Manual - Test Equipment Depot
Contents
1. Figure 3 1 Draft Shield Installation 2 7 Initial Calibration Power on the balance by pressing On Zero Allow at least one minute for the balance to stabilize before calibrating Press and hold the Print Cal button until CAL is displayed The display flashes while zero reading is taken The display flashes the required span mass Put the indicated calibration mass on the pan and press Yes The display flashes amp When calibration is complete darE is displayed Note Calibration is also available in the Setup menu see section 4 2 1 EN 6 TAJ Carat Gold Balances 3 OPERATION Press Zero to zero the balance and then place objects to be weighed on the pan some weighing Modes and Units of measure may initially be unavailable They can be enabled in the Main menu Unit Lin 3 see section 4 3 1 Weighing Units Press Unit fo advance fo next available weighing Unit 3 2 Weighing Modes To access other weighing modes Press and hold Mode until display shows desired mode To exit weighing modes Press and hold Mode until the prior weighing unit is shown 3 2 1 Parts Count Mode Use the Count mode to count parts of uniform weight To begin Parts Counting press On Zero to fare a container or to set the display to zero Access Count Mode Press and hold Mode until the display shows PC L APu is displayed Establish an Average Piece Weight APW Each time a new type of part is to be cou2. a as i namen ano aoa a oo om aw amo com ono 9 40 200 400 600 500 2000 4000 6000 Weighing Gram Grain Carat Kilogram Ounce Ounce Troy Taels Hong Kong Taels Taiwan Units Modes Taels Singapore Tola Tical Pennyweight Pound Parts Counting Tare Range To Capacity by Subtraction Stabilization lt 3 Time sec Operating 50 104 F 10 40 C Temperature Range Operating 30 90 Humidity Range Pan Size mm 100 dia 137x140 Included with Balance 1 TAJ2001 TAJ4001 TAJ6000 models only 2 TAJ501 TAJ602 TAJ2001 TAJ4001 TAJ6000 models only EN 14 TAJ Carat Gold Balances 6 3 Drawings Figure 6 2 Overall Dimensions Carat Model TAJ Carat Gold Balances EN 15 LIMITED WARRANTY Ohaus products are warranted against defects in materials and workmanship from the date of delivery through the duration of the warranty period During the warranty period Ohaus will repair or at its option replace any component s that proves to be defective at no charge provided that the product is returned freight prepaid to Ohaus This warranty does not apply if the product has been damaged by accident or misuse exposed fo radioactive or corrosive materials has foreign material penetrating to the inside of the product or as a result of service or modification by other than Ohaus In lieu of a properly returned warranty registration card the warranty period shall begin on the date
3. Le 15 mai 2003 Ohaus Corporation Etats Unis d Am rique a t r enregistr e la norme ISO 9001 2000 Befolgung Befolgung zu den folgenden Standards wird durch die entsprechende Markierung auf dem Produkt angezeigt die Niederspannung richtungweisendes 2006 95 EC an Die komplette C Dieses Produkt pