A.A.D. Multimode
Contents
1. OFF Goodbye followed by Vigil 2 are displayed before the AAD shuts down 4 Flight restriction for the pilot Airborne 90 ft 27 5 m fl h 2 SSP A 100 Se in a zone of 908 27 5m EK E above or below Ground zero level reference In all modes with or Ground Zero without altitude correction 90 ft 27 5 m N Vigil 2 will work correctly even when used in a pressurized cabin as long as the gt 40 P pressure differs at least 23 hPa compared to the atmospheric air pressure at take off Inside this zone the Vigil 2 is in stand by status measuring every 32 sec With gradual recalibration to the atmospheric air pressure Outside this zone Vigil 2 will go in fast measuring status measuring 8 times per sec with a fixed ground zero reference in a maximum delay of 32 sec gt Vigil 2 is the most accurate AAD on the market It becomes armed once 1000 ft above Ground zero reference is reached if no or a positive altitude correction is implemented When a negative altitude correction is implemented the Vigil 2 will become armed 1000 ft above the preset negative altitude correction also known as the new landing zone The Vigil 2 stays armed until 150 ft above Ground zero reference when no or a positive altitude correction is implemented The Vigil 2 will not activate below this altitude When negative altitude correction is implemented Vigil 22. 3 1 After take off max 32 sec above 90 ft the Vigil 2 will go in to fast measuring mode Airborne status You can notice this when the LCD pixels invert see image on page 28 gt Ifthe LCD pixels are inverted on the ground and prior to take off your Vigil 2 is Airborn and therefore not reading the correct Ground Zero reference In this case you must switch off and restart your Vigil 2 to get the correct Ground Zero reference gt BEFORE EACH JUMP check the unit carefully for any implemented mode or altitude correction in ft or m English For 2 minutes after each landing your jump information will be displayed Last FF time amp speed LCD pixels remain gt inverted This same jump information is accessible at any time displayed for 30 sec by pushing the LCD button once 3 5 9 Shut down The shut down procedure is similar to the start up procedure 21 quick press of the push button after each LED flash 4 times will shut down the Vigil 2 On the first press the SysOFF message is displayed Press the button a second and third time do this as soon as the red LED flashes Press the button as soon as the red LED flashes a fourth and last time The display will show Goodbye followed by Vigil2 for a few seconds Finally the green LED flashes very briefly and then the Vigil 2 shuts down For Example Short fash 2 OFF Short flash gt 3 lt aSys OFF
3. Connector Locking Clip Screw Connectors Stainless steel filters ST N X X Connection M cables Push button Stainless steel Control unit protection cover 2 Introduction Your Vigil 2 was designed and developed by a professional team of engineers and skydivers Its function is to cut the reserve closing loop in the event that you reach a freefall speed at an unsafe altitude The flat aluminum alloy box is exceptionally strong its ergonomic design fits easily into most current rigs A Vigil 2 installation kit pouch controller window and cutter retainer can be supplied to rig manufacturers on demand The Vigil92 can be used for three types of skydiving by pushing just one button These user programmable modes are PRO STUDENT or TANDEM The Vigil 2 also has a data recorder function black box The unit memorizes the last 16 minutes of freefall time with a maximum of 16 graphs whichever is reached first total time in freefall and total number of jumps This data can be viewed directly from the control units LCD display or it can be downloaded to a PC through an infrared communication port The infrared reader and the associated software are available as an option see page 36 9 The 2 wire technology and the Kevlar reinforced cabling were especially developed for the Vigil 2 and deliver a unique combination o
4. Each mode has its own factory settings The cutter activation data is defined by selecting an activation mode 3 3 1 PRO Mode 3 The Vigil 2 activates when it measures 1100 ft 335 meters actual altitucle between 840 ft and 1100 ft depending on body position and below until 150 ft 46 meters if the freefall speed is equal or superior to 35 m sec 78 mph or 126 km h 3 3 2 STUDENT Mode The Vigil 2 activates when it measures 1300 ft 396 meters actual altitude between 1040 ft and 1300 ft depending on body position and below until 150 ft 46 meters if the freefall speed is equal or superior to 20 m sec 45 mph or 72 km h 3 3 3 TANDEM Mode The Vigil92 activates when it measures 2300 ft 701 meters actual altitude between 2040 ft and 2300 ft dependinon body position and below until 150 ft 46 meters if the freefall speed is equal or superior to 35 m sec 78 mph or 126 km h The cutter will activate instantaneously once the pre determined activation mode parameters altitude and falling speed are reached Please take this information into consideration when determining your main canopy deployment altitudes Always allow enough time to have a Fully open main canopy approximately 1000 ft 300 meter above activation altitude 3 4 Information regarding the Activation Altitude Please be aware that the Vigil 2 functions are based on a measured air pressure and on measured time Those 2 para
5. 660 30 710 Singapore Tel 65 8431 8028 etta vigil aero Table of contents Paragraph Jd 3 3 2 3 3 3 3 4 3 5 22 324 3 5 3 3 5 4 3 5 9 3 5 6 B 3 9 8 Warning Disclaimer and limited warranty see page 37 39 Welcome to the Vigil 2 World Introduction Function General Working Principle Installation The Three Activation Modes PRO Mode STUDENT Mode TANDEM Mode Information regarding the Activation Altitude Start Up and Shut Down Procedures Start Up Display Starting Up the Vigil 2 Self Tests SETUP Menu Parameters Altitude correction Using a positive altitude correction to raise the activation altitude INFO Menu Information CONFIG Menu Configuration Choice confirmation Shut Down CO cn e co BO BP ll hl wom oi Ww o FN CO CO Paragraph 4 4 1 B 5 1 n2 5 3 9 4 9 5 5 6 6 1 1 12 ia 8 8 1 8 2 8 3 8 4 9 10 11 12 Flight Restriction for the Pilot Airborne Recommendations Vigil 2 Components Main Box Dual Battery Pack Pulses Plus Element Electronic Unit Cutter Unit Control Unit Waterproof IP68 Replacement of Parts of the Vigil 2 Replacing the Battery Pack Replacing the Cutter or Control Unit Service Card Technical Specifications Glossary Dimensions Operating Description Units and conversion factors Communication Port IR Downlo
6. seconds to confirm the Vigil 2 is ready for use Remark While the message 3 Enjoy is displayed by pushing the button you can go back to the three menus SETUP INFO or CONFIG for a possible verification or modification If no altitude correction is entered the chosen STUDENT or TANDEM mode remains displayed If an altitude correction was entered the chosen mode will be displayed as for PRO 5 for STUDENT or T for TANDEM followed by a t or sign preceding the value of the implemented altitude correction see example page 17 The value will be shown in feet ft or meters m After switch on the Vigil92 stays on for a period of 14 hours and will then switch off automatically if at ground zero reference see page 23 for more detail At the next switch on Vigil 2 will retain in its memory all of the previous settings used with the exception of the ground zero reference The ground zero reference is reset at each switch on gt P gt Vigil 2 is now ready for use and is in a stand by status While in stand by status the unit re calibrates itself every 32 sec After take off the Vigil 2 will become armed once 1000 ft above ground zero reference is reached if no or a positive altitude correction is implemented When a negative altitude correction is implemented the Vigil 2 will become armed 1000 ft above the preset negative altitude correction see page 8
7. see page 18 3 5 6 Reminder The Vigil 2 is a safety device and is NOT engineered to be used as a data logger AAD nv sa operates a policy of continuous development Therefore we reserve the right to make modifications and or improvements to any of the products described in this manual without notice trademarks mentioned in this manual are the property of their respective owners gt The Vigil 2 is delivered in a custom built case After installation of the device in the rig container this case can easily be used to carry some of your accessories such as glasses audible altimeter altimeter camera 10 SERVICE LIFE LIMIT OF VIGIL 2 UNITS The Vigil 2 has been designed for maximum 20 years of use It will do a complete check of each operating parameter each time it is switched on If a parameter is out of tolerance this will be indicated on the Control Unit display screen and the unit will not switch on 11 DISCLAIMER AND LIMITED WARRANTY THE USER MUST READ UNDERSTAND AND AGREE TO THE TERMS OF THIS DISCLAIMER BEFORE USING THE VIGIL 2 AAD NV SA intensively tests each VIGIL 2 to assure its reliability Each VIGIL 2 has passed various documented technical inspections calibration tests quality control inspections and a final functional test 7 simulated jumps in a test chamber before shipment These are all documented and available to customers However the risk of electronic mechanical or exter
8. will remain armed untill 150 ft above the preset negative altitude correction The Vigil 2 will not activate below this altitude To avoid unexpected firing of the cutter you must switch OFF your Vigil 2 before travelling in a closed vehicle car bus train due to possible air pressure variation However there is no problem travelling in an open vehicle at the drop zone altitude Prior to opening the door of an aircraft in flight while it is in the activation zone below 500 m or 1640 ft it should be determined whether or not there are any Vigils on board which are set to Student Mode Certain aircraft configurations can create a pressure spike which can activate a Vigil 2 AAD when it is set to Student Mode and the aircraft is in the activation zone 93 As long as your Vigil 2 is not measuring the switch on pressure or its Ground zero reference 90 ft 27 5 m it will stay airborne measuring 8 times sec You must ALWAYS switch off your Vigil 2 before any move to another location and switch on your Vigil 2 at the new take off zone location to implement the new ground zero reference Be aware that any implemented altitude correction will not affect the original Ground zero reference altitude It will adjust the activation altitude in function of the implemented altitude correction parameters After such a jump you need to switch your Vigil 2 off and back on again to implement the new Ground zero referenc
9. HOURS IP 68 After such immersion or contact with water the Vigil 2 built in stainless steel filter does not need to be replaced If the Vigil 2 has been in contact with salt water it needs to be rinsed with clear water After contact with water the 3 filters need to be dried with a water absorbent cloth household paper or a cotton swab Leave the device for 12 hours in an environment with a ambient temperature of 18 C 65 F before the installation in a rig IT IS MANDATORY TO SEND THE VIGIL 2 BACK TO THE FACTORY FOR AN INSPECTION OF THE UNIT BEFORE THE NEXT JUMP IN THE FOLLOWING CASES IF THE VIGIL 2 HAS BEEN IMMERSED IN SALT OR CLEAR WATER DEEPER THAN 1 8 METER 6 ft IF THE VIGIL 2 HAS BEEN IMMERSED FOR MORE THAN 24 HOURS IN WATER os A Do not open your Vigil 2 s main box case 7 Replacement of Parts of the Vigil amp 2 7 1 Replacing the Battery Pack Vigil 2 Dual Battery Pack can only be changed by A A D nv sa or Vigil America Therefore the Vigil 2 has to be returned for a battery change For Battery replacement please contact A A D nv sa or Vigil America The battery must be replaced after 10 years of use operational life 30 7 2 Replacing the Cutter or Control Unit gt We highly recommend that replacements of a Cutter or Control Unit from the Vigil 2 be done by a certified rigger or through a Vigil 2 dealer Replacing the Cutter Unit after activation or the Con
10. THE MANUFACTURER THEREUNDER ARE EXPRESSLY IN LIEU OF AND BUYER HEREBY WAIVES AND RELEASES ANY AND ALL OTHER WARRANTIES AGREEMENTS GUARANTEES CONDITIONS DUTIES OBLIGATIONS REMEDIES OR LIABILITIES EXPRESS OR IMPLIED ARISING BY LAW OR OTHERWISE INCLUDING WITHOUT LIMITATION GUARANTEES CONDITIONS DUTIES OBLIGATIONS REMEDIES OR continue next page 39 11 DISCLAIMER AND LIMITED WARRANTY continuation of page 38 LIABILITIES EXPRESS OR IMPLIED ARISING BY LAW OR OTHERWISE INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE AND IMPLIED WARRANTIES ARISING FROM COURSE OF PERFORMANCE DEALING USAGE OR TRADE WITH RESPECT TO THE MANUFACTURER S PERFORMANCE HEREUNDER AND BUYER AGREES THAT THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS INCLUDING BUT NOT LIMITED TO CONSEQUENTIAL DAMAGES SUFFERED BY BUYER DIRECTLY OR INDIRECTLY BECAUSE OF ANY DEFECT IN THE MANUFACTURER S PERFORMANCE HEREUNDER NO AGREEMENT OR UNDERSTANDING VARYING ALTERING OR EXTENDING THE MANUFACTURER S LIABILITY HEREUNDER SHALL BE BINDING ON THE MANUFACTURER UNLESS IN WRITING AND SIGNED BY THE MANUFACTURER S AND THE BUYER S DULY AUTHORIZED OFFICER OR REPRESENTATIVE IMPORTANT NOTE THERE IS A QUALITY CONTROL NUMBER HOLOGRAM 4 Alphanumeric digits ON EACH OF THE UNITS OF A VIGIL 2 Pyrotechnic Cutter Pulses Plus Element Control Unit and Main Box REMOVAL OF ANY G C HOLOGRAM STICKER OR THE BL
11. a falling speed of 78 mph or 35 m sec or greater It is well accepted that this minimum activation level must be guaranteed whatever the position of the skydiver If the skydiver is falling in a back to earth position the reading will reflect the correct pressure since the sensor is not influenced by a depression burble but if the skydiver is falling face to earth then the sensor located in the depression zone burble will read a pressure up to 10mbar lower or an altitude 260 ft or 79 m above the real altitude and will in this case activate later or 260 ft or 279 m lower i e at an actual altitude of 580 ft or 177 m above the ground level which would be too low Therefore a compensation of 260 ft or 79 m above the nominal activation altitude has been integrated into the software For example in PRO mode a programmed activation altitude of 1100 ft or 335 m has been set to ensure that notwithstanding the skydiver s body position activation will always be at a minimum altitude of 840 ft or 296 m actual altitude above the ground level Remarks e n a test chamber the activation in PRO mode will be at 1100 ft 840 ft 260 ft or 335 m 256 m 79 m as there is no depression zone burble The Vigil 2 has an opening accuracy of 65 ft or 20 m in all modes thanks to our patented Permanent Left Over Time Calculation method 3 5 Start Up and Shut Down Procedures It is imperative that the Vigil 2 be s
12. and under normal circomstances will never need replacement Pulses Plus 26 5 4 Electronic Unit The entirely automated assembly of surface mounted electronic components SMD Surface Mounted Devices is manufactured to the highest standards The SMD components assemblies are assembled with permanent electronic and optical production control equipment in order to ensure the highest level of quality and reliability equivalent to military standards The electronic unit also works as a data recorder It memorizes parameters see page 18 3 5 6 such as the total number of jumps the duration of the last freefall jump and the total freefall time This data can be viewed directly on the control unit s LCD display The Vigil 2 memory contains the graphs of the last 16 minutes of freefall and partial canopy ride and can be downloaded to a PC using the Vigil 2 communication port see page 36 9 5 5 Cutter Unit The Cutter Unit is patented and designed especially for the Vigil 2 and has a life expectancy of 20 years The cutter severs the reserve loop using a pyrotechnical cutting action with a circular knife Due to a high internal temperature it will also melt the loop to ensure its separation The cutter is completely enclosed to avoid any possible damage to the parachute If the Vigil 2 is activated for a lifesaving event a new cutter will be supplied free of charge only upon presentation of a complete Life
13. equivalent to the Vigil 2 activation altitude below 1640 ft or 500 m in STUDENT or PRO mode or below 2300 ft or 701 m in TANDEM mode with a pressure variation equivalent to or in excess of a vertical speed greater than 45 mph 20 m sec It is impossible to enter a negative altitude correction of more than 1500 ft or 500 m below mean sea level equivalent to gt 1090 mbar In this case the controller will indicate Invalid and the Vigil 2 unit will not switch on Vigil 2 Components The Vigil 2 s Dual Battery page 25 5 2 the Pulses Plus Element page 26 5 3 and the Electronic Unit page 26 5 4 are located in an unbreakable aluminum alloy Main Box page 25 5 1 Two flexible electric cables reinforced by 2 Kevlar cords ensure the junction between the main unit Main Box and the Cutter Unit page 27 5 5 as well as between the Main Unit and the Control Unit page 28 5 6 5 1 Main Box The Vigil 2 electromagnetic shield was thoroughly tested to ensure that it would function as intended when exposed to electromagnetic interference up to 100 volt m Such interference can be found in airports and aircraft The special shielding foil protects against electromagnetic interference waves produced by Radio communications Mobile phones Transponders Two connectors and three integrated stainless steel filters are fixed in the Main Box The stainless steel filter ensures protectio
14. ft 2000 m Operating range 1800 ft 600 m up to more than 100 000 ft 30 000 m Active Airborne range 1800ft 600m up to 30 000ft 9200m Operation Vigil 2 see 3 Working temperature from 13 F 25 C to 158 F 70 C 35 Life time Maximum 20 years life expectancy Maintenance No scheduled maintenance reguired In function of self tests messages during start up Waterproof IP 68 immersion at 1 8 m 6 ft for a maximum of 24 hours Stand by 14 hours Power Pack 3 6V dual lithium Vigil AA battery Life time min 2000 jumps or max 10 years 8 4 Units and conversion factors Length Ft x 0 3048 m OF 3 281 S Tt Pressure inHg x 33 86 mbar hPa or mbar hPa x 0 02953 inHg Speed mph x 1 6093 km h or km hx0 6214 mph Temperature C x9 5 32 F or L P 22xX53 95 C 9 Communication Port IR Download Box optional NATO Stock Number NSN 7025 13 119 7111 The Vigil 2 Control Unit is equipped with an infrared communication port that allows the user to download the freefall data recorded from the previous jumps An IR Download and associated management software is available as an option see your dealer for more information All of the parameters of the last 16 minutes of freefall and partial canopy ride are recorded maximum 16 jumps as well as the total 36 number of jumps and other information
