User manual - produktinfo.conrad.com
Contents
1. effectiveness but you do increase the risk of skin reactions Continue using the appliance for at least 6 months as hair regrowth can still decrease over the course of this period Also take into account the other solutions to this problem Do not use the appliance if your body hair is light blond red grey or white Do not use the appliance either if you have dark skin Consult the body hair and skin colour table in the Quick Start Guide 24 ENGLISH Problem Possible cause Solution Hair starts to You did not make For proper hair removal results you have to make overlaps grow again in enough overlaps when you use the appliance See chapter Using the appliance some spots on the when you used section Subsequent use step 4 treated areas the appliance Hair starts to grow This is normal It is part ofthe natural cycle of hair growth again as part of that hair starts growing again The hairs that come back the natural cycle of however tend to be softer and thinner hair growth The appliance The appliance is Contact the Consumer Care Centre in your country your does not work defective Philips dealer or a Philips service centre PHILIPS OL 100 recycled paper amp 100 papier recycl www philips com 4222 100 0513 22. Intense Pulsed Light technology works Hair growth Hair growth rates differ from person to person depending on age metabolism and other factors However everyone hair normally grows in 3 phases 1 Growing phase anagen phase The hair grows actively from the root In this phase the concentration of Re melanin is highest Melanin is responsible for the pigmentation of the hair Melanin concentration is also the determining factor for the efficacy of the Intense Pulsed Light technology Only hairs in the growing phase are susceptible to treatment with light 2 Degradation phase catagen phase Hair growth stops and the root shrinks before the hair sheds 3 Resting phase telogen phase The old hair separates from its hair follicle and sheds The follicle remains at rest until the biological clock tells it to become active again and grow a new hair m mi m m m m a Im ua Working principle The appliance works by heating up the hair and root beneath the skin The melanin in the hair and hair root absorbs the released light pulses The darker the colour of the hair the more light can be absorbed This process stimulates the hair to go into the resting phase In between treatments hair sheds naturally and regrowth is inhibited Hairs can take one or two weeks to shed Optimal hair removal cannot be obtained with a single session since only hairs in the growing phase are susceptible to treatment with li
3. with reduced physical sensory or mental capabilities unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with he appliance The appliance is not intended for children under the age of 15 years Teenagers aged between 15 and 18 years can use the appliance with he consent and or assistance of their parents or the persons who have parental authority over them Adults from 19 years and older can use he appliance freely Only use the adapter supplied Do not use the appliance or the adapter if it is damaged The adapter contains a transformer Do not cut off the adapter to replace it with another plug as this causes a hazardous situation fthe adapter is damaged always have it replaced with one of the original type in order to avoid a hazard Do not use the appliance if the glass of the light exit window is broken ake sure nothing obstructs the air flow through the ventilation slots ever subject the appliance to heavy shocks and do not shake or drop it f you take the appliance from a very cold environment to a very warm environment or vice versa wait approximately 3 hours before you use it Store the appliance in the pouch supplied so that it does not become dusty Never leave the appliance unattended when it is switched on Always switch off the appliance after use ENGLISH 9
4. Do not expose the appliance to direct sunlight or UV light for several hours to prevent damage Do not flash against any other surface than the skin This can cause severe damage to the body attachment and or the light exit wi Only flash when the appliance is in contact with skin Caution ever use the appliance around the eyes and near the eye avoid the risk of eye damage ndow brows to Use this appliance only at settings suitable for your skin type see the able in section Recommended light intensities of chapter for use Use at higher settings than those recommended can increase he risk of skin reactions and side effects Preparing This appliance is only intended for removing unwanted human body hair from areas below the neckline Do not use it for any other purpose ake sure the skin in the area to be treated is clean dry and free from may not flash or may flash unintentionally creams lotions and other cosmetics If the skin is not clean and dry the integrated safety system may not work as intended and the appliance Keep the following things in mind to avoid compromising the lifetime of your Philips Lumea Esse Do not expose the appliance to amb 15 C or higher than 35 C during use The appliance is equipped with a buil appliance overheats it does not flash Then let it cool down for another 10 ient temperatures lower but let it cool down for approx 15 mi y
5. areas may require different light intensities see to the table below To prevent skin reactions see chapter Using the appliance section Possible side effects and skin reactions Recommended light intensities 1 5 In the table below x means that the appliance is not suitable for you Note The colour of your skin may change for example because your skin has been exposed to tanning lt may then be darker than during the previous treatment Therefore it is important that you check the setting to be used before every treatment and per area Some areas may be darker than others Body hair colour Dark blond light brown brown dark brown black ENGLISH 13 white grey red light blond Skin colour and characteristics White always sunburn no tanning 4 5 x Beige easy sunburn minimal tanning 4 5 x Light brown sometimes sunburn good 4 5 x anning id brown rarely sunburn fast and good 2 3 x anning Dark brown rarely sunburn very good x x anning Brownish black and darker rarely to never x x sunburn very dark tanning Important To check whether Philips Lumea Essential is suitable for you see section For whom is Philips Lumea Essential not suitable Tanning advice Avoid sunbathing when you use Philips Lumea Essential regularly every two weeks Sunbathing can cause skin to darken tan or can cause sunburn reddening of the skin Using Philips Lumea Essential on darkened tanned an
6. or never get sunburnt and you tan very darkly your skin colour is brownish black or darker In this case you run a high risk of developing skin reactions such as discolourations strong redness or burns when you use Philips Lumea Essential See also chapter Using the appliance section Possible side effects and skin reactions and consult the Recommended light intensities table in the quick start guide If your natural hair colour in the treatment areas is light blond white grey or red The treatment will not be effective Never use the appliance if you suffer from any of the diseases listed below i e f you have a skin disease such as active skin cancer you have a history of skin cancer or any other localised cancer in the areas to be treated If you have pre cancerous lesions or multiple atypical moles in the areas o be treated If you have a history of collagen disorder including a history of keloid scar formation or a history of poor wound healing If you have a history of vascular disorder such as the presence of varicose veins or vascular ectasia in the areas to be treated If your skin is sensitive to light and easily develops a rash or an allergic reaction f you have infections eczema burns inflammation of hair follicles open lacerations abrasions herpes simplex wounds or lesions and haematomas in the areas to be treated If you have had surgery in the areas to be treated If you
7. Always here to help you Register your product and get support at www philips com welcome 561972 SC1991 Question Contact Philips aan te User manual PHILIPS ENGLISH 6 1661 DS 7661 DS 6 ENGLISH Introduction Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome Light based hair removal is one of the most effective methods to treat unwanted body hair with longer lasting results It is different from current home hair removal methods because it significantly reduces hair regrowth Philips has been investigating this method together with leading dermatologists for over 15 years You can now use this innovative technology comfortably in the privacy of your own home whenever you want This appliance has been specifically designed and optimised for use by women but can be used by men as well Philips Lumea Essential enables treatment of unwanted hair on body areas below the neckline Philips Lumea Essential is designed for use by one person only For more information about Philips Lumea Essential see www philips com lumea Check our homepage regularly for updates Benefits provides the following benefits This appliance Intense Pulsed Light IPL technology for home use Philips Lumea Essential uses a light based technology called Intense Pulsed Light IPL IPL is also use
8. Consumer Care Centre in your country your Philips dealer or a Philips service centre Contact the Consumer Care Centre in your coun Philips dealer or a Philips service centre Clean the body attachment and the light exit wind ry your OW carefully If you are unable to clean the body attachment properly contact the Consumer Care Centre in your country your Philips dealer or a Philips service centre to replace the body attachment If there are hairs on the area to be treated these hairs may get burnt when you use the appliance As a result you notice a strange smell Shave the area to be treated properly before you use the appliance If shaving causes skin irritation trim hairs as short as possible and use the Lumea Essential at a comfortable setting Clean the appliance and the body attachment see chapter Cleaning and maintenance Check the skin hair colour table before each use to ensure you select the right light intensity for each treatment If necessary select a lower light intensity Shave the areas to be treated before you use the appliance If shaving causes skin irritation trim hairs as short as possible and use the Lumea Essential at a comfortable setting If the light exit window is broken do not use the appliance anymore to avoid the risk of skin reactions Contact the Consumer Care Centre in your country your Philips dealer or a Philips service centre Shave the are
