFTP HTTP 0 coco ce eee eecesccececcescescescescescesces 34 72 CONFIGURATION FILE DOWNLOAD NN 35 HandyTone 386 User Manual Grandstream Networks Inc 7 3 FIRMWARE AND CONFIGURATION FILE PREFIX AND POSTFIX EE die det tian A 35 7 4 MANAGING FIRMWARE AND CONFIGURATION FILE DOWNLOAD 0ccecececescececes 35 8 RESTORE FACTORY DEFAULT SETTING 0 0 0000 0 00000000000 4 36 9 APPENDIX I GLOSSARY OF TERMS 0 cc cc cece eee rrn 37 HandyTone 386 User Manual Grandstream Networks Inc 1 Welcome Congratulations on becoming an owner of HandyTone 386 You made an excellent choice and we hope you enjoy all of its capabilities Grandstream s HandyTone 386 is an all in one VoIP integrated access device that features superb audio quality rich functionalities high level of in
20. and get the dial tone then hang up Flash Hook When in conversation this action will switch to the new incoming call if user heard the call waiting sound When in conversation and no incoming call heard this action will switch to a new channel for a new call 90 Busy Call Forward To use this feature dial 90 wait for the dial tone Then dial 8 9 9 9 9 14 HandyTone 386 User Manual Grandstream Networks Inc 5 3 2 PSTN Pass Through Life Line When HandyTone 386 is out of power the RJ 11 line jack on the HandyTone 386 side will function as a pass through jack The user will be able to use the analog phone for PSTN calls directly without press the access code 5 4 FAX Support Handy Tone 386 supports FAX in two modes T 38 Fax over IP and fax pass through T 38 is the preferred method because it is more reliable and works well in most network conditions If the service provider supports T 38 please use this method by selecting Fax mode to be T 38 default If the service provider does not support T 38 pass through mode may be used To send or receive faxes in fax pass through mode users must select all the Preferred Codecs to be PCMU PCMA G 7 I 1 u a 5 5 LED Light Pattern Indication Following are the LED light pattern indications Device Malfunctions 15 HandyTone 386 User Manual Grandstream Networks Inc 6 Configuration Guide 6 1 Configuring HandyTone 386 LAN IP through Voice Prompt
21. b Configuration Password Menu User can put new password here This field is case sensitive with maximum of 25 characters HandyTone 386 User Manual Grandstream Networks Inc IP Address Time Zone Daylight Savings Time PSTN Access Code If DHCP mode 1s enabled then all the field values for the Static IP mode are not used even though they are still saved in the Flash memory The HT386 will acquire its IP address from DHCP in the network PPPoE settings is usually for DSL ADSL modem users The HandyTone will attempt to establish a PPPoE session if PPPoE account is set If Static IP mode 1s selected the IP address Subnet Mask Default Router IP address DNS Server mandatory DNS Server 2 optional fields need to be configured Displayed date time will be adjusted according to the specified time zone Default NO If set to Yes then the displayed time will be I hour ahead of normal time Default is 00 user can change it By pressing the code user can switch the phone to PSTN line connected to the Line port of ATA and make PSTN outgoing calls This is called PSTN Pass Through 20 HandyTone 386 User Manual Grandstream Networks Inc 6 2 3 Advanced Configuration and FXS ports Parameters To login to the Advanced Setting and FXS port configuration pages administrator password Is required The default administrator password is admin User can change the administrator password here The password is case
22. can be same or different from the Firmware Server Path A configuration parameter is associated with each particular field in the web configuration page A parameter consists of a Capital letter P and 2 to 3 Could be extended to 4 in the future digit numeric numbers 1 e P2 is associated with Admin Password in the ADVANCED SETTINGS page For a detailed parameter list please refer to the corresponding firmware release configuration template When Grandstream Device boots up or reboots it will issue request for configuration file named C SXXXXXXXXXXXX Where XXXXXXXXxxxx is the MAC address of the device 1 e cfg000b820102ab The configuration file name should be in lower cases 7 3 Firmware and Configuration File Prefix and Postfix Starting from firmware version 1 0 7 11 for HandyTone 486 Rev 2 0 adding prefix and postfix for both firmware and configuration file 1s supported Firmware Prefix and Postfix allows device to download the firmware name with the matching Prefix and Postfix This makes it the possible to store ALL of the firmware with different version in one single directory Similarly Config File Prefix and Postfix allows device to download the configuration file with the matching Prefix and Postfix Thus multiple configuration files for the same device can be stored in one directory In addition when the field Check New Firmware only when F W pre suffix changes is set to Yes the device