15. the LCD display until the Vigil 2 is switched off or turns off automatically after 14 hours To avoid an airborne condition See page 23 for more detail of your Vigil 2 due to a difference in pressure eguivalent to more than plus or minus 90 ft 27 5 m compared to the ground zero reference pressure you must ALWAYS manually shut down your Vigil 2 at the end of the day and BEFORE leaving the drop zone 3 2 Installation The Vigil 2 has been designed to be compatible with most sport harness container systems on the market today If a suitable installation kit for an electronic AAD is not yet installed by the rig manufacturer a Vi il amp 2 Installation Kit pouc controller window and cutter retainer can be supplied and led your ontainer by manufacturer or by an AM Me rigger can be easly sewn into any harness container system designed for an electronic AAD All reserve closing loops currently on the market that are similar to Vigil Dyneema or the Spectra CSR style 9512 300 or the Cypres Loop Spectra Cord are acceptable for use by the installation of the Vigil The Vigil 2 s cutter must be positioned and rigged as specified by the urer s Instructions for 908 9 9 P 99 English 3 3 The Three Activation Modes The Vigil 2 has three activation modes that can be selected by the user The choice can be made in the SETUP menu see page 15 3 5 4
16. 11 carefully to understand this When a positive altitude correction is made the Vigil 2 will disarm at 150 ft 46 meter above the ground zero reference 16 the same altitude as when no altitude correction is applied This means on a positive altitude correction you will increase the activation window The disarming altitude of 150 ft above the ground zero does NOT increase When a negative altitude correction is applied the Vigil 2 will disarm 150 ft 46 meter above the preset negative altitude correction also known as the new landing zone It is each s individual s responsibility to make sure he or she has a fully open main canopy well A above the activation altitude We recommend allowing approximately 1000 ft between a fully open main canopy and the activation altitude This should allow enough time to deal with emergency procedures if necessary and prevent a possible two canopy out situation The possibility to raise the activation altitude and keep it until manually changed in the setup menu has always been in all Vigil AAD s produced since 2003 Vigil 2 in PRO settings without altitude correction Vigil 2 in STUDENT settings without altitude correction Vigil 2 in Tandem settings without altitude correction Vigil 2 in PRO settings with positive altitude correction of 100 meters Vigil 2 in STUDENT settings w
17. A A D Multimode NATO Stock Number NSN 1377 13 121 8660 Vigil 2 User s Manual US v 2 0 3 June 2015 A Please carefully read and ensure that you fully understand A this user s manual before any use of the Vigil 2 YOU MUST ALSO READ FULLY UNDERSTAND AND AGREE TO THE TERMS OF THE DISCLAIMER AND LIMITED WARRANTY PRIOR TO USING THE VIGIL 2 IF YOU DO NOT FULLY UNDERSTAND AND AGREE TO ALL OF THE TERMS OF THE DISCLAIMER AND LIMITED WARRANTY YOU MUST NOT USE THE VIGIL92 YOU MAY RETURN IT IN ITS ORIGINAL PACKAGING FOR A FULL REFUND YOUR USE OF THE VIGIL 2 IN THE EQUIPMENT YOU USE FOR MAKING A PARACHUTE JUMP IS CONCLUSIVE PROOF THAT YOU AGREE TO ALL OF THE TERMS OF THE DISCLAIMER AND LIMITED WARRANTY The Vigil is endorsed by United Panachure SS Technologies PARACHUTES de FRANCE FIRE Ire P Sky Piue parachutesustems Thomas Sports dud C IM SA lerodyne Jm SHACK P SSS MIRAGE S nv sa Advanced Aerospace Designs AAD nv sa Advanced Aerospace Designs Bld A Reyers 193 B 1030 Brussels Belgium Tel 32 0 2 732 65 52 Fax 32 0 2 736 06 27 e mail info vigil aero website www vigil aero Vigil America Inc 1400 Flightline Blvd Suite C DeLand FL 32724 USA Tel 1 386 736 8464 Fax 1 386 736 8468 e mail candace vigil aero Vigil Far East Nam Fong Industrial Building Block 1 227 RIC Avenida Vencelau de Morais Macau Hong Kong Tel 852
18. EAST 32 SECONDS THIS ALLOWS VIGIL 2 TO CHANGE FROM STAND BY TO FAST MEASURING STATUS In freefall the Vigil 2 starts to continuously calculate the leftover time to reach the activation altitude When this altitude or lower is reached by the jumper at equal or superior speed compared to the factory set parameters the cutter of the Vigil 2 will instantly fire and cut the closing loop of your emergency parachute lt 0 002 sec An altitude correction allows you to implement a positive or negative altitude difference between the departure and landing levels from 6000 ft to 6000 ft or from 2000 m to 2000 m in steps of 150 ft or 50 m The Vigil 2 takes this altitude correction into account to calculate the new activation altitude This principle also allows you to modify the activation altitude permanently if the airport where you take off and the landing zone are at DIFFERENT altitudes or if there is a hillock near the drop zone Each mode PRO STUDENT or TANDEM has its own factory set activation altitude and speed Choice of mode can be done in the SETUP menu see Page 9 3 3 During your aircraft ascent the Vigil 2 s red LED will briefly flash three times when it passes through its pre set activation altitude The Vigil 2 will automatically remain ON for 14 hours it may of course be switched off manually before that time The selected activation mode PRO STUDENT or TANDEM will remain visible on
19. IG menu see page 19 3 5 7 to set the required units U S or metric before other settings 3 5 4 SETUP Menu Parameters Altitude correction The SETUP menu enables you to implement a positive or negative altitude correction in feet or meters between the departure and arrival ground levels as well as select the desired mode PRO STUDENT TANDEM see example page 17 It is possible to enter the SETUP menu at the end of the self testing sequence To do this press the push button as soon as the display shows SETUP and the red LED flashes It is possible to implement an altitude correction from 6000 ft to 6000 ft or from 2000 m to 2000 m To enter or modify a positive or negative altitude correction press the push button while Alt Cor appears The arrow facing up corresponds to an increase of the altitude value and the arrow facing down to a decrease of the 15 altitude value The correction is made in increments of 150 ft or 50 m when the Vigil 2 is set in meters Press the push button until the desired positive or negative altitude correction is achieved For example 100 m for higher landing zone compared to the take off zone and 100 m for a lower landing zone When the required altitude correction is displayed wait for a few moments and the mode selection PRO STUDENT TANDEM will appear on screen A Important note f you land at a different altitude than your GROUND ZERO
