e-Boost-40 e-Boost-60
Contents
1. Boost Set Point Approximate Boost Pressure achieved 30 0 68 bar 10 psi 68 kpa 40 1 02 bar 15 psi 102 kpa 50 1 29 bar 19 psi 129 kpa External Wastegates Please use caution Reset all Boost Set Point values to Zero 0 Follow the steps in the section 4d Setting Boost Pressure to adjust each of your Boost Set Point Valves Note e Boost cannot be used to obtain a boost pressure lower than the standard actuator setting e Boost cannot compensate for boost pressure drop at high RPM due to the turbocharger operating beyond its maximum efficiency range i e incorrect turbocharger sizing or excessive exhaust backpressure or increases in boost pressure at high RPM due to inadequate wastegate flow capacity The turbo system must maintain a steady base boost curve e Boost cannot be used with external wastegates that poor worn or non serviceable condition 4e Sensitivity The e Boost has a sensitivity adjustment that effects the way that the e Boost controls boost pressure The sensitivity is factory set to 10 this caters for the majority of turbo applications however should you feel that the sensitivity requires adjustment it can be set from 0 to 99 Refer to the table below for more detail Sensitivity too low Achieves more boost in high gears Takes longer to achieve boost set point Boost drops off at higher RPM Sensitivity correct Boost rises quickly and2. SP2 and SP3 This allows you to tailor each gate pressure to individual boost set points in order to get the most efficiency from your turbo For example GP1 is used only when 5 1 is selected GP2 is used only when 5 2 is selected and so The Gate pressure should only be set once your boost set points have been finalised do not attempt to set the gate pressure first The three gate pressures have been factory set to 0 2bar 2 9psi 20 The objective when setting gate pressure is to maximise the value without causing a boost spike Increase the gate pressure until the boost pressure overshoots the desired setting This boost spike is a result of the wastegate actuator being held closed too long Reduce the gate pressure value until this boost spike is eliminated If the gate pressure is set beyond your actual boost pressure the e Boost will reach the gate pressure once and then revert to your actual boost pressure Once the e Boost registers a vacuum the gate pressure function is reset and so on Page 10 PART NUMBER FG EBOOST ANILA e Boost 40 60 Instructions This cycle is advantageous for certain applications where a momentary spike in boost is desired To change the gate pressure value enter the boost parameter menu then scroll to GP1 GP2 or GP3 Press and hold the Mode button for two seconds press the up or down arrows to change the gate pressure value Press the Mode button momentarily and the gate pressu
3. Panel mounting bracket Secure e Boost to panel 2 M4 nuts Secure panel mount bracket 2 spring washers Use with M4 nuts 1500 mm 4mm OD Polyurethane hose Connected to back of e Boost 1 Push in 4mm hose joiner Joins 4mm polyurethane hose if cut 3mm ID Silicon hose Join polyurethane hose to intake manifold inch ID Silicon hose Join polyurethane hose to intake manifold And connect solenoid Connecting barb Connect silicon hose to Polyurethane hose 3mm Tee Piece Join 3mm ID Silicon hose to intake manifold inch Tee Piece Join 2 inch ID Silicon hose to intake manifold Small spring hose clamps Use on 3mm ID Silicon hose 5mm ID Silicon hose Connect solenoid Large spring hose clamps Use on 5mm ID Silicon hose Screw type hose clamps Use on inch ID Silicon hose 5 3mm hose reducer Reduce 5mm hose to 3mm hose 5 6 35mm hose reducer Page 2 Reduce 6 35mm 2 inch hose to 5mm hose PART NUMBER FG EBOOST ANILA 2b Mounting the e Boost e boost is not waterproof and must be mounted inside the cabin The e Boost is designed to be panel mounted with the bracket supplied Alternatively the e Boost can be mounted in a 66mm 2 5 8 inch gauge pod or pillar mount The slim 4mm OD polyurethane hose is only to be used inside the cabin of the vehicle it is not rated to withs
4. appears on the readout To store this value press the Mode button momentarily To exit the boost parameter menu press the Mode button again the e Boost will display END as confirmation of exiting the boost parameter menu This will return you to Live Mode 3e Turning the e Boost off To turn the e Boost off press and hold the Mode button for five seconds This will revert your boost pressure back to standard the unit is therefore fail safe Standard boost pressure depends on your actuator most are approximately 0 5 bar 7 psi or 50 kpa To turn the e Boost on press the Mode button momentarily the display will light up and the e Boost is on 4 SETTING UP YOUR e Boost This section outlines how to use and program the basic parameters offered in the e Boost for advanced set up refer to section 5 The diagram pictured below indicates how the menu is structured in the e Boost Up or Down Arrows Hold the Mode button Hold the Mode button and press the Down arrow and press the Up Arrow Boost Parameters SREP Pomm OBS BGR AU When in Live Mode Once To display boost set point values press the Mode button Twice To access Peak Hold Three times To clear Peak Hold Key SP1 SP2 SP3 Boost Set Point 1 2 amp 3 GP1 GP2 GP3 Gate Pressure 1 2 amp 3 SEN Sensitivity AU Auxiliary Output AL Audible Alarm BGR Bar Graph Scale OBS Over Boost Shutdown PSI KPA BAR Display Units ISP ESP Internal Set