23. col 41 HandyTone 386 User Manual Grandstream Networks Inc UDP User Datagram Protocol UDP is one of the core protocols of the Internet protocol suite Using UDP programs on networked computers can send short messages known as datagrams to one another UDP does not provide the reliability and ordering guarantees that TCP does datagrams may arrive out of order or go missing without notice However as a result UDP is faster and more efficient for many lightweight or time sensitive purposes VAD Voice Activity Detection or Voice Activity Detector is an algorithm used in speech processing wherein the presence or absence of human speech is detected from the audio samples VLAN A virtual LAN known as a VLAN is a logically independent network Several VLANs can co exist on a single physical switch It is usually refer to the IEEE 802 1Q tagging protocol VoIP Voice over IP VoIP encompasses many protocols All the protocols do some form of signalling of call capabilities and transport of voice data from one point to another e g SIP H 323 etc 42
24. e 4 2 2 Make a Direct IP Call RESET Enter 9 to reboot the device or Enter MAC address to restore factory default setting For details see section 8 Invalid Entry Automatically return to Main Menu e Once the button is pressed it enters the voice prompt main menu If the button is pressed again while it is already in the voice prompt menu it jumps to Direct IP Call option and a dial tone is prompted e shifts down to the next menu option e returns to the main menu 9 functions as the ENTER key in many cases to confirm an option 10 HandyTone 386 User Manual Grandstream Networks Inc e All entered digit sequences have known lengths 2 digits for menu option and 12 digits for IP address For IP address add 0 before the digits if the digits are less than 3 like 192 168 0 26 should be key in like 192168000026 no dot needed while input Once all of the digits are collected the input will be processed e Key entry can not be deleted but the phone may prompt error once it is detected 5 2 Make Phone Calls 5 2 1 Calling phone or extension numbers There are currently two methods to make an extension number call a Dial the numbers directly and wait for 4 default seconds b Dial the numbers directly and press assuming that use as dial key is selected in web configuration Examples e To dial another extension on the same proxy such as 1008 simply pick up
25. e remote reboot etc Grandstream provide GAPS Grandstream Automated Provisioning System service to VoIP service providers It could be either simple redirection or with certain special provisioning settings Initially upon booting up Grandstream devices by default point to Grandstream provisioning server GAPS based on the unique MAC address of each device GAPS provision the devices with redirection settings so that they will be redirected to customer s TFTP server for further provisioning Grandstream also provide GAPSLite software package which contains our NAT friendly TFTP server and a configuration tool to facilitate the task of generating device configuration files The GAPSLite configuration tool is now free to end users The tool and configuration template can be downloaded from http www grandstream com DOWNLOAD Configuration Tool For details on how GAPS works please refer to the documentation of GAPS product 33 HandyTone 386 User Manual Grandstream Networks Inc 7 Software Upgrade Software upgrade can be done via either TFTP or HTTP The corresponding configuration settings are in the ADVANCED SETTINGS configuration page 7 1 Firmware Upgrade through TFTP HTTP To upgrade via TFTP or HTTP the Firmware Upgrade and Provisioning upgrade via field needs to be set to TFTP or HTTP respectively Firmware Server Path needs to be set to a valid URL of a TFTP or HTTP server server name can be in either FQDN or
26. e Call Waiting E No Yes 21 HandyTone 386 User Manual Preferred Vocoder in listed order Voice Frames per TX G723 rate IiLBC frame size iLBC payload type Silence Suppression Fax Mode Early Dial Dial Plan Prefix Use as Dial Key SUBSCRIBE for MWI Send Anonymous Special Feature EET current setting is PCMU choice 2 hes choice 3 67298 x choice 4 pez B choice 5 er choice 6 el up to 10 20 32 64 for G711 G726 G723 other codecs respectively ka 6 3kbps encoding rate 5 3kbps encoding rate a 20ms La 30ms 7 between 96 and 127 defanlt is 97 E No E Yes E T 38 Auto Detect E Pass Through No E Yes use Yes only if proxy supports 484 response this prefix string 1s added to each dialed number E No G Yes af set to Yes will function as the Re Dial key E No do not send SUBSCRIBE for Message Waiting Indication E Yes send periodical SUBSCRIBE for Message Waiting Indication E No E Yes caller ID will be blocked if set to Yes Standard The explanations provided apply to both of the FXS port configuration parameters SIP Server IP address or Domain name provided by VoIP service provider IP address or Domain name of Outbound Proxy or Media Gateway or Session Outbound Proxy Border Controller Used by ATA for firewall or NAT penetration in different network envir