20. Saving Report approved by Vigil This document can be downloaded from the Vigil website http www vigil aero 21 gt The cutter is field rigger replaceable see page 30 7 2 gt Some countries regulations require a certified rigger to do such replacements In this situation you must adhere to your country s rules gt A Dual Cutter can be supplied for reserve containers closed with a dual pin 28 5 6 Control Unit The control unit is composed of a reversible display a red LED that sets the timing of the start up and shut down procedure a green LED that confirms the end of the start up procedure and an orange push button situated in the standard configuration on the right of the display The 26 x 96 dots display on the control unit allows clear alphanumerical communication with the parachutist it is protected by a special scratchproof coated screen and a stainless steel cover The red LED is also used as transmitter for the infrared communications port see page 36 9 Stand by status Normal display of the control unit on the ground not airborne Stainless steel Red LED LCD 26 x 96 dots protection cover Airborne Status Inverted display of the control unit airborne in fast measuring mode 6 Waterproof IP 68 6 1 The Vigil 2 has been designed to resist water immersion of up to 1 8 meter 6 ft depth for a maximum of 24
21. UE SEALING PAINT EXCEPT BY THE MANUFACTURER VOIDS THE WARRANTY N NEVER JUMP WITH A BLANK SCREEN N 39 M I 01 01 Ugg88 888 OA SLIN0O O dnjag Jo I x J e p JnoA 1J nsuoo Em are UO YONMAS JOU ISTA 15 mg MD Qt amp amp M NN gt 2 o un ueuo eouenbes 1ejeujeJeg dew 2 lt r VIGIL 2 c 01 09 edy 8888 00 pausiun ywy 888 5888 TI I 09 juapnjs H Old dun oyu 148888 X 88g 8 1994 19 9 A JO
22. ad Box Service life limit of Vigil 2 units Disclaimer and limited warranty Road Map Grafcet Parameter Sequence Flow Chart Page 22 24 24 25 25 26 26 27 28 29 29 29 30 32 34 34 35 35 35 36 37 37 41 WARNING SKYDIVING IS A DANGEROUS ACTIVITY AND YOU RISK MINOR OR SERIOUS PERMANENT INJURY OR DEATH EACH TIME YOU SKYDIVE THE CORRECT USE OF THE VIGIL AAD MAY REDUCE THIS RISK HOWEVER THERE ARE SITUATIONS IN WHICH A VIGIL AAD MAY NOT REDUCE AND MAY ACTUALLY INCREASE THE RISK THE VIGIL IS A BACKUP DEVICE WHICH MAY OR MAY NOT SAVE YOUR LIFE AND IT IS IMPORTANT TO NEVER RELY ON THE VIGIL AS A LIFESAVING DEVICE PRIOR TO USING THE VIGIL IT IS IMPORTANT TO READ THE VIGIL 2 USER S MANUAL VERY CAREFULLY ALWAYS OBSERVE ALL WARNINGS AND FOLLOW ALL MANUFACTURER S INSTRUCTIONS RECOMMENDATIONS AND SAFETY PROCEDURES ALWAYS FOLLOW CORRECT OPENING PROCEDURES AND IF NECESSARY EMERGENCY PROCEDURES NEVER SKYDIVE UNLESS YOU ARE FULLY TRAINED AND COMPETENT IN THE USE OF ALL OF YOUR EQUIPMENT INCLUDING THE VIGIL The Vigil92 is equipped with an integrated Piezo resistive barometric pressure sensor Do not expose your Vigil 2 to pressures above 3000 hPa 45 5 psi or to temperatures above 158 F 70 C 4 The battery pack is designed to operate within a temperature range from 13 F to 158 F 25 C to 70 C DISCLAIMER AND LIMITED WARRANTY see pages 37 39 gt You must switch ON your V
23. choose the type of measurement units you wish to display reverse the display characters and adjust the contrast of the display To enter into the configuration menu press the push button as soon as the display indicates CONFIG 19 and the red LED flashes Initially the display indicates Feet or Meters depending on the existing configuration To change the measurement unit press the push bution English You can choose U S or Metric by pressing the push button Fahrenheit mph inches of mercury or Celsius km h hectoPascal Press View to choose to view the display in its normal configuration or flipped 180 The contrast can be adjusted by pressing the push button when Contrast is displayed in accordance with the up and down arrows it will not fade out Once the CONFIG menu is completed the Vigil 2 is operational and will keep in memory the chosen configuration For example Dip CONFIG displayed Choose between Feet or Meters 3 Push Choose between U S or Metric Fahrenheit mph inches of mercury or Celsius km h hectoPascal Choose between normal or reversed display View or Contrast contrast All of the parameter sequences are described in the Parameter Sequence Flow Chart see page 40 12 3 5 8 Choice confirmation 20 The green LED flashes five times and the message 3 Enjoy is displayed for a few
24. e altitude and manually remove the previous altitude correction If no longer reguired If decending in an aircraft with an armed Vigil 2 the pilot must be advised of the status of your Vigil 2 to limit his descent rate according to the mode less than 20m sec 3960 feet per minute for STUDENT and less than 35m sec 6864 feet per minute for PRO or TANDEM and in the activation zone this is especially important for Vigil 2 programmed in STUDENT mode In these circumstances we recommend that the Vigil 2 be switched off if possible 24 4 1 V v v v v gt 9 Recommendations To get the correct GROUND ZERO REFERENCE you must only switch the Vigi2 ON once you arrive at the take off zone Afterwards enter any altitude correction if needed When the elevation of your landing zone differs by more than 90 ft 27 5 m compared to your initial take off zone and this landing zone becomes your new take off zone it is necessary to switch your VigiP2 off and back on again so that it can re calibrate itself Check the display carefully before each jump to verify that its settings are correct Manually shut down your Vigil 2 after the last jump of the day The Vigil 2 will shut down automatically 14 hours after its start up To avoid undesired Vigil 2 firings if you enter a plane with a pressurized cabin please notify the pilot that he is not allowed to do any pressurization tests to pressures