9. as to be treated before you use the appliance If shaving causes skin irritation trim hairs as short as possible and use the Lumea Essential at a comfortable setting You must not use the appliance on your face inner labia vagina anus nipples and areolas Men must not use it on their face or scrotum Reduce the light intensity to a level that is comfortable for you See chapter Preparing for use section Light intensity Problem The treated areas become red after the treatment The skin reaction after the treatment lasts longer than usual The hair removal results are not satisfactory Possible cause The light exit window is bro The appliance ken is not suitable for your hair or skin colour Slight redness is harmless and normal and disappears quickly You have used light intensity is too high for You have used light intensity a hat you a hat is too low for you You did not make enough overlaps when you used the appliance You do not use the appliance as often as recommended You respond more slowly to IPL treatment than the average user The appliance is not suitable for your hair or skin colour Solution ENGLISH 23 If the light exit window of the body attachment is broken do not use the appliance with this body attachment any more Go to your dealer or a Philips service centre or contact the Cons
10. ause the IPL treatment to feel uncomfortable or it may lead to other unwanted side effects We advise you to wait until the irritation has disappeared Once the hairs stop growing back which usually happens after 4 5 treatments you no longer have to shave before you use the appliance Light intensity Unlike professional light based appliances Philips Lumea Essential has been developed for consumer use and its light pulses are gentler Therefore you can expect a convenient and effective treatment at a light intensity that you find comfortable Philips Lumea Essential provides five different light intensities Adjust the light intensity to your skin and body hair colour and to a level you find comfortable The recommended light intensities table below helps you to establish the right light intensity Consult the table below to determine which light intensities are appropriate for your skin and body hair colour Tip You can put the table in the quick start guide on your skin and compare it with your skin colour Tip We advise you to store the quick start guide in the pouch for future reference Reduce the light intensity if you experience any pain or discomfort Persons with darker skin run a higher risk of skin irritation because their skin absorbs more light Therefore lower intensities are recommended for persons with darker skin The light pulse can feel warm or hot on the skin but should never be painful Different body
11. ce on the skin The overheat protection has been activated The appliance needs to be reset The body attachment is not placed on the appliance properly Solution No action required To reset the appliance switch off the appliance and then switch it on again If you still cannot adjust the light intensity contact the Consumer Care Centre in your country your Philips dealer or a Philips service centre Place the appliance at a 90 angle onto the skin in such a way that all 4 sides of the integrated safety system touch the skin Then check if the ready to flash light lights up continuously and press the flash button If this does not work place the appliance on a part of your body where it is easy to establish full skin contact for example on your lower arm Then check if the ready to flash light works If the ready to flash light still does not start flashing when you place the appliance on the skin contact the Consumer Care Centre in your country your Philips dealer or a Philips service centre When the overheat protection has been activated the fan still works Do not switch off the appliance and let it cool down for approx 15 minutes before you continue to use it After 5 minutes the appliance switches off automatically Then let it cool down for 10 more minutes If the ready to flash light still does not work when you place the appliance on the skin contact the Consumer Care Cen
12. d in the professional beauty market for hair removal and has been in use for the last fifteen years Philips Lumea un a ential now brings this innovative technology to th e comfort of your home Effective hair regrowth prevention for everyday smoothness This method provides you with long lasting hair regrowth prevention and silky smooth skin Our s just two treatments Op o five treatments A red reatment How fast the Philips Lumea eading derma most sensitive Philips Lumea does not requ ologists for an effective and gentle body areas Essential is equipped with a high pe ire replacement This lamp can gene udies have shown a significant hair reduction after imal results were generally achieved after four uction in hair density is visible from treatment to effect becomes visible and how long the results ast varies from person to person For more information see section How o achieve optimal results in chapter Using the appliance Gentle treatment even on sensitive body areas Essential has been developed in close cooperation with reatment even on the No replacement parts needed no hidden costs rformance lamp which rate over 100 000 flashes and should enable you to continuously maintain results for more than 5 years while saving money on expensive replacement lamps Based on average Usage scenario and recommended treatment regime for one user ENGLISH 7 How Philips