27. e supported locally This parameter allows a user to configure a User ID or extension number to be automatically dialed upon offhook Please note that only the user part of a SIP address needs to be entered here The HT386 will automatically append the 0 and the host portion of the corresponding SIP address NOTE Please write down the IP address of the ATA if you use this feature as it will disable the IVR and the only way to access the HT386 is via web configuration page SIP Extension to notify SIP server that the unit is behind the NAT Firewall Default is No User can use code to use this feature per call basis The HT386 supports 6 different codec types including G 711 A U law G 723 1 G 726 G 729A B iLBC A user can configure codecs in a preference list that will be included with the same preference order in SDP message This field contains the number of voice frames to be transmitted in a single packet When setting this value the user should be aware of the requested packet time used in SDP message as a result of configuring this parameter This parameter is associated with the first codec in the above codec Preference List or the actual used payload type negotiated between the 2 conversation parties at run time e g if the first codec 1s configured as G723 and the Voice Frames per TX is set to be 2 then the ptime value in the SDP message of an INVITE request will be 60ms because each G723 voice frame c
28. ernet Telephony are often used to mean the same however they are not 100 per cent interchangeable since Internet is only a subcase of packet switched networks For users who have free or fixed price Internet access IP Telephony software essentially provides free telephone calls anywhere in the world However the challenge of IP Telephony is maintaining the quality of service expected by subscribers Session border controllers resolve this issue by providing quality assurance comparable to legacy telephone systems IVR is a software application that accepts a combination of voice telephone input and touch tone keypad selection and provides appropriate responses in the form of voice fax callback e mail and perhaps other media A Maximum Transmission Unit MTU is the largest size packet or frame specified in octets eight bit bytes that can be sent in a packet or frame based network such as the Internet The maximum for Ethernet is 1500 byte Network Address Translation Network Time Protocol a protocol to exchange and synchronize time over networks The port used is UDP 123 Grandstream products using NTP to get time from Internet OBP SBC Outbound Proxy or another name Session Border Controller A device used in VoIP networks OBP SBCs are put into the signaling and media path between calling and called party The OBP SBC acts as if it was the called VoIP phone and places a second call to the called party The effect of this behavio
29. ess improves bandwidth savings achieved through silence suppression by preventing echo from traveling across a network There are two types of echo of relevance in telephony acoustic echo and hybrid echo Speech compression techniques and digital processing delay often contribute to echo generation in telephone networks H 323 A suite of standards for multimedia conferences on traditional packet switched networks HTTP Hyper Text Transfer Protocol the World Wide Web protocol that performs the request and retrieve functions of a server IP Internet Protocol A packet based protocol for delivering data across networks IP PBX IP based Private Branch Exchange IP Telephony Internet Protocol telephony also known as Voice over IP Telephony A general term for the technologies that use the Internet Protocol s packet switched connections to exchange voice fax and other forms of information that have traditionally been carried over the dedicated 39 HandyTone 386 User Manual Grandstream Networks Inc IVR MTU NAT NTP circuit switched connections of the public switched telephone network PSTN The basic steps involved in originating an IP Telephony call are conversion of the analog voice signal to digital format and compression translation of the signal into Internet protocol IP packets for transmission over the Internet or other packet switched networks the process is reversed at the receiving end The terms IP Telephony and Int
30. he above message 6 2 5 Rebooting the HandyTone 386 from Remote The administrator of the HandyTone 386 can remotely reboot the HT386 by clicking on the Reboot button at the bottom of the configuration page Once done the following screen will be displayed to indicate that rebooting is underway The device is rebooting now You may relogin by clicking on the link below in 30 seconds Click to relogin At this point the user can relogin to the HandyTone 386 after waiting for about 30 seconds 6 3 Configuration through a Central Server Grandstream HT386 can be automatically configured from a central provisioning system 32 HandyTone 386 User Manual Grandstream Networks Inc When HT386 boots up it will send TFTP request to download configuration files there are two configuration files one is cfg txt and the other is c fg000b82xxxxxx where O00b82xxxxxx is the MAC address of the HT386 The configuration files can be downloaded via TFTP from the central server A service provider or an enterprise with large deployment of HT386 can easily manage the configuration and service provisioning of individual devices remotely from a central server Grandstream provides a licensed provisioning system called GAPS that can be used to support automated configuration of HT386 GAPS Grandstream Automated Provisioning System uses enhanced NAT friendly TFTP to communicate with each individual HT386 for firmware upgrad
31. he flash button to put the current call party on hold and switch to the other call Pressing flash button toggles between two active calls 5 2 5 Call Transfer 5 2 5 1 Blind Transfer Assume that call party A and B are in conversation A wants to Blind Transfer B to C 1 A press FLASH on the analog phone to hear the dial tone 2 Then A dials 87 then dials C s number and then or wait for 4 seconds 3 A can hang up NOTE e Enable Call Feature has to be set to Yes in web configuration page A can hold on to the phone and await one of the three following behaviors e A quick confirmation tone temporarily using the call waiting indication tone followed by a dial tone This indicates the transfer is successful transferee has received a 200 OK from transfer target At this point can either hang up or make another call 12 HandyTone 386 User Manual Grandstream Networks Inc e A quick busy tone followed by a restored call on supported platforms only This means the transferee has received a 4xx response for the INVITE and we will try to recover the call The busy tone is just to indicate to the transferor that the transfer has failed e Busy tone keeps playing This means we have failed to receive the second NOTIFY from the transferee and decided to time out Note this does not indicate the transfer has been successful nor does it indicate the transfer has failed When transferee 1s a client that does not sup
32. ices section of Grandstream s Web site to obtain our public TFTP server s IP address e Alternatively user can download a free TFTP or HTTP server and conduct local firmware upgrade A free windows version TFTP server is available for download from http support solarwinds net updates New customerFree cfm Our latest official release can be downloaded from http www grandstream com y firmware htm Unzip the file and put all of them under the root directory of the TFTP server Put the PC running the TFTP server and the HandyTone ATA in the same LAN segment Please go to File gt Configure gt Security to change the TFTP server s default setting from Receive Only to Transmit Only for the firmware upgrade Start the TFTP server in the HandyTone ATA s web configuration page configure the Firmware Server Path with the IP address of the PC update the change and reboot the unit Please be advised that our client will pull out firmware from the WAN side if the TFTP server is connected to the device s LAN port the firmware upgrade will not work by design 34 HandyTone 386 User Manual Grandstream Networks Inc 7 2 Configuration File Download Grandstream SIP Device can be configured via Web Interface as well as via Configuration File through TFTP or HTTP Config Server Path is the TFTP or HTTP server path for configuration file It needs to be set to a valid URL either in FQDN or IP address format The Config Server Path
33. in Phone port Phone 2 port or FXS port 2 does NOT have this feature e To receive PSTN calls simply make phone off hook when the analog phone rings 13 HandyTone 386 User Manual e To make a PSTN call simply press the PSTN access code 00 Grandstream Networks Inc is default or any number configured in web configuration page to switch to the PSTN line and get dial tone then dial the number 5 3 Call Features 5 3 1 Call Features Table Star Code Following table shows the call features code of Handy Tone 386 Call Features 23 3 way Conferencing Refer 5 2 6 above for procedure to perform 3 way Calling Enable Call Waiting Per Call 72 Unconditional Call Forward 7 Cancel Unconditional Call Forward dial tone then hang up To use this feature dial 72 wait for the dial tone Then dial the forward number ended with wait for dial tone hang up To cancel Unconditional Call Forward dial 73 and get the Blind Transfer Refer 5 2 5 1 above for procedure to perform Blind Transfer the forward number ended with wait for dial tone hang up Cancel Busy Call Forward To cancel Busy Call Forward dial 91 and get the dial tone then hang up 2 Delayed Call Forward To use this feature dial 92 wait for the dial tone Then dial the forward number ended with wait for dial tone hang up Q3 Cancel Delayed Call Forward To cancel this Forward dial 93
34. lowing login screen Password Login The password is case sensitive with maximum length of 25 characters The factory default password for End User and administrator is 123 and admin respectively Only administrator can get access to the ADVANCED SETTING configuration page NOTE e Ifyou CAN NOT log into the configuration page by using default password please check with the VoIP service provider Most likely the VoIP service provider has provisioned the device and configured for you therefore the password has already been changed 17 HandyTone 386 User Manual Grandstream Networks Inc After a correct password is entered in the login screen the embedded Web server inside the HandyTone 386 will respond with the Configuration pages which are explained in details below e Status Page MAC Address 00 0B 82 00 00 00 IP Address 192 168 1 109 Product Model HT386 Software Version Program 1 0 3 18 Bootloader 1 0 8 9 HTML 1 0 3 18 VOC 1 0 0 10 System Up Time 0 day s 0 hour s 2 minute s Registered Yes PPPoE Link Up disabled NAT detected NAT type is full cone MAC Address The device ID in HEX format This is very important ID for ISP troubleshooting IP Address This field shows IP address of the HT386 Product Model This field contains the product model info such as HT386 Software Version Program This is the main software release This number is always used for firmware upgrade
35. mer End users should contact the company from whom you purchased the product for replacement repair or refund If you purchased the product directly from Grandstream contact your Grandstream Sales and Service Representative for a RMA Return Materials Authorization number Grandstream reserves the right to remedy warranty policy without prior notification Warning Please do not attempt to use a different power adaptor Using other power adaptor may damage the HandyTone 386 and will void the manufacturer warranty Caution Changes or modifications to this product not expressly approved by Grandstream or operation of this product in any way other than as detailed by this User Manual could void your manufacturer warranty Information in this document is subject to change without notice No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of Grandstream Networks Inc HandyTone 386 User Manual Grandstream Networks Inc 4 1 4 Product Overview Key Features Supports SIP 2 0 RFC 3261 TCP UDP IP RTP RTCP HTTP ICMP ARP RARP DNS DHCP both client and server NTP PPPoE STUN TFTP etc Supports dual SIP accounts via dual FXS ports Powerful digital signal processing DSP to ensure superb audio quality advanced adaptive jitter control and packet loss concealment technology Support various codecs including
36. one 386 is a LINE port or PSTN pass through port Each FXS port can have a separate SIP account This is a key feature of HandyTone 386 Both ports can make calls concurrently HandyTone 386 User Manual Grandstream Networks Inc Following are the steps to install a HandyTone 386 l 3 4 J Connect a standard touch tone analog telephone or fax machine to FXS port 1 Connect another standard touch tone analog telephone or fax machine to FXS port 2 Insert a standard telephone cable into the LINE port of HandyTone 386 and connect the other end of the telephone cable to a wall jack Insert the Ethernet cable into the LAN port of HandyTone 386 and connect the other end of the Ethernet cable to an uplink port a router or a modem etc Insert the power adapter into the HandyTone 386 and connect it to a wall outlet Please follow the instructions in section 6 2 1 to configure the HandyTone 386 HandyTone 386 User Manual Grandstream Networks Inc 3 What is Included in the Package The Handy Tone 386 package contains 1 One HandyTone 386 2 One universal power adaptor 3 One Ethernet cable 3 1 Safety Compliances The Handy Tone 386 is compliant with various safety standards including FCC CE and C tick Its power adaptor is compliant with UL standard The Handy Tone 386 should only operate with the universal power adaptor provided in the package 3 2 Warranty Grandstream has a reseller agreement with our reseller custo
37. onment If symmetric NAT is detected STUN will not work and ONLY Outbound Proxy will work 28 Grandstream Networks Inc HandyTone 386 User Manual Grandstream Networks Inc SIP User ID Authenticate ID Authentication Password Name Use DNS SRV User ID is Phone Number SIP Registration Unregister On Reboot Register Expiration Local SIP port Local RTP port Use Random Port DTMF Payload Type Send DIMF Send Flash Event User account information provided by VoIP service provider ITSP usually has the form of digit similar to phone number or actually a phone number ID used for authentication usually same as SIP user ID but could be different and decided by ITSP Password for ATA to register to SIP servers of ITSP Purposely blank out once saved for security Maximum length is 25 User name not user ID for information only Default is No If set to Yes the client will use DNS SRV to lookup for the server If the HandyTone If set to yes a user phone parameter will be attached to the From header in SIP request This parameter controls whether the HT386 needs to send REGISTER messages to the proxy server The default setting is Yes Default is No If set to Yes the device will first send registration request to indicate SIP registra to remove previous bindings This parameter allows the user to specify the time frequency in minutes the HT386 will refresh its registration with
38. ontains 30ms of audio Similarly if this field is set to be 2 and if the first codec chosen is G729 or G711 or G726 then the ptime value in the SDP message of an INVITE request will be 20ms If the configured voice frames per TX exceeds the maximum allowed value the HT386 will use and save the maximum allowed value for the corresponding first codec choice The maximum value for PCM is 10 x10ms frames for G726 it is 20 xlOms frames for G723 it is 32 x30ms frames for G729 G728 64 x10ms and 64 x2 5ms frames respectively Please be careful when massage those parameters Encoding rate for G723 codec By default 6 3kbps rate is set iLBC packet frame size Default is 20ms For Asterisk PBX 30ms might need to be set 30 HandyTone 386 User Manual Grandstream Networks Inc iLBC payload type Silence Suppression Fax Mode Early Dial Dial Plan Prefix Use as Dial Send Key Subscribe for MWI Send Anonymous Lock keypad update Special Feature Payload type for iLBC Default value is 97 The valid range 1s between 96 and TE This controls the silence suppression V AD feature of G723 and G729 If set to Yes when a silence is detected small quantity of VAD packets instead of audio packets will be sent during the period of no talking If set to No this feature is disabled T 38 Auto Detect FoIP by default or Pass Through must use codec PCMU PCMA Default is No Use only if proxy
39. pgrade is set to No HT386 will only do HTTP download once at boot up Choose Yes to enable automatic upgrade and provisioning In Check for new firmware every field enter the number of days to enable HT386 to check the server for firmware upgrade or configuration in the defined period of days When set to No HT 386 will only do upgrade once at boot up Always check for New Firmware Check New Firmware only when F W pre suffix changes 32 digit in Hexadecimal Once configured the firmware will ONLY be changed if the key is matched This will lock the unit and firmware by ITSP Useful for IT SP to encrypt firmware End user should keep it blank Selects the impedance of the analog telephone connected to the Phone port 23 HandyTone 386 User Manual Grandstream Networks Inc Caller ID Scheme Onhook Voltage Polarity Reversal NTP server Syslog Server Syslog Level e Bellcore North America e CID Canada e DTMF Brazil e DTMF Denmark e FTSI DTMF Finland Sweden e ETSI FSK France Germany Norway Taiwan UK CCA Select the onhook voltage to suit different area or PBX Default is No If set to Yes polarity will be reversed upon call establishment and termination URI or IP address of the NTP Network Time Protocol server which the HT386 will use to synchronize the date time The IP address or URL of syslog server especially useful for ITSP Internet Telephone Service Provider