5. butterfly Do not connect to the intake manifold as the pressure signal will have both vacuum and boost pressure WARNING Do not connect more that one standard e Boost solenoid This will overload the e Boost circuit causing permanent damage For more than two internal wastegate actuators use the Twin Solenoid Kit Part FG EBOOST TSK instructions supplied with kit to ensure sufficient flow to accurately control boost pressure Page 4 PART NUMBER FG EBOOST ANILA 2f External Wastegate Connection Most external wastegates share a similar design layout Use the diagram to help identify the and bottom port of your wastegate When pressure is applied to the bottom port of a wastegate i e underneath the wastegate diaphragm it acts against the wastegate spring and the wastegate valve opens i When pressure is applied to the port of a wastegate i e above the wastegate diaphragm its acts with the wastegate spring and helps to close the wastegate valve There two methods for connecting the e Boost to an external wastegate The method used depends the following factors size of the spring fitted in your wastegate i e The boost pressure achieved by the wastegate spring only desired level of boost pressure and the difference between this and your wastegate spring pressure size of your turbocharger and wastegate and the resulting exhaus
6. A NEW AND UN USED CONDITION WITH A DATED PROOF OF PURCHASE TO THE PLACE OF PURCHASE WITHIN SEVEN 7 DAYS FROM THE DATE OF PURCHASE FOR A FULL REFUND THE INSTALLATION OF THIS PRODUCT INDICATES THAT THE INDIVIDUAL PURCHASER HAS READ AND UNDERSTOOD THIS AGREEMENT AND ACCEPTS ITS TERMS AND CONDITIONS Happy motoring The Turbosmart Team Head Office Turbosmart Pty Limited PO Box 264 Croydon NSW 2132 Australia Ph 61 2 9798 2866 Fax 61 2 9798 2826 Email info turbosmart com au USA Office Turbosmart USA 1185 Park Center Drive Suite Q Vista CA 92081 USA Ph 760 727 7610 Fax 760 727 7963 Email sales turbosmartusa com Page 13
7. GT4 All Trac Celica MR2 JZA80 Supra Identify the hose that connects from the boost control solenoid to the wastegate actuator and block both ends of this hose Some factory hoses have a small restrictor fitted inside them if the factory hoses are reused over boosting or boost spiking may occur Turbosmart recommends using the silicon hose and reducers if necessary to connect the e Boost solenoid Secure all connections with the supplied hose clamps Page 3 PART NUMBER FG EBOOST ANILA e Boost 40 60 Instructions Connect the three ports on the e Boost solenoid according to the diagram below Port 1 vents pressure from the e Boost solenoid Connect this hose to the intake side of the turbo between the air cleaner and the inlet of the turbocharger Otherwise connect a short piece of the silicon hose and face the vent downwards to stop water or debris entering the solenoid If you have removed a factory boost control solenoid connect this hose to where the factory solenoid originally vented Port 2 Connects to the internal wastegate actuator See above if your actuator has two inlet fittings Port 3 Connects to a boost only pressure source typically from the compressor housing on the turbocharger If your turbocharger does not have this fitting connect to a boost only pressure source before the throttle body or butterfly Do not connect to the intake manifold as the pressure signal will h
8. PART NUMBER FG EBOOST ANILA e Boost 40 60 Instructions e Boost 40 v 1 49 amp e Boost 60 TABLE OF CONTENTS BEFORE YOU START IMPORTANT 5 SSINSTALLATION wesc eta a Cec sacar alate Packing List 2b Mounting the e Boost 2c Installing 2d Single Int Twin Inte 2f External 2g Two 2h Two Port 4a Over Boos 4b 4 Graph 4 Setting Ba 4e Sensitivit ADVANCE DD SETUP a 5a Setting Gate Pressure 5b Auxiliary Output 5c Audible Alarm 5 Using External Set Point Switching 5e Peak Hold Function TROUBLESHOOTING NOOO OB WW W 4 1 BEFORE YOU START IMPORTANT TIPS e Boost 40 60 Instructions PART NUMBER FG EBOOST ANILA Turbosmart recommends that your e Boost is fitted by an appropriately qualified technician Consult your local tuning specialist before setting your boost pressure setting boost beyond your engines capability can result in severe engine damage or failure Turbosmart recommends that the engines Air Fuel ratio is checked once the desired boost pressure is set any increase in boost pressure can cause the engine to run lean resulting in severe engine damage or failure Turbosmart recommen