13. d or sunburned skin increases the risk of adverse side effects and skin reactions See chapter Using the appliance section Possible side effects and skin reactions Sun exposure before treatment Wait 2 weeks and perform a skin test Wait at least 2 weeks after sunbathing before you use the appliance Perform a skin test see chapter Using the appliance section First use and skin test on the area to be treated to determine the appropriate light intensity Failure to do so increases the risk of developing skin reactions after treatment with Philips Lumea Essential Sun exposure after treatment Wait 48 hours before sunbathing after treatment with Philips Lumea Essential Wait at least 48 hours after treatment before you expose treated areas o the sun Even after 48 hours make sure that the treated skin shows no adverse reaction to the treatment before you expose it to the sun Cover reated areas when you go out into the sun or use a sunblock SPF 30 in he two weeks after treatment Exposing treated areas to sunlight without protection immediately after treatment increases the risk of adverse side effects and skin reactions See chapter Using the appliance section Possible side effects and skin reactions Tanning with artificial light Follow the instructions in Sun exposure before treatment and Sun exposure after treatment above 14 ENGLISH Tanning with creams If you have
14. e D Intensity light 1 goes on Note The appliance always automatically selects the lowest light intensity setting See section Light intensity in chapter Preparing for use to determine the appropriate light intensity To adjust the light intensity setting press the on off button one or more times until you have reached the required setting The corresponding intensity light lights up ENGLISH 15 Place the appliance at a 90 angle on the skin so that the body attachment is in contact with the skin Tip For easier use stretch the area of skin you want to treat D The ready to flash light on the back of the appliance starts blinking to indicate that the appliance is getting ready to release a flash D When the appliance is ready to release a flash the ready to flash light lights up green continuously Ql Press the flash button to release a flash Note The visible light produced by the appliance is the reflection of the flash on the skin and is harmless to your eyes It is not necessary to wear goggles during use Use the appliance in a well lit room this reduces the perceived brightness of the flash Release the flash button once the appliance has flashed EJ Slide the appliance over the skin to the next area to be treated As long as it feels comfortable not painful increase the setting by one level within the recommended range for your skin type and apply one flash for each setting Do n
15. ght During a treatment hairs on the treated area are usually in different stages of the hair growth cycle To effectively treat all hairs you have to repeat the treatment once every two weeks for the first two months An integrated optical filter ensures that no UV light reaches the skin and ensures that the appliance is safe for the skin 11 Fi 1 1 non A EVO IA I U UU General description Fig 5 Intensity lights 1 5 On off button Ready to flash light Air vents Appliance socket Flash button Openings for electronic contacts Light exit window with integrated UV filter Electronic contacts 1 2 3 4 5 6 7 8 9 10 Body attachment suitable for all body areas below the neck 8 ENGLISH 11 Metallic frame inside the body attachment 12 Integrated safety system 13 Adapter 14 Small plug 15 Pouch Also included cleaning cloth Important Read this user manual carefully before you use the appliance and save it for future reference Danger Water and electricity are a dangerous combination Do not use this appliance in wet surroundings e g near a filled bath a running shower or a filled swimming pool Keep the appliance and the adapter dry If the appliance is broken do not touch any inner part to avoid electric shock Never insert any objects into the appliance Warning To prevent damage This appliance is not intended for use by persons including children
16. h light on the back of the appliance starts blinking again to indicate that it is charging Wait until this light lights up continuously before you continue Tip for SC1992 The SC1992 has a slide and flash feature for a more efficient treatment keep the flash button pressed while you slide the appliance over your skin Do not treat exactly the same area multiple times during one session This does not improve the effectiveness of the treatment but increases the risk of skin reactions To avoid untreated areas make sure the flashes are produced close to each other Note that effective light only comes out of the light exit window However always make sure you do not flash the same area twice E When you have finished the treatment press and hold the on off button for 2 seconds to switch off the appliance Check the light exit window and the body attachment for hairs and dirt and clean the appliance after use see chapter Cleaning and maintenance Tips How to achieve optimal results It is normal that hairs are still visible after the first few treatments see chapter Introduction section Working principle for more information To remove all hairs successfully and prevent the hair follicle from becoming active again the treatments have to be repeated once every two weeks for the first two months Your skin should be smooth and hair free by then Please read section Maintenance phase to find ou