40. port the second NOTIFY such as our own earlier firmware this will be the case In bad network scenarios this could also happen although the transfer may have been completed successfully 5 2 5 2 Attended Transfer Assume that call party A and B are in conversation A wants to Attend Transfer B to C 1 A presses FLASH on the analog phone to get a dial tone 2 A then dial C s number followed by or wait for 4 seconds 3 IfC answers the call A and C are in conversation Then A can hang up to complete transfer 4 If C does not answer the call A can press flash back to talk to B NOTE e When Attended Transfer failed and A hang up the HandyTone 386 will ring user A back again to remind A that B is still on the call A can pick up the phone to restore conversation with B 5 2 6 3 way Conferencing Assume that call party A and B are in conversation A wants to bring C in a conference 1 A presses FLASH or Hook Flash for old model phones to get a dial tone 2 A dials 23 then C s number then or wait for 4 seconds 3 IfC answers the call then A press flash to bring B C in the conference 4 If C does not answer the call A can press flash back to talk to B NOTE e Ifthe conference organizer this case A drop the call all three party will be dropped 5 2 7 PSTN Pass Through HandyTone 386 supports PSTN pass through on FXS port User can make and receive PSTN calls with attached analog phone
41. r Expiration ee in minutes default 1 hour max 45 days local SIP port 5 default 5060 local RTP port 5004 1024 65535 default 5004 Use random port EE No E Wee DTMF Payload Type 1 Send DTMF amp in audio via RTP RFC2833 via SIP INFO Send Flash Event Es No E Yes Flash will be sent as a DTMF event if set to Yes Enable Call Features E No E Yes if Yes Call Forwarding amp Call Waiting Disable are supported locally Offhook Auto Dial User ID extension to dial automatically when offhook Proxy Require Disable Call Waiting E No Yes 25 HandyTone 386 User Manual Preferred Vocoder in listed order Voice Frames per TX G723 rate IiLBC frame size LBC payload type Silence Suppression Fax Mode Early Dial Dial Plan Prefix Use as Dial Key SUBSCRIBE for MWI Send Anonymous Special Feature Grandstream Networks Inc current setting is PCMU choice 1 current setting is PCMA choice 2 current setting is G729 choice 3 G 723 1 choice 4 G 726 32 choice 5 bd iLBC choice 6 gt e to 10 20 32 64 for G711 G726 G723 other codecs respectively Es 6 3kbps encoding rate E 5 3kbps encoding rate E 20ms s 30ms 96 and 127 default is 97 e No s Yes G T 38 Auto Detect E Pass Through e No E Yes use Yes only if proxy supports 484 response ais prefix string is added to each dialed number
42. sensitive and the maximum length is 25 characters e Advanced Settings Page purposely not displayed for security protection Admin Password Layer 3 QoS ii Diff Serv or Precedence value Layer 2 QoS 802 1Q VLAN Tag 802 1p priority EK 0 7 No Key Entry Timeout in seconds default is 4 seconds STUN server is stun sipserver com URI or IP port keep alive interval a in seconds default 20 seconds Use NAT IP used in SIP SDP message if specified Firmware Upgrade and ade and Upgrade Via Po TFTP E HTTP Provisioning fm grandstream com gs Firmware Server Path fm grandstream conVgs Config Server Path Firmware File Prefix Firmware File Postfix Config File Prefix Config File Postfix Automatic Upgrade G No E Yes check for upgrade every OG minutes default 7 days E Always Check for New Firmware E Check New Firmware only when F W pre suffix changes 21 HandyTone 386 User Manual Grandstream Networks Inc Firmware Key in Hexadecimal Representation FXS Impedance 600 Ohm North America Caller ID Scheme Bellcore North America Onhook Voltage 36v Polarity Reversal ka No La Yes reverse polarity upon call establishment and termination NTP Server tmnstgr URI or IP address Syslog Server nm Syslog Level NENE Admin Password Administrator password Only administrator can configure the Advanced
43. series products CODEC Abbreviation for Coder Decoder It s an analog to digital A D and digital to analog D A converter for translating the signals from the outside world to digital and back again CNG Comfort Noise Generator geneate artificial background noise used in radio and wireless communications to fill the silent time in a transmission resulting from voice activity detection DATAGRAM A data packet carrying its own address information so it can be independently routed from its source to the destination computer DECIMATE To discard portions of a signal in order to reduce the amount of information to be encoded or compressed Lossy compression algorithms ordinarily decimate while subsampling DECT Digital Enhanced Cordless Telecommunications A standard developed by the European Telecommunication Standard Institute from 1988 governing pan European digital mobile telephony DECT covers wireless PBXs telepoint residential cordless telephones wireless access to the public switched telephone network Closed User Groups CUGs Local Area Networks and wireless local loop The DECT Common Interface radio standard is a multicarrier time division multiple access time division duplex MC TDMA TDD radio transmission technique using ten radio frequency channels from 1880 to 1930 MHz each 3 HandyTone 386 User Manual Grandstream Networks Inc divided into 24 time slots of 10ms and twelve full duplex accesses per carrier for a
