SD200 Series SECURITY DEVICE USER`S MANUAL
Contents
1. application The hardware utility program including instructions for its use is provided AS IS without warranty of any kind Posiflex Inc further disclaims all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose the entire risk arising out of the use or performance of the software and documentation remains with you ABOUT THIS MANUAL This manual is written in an attempt with full strength to assist the user to utilize the security upgrade kit SD200 for the Posiflex touch terminal systems This series of products incorporate 2 delicately designed POS peripherals each can be used as an excellent tool to accommodate the required security specially involved in POS business kiosk and hospitality operation This manual covers the conceptual and operational aspects of these units For technical aspects involving opening of the unit or option implementation it is only available to the authorized distributors The manufacturer of the SD200 series heartily apologizes to the user for reserving the right to change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology The user may always obtain the most up to date information through any of our web sites http www posiflex com or http www posiflex com tw Copyright Posiflex Inc 2004 All rights are strictly reserved No part of this documentation2. each track enable disable AlttNum approach for ASCII codes and Leading Stop code enable disable The function for enabling each track of course comes in effect only when the track is physically available Please find in the mini CD delivered with SD200 or Product Information CD delivered with Posiflex POS system the folder for USBMSR and SetUp this demo program or download the installation program from our web http www posiflex com or http www posiflex com tw
3. POSIFLEX SD200 Series SECURITY DEVICE USER S MANUAL Rev Al l FEATURES Optical Finger Print Sensor in USB interface ISO 7811 Magnetic Stripe Reader in USB full speed HID interface Options for MSR heads covering 1 amp 2 2 amp 3 and all 3 tracks 3 tracks type MSR can read also AAMVA and CA DMV card Total power consumption 300 mA 5V DC There are two models SD200 for touch terminal system and SD210 for TM 4115 monitors FCC NOTICE This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference WARRANTY LIMITS Warranty will terminate automatically when the equipment is opened by any person other than the authorized technicians The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper
4. ed cleaners Never submerge the sensor in liquid Never rub the window with an abrasive material including paper Do not poke the window coating with your fingernail or any hard item such as a pen SAE ea ee b Principle The finger print sensor software never stores fingerprint images The finger print sensor software creates a fingerprint template which is a highly compressed and digitally encoded mathematical representation of fingerprint features This template is created when a user registers a finger and is stored in an encrypted file When the user later touches the fingerprint reader to authenticate a new template is created and compared to the registered template If there is a match the authentication is successful c Finger Print Recognition In order for the sensor to acquire a good image of your finger you must place the pad of your finger but not the tip in the center of the sensor window and apply gentle even pressure Do not roll your finger as usually practiced in the traditional ink and paper fingerprint taking technique Pressing too hard will distort your fingerprint Pressing too lightly will not expose a large enough area of your finger Also make sure to hold your finger on the sensor until you see POSIFLEX the sensor light blink this may take longer for dry fingers Then lift your finger Although you may use any finger with the sensor your index finger of either hand works best If the senso
5. may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without the prior written consent of Mustek Corp the publisher of this documentation an ISO 9001 and ISO 14001 certified manufacturer Other brand and product names are trademarks and registered trademarks and service marks of their respective owners P N 19090900030 1 POSIFLEX ll INSTALLATION 1 HARDWARE INSTALLATION For SD200 series ordered with the host system like Jiva series except Jiva 5800 series before the Jiva 5800G version or TM4115 series it is installed on the system at delivery For separately ordered SD200 series it is delivered separately from the system and needs to be fixed onto the system also not recommended for Jiva 5800 series before the Jiva 5800G version per following instructions before use However before trying to install a SD200 please check first that there is one free USB connector in the I O area of the system reserved for this purpose in the system configuration Should there be any need for application of a USB HUB for this connection a self powered type USB HUB with its own power adaptor is required However For SD210 application with TM4115 Please connect the unit to the extension cable in cable cover area of TM4115 and then connect the extension cable to the USB port of the host system You may find two screw holes on back of the right side of
6. r is capturing your finger image as indicated by the sensor blink and you have tried all the above suggestions you may need to reregister your finger d Sensor Activation There will always be a red light from the sensor to detect the presence of a finger when the sensor is activated Failure to connect to a self powered USB port will cause non operation of the sensor If you activate your terminal s power saving functionality but your third party application does not support this then your fingerprint sensor will enter sleep mode even though your workstation does not If this occurs you will need to disconnect and reconnect the sensor to the USB port Please check with your application developer for compatibility e Cleaning the Sensor Depending on the amount of use the sensor window may need to be cleaned periodically To clean it apply the sticky side B of a piece of adhesive cellophane tape on the window and peel it __ away as in the drawing at right Under heavy usage the window coating on some sensors may turn cloudy from the salt in perspiration In this case gently wipe the window with a cloth not paper dampened with a mild ammonia based glass cleaner 2 MAGNETIC STRIPE READER The MSR in SD200 reads an ISO magnetic stripe card without driver Yet there is a Posiflex USB MSR Manager program provided to control some parameter configuration for this MSR The features controllable in this program covers
7. the main unit of Jiva series or TM4115 series Align the upgrade unit to the right edge of the main terminal Insert and fasten with the two screws with split washers included in your kit as indicated in the picture below Upgrade Unit Screw Holes The Upgrade Kit oe Back of Jiva Series 2 DRIVER INSTALLATION 1 For Finger Print Sensor To include the drivers for this sensor to perform finger print registration or verification authentication in an AP requires the software programmer to purchase and utilize its SDK software developer s kit However Posiflex delivers this optical finger print sensor with its drivers Please find in the mini CD delivered with SD200 or Product Information CD delivered with Posiflex POS system the folder for Posiflex POSIFLEX Optical Finger Print Sensor or download the installation program from our web http www posiflex com or http www posiflex com tw 2 For MSR The magnetic stripe reader in SD200 no matter how many tracks are in the reader head connects to the host through USB port working as a USB KB and therefore requires no driver installation except setting up the USB keyboard to be enabled in system CMOS setup if the OS does not do it automatically Refer to Operation Guide for manipulation over the reader configuration lll OPERATION GUIDE 1 FINGER PRINT SENSOR a Cautions Never pour the glass cleaner directly on the sensor window Never use alcohol bas
Download Pdf Manuals
Related Search