Sterling 10 led - Home Security Systems
Contents
1. Refer to the Zone Programming Status Label to see how each Set was configured by the installation engineer Setting the Panel when Mains Fails Under normal operation the panel willindicate a fault condition ifthe AC supply is disconnected It will still be possible to Set and Unset the control panel during a mains fail if allowed by the engineer and no further action is required Full functionality of the control panel is available during mains fail Silent Setting The Panel Enter and then AOO or for set required A dual tone will be heard on acceptance of the command and another dual tone will be heard when the panel is set Push To Set Set the panel in any of the above methods the panel will count down but will not set until the PTS button is pressed Final Door Set Set the panel in any of the above methods the panel will count down but will not set until the final exit door is opened then closed Omitting One or More Zones If any zones are triggered whilst in exit mode a low pitched error tone will be heard any faulty zones will be displayed in the seven segment display First check for any obvious reason for these zones to have been activated This may simply be due to a monitored door or window being left open or a pet being left in a protected area If the fault cannot be rectified it is possible to omit faulty zones but this should only be used as a last resort if the building is to be left unoccupied2. codes allow setting unsetting of the panel enabling and disabling of the door chime and viewing of the event log only 7 Segment LED Display Indicating LED SUPPLY O O i Personal 7 Set Key Fire Key ote on Key Up Key Down Key System Faults There are 4 fault codes which may be displayed automatically if detected by the Sterling 10 The user is informed of any fault via the fault LED and an error tone will be emitted every 5 seconds when the panel is in day mode press the key to stop the error tone the fault LED will remain on until the fault has been corrected To determine the fault go into the event log by entering QO al symbol followed by 1 4 will be displayed i Bell Fuse Fail Auxiliary Fuse Fail Telephone Line Fail Mains AC Fail cow Tu AC Mains Loss If the AC Mains fails and there is no power to the system Only battery power an LED light will flash with a fault tone every 5 secs Panel will automatically run off backup battery when there is a mains fail To reset the panel press Rins137 Issue 6 7 Test mode enter 96 This function performs a number of tests which are listed below The next test is selected by pressing any numeric key All LEDs are switched on except the fault LED The str
3. 10 Rins137 Issue ADI SNLVLS i A P Ce 3nd 3213935 O9 NOILVTIVLSNI NOILVTIVLSNI 5235 SNIW 1129 AV14d LAS YAWIL 321 935 SNIN 995 avs 5545 371 Hid 138 1 717139 SINIL 5 P gwsa es AYVLNAINOW A wa s YNOHVZ H JLVIGAWNWI YAdINVL 55352 V 11X43 AU LNA 3 SNLVLS ONIANINVEYSOdd ANOZ 8 Thank you for buying the Sterling 10 The Sterling panel uses the latest technology in design and manufacture As the end user of the Sterling this manual is written to help you use the functions of your alarm system enabling you to get the best out of your system Once you are familiar with the panel and its functions it is advisable to change the factory set Master and Limited User codes NOTE The fire Zone is intended as an extra feature to the alarm system and must not be regarded as a total fire protection system There are two levels of user access to the system The Master Code Code 1 access to all user functions and programming features The Limited User Codes Codes 2 to 7 6
4. Example Set panel then If error tone heard exit via normal route or If error tone heard Enter then number s of Zones to be omitted 1 to 8 then Entry Exit timer will start again then exit building by normal route Rins137 Issue 6 3 Unsetting The Panel The panel may be unset by entering the building via the entry exit route and then entering either the Master Code or any of the Limited User Codes Enter 0000000 User Code Reset After Alarm Condition Enter OOOK User code to stop alarm Enter 0000000 User code to reset teh system If the panel will not reset then your installer has enabled engineer or anti code reset please contact your installation company Duress Set Unset Enter WOOW User Code Reverse the last two digits of the code The panel will then appear normal but a Duress Code will be sent to the Central Receiving Station Personal Attack Alarm PA To Activate the Personal Attack Alarm Enter MEY Enter a user code to cancel Fire Alarm To Activate the Fire Alarm Enter SIS Enter a user code to cancel Turning Chime On and Off Panel must be in day mode Enter SO The status of the chime facility is indicated by the chime LED on the front of the control panel When the chime mode is selected a two tone chime will be produced by the internal sounder and any extension speakers when an Entry Exit zone is activated The same key sequence may be used to turn off the chim
5. e facility Reading The Event Log Panel must be in day mode Enter SO The day led will flash and the most recent event stored in the log will be displayed If the up arrow key is pressed the previous log entry will be displayed Similarly if the down arrow key is pressed the next most recent entry will be displayed The event log may be scrolled backwards and forwards using the up and down arrow keys to allow the last 100 events to be viewed To leave this function press the D key An error tone will be produced if an attempt is made to scroll outside either end of the event memory log Refer to the table opposite for the symbols stored in the event log and their meanings Activation of a programmable zone Keyswitch Activation This shows that a zone was omitted and refers to the number which precedes it in the log Keypress tamper Four attempts cause a tamper fault Keypad Personal attack activation Engineer Code Entered Keypad Fire alarm activation Set A Set B Set C Set D Unset E P F A b E d System Fault MASTER USER ONLY FUNCTIONS Event Log Reset enter O This feature will only operate if whilst programming the engineer selected the feature allowing the Master User to clear the event log Rins137 Issue 6 5
6. obe is switched on 1 2 3 The bell is switched on 4 The internal sounder is switched on To exit test mode press the 69 key again Walk Test Mode Enter SIO followed by OOOK the master code and the set option either 0 When the walk test mode is enabled the chime LED will flash If the panel is then set each active zone will cause a chime when triggered This enables all the zone configurations to be walk tested individually The walk test mode is cleared when the panel is unset The numbers of any activated Zones will be entered into the event log Zones programmed as Keyswitch zones when activated in walk test will not be entered in the event log Changing Master and Limited User Codes Master Code Enter SO followed by WOOW Master User Code factory set at 1 2 3 4 Enter 0 Enter the new code twice three tones will be heard on acceptance of each asingle low tone indicates programming not accepted Master code cannot be deleted Limited User Code Enter SO followed by 0000000 Master User Code factory set at 1 2 3 4 Enter 2 to Enter the new code twice three tones will be heard on acceptance of each single low tone indicates programming not accepted To delete a user code press the key after 2 to is entered MASTER AND LIMITED USER FUNCTIONS Setting The Panel Enter 00000090 User Code and then ABO or for set required
Download Pdf Manuals
Related Search