17. have epilepsy with flashlight sensitivity If you have diabetes lupus erythematodes porphyria or congestive heart disease If you have any bleeding disorder If you have a history of immunosuppressive disease including HIV infection or AIDS Never use the appliance if you take any of the medications listed below i e If your skin is currently being treated with or has recently been treated with Alpha Hydroxy Acids AHAs Beta Hydroxy Acids BHAs opical isotretinoin and azelaic acid If you have taken any form of isotretinoin such as Accutane or Roaccutane in the last six months This treatment can make skin more susceptible to tears wounds and irritations If you are on painkillers which reduce the skin s sensitivity to heat If you are taking photosensitising agents or medications check the package insert of your medicine and never use the appliance if it is stated that it can cause photo allergic reactions photo toxic reactions or ifyou have to avoid sun when taking this medicine If you take anticoagulation medications including heavy use of aspirin in a manner that does not allow you to stop using them at least one week prior to each treatment with Lumea If you take immunosuppressive medications ENGLISH 11 Never use the appliance on the following areas On the face On nipples areolas labia minora vagina anus and the inside of the nostrils and ears See chapte
18. iance in the manner described below Preparing treatment areas Shave the areas you intend to treat as long as these areas still show hair regrowth Note Do not use depilatory creams instead of shaving Note If your last depilation method involved removing hairs by the roots e g epilating you can start the treatment right away In this case we advise you to shave in between treatments for optimal results Please note that treatment on unshaved or improperly shaved areas has a number of undesired effects The light exit window and body attachment may become contaminated with stray hairs and dirt A contaminated light exit window and body attachment can reduce the life and efficacy of the appliance Contamination of the light exit window can also cause the treatment to become painful or cause skin reactions like redness and discolouration Hairs on your skin can burn which can result in an unpleasant smell 12 ENGLISH Clean your skin and make sure it is hair free entirely dry and free from oily substances e g residues of deodorants lotions perfumes tanning creams and sunscreens Check the appliance especially the light exit window and body attachment for trapped hair dust and fibres If you see any contamination clean the appliance according to the instructions in chapter Cleaning and maintenance If shaving causes wounds or lesions your skin may be more sensitive to IPL than that of others This may c
19. ight exit window the outside surface of the body attachment the metallic frame inside the body attachment Make sure that the electronic contacts do not get wet Note If water does not clean effectively use a few drops of high percentage alcohol to clean the parts mentioned above Note Make sure you clean the appliance before and after each use and if necessary also during the treatment according to the instructions in this section Storage Switch off the appliance unplug it and let it cool down Clean the appliance before you store it Store the appliance in the pouch supplied at a temperature between 20 C and 70 C Tip We advise you to store the quick start guide in the pouch for future reference 20 ENGLISH Ordering accessories To buy accessories or spare parts visit www shop philips com service or go to your Philips dealer You can also contact the Philips Consumer Care Centre in your country see the worldwide guarantee leaflet for contact details Spare parts The following spare parts are available Body attachment Adapter Cleaning cloth Pouch Environment Do not throw away the appliance with the normal household waste at the end of its life but hand it in at an official collection point for recycling By doing this you help to preserve the environment Guarantee and support If you need information or support please visit www philips com support or read the se