9. Point Switching amp Internal Set Point Switching 4a Over Boost Shutdown VERY IMPORTANT order to successfully program your e Boost you MUST carefully follow this section The Over Boost Shutdown or OBS is a very important safety feature of the e Boost The OBS must be set to a SAFE level at least 0 15 bar 2 2psi or 15kpa above the highest boost pressure you want to produce The OBS is factory set to 0 48 bar 7 psi or 48 kpa so you must enter a figure in order for the e Boost to produce more than standard boost pressure The purpose of this feature is to protect the user against accidentally entering a boost set point value that is too high preventing a dangerously high boost pressure Extreme care should be taken when setting this parameter Turbosmart recommends that you seek advice from an appropriately qualified technician with regard to the OBS setting Page 8 PART NUMBER FG EBOOST ANILA e Boost 40 60 Instructions If the OBS is triggered the e Boost begins to reduce the boost pressure to half of that set in the OBS parameter Once this safe pressure is achieved the e Boost returns to normal operation To change the Over Boost Shutdown enter the user parameter menu then scroll to the OBS parameter Press and hold the Mode button for two seconds press the up or down arrow to scroll to the desired pressure Press the Mode button momentarily and the OBS value will be stored Press the Mode button again to return t
10. a higher pressure is produced the previous figure is discarded To access the peak hold you must be in live mode Press the Mode button twice to view PH parameter Note the number that appears in this parameter will be in bar psi or kpa depending on what has been set in the readout parameter see section 4b for more detail Press the Mode button momentarily to clear the peak hold memory and return to Live Mode Page 11 PART NUMBER FG EBOOST ANILA e Boost 40 60 Instructions 6 TROUBLESHOOTING The following points should be checked if you find that your engine is over boosting under boosting or the boost pressure is fluctuating erratically Please note the following checks will cure 99 of problems experienced when fitting a Turbosmart e Boost Check that the e Boost solenoid is installed correctly refer to section 2c for detail Ensure the factory boost control solenoid is not connected the hose between the pressure source and the wastegate actuator Ensure the length of the wastegate actuator rod has not been modified refer to the manufactures specifications Check to see if the e Boost solenoid is not blocked or contaminated with dirt oil build up or debris Check the joining hoses for splits cracks or loose connections and ensure they are not blocked kinked or restricted particularly if the existing hose was reused Pressure test the wastegate actuator for leakage the diaphragm or housing may be cra
11. ave both vacuum and boost pressure If you are unable to achieve your desired boost pressure it is normally due to exhaust manifold backpressure forcing the internal wastegate to open To increase your boost pressure further fit a higher pressure wastegate actuator to increase your minimum boost pressure WARNING Fitting a higher pressure wastegate actuator may cause a higher than expected increase in boost pressure Turbosmart recommends resetting the Boost Set Point values to Zero and measure the new minimum boost pressure before increasing your Boost Set Point values If you are still unable to achieve your desired boost pressure ensure that your turbocharger is correctly sized for your application 2e Twin Internal Wastegate Connection The e Boost solenoid is capable of controlling two internal wastegate actuators as typically found on most factory parallel twin turbo vehicles such as the Nissan Skyline GTR 300ZX and Toyota Soarer The solenoid is connected as per the single internal wastegate instructions above with the addition of a tee piece not supplied to connect both wastegate actuators to port number 2 If there is a fitting on both compressor housings on the turbochargers use the most convenient fitting to connect to port number 3 and block the other fitting If your turbochargers do not have these fittings internal connect port number 3 to a boost only pressure Wis source before the throttle body or