44. supports 484 response Sets the prefix added to each dialed number This parameter allows the user to configure the key to be used as the Send or Dial key Once set to Yes pressing this key will immediately trigger the sending of dialed string collected so far In this case this key is essentially equivalent to the Re Dial key If set to No this key will then be included as part of the dial string to be sent out Default is NO When set to Yes a SUBSCRIBE for Message Waiting Indication will be sent periodically If this parameter is set to Yes user ID will be sent as anonymous essentially block the Caller ID from displaying If set to Yes the configuration update via keypad is disabled NOTE Since only FXS1 has LED for indication and IVR for keypad access this field is not applied to FXS2 Default is Standard Choose the selection to meet some special requirements from Soft Switch vendors like Lucent Nortel BroadSoft etc 6 2 4 Saving the Configuration Changes Once a change is made users should click on the Update button in the Configuration page The HandyTone 386 will then display the following screen to confirm that the changes have been saved 31 HandyTone 386 User Manual Grandstream Networks Inc Your configuration changes have been saved They will take effect on next reboot Reboot Users are recommended to Reboot the HandyTone 386 after seeing t
45. tegration compactness and ultra affordability The HandyTone 386 is fully compatible with SIP industry standard and can interoperate with many other SIP compliant devices and software on the market Grandstream HandyTone 386 is a new addition to the popular HandyTone product family The new HandyTone 386 features two FXS ports each with independent SIP accounts This document is subject to changes without notice The latest electronic version of this user manual can be downloaded from the following location http www grandstream com V downloads htm HandyTone 386 User Manual Grandstream Networks Inc 2 Installation HandyTone 386 Analog Telephone Adaptor is an all in one VoIP integrated device designed to be a total solution for networks providing VoIP services The HandyTone 386 VoIP functionalities are available via regular analog telephones The following photo illustrates the appearance of a HandyTone 386 Top View Side Views RJ 11 pl V 5v 1 2A Line RJ 45 10M RJ 11 RJ 11 Ethernet LAN Port BUTTON FXS Port 1 FXS Port 2 RED LED GREEN LED Interconnection Diagram of the HandyTone 386 Internet ADSL Cable Modem or Ethernet Analog Phone Analog Phone 2 2 FXS 2 FXS I Cordless Phone Cordless Phone LINE PSTN Line A Fax Fax HandyTone 386 has two FXS ports The RJ 11 jack next to the LAN is called FXS port 2 and the RJ 11 jack on the corner is called FXS port 1 The RJ 11 jack on the side on of the HandyT
46. ur is that not only the signaling traffic but also the media traffic voice video etc crosses the OBP SBC Without an OBP SBC the media traffic travels directly between the VoIP phones Private OBP SBCs are used along with firewalls to enable VoIP calls to and from a protected enterprise network Public VoIP service providers use OBP SBCs to allow the use of VoIP protocols from private networks with internet connections using NAT PPPoE Point to Point Protocol over Ethernet is a network protocol for encapsulating PPP frames in Ethernet frames It is used mainly with cable modem and DSL services 40 HandyTone 386 User Manual Grandstream Networks Inc PSTN RTCP RTP SDP SIP STUN TCP TFTP Public Switched Telephone Network 1 e the phone service we use for every ordinary phone call or called POT Plain Old Telephone or circuit switched network Real time Transport Control Protocol defined in RFC 3550 a sister protocol of the Real time Transport Protocol RTP It partners RTP in the delivery and packaging of multimedia data but does not transport any data itself It is used periodically to transmit control packets to participants in a streaming multimedia session The primary function of RTCP is to provide feedback on the quality of service being provided by RTP Real time Transport Protocol defines a standardized packet format for delivering audio and video over the Internet It was developed by the Audio
Download Pdf Manuals
Related Search