20. ot apply more than one flash on the same spot El When you have finished the treatment press and hold the on off button for 2 seconds to switch off the appliance After the skin test wait for 24 hours and check your skin for any reaction If your skin shows reactions choose the highest setting that did not result in any skin reaction for subsequent use Subsequent use Before every treatment clean the body attachment the light exit window and the metallic frame inside the body attachment For more information see chapter Cleaning and maintenance Start each treatment by selecting the light intensity very carefully based on your skin s sensitivity and on how comfortable treatment feels See section Recommended light intensities to select the right setting for your skin type and hair colour combination Note Your skin may react differently on different days occasions for a number of reasons See section Possible side effects and skin reactions in this chapter for more information 16 ENGLISH Follow steps 2 6 of the previous section Before first use and skin test Note It is normal that the appliance and the body attachment become warm during use Slide the appliance over the skin to the next area to be treated and repeat steps 5 and 6 of section First use and skin test in this chapter After each flash it takes up to 3 5 seconds until the appliance is ready to flash again The ready to flas
21. ou to consult a doctor Wait with the next treatment until the skin has healed completely and make sure you use a lower light intensity Skin discolouration this occurs very rarely Skin discolouration manifests itself as either a darker or lighter patch than the surrounding area This is the result of using a light intensity that is too high for your skin colour After use Do not apply any perfumed In rare instances usually a result of using skin the effects of a pigment change can observed In all cases discoloured areas unt skin has regained its n the effects are even il the discolouration ormal skin colour Skin infection and inflammation This occu caused by using the aj ppliance on wounds shaving on already existing wounds or on area more than once after treatment until any skin redness See chapter Preparing for u inflammations infections tat section Contraindications for more information and if you use the a oo high intensi ast longer than ually reversed ingrown hairs Excessive pain this can occur during or after treatment if used the appliance on unshaved skin if yo intensity that is too high for your skin colour if you flash the same ppliance on open wound ttoos burns etc See chapter Importan has disappeared completely about sun exposure and artificial tanning y on too dark is usually Do not treat has disappeared and
22. our treatment After 5 minutes the appliance switches off automatically ntial nutes before you continu minutes Always return the appliance to a serv han in overheat protection If the Do not switch off the appliance e with ice centre authorised by Philips for examination or repair Repair by unqualified people could cause an extremely hazardous situation for the user Do not use the appliance if any of the situations mentioned in section Contraindications apply to you Electromagnetic fields EMF This Philips appliance complies with all applicable standards and regulationsregarding exposure to electromagnetic fields Contraindications For whom is Philips Lumea Essential NOT suitable Philips Lumea Essential is not designed for everyone If any of the following is true for you then this appliance is not suitable for you to use Do not use the appliance if you are pregnant or breast feeding Philips Lumea Essential has not been tested on pregnant women therefore we advise you not to use the appliance if you are pregnant or breast feeding Hormonal changes could increase the sensitivity of your skin and the risk of injury to the skin 10 ENGLISH Never use the appliance if you have an unsuitable skin and or hair colour i e If you are of skin type V you rarely get sunburnt you tan very well and your skin colour is dark brown or if you are of skin type VI you rarely
23. parate worldwide guarantee leaflet Technical specifications Models SC1992 and SC1991 Rated voltage 100V 240V Rated frequency 50Hz 60Hz Rated input 24W Protection against electric shock Class II El Protection rating IP 30 EN 60529 Operating conditions Temperature 15 to 35 C Relative humidity 30 to 95 Storage conditions Temperature 20 C to 70 C Relative humidity 5 to 95 Spectrum of body attachment gt 500nm ENGLISH 21 Troubleshooting This chapter summarises the most common problems you could encounter with the appliance If you are unable to solve the problem with the information below visit www philips com support for a list of frequently asked questions or contact the Consumer Care Centre in your country Problem The adapter appliance becomes warm during charging have switched on the appliance but cannot increase or decrease the light intensity The ready to flash light does not work when place the appliance on the skin The ready to flash light does not work when place the body attachment on my skin but the cooling fan works The ready to flash light lights up continuously but the appliance does not produce a flash when press the flash button Intensity light 1 continues to blink and cannot change the setting Possible cause This is normal The appliance has to be reset You have not properly placed the applian