12. cked or split Ensure the smooth and free operation of the wastegate arm in the turbo exhaust housing Check that the hose between the e Boost and the inlet manifold is not obstructed broken or kinked Check that the OBS is set higher than the boost pressure you are aiming for refer to section 4a for more detail Check the Blow off Valve for leakage some are used as over boost valves Gate pressure maybe set too close to your actual boost pressure Ensure correct sensitivity setting refer to section 4e Page 12 PART NUMBER FG EBOOST e Boost 40 60 Instructions TURBOSMART ONE YEAR LIMITED WARRANTY Turbosmart is a company built on Customer Satisfaction and Service That is why all of our products go through regimented test procedures before they are packaged and shipped Turbosmart stands behind its products for one full year after purchase Terms of Warranty Service and Returns are as follows Limited Warranty Turbosmart warrants its products to be free from defects in material and workmanship under normal use and if properly installed for a period of one year from date of purchase If found to be defective it will be replaced or repaired if returned prepaid along with proof of date of purchase This shall constitute the sole remedy of the purchaser and the sole liability of Turbosmart to the extent permitted by law the foregoing is exclusive and in lieu of all other warranties or representations whether
13. connected to 12 volt negative earth electrical system All electrical connections must be soldered Refer to the following table and diagram for detail on wiring the e Boost Wire Connect to RED 12 Volts switched through ignition connect via 5 Amp fuse supplied BLACK Chassis earth or ground GREY Solenoid wire 1 connect using wire supplied polarity not important BROWN Solenoid wire 2 connect using wire supplied polarity not important YELLOW Dimmer circuit 12 Volts WHITE Auxiliary output switched to ground see diagram below GREEN External set point 2 refer to section 5d ORANGE External set point 3 refer to section 5d 3 BASIC OPERATION 3a Live Mode When the e Boost is powered up it will automatically go to Live Mode In this Mode the readout and bar graph will display accurate Live boost or vacuum readings In Live Mode you can change between three boost pressure settings called boost set points These appear on the readout as SP1 SP2 and SP3 refer to section 4d for detail When the e Boost is powered up it always defaults to SP1 To change between the boost set points simply press the up or down arrow the set point will be displayed for one second and then the readout will return to Live boost or vacuum readings 3b Boost Pressure Boost pressures are set by entering a number in each of the three the boost set points see section 4d for more detail To view the bo
14. desired pressure Note the number that appears in this parameter will be in bar psi or kpa depending on what has been set in the readout parameter see section 4b for more detail Press the Mode button momentarily and the alarm pressure will be stored Press the Mode button again to return to Live Mode 5d Using External Set Point Switching The e Boost has three different boost set points These can be triggered internally via the up down arrows or externally by grounding or earthing the green and or orange wires to the chassis The external set points are selected by earthing the appropriate wire corresponding with the set point you wish to select see the table below for detail The e Boost is factory set for internal set point switching To configure the e boost for external set point trigger enter the user parameter menu then scroll to the ISP parameter Press and hold the Mode button for two seconds press the up or down arrows to change between ISP and ESP Press the Mode button momentarily and the selection will be stored Press the Mode button again to return to Live Mode Active set point Green wire Orange Wire Set point 1 Not connected Not connected Set point 2 Earthed Not connected Set point 3 Not connected Earthed Set point 3 Earthed Earthed For further details see section 2j Wiring 5e Peak Hold Function The e Boost has a peak hold function PH that records peak boost pressure Each time
15. ds that the e Boost is not used in conjunction with any type of Draw Through Fuel System Turbosmart recommends that boost pressure is set using Dynamometer on public roads The e Boost cannot compensate for a drop in boost pressure at high RPM due to the turbocharger operating beyond its maximum efficiency range incorrect turbocharger sizing or excessive exhaust backpressure e Boost cannot compensate for increases in boost pressure at high RPM due to inadequate wastegate flow capacity the turbo system must maintain a steady base boost curve e Boost cannot be used with external wastegates that poor worn or non serviceable condition A Turbosmart Fuel Cut Defender may need to be used in conjunction with your e Boost Please check out our website at www turbosmart com au or your nearest Authorised Turbosmart Dealer for more information on Fuel Cut Defenders 2 INSTALLATION 2a Packing list e Boost 40 e Boost 60 Description e Boost e Boost solenoid Use in conjunction with e Boost M3 Screws Secure e Boost solenoid M3 Nylock nuts Secure e Boost solenoid Wiring loom Connect e Boost to vehicle Earth eyelet Connect to chassis Heat shrink Shield solder joints Figure eight wire Connect wiring loom to e Boost solenoid 1 5 Amp fuse Connect to 12 Volts see wiring 10 Cable ties Secure wiring 1