25. f strength and flexibility The gold plated contacts and the locking system with a special locking clip on the connectors ensure optimal connection reliability in all circumstances The control unit is equipped with a 26 x 96 dots LCD display which allows interactive and clear communication with the parachutist is protected by a special anti scratch coating and a stainless steel protection cover The electromagnetic shield protects the Vigil 2 from electromagnetic interferences such as those found in airports and airplanes see page 25 5 1 English 3 Function 3 1 General Working Principle The Vigil 2 must only be turned on at ground level it will calibrate itself every 32 sec progressively to the current ground elevation pressure This is the GROUND ZERO reference Once your Vigil 2 is on at each take off it will become armed once 1000 ft above ground zero reference is reached if no or a positive altitude correction is applied When a negative altitude correction is set the Vigil 2 will become armed 1000 ft above the preset negative altitude correction so if the negative altitude correction is over 1000 ft the Vigil 2 will become armed maximum 32 sec after you have reached 90 ft above the GROUND ZERO reference take off location WHEN A NEGATIVE ALTITUDE CORRECTION IS APPLIED IT IS MANDATORY THAT THE AIRCRAFT REMAINS AT LEAST 90 ft ABOVE THE GROUND ZERO REFERENCE take off zone FOR AT L
26. fter the third flash of the red LED The Vigil 2 will then automatically start its self test sequence In short Hello followed by Vigil 2 appears flash gt 2 VIGIL 2 Hasho 3 VIGIL 2 Flasho 4 BVIGIL 24 Start of self tests BAT OK The startup and shut down procedures listed in this manual have been established to reduce the risk of an unwanted start up or shut down sequence and to ensure that the Vigil92 cannot be turned on or off by accidentally pressing the push button 3 5 3 Self Tests The Vigil 2 automatically goes through a complete test sequence each time it is switched on It verifies that the battery pack the cutter and the electronic circuits main functions are in proper working order English The following messages are shown Bat OK The battery pack is functioning properly Cut OK The cutter resistance is tested O K Ctrl OK The electronic circuits are functioning properly If an error is detected the following messages may be shown Bat Low Low Battery the Vigil 2 is still operational but the dual battery pack must be replaced as soon as possible see page 29 7 1 Bat Rpl The dual battery pack must be replaced the Vigil 2 will not switch on see page 29 7 1 Cut Err Cutter resistance is out of tolerance the Vigil 2 will not switch on Ctrl Err A discrepancy in one of the electronic circuits is observed unit will
27. gram sticker with a new number When the replacement of a subpart has been done it is mandatory to proceed as follows 1 Fill out the Service Card 2 Send a copy of the Service Card to A A D nv sa by fax 32 2 7360627 or via e mail to service vigil aero 3 Hand it to the owner of the Vigil Make sure that the owner keeps the original Service Card with the original Test Certificate card and the documents of the rig This procedure is important for our After Sales Service as it allows us to update our files and to guarantee the replacement part with a 2 year warranty Vigil AAD Service Card This spare part has been tested in accordance with Advanced Aerospace Designs manufacturing specifications valid on the Date Of Manufacture D O M To validate your customer s warranty please fill in and fax us a copy of this card 32 2 736 06 27 QC Nr 562 6 Battery D O M Mounted on the Unit Cutter 03 4 CNW A Cutter 7 D O M _ QA AV B _ Q To be completed B B by the rigger or Gras BE person who performed Testing Location Brussels Belgium Date the handling Tested ByDenis Van den Broeck Signature Technical Support A VASC Vigil Approved Service Center DU m Doha ms fey 33 34 9 Technical specifications 8 1 Glossary Electromagnetic shielding A special metal shield that protects the electronic circuits from electromagne
28. igil 2 ONLY at the take off zone reference altitude or ground zero gt you intend to change to a different drop zone switch OFF your Vigil amp 2 before travelling and switch it back ON at the new drop zone before take off gt Before each jump it is essential to visually check your LCD screen to ensure its functionality its activation mode PRO STUDENT or TANDEM and its pre selected parameters altitude correction in feet or in meters are correctly set NNEVER JUMP WITH A BLANK LCD SCREEN ON YOUR Vigil 2 N 1 Welcome to the Vigil 2 World We congratulate you on your purchase of today s most sophisticated and modern multimode Automatic Activation Device It is a revolutionary safety device with no imposed maintenance schedule The Vigil 2 will automatically check all of its functional features each time it is switched on The Vigil 2 will detect any anomalies by itself Should an abnormality be found the controler will display an error message see page 13 3 5 3 and the Vigil 2 unit will not switch on In this case the Vigil 2 needs to be analyzed by an authorized dealer or sent back to the factory for analysis The Vigil 2 is designed for a life expectancy of maximum 20 years from the date of manufacture The above life expectancy is based on the fact that the cutter the Pulses Plus element and the electronic components have been designed for a functional lifetime of 20 years The Vigil 2 i
29. ith negative altitude correction of 600 feet an Vigil 2 in Tandem settings with positive altitude correction of 450 feat 3 5 6 INFO Menu Information This menu allows you to display your Vigil 2 s reference parameters version date of manufacture and serial number data of previous jumps as well as temperature and atmospheric pressure To enter the INFO menu press the push button as soon as the display shows INFO and the red light flashes These parameters are in clear language in function of the chosen units and as follows see page 19 S 3 5 7 for example 26 06 week 26 in 2006 TJ 8888 Total Jumps Total number of jumps with this unit 18 88m88s hours followed by minutes and seconds 888 km h and maximum speed of the last freefall displayed in km h or mph T 88 C or 88 F Temperature of 152 main unit F or C depending on the configuration 88inHg or 8888hPa Atmospheric Pressure in inches of mercury inHg or hectopascal hPa Certain special models may be equipped with custom built or experimental software In such cases a specific identification logo on the cover is used and a specific manual will be issued The information supplied for those units could be different from that supplied for the Vigil 2 units As reference Standard logo Xtreme logo 3 5 7 CONFIG Menu Configuration This configuration menu allows you to