24. r Using the appliance section Using the appliance in the bikini area Men must not use it on the scrotum or face Over or near anything artificial like silicone implants pacemakers subcutaneous injection ports insulin dispenser or piercings On moles freckles large veins darker pigmented areas scars or other skin anomalies without consulting your doctor This can result in a burn and a change in skin colour which makes it potentially harder to identify skin related diseases e g skin cancer Onwarts tattoos or permanent make up This can result in a burn and a change in skin colour hypopigmentation or hyperpigmentation On areas where you use long lasting deodorants This can result in skin reactions See chapter Using the appliance section Possible side effects and skin reactions Never use the appliance on sunburnt recently tanned last 2 weeks or fake tanned skin All types of tanning can influence the safety of the treatment This applies to exposure to natural sunlight as well as artificial tanning methods such as tanning lotions tanning appliances etc If you are tanned or are planning to tan see chapter Preparing for use section Tanning advice Note This list is not exhaustive If you are not sure whether you can use the appliance we advise you to consult a doctor Preparing for use For optimal results prepare the areas on which you intend to use the appl
25. t how you can keep these results Maintenance phase To ensure that your skin stays smooth and hair free we advise you to repeat the treatment every four to six weeks The time between treatments may vary based on your individual hair regrowth and also across different body areas If too many hairs grow back between treatments simply shorten the treatment interval again but do not treat any area more often than once every two weeks When you use the appliance more frequently than recommended you do not increase the effectiveness but you do increase the risk of skin reactions ENGLISH 17 Guidelines for treatment Average treatment time Area Underarms Bikini line Entire bikini area One lower leg One full leg Approx treatment time 1 minute per underarm 1 minute per side 4 minutes 8 minutes 14 minutes Note The average treatment times above have been observed during research and tests Individual treatment times may vary from person to person Intended treatment areas The appliance is intended to treat unwanted hairs from the underarms arms stomach bikini area and legs It should not be used on the face Using the appliance on the legs Check the recommended light intensities table in chapter Preparing for use section Light intensity to see which settings are suitable for your legs You can move the appliance up and down or across the leg whichever is more convenient to you In order to main
26. tain full contact with the skin you can also place and hold the appliance on your skin sideways Note Bony areas like shinbone and ankles are more sensitive than other areas of the body When you press the body attachment hard onto these areas the skin can be more susceptible to skin reactions such as skin irritation and redness See section Possible side effects and skin reactions in this chapter Press the body attachment onto the skin just hard enough to make the ready to flash light go on but not harder Using the appliance in the bikini area Check the recommended light intensities table in chapter Preparing for use section Light intensity to see which settings are suitable for your bikini area In principle Philips Lumea Essential is safe and gentle enough for treatment of the entire bikini area e g for Brazilian or Hollywood style Use a lower setting on darker pigmented more sensitive skin in the bikini area Do not use the appliance on inner labia vagina and anus Men who wish to treat their pubic area must not use the appliance on the scrotum Note For hygienic reasons always clean the body attachment before you start treating another body area see chapter Cleaning and maintenance Using the appliance on the underarms Check the recommended light intensities table in chapter Preparing for use section Setting the light intensity to see which settings are suitable for
27. tre in your country your Philips dealer or a Philips service centre To reset the appliance switch off the appliance and switch it on again If the ready to flash light lights up continuously but the appliance still does not produce a flash when you press the flash button contact the Consumer Care Centre in your country your Philips dealer or a Philips service centre Properly place the body attachment on the appliance 22 ENGLISH Problem Possible cause All intensity lights go on alternately The appliance needs to be reset All intensity The appliance is lights are blinking defective simultaneously The appliance The body produces a strange attachment and or smell the filter glass is dirty You have not shaved the area to be treated properly You stored the appliance in a dusty environment The skin feels more sensitive than usual during treatment The light intensity you have chosen is too high You did not shave the areas to be treated The light exit window is broken You did not shave the areas to be treated experience an unacceptable pain sensation when use the appliance You treated an area for which the appliance is not intended You have used a light intensity that is too high for you Solution To reset the appliance switch off the appliance and switch it on again If the intensity lights continue to go on al ernately contact the