16. e vent downwards to stop water or debris entering the solenoid Connect the Bottom port on the external wastegate to the same boost only pressure source as Port 1 on the solenoid For Further information on external wastegate port identification see section 2f Usea tee piece not supplied to share the boost only pressure source if necessary If you are unable to achieve your desired boost pressure it is normally due to exhaust manifold backpressure forcing the wastegate valve open To increase your boost pressure further fit a heavier wastegate spring to increase your minimum boost pressure or use the Two Port connection method 2 as below Page 5 PART NUMBER FG EBOOST ANILA e Boost 40 60 Instructions 2h Two Port Connection Method 2 The Two Port connection method 2 is used to achieve the maximum possible boost pressure that your system can develop It is the most suitable method if you are unable to develop your desired boost pressure due to high exhaust manifold back pressure WARNING An increase in your minimum boost pressure is expected when using this method Ensure all Boost Set Point Values are set to Zero and measure the new minimum boost pressure achieved by this method of connection before increasing your Boost Set Point values Connect the three ports on the e Boost solenoid according to the diagram below 1 Connects to the port on the exter
17. expressed or implied including any implied warranty of merchantability or fitness In no event shall Turbosmart be liable for special or consequential damages This warranty is only valid on products purchased from Turbosmart Authorized Dealers Service After the warranty period has expired repair service is charged based on a minimum and maximum charge rate Contact Customer Service for current rate Returns When returning a Turbosmart product for repair it must be accompanied by a completed Customer Warranty Form and RMA number To access this form please go to our website www turbosmartonline com and you will find it on the Downloads page THE TURBOSMART PLEDGE DO NOT USE ANY TURBOSMART PRODUCT UNTIL YOU HAVE CAREFULLY READ AND UNDERSTOOD THE FOLLOWING AGREEMENT Please call if you have any questions or do not understand this agreement Refer to our brochure website or catalogue for terms and conditions and further information regarding your product Turbosmart appreciates your business and pride ourselves on our customer service We are always happy to offer you advice and will provide you with help in any way we can The purpose of this agreement is to avoid any problems or hard feelings We sometimes make mistakes as do our dealers distributors and suppliers Even customers can sometimes order the wrong parts Do not use modify install trial assemble nick drop scratch or adjust any part until you first check for any damage Damage m
18. h between the parameter and its value select SP1 by pressing the up or down arrows Step 2 To edit SP1 press and hold the Mode button for two seconds The set point value will begin to flash Step 3 Apply full load to the engine in a high gear at full throttle The Live boost pressure will be displayed on the readout Note the number that appears will be in bar psi or kpa depending on what has been set in the readout parameter see section 4b for more detail Step 4 alter the boost pressure increase or decrease the boost set point value by pressing the up or down arrow until the desired boost pressure appears on the readout Step 5 To store this value press the Mode button momentarily this will return you to the boost parameter menu To exit the boost parameter menu press the Mode button again the e Boost will display END as confirmation of exiting the boost parameter menu This will return you to Live Mode Step 6 Check that the correct Air Fuel ratio has been maintained once boost pressure is set Step 7 Repeat steps 1 through to 6 for SP2 and SP3 Page 9 PART NUMBER FG EBOOST ANILA e Boost 40 60 Instructions Internal Wastegates The table below is a guideline only to relate boost set point values to approximate boost pressures achieved when using an internal wastegate with a 0 48 bar 7 psi or 48 kpa wastegate actuator If your wastegate actuator has a higher minimum boost pressure this table will not apply
19. is steady Sensitivity too high Boost pressure fluctuates cycles or is not smooth Boost pressure overshoots set point rises too fast Note Actual boost pressure will increase slightly with sensitivity To change the sensitivity enter the boost parameter menu then scroll to SEn parameter Press and hold the Mode button for two seconds press the up or down arrows to change the sensitivity value Press the Mode button momentarily and the sensitivity value will be stored Press the Mode button again to return to Live Mode Alternatively the sensitivity can be tuned live while editing this parameter Apply full load to the engine a high gear at full throttle The Live boost pressure will be displayed on the readout Note the number that appears will be in bar psi or kpa depending on what has been set in the readout parameter see section 4b for more detail You can now alter the sensitivity in real time according to the table above 5 ADVANCED SET UP 5a Setting Gate Pressure Gate pressure control is a unique feature to the e Boost The Gate pressure function allows you to determine the pressure at which the wastegate begins to open By optimising the gate pressure and keeping the wastegate closed as long as possible your desired boost will be achieved faster and at lower RPM Substantial gains in torque will be achieved The e Boost has three Gate Pressure settings that coincide with each boost set point SP1