30. meters permit the calculation of the exact altitude in function of the registered air pressure as well as the vertical speed related to a pressure variation in a certain period of time For information The Vigil 2 is able to register pressure differences of 0 1 hPa which is equivalent to an altitude difference of only 2 6 ft or 0 8 meter Important note The registered pressure by the sensor will vary according to the body position of the skydiver face to earth or back to earth up to 10 hPa mbar which is equivalent to 260 ft 80 m 10 Example Let s consider two skydivers in free fall at exactly the same altitude but one is falling back to earth and the second one is falling face to earth The influence of their falling position on their respective AAD reading is as follows I Back to earth Face to earth Depression zone burble AAD or pressure sensor No influence located in depression zone Both at the same altitude Y burble y ee P sss Pressure sensor location Pressure X hPa 10 hPa Pressure X hPa Vigil92 in depression zone will register an up to 10 hPa lower pressure notwithstanding they are at the same The stated or real altitude gt Y ft or m level The stated altitude Y 2260 ft or 80 m Vigil 2 will register a pressure of X hPa Conclusion If the Vigil 2 is set in PRO mode it will activate at a minimum altitude of 840 ft or 256 m above the ground at
31. n against pollution such as the intrusion of dust and provides a instant transfer of outside air pressure to the pressure sensor keep it clean and dry NEVER OPEN THE MAIN BOX OF THE VIGIL 2 Opening the main box of Vigil 2 voids all warranties 5 2 Dual Battery Pack NATO Stock Number NSN 6130 13 119 7106 The battery pack is composed of 2 lithium AA cells in the lower half of the case It is not subject to any memory effect and is extremely long lasting The battery pack works at a temperature range from 13 F to 158 F or from 25 C to 70 C The use of low consumption components in conjunction with a sophisticated power management program has significantly improved the battery s life span The battery s life span is expected to be a minimum of 5 years or 2000 jumps When the Bat Low or Bat Rpl message appears the battery pack needs to be replaced see page 29 7 1 Regardless of the above stated life span the battery pack must be replaced after 10 years of use max operational lifetime 25 5 3 Pulses Plus Element Dual Battery Pack TADIRAN IES The Pulses Plus technology supplies the Lithium Battery 3 6V S1P2 SL high peak current necessary for the cutter to la CAN nos ors open neat go o not recharge oc activate and cut the loop in less than T 2 milliseconds This element has an operational lifetime of M mas 20 years
32. nal factors causing a malfunction or failure cannot be totally excluded BUYER UNDERSTANDS THAT BECAUSE OF THE UNAVOIDABLE DANGER ASSOCIATED WITH THE USE OF A PARACHUTE SYSTEM SKYDIVING AND THE USE OF A VIGIL 2 THE MANUFACTURER MAKES NO WARRANTY WHATSOEVER EXPRESS OR IMPLIED ARISING BY LAW OR OTHERWISE EXCEPT THAT THE MANUFACTURER WILL REPLACE OR REWORK DEFECTIVE PARTS FREE OF CHARGE WITHIN TWO YEARS FROM THE DATE OF PURCHASE OTHER THAN THE FOREGOING THE VIGIL 2 IS SOLD WITH ALL FAULTS AND WITHOUT ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR USE continue next page 38 11 DISCLAIMER AND LIMITED WARRANTY continuation of page 37 THE MANUFACTURER DISCLAIMS ANY LlABILITY UNDER THE LAW IN TORT OR OTHERWISE FOR DAMAGES DIRECT OR CONSEOUENTIAL INCLUDING BUT NOT LIMITED TO DAMAGES FOR PERSONAL INJURIES WRONGFUL DEATH PROPERTY DAMAGE AND LOSS OF USE OF EOUIPMENT RESULTING FROM ANY MALFUNCTION OR FROM ANY DEFECT IN DESIGN MATERIAL WORKMANSHIP OR MANUFACTURING WHETHER CAUSED BY NEGLIGENCE ON THE PART OF THE MANUFACTURER OR ANY MANUFACTURER OF ANY PART ACCESSORY COMPONENT OR APPLIANCE MADE A PART OR APPURTENANT TO THE VIGIL 2 BUYER BY USE OF THE VIGIL 2 AND OR ALLOWING IT TO BE USED BY OTHERS WAIVES ANY LIABILITY ON THE PART OF THE MANUFACTURER FOR PERSONAL INJURIES WRONGFUL DEATH LOSS OF CONSORTIUM PROPERTY DAMAGE AND LOSS OF USE OF EOUIPMENT THE WARRANTIES SET FORTH ABOVE AND THE OBLIGATIONS AND LIABILITIES OF
33. not switch on If one of these messages is displayed except for Bat Low the startup procedure will end and the Vigil 2 will switch itself off If the Bat Low message appears the battery pack must be replaced as soon as possible see page 29 7 1 If the Bat Rpl message appears the battery pack must be replaced prior to the next jump see page 29 7 1 If the Cut Err message appears the cutter unit must be replaced prior to the next jump see page 30 7 2 A new cutter will be supplied free of charge if a completed Life Saving Report is posted and approved see our website http www vigil aero on the download page gt We recommend that Vigi 2 parts be replaced by a certified rigger or by a Vigi approved expert The regulations in some countries require a certified rigger to do such replacements The user may not have authorization to replace the cutter or controller unit In such situations you must adhere to your country s rules A If the Ctrl Err message appears due to a failure in the electronic circuits you must send the Vigil 2 back to your dealer or to the factory for a complete checkup before the next jump DO NOT try to restart the Vigil 2 again This first test procedure is followed by 3 different menus SETUP INFO and CONFIG see page 8 3 Recommendation if the Vigi2 is not yet configured to your standard measurement units go first to the CONF