28. umer Care Centre to have the body attachment replaced Do not use the appliance if your bod y hair is light blond red grey or white Do not use the appliance either if you have dark skin Consult the body hair and skin colour table in the Quick Start Guide No action required Select a lower light intensity the next time See chapter Preparing for use section Light intensity If the skin reaction lasts longer than 3 days contact your doctor Perform a skin test to determine if you can use a higher light intensity see chapter Using the appli and skin test ance section First use For proper hair removal results you have to make overlaps when you use the appliance See chapter Using the appliance section Subsequent use step 4 To remove all hairs successfully and to prevent the hair root from becoming active again the repeated once every two weeks for reatments may vary based on your and also across different body areas back between treatments simply sho frequently than recommended you d treatments have to be he first two months To ensure that your skin stays smooth we advise you to repeat he treatment every four to six weeks The time between ndividual hair regrowth f too many hairs grow rten the treatment interval again but do not treat any area more often than once every two weeks When you use the appliance more o not increase the
29. used an artificial tanning lotion wait until the artificial tan has fully disappeared before you use Philips Lumea Essential Note For more details on unwanted skin reactions see chapter Using the appliance section Possible side effects and skin reactions Using the appliance Check the recommended light intensities table in chapter Preparing for use section Light intensity to determine which light intensities are most suitable for your skin and body hair colour Shave the area you intend to treat before you use the appliance see chapter Preparing for use section Preparing treatment areas If the treatment becomes painful at any point in time reduce the light intensity setting until the treatment is comfortable again If you notice skin reactions stronger than slight redness stop the treatment immediately and read section Possible side effects and skin reactions in this chapter First use and skin test When you use the appliance for the first time or after recent tanning we advise you to perform a skin test on each area to be treated to check your skin s reaction to the treatment and to get accustomed to light based treatment Choose an area close to the area you intend to treat t Insert the small plug into the appliance and put the adapter in the wall socket Note Make sure the body attachment is placed on the appliance Press the on off button to switch on the applianc
30. your rs very rarely and may be or cuts that resulted from you have u use the appliance at a light m cosmetics to the areas treated immediately Do not use deodorant immediately after treating the underarms Wait se section Tanning advice for information ENGLISH 19 Cleaning and maintenance To ensure optimal results and a long life for the appliance clean the appliance before and after each use and if necessary also during the treatment The appliance loses its effectiveness if you do not clean it properly Never clean the appliance or any of its parts under the tap or in the dishwasher Never use scouring pads abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance Never scratch the light exit window or the metallic frame inside the body attachment Note Stop using the appliance when it is no longer possible to clean the light exit window or the body attachment Switch off the appliance unplug it and let it cool down Note The light exit window becomes hot during use Make sure it has cooled down before you clean it To remove the body attachment grab the projections at the top and bottom and pull gently If necessary clean the outside of the appliance with the soft cleaning cloth supplied with the appliance Moisten the soft cloth supplied with the appliance with a few drops of water and use it to clean the following parts the l
31. your underarms Make sure you remove any deodorant perfume cream or other skin care product from your underarms before treatment 18 ENGLISH Tip To achieve optimal results on your underarms stand in front of a mirror to get a good view of the area to be treated and the ready to flash light Raise your arm and place your hand on the back of your neck to stretch the skin in the underarm area Note The reflected light does not harm your eyes If the scattered light is unpleasant close your eyes when you release a flash Possible side effects and skin reactions Common skin reactions Your skin may show slight redness and or may prickle tingle or feel warm This reaction is absolutely harmless and disappears quickly Askin reaction similar to sunburn may occur on the treated area fora short while If this does not disappear within 3 days we advise you to consult a doctor Dry skin and itching may occur due to shaving or a combination of shaving and light treatment This is harmless and disappears within a few days You can cool the area with an ice pack or a wet facecloth If dryness persists you can apply a non scented moisturiser on the treated area 24 hours after the treatment Rare side effects Burns excessive redness and swelling these reactions occur rarely and are usually the result of using a light intensity that is too high for your skin colour If these reactions do not disappear within 3 days we advise y
Download Pdf Manuals
Related Search