20. n to Live Mode 4d Setting Boost Pressure The e Boost 40 is capable of controlling boost pressures up to a maximum of 2 72bar 40psi 272kpa The e Boost 60 is capable of controlling boost pressures up to a maximum of 4 08bar 60 408kpa Boost pressure is determined by the boost set point value The boost set point value can be set from 0 to 99 and is not directly related to an actual boost pressure Boost pressure is set by increasing or decreasing the value of each of the three boost set points Increasing the boost set point will result in a higher boost pressure and vice versa The boost set point changes the effect that the e Boost has on the pressure signal going to the wastegate actuator A boost set point of will have no effect on the actuator and therefore you will produce standard boost A setting of 99 will result in the turbo producing as much boost as it can Realistically the boost set point will be somewhere in the middle of this range The e Boost can store three different boost pressure settings we refer to the different boost pressures as set points SP1 SP2 and SP3 Note SP1 SP2 and SP3 are factory set to 30 40 and 50 respectively When the e Boost is powered up it will default to SP1 we recommend that you enter a boost pressure that is used most often SP1 Step 1 To access the boost parameter menu press hold the Mode button and the down arrow simultaneously The readout will begin to flas
21. nal wastegate For Further information on external wastegate port identification see section 2f Port 2 Connects to a boost only pressure source typically from the compressor housing on the turbocharger If your turbocharger does not have this fitting connect to a boost only pressure source before the throttle body or butterfly Do not connect to the intake manifold as the pressure signal will have both vacuum and boost pressure Port 3 Connects to the port on the external wastegate For Further information on external wastegate port identification see section 2f If you are unable to achieve your desired boost pressure it is normally due to exhaust manifold backpressure forcing the wastegate valve open To increase your boost pressure further fit a heavier wastegate spring to increase your minimum boost pressure If you are still unable to achieve your desired boost pressure ensure that your turbocharger is correctly sized for your application 2i Multiple External Wastegate Connection WARNING Do not connect more that one standard e Boost solenoid This will overload the e Boost circuit causing permanent damage The e Boost solenoid is capable of controlling one external wastegate For two external wastegates use the Twin Solenoid Kit Part FG EBOOST TSK instructions supplied with kit Page 6 PART NUMBER FG EBOOST ANILA e Boost 40 60 Instructions 2j Wiring The e Boost must be
22. o Live Mode 4b e Boost Readout The e Boost readout can be configured in either Bar Psi or Kpa the default setting is in bar This allows you to tailor the readout to suit your own preference The e Boost readout is factory set to bar To change the readout enter the user parameter menu then scroll to the readout parameter Press and hold the Mode button for two seconds press the up or down arrow to scroll to the desired units kpa psi or bar Press the Mode button momentarily and the selected units will be stored Press the Mode button again to return to Live Mode 4c Bar Graph The e Boost bar graph can be configured to indicate a pressure between zero and full scale depending on your Model this will be either 2 7 bar 40 psi or 4 1 bar 60 psi The bar graph has ten segments seven green segments and three red segments When seven segments are illuminated you have reached the pressure that has been programmed in this parameter The bar graph has been factory set to one bar To change the bar graph enter the user parameter menu then scroll to the bGr parameter Press and hold the Mode button for two seconds press the up or down arrow to scroll to the desired pressure Note the number that appears in this parameter will be in bar psi or kpa depending on what has been set in the readout parameter see section 4b for more detail Press the Mode button momentarily and the pressure will be stored Press the Mode button again to retur