34. please be aware that the original GROUND ZERO reference will remain in the Vigil s memory and will be applied to all following jumps as long as your Vigil 2 has not been switched off Your Vigil 2 MUST be reset after you have landed and prior to your next jump at the other drop zone By switching your Vigil 2 off and back on again the Vigil 2 will reset itself A Please remember that any implemented Alt Cor will remain in the Vig 2 memory and will only be cancelled if manualy reconfigured in the SETUP menu 3 5 5 Using a positive altitude correction to raise the activation altitude As stated on page 9 3 3 in PRO settings Vigil 2 activates at a measured altitude of 1100ft 335 meter actual altitude of 840 1100 feet depending on body position To increase safety margins an altitude correction can be performed see page 15 3 5 4 Some important points to remember Once an altitude correction is applied this will stay in the Vigil 2 s memory until you manually remove it in the SETUP menu When you raise the activation altitude always allow enough time to have a fully open main canopy approximately 1000 ft above your new activation altitude During a slow opening it may take longer until you have a fully open main canopy whitch may bring you closer to the activation altitude you choose A Vigil 2 will activate at the measured altitude it is set in Please read page 9 10 and
35. s very user friendly It can be used in your choice of 3 activation modes PRO STUDENT or TANDEM The Vigil92 an ALL IN ONE Automatic Activation Device AAD will also work in U S or metric standards units When traveling on any commercial flight with your Vigil 2 this manual as well as the Vigil X Ray Card should accompany you It contains explanations that will be useful to the airport security staff The most recent manual is available on the Vigil website at htto Avww vigil aero on the download page The Vigil 2 is in principle a last resort safety device which may or may not save your life It has never been intended to be and is not to be used as a parachute s primary opening system The procedures written in this manual must be followed to ensure that the Vigil 2 functions properly Incorrect setup or use can lead to improper functioning of the Vigil 2 A skydiver should always adhere to all rules and regulations set by his her country s skydiving federation The use of a Vigil 2 AAD does not exempt the parachutist from performing proper emergency procedures ALTHOUGH VIGIL s HAVE SAVED MANY LIVES NEVER RELY ON THE VIGIL TO SAVE YOUR LIFE IT MAY NOT DO SO IN SOME SITUATIONS Blue sealing y paint Main Box Main Box hologram Pyrotechnic cutter Red IR LED receiver Green LED
36. tic waves to avoid malfunctions of the device by electromagnetic interference from radars cellular phones Cutter Unit A cutting system that acts by a pyrotechnical double cut of the loop inside the reserve container o Port Transmitter receiver of infrared signals that allows a bidirectional exchange of data between two evices Kevlar Non elastic carbon fiber used to reinforce the cables It prevents direct traction on the electrical connections and it reinforces mechanically the junction cables of the Control Unit and the Cutter LCD Liquid Crystal Display The LCD is used to visually convey information from the Control Unit to the user LED Light Emitting Diode A LED is used to flash during the start up and shut down procedures of the device SMD Surface Mount Device Small electronic components manufactured to be of reduced size and low power consumption Such technology allows the electronic circuit to be mounted automatically which gives very reliable and compact electronic systems LC A plastic molded clip that prevents the Cutter or Control Unit a from unscrewing nent or accidentally from the main box 8 2 Dimensions Main Box 102 x 51 x 20 mm Cutter Unit 55 9 mm Standard Wire Length Cutter unit 600 mm Control Unit 63x 18x 11 mm Control unit 900 mm Total Weight 400 g Volume 130 cm 8 3 Operating description Altitude correction from 6000 ft 2000 m up to 6000
37. trol Unit if necessary is a simple and fast process which can be performed quite easily by your rigger or through a Vigil 2 dealer Every dis assembling operation must be done with the Vigil92 switched off see page 21 3 5 9 How to be sure the Vigil 2 is switched off 1 Press on the push button only one single time to display Hello on screen 2 Wait until a blank screen appears again proves that the unit is switched off 3 Perform procedure as shown and described on page 31 4 Perform a new start up procedure for final check see page 13 3 5 2 9 Fill in the Service Card see pages 32 amp 33 7 3 Unscrew Connectors Locking Clip CLC Remove Connectors Manually unscrew Locking Clip CLC connector of spare unit for example cutter V Reconnect and manually tighten the new spare unit Cutter or Control unit VI Place Connectors Locking VII After CLC is well VIII Check if CLC is closely Clip CLC and check if positioned secure with attached to Main Box no CLC locks both connectors original screw space between both objects English 31 32 7 3 Service Card Every replacement part comes with a Service Card Vigil AAD Service Card with a hologram number and a date of manufacture DOM for the cutters the software version for the control units Others can be for example a software upgragde The card is identified with a holo
38. witched ON at the ground level of your take off zone This becomes the GROUND ZERO reference altitude Your Vigil 2 will recalibrate itself for variation in the atmospheric pressure gt Attention If there is a rapid change in atmospheric pressure more than 10 hPa it is recommended that you shut down and restart your Vigil 2 to ensure optimal precision AN Never switch on your Vigil 2 in an aircraft 12 3 5 1 Start Up Display In its standard configuration the Vigil 2 is used with the orange push button situated at the right side of the display The red LED is positioned in the upper corner and indicates the timing of the start up procedure The green LED is situated in the bottom corner of the controller and confirms the end of the start up procedure gt The Vigil 2 s display is reversible see page 19 3 5 7 view mala 3 5 2 Starting Up the Vigil 2 The Vigil 2 becomes operational after pressing the orange push button four times These short presses must be done immediately after each flash of the red LED After the first push hold for 1 or 2 seconds the Hello message is shown If no message appears please repeat the previous operation Hello is immediately followed by Vigil 2 on the LCD Press the push button immediately after the red LED first flashes Press the push button immediately after the second flash of the red LED Press the push button immediately a
Download Pdf Manuals
Related Search