23. ost set point value in Live Mode press the Mode button momentarily Press the up or down arrows to view the three different boost set point values i e SP1 SP2 or SP3 Press the Mode button twice to return to Live Mode Note the boost set point value that was last viewed will be active 3c Boost Parameters To access the boost parameter menu press and hold the Mode button and the down arrow simultaneously The readout will begin to flash between the selected parameter and its value scroll up or down to the parameter you want to edit Press and hold the Mode button for two seconds and the parameter will begin to flash To change the value of the parameter press the up or down arrow until the desired value appears on the readout To store this value press the Mode button momentarily To exit the boost parameter menu press the Mode button again the e Boost will display END as confirmation of exiting the boost parameter menu This will return you to Live Mode Page 7 PART NUMBER FG EBOOST ANILA e Boost 40 60 Instructions 3d User Parameters To access the user parameter menu press and hold the Mode button and the up arrow simultaneously The readout will begin to flash between the selected parameter and its value scroll up or down to the parameter you want to edit Press and hold the Mode button for two seconds and the parameter will begin to flash To change the value of the parameter press the up or down arrow until the desired value
24. re all connections with the supplied hose clamps 2c Installing the e Boost solenoid Mount the e Boost solenoid an appropriate position in the engine bay with the screws supplied The e Boost solenoid is rated to a maximum temperature of 100 degrees Celsius 212 degrees Fahrenheit ensure that it is mounted a minimum of 250mm 10 Inches away from the heat of the turbo or exhaust manifold otherwise heat shielding maybe required 2d Single Internal Wastegate Connection Most factory turbocharged vehicles use an internal wastegate system to control boost pressure The e Boost controls boost pressure by controlling the pressure signal that the wastegate actuator receives from the turbocharger Please note that the e Boost cannot be used to obtain a boost pressure lower than the standard wastegate actuator s pressure setting If your vehicle is fitted with a factory boost control solenoid it MUST BE REMOVED from the hose that runs between the pressure source and the wastegate actuator WARNING Failure to remove the solenoid will cause erratic or fluctuating boost pressure and over boosting may occur Ensure that this solenoid remains connected to the ECU s wiring harness If the Check Engine light may be triggered The factory boost control solenoid is NOT a sensor of any kind its removal from the wastegate actuator hose will NOT cause any adverse effects Some wastegate actuators have two inlet fittings eg Toyota
25. re will be stored Press the Mode button again to return to Live Mode 5b Auxiliary Output The e Boost has an auxiliary output function designed to control an auxiliary device once a certain boost pressure is achieved i e water spray water injection or warning light This circuit must be used to control a relay with a maximum load rating of 1amp The auxiliary output is factory set to 1 bar 14 7 psi or 100 kpa To change the auxiliary output value enter the user parameter menu then scroll to the Au parameter Press and hold the Mode button for two seconds press the up or down arrows to set the desired auxiliary pressure Note the number that appears in this parameter will be in bar psi or kpa depending on what has been set in the readout parameter see section 4b for more detail Press the Mode button momentarily and the auxiliary pressure will be stored Press the Mode button again to return to Live Mode 5c Audible Alarm The e Boost has an audible alarm function that sounds the internal buzzer once a certain boost pressure is achieved This alarm can be used to confirm that full boost has been reached or as an over boost warning and can be programmed for any boost pressure The audible alarm has been factory set to 1 bar 14 7 psi 100 To change the audible alarm enter the user parameter menu then scroll to the AL parameter Press hold the Mode button for two seconds press the up or down arrow to scroll to the
26. roduct was purchased If all the above procedures are followed and the product is found to be defective in either workmanship or material Turbosmart shall either repair or replace the product at its sole discretion and sole cost This limited warranty does not cover or apply to any personal injury labor charges or any other incidental costs or damages caused by the defective product The individual purchaser acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the individual purchaser agrees to indemnify Turbosmart and to hold Turbosmart harmless for any claim related to the item of the equipment purchased Under no circumstances will Turbosmart be liable for any damages or expenses by reason of use or sale of any such equipment THIS LIMITED WARRANTY IS THE ONLY EXPRESS WARRANTY WHICH APPLIES TO TURBOSMART PRODUCT AS EXPRESSLY GIVEN IN LIEU OF ANY OTHER WARRANTY EXPRESSED OR IMPLIED INCLUDING THAT OF MERCHANTABILITY ANY IMPLIED WARRANTY INCLUDING THAT OF MERCHANTABILITY AND OR FITNESS FOR A PARTICCULAR PURPOSE IS HEREBY LIMITED BY THE SAME TERMS AND TIME LIMITATIONS SET FORTH IN THIS LIMITED EXPRESS WARRANTY AND OTHERWISE EXCLUDED EXCEPT FOR THOSE OBLIGATIONS ASSUMED HEREIN TURBOSMART ASSUMES NO OTHER OBLIGATIONS IN CONNECTION WITH THE SALE OF ITS PRODUCTS IN THE EVENT THAT THE INDIVIUDAL PURCHASER DOES NOT AGREE WITH THIS AGREEMENT THE BUYER MAY PROMPTLY RETURN THIS PRODUCT IN
27. t manifold backpressure in your system Turbosmart recommends using the Two port connection method 1 as a starting point If this connection method does not achieve the desired boost pressure fit a heavier wastegate spring to increase your minimum boost pressure or use the next connection method WARNING Fitting a heavier wastegate spring may cause a higher than expected increase in boost pressure Turbosmart recommends resetting the Boost Set Point values to Zero and measuring the new minimum boost pressure achieved by the new spring before increasing your Boost Set Point values 2g Two Port Connection Method 1 Connect the three ports on the e Boost solenoid according to the diagram below 1 Connects to a boost only pressure source typically from the compressor housing on the turbocharger If your turbocharger does not have this fitting connect to a boost only pressure source before the throttle body or butterfly Do not connect to the intake manifold as the pressure signal will have both vacuum and boost pressure Port 2 Connects to the port on the external wastegate For Further information on external wastegate port identification see section 2f Port 3 vents pressure from the e Boost solenoid Connect this hose to the intake side of the turbo between the air cleaner and the inlet on the front of the turbocharger Otherwise connect a short piece of the silicon hose and face th
28. tand engine bay temperatures The connecting barb joins the 4mm OD polyurethane hose to the thicker silicon hose This silicon hose is rated to withstand engine bay temperatures and is easier to connect to the intake manifold Route the 4mm polyurethane hose through the cabin from the e Boost mounting position to the firewall bulkhead taking care not to kink the hose If necessary cut the 4mm polyurethane hose leaving a minimum of 5Omm 2 inches of hose protruding from the back of the e Boost cup Use the supplied push 4mm hose joiner to reconnect the two ends of the 4mm polyurethane hose ensuring that the hose is pushed all the way into the base of the joiner WARNING DO NOT LOOSEN THE GLAND ON THE BACK OF THE e BOOST UNIT The 4mm polyurethane hose cannot be replaced by any other hose type or fitting Loosening the gland will cause damage to the unit rendering it inoperable If this occurs the unit must be returned to Turbosmart and repaired at the customer s expense Use the connecting barb to join the 4mm OD polyurethane hose to the 3mm ID e Boost 40 4 inch ID e Boost 60 silicon hose at the firewall bulkhead Ensure the 4mm OD polyurethane hose is pressed all the way onto the connecting barb and that the polyurethane hose does not enter the engine bay Route the silicon hose through the engine bay and connect it to pressure vacuum signal from the inlet manifold Use the supplied tee piece if necessary Secu
29. ust be reported immediately NO EXCEPTIONS If there are any components missing please contact your authorized reseller immediately upon receipt of your shipment Missing components must be reported within five 5 business days of receipt Parts returned for any reason MUST BE IN RESALABLE CONDITION It is YOUR responsibility THE CUSTOMER to carefully package any returns to avoid shipping damage Insurance is highly recommended Credit cannot be issued for damaged goods Turbosmart warranties the quality of the products it designs and manufactures to be free of defects in material and workmanship This limited warranty is extended only to the original purchaser and may not be transferred or assigned This limited warranty applies to any product which after careful inspection by Turbosmart after receipt of the product from our authorized reseller is found to have a defect in either material or workmanship Any modifications to the product will void any and all warranties and will not be exchanged Before installation check new car warranty Turbosmart is not responsible for voiding any original manufactures warranty All warranty claims must be returned to the nearest Turbosmart Office you must return the product and sales receipt at your own expense accompanied by the Customer Warranty Form stating the reason for the claim Proof of purchase must be provided with any warranty claim and will be verified with the authorized reseller from which the p
Download Pdf Manuals
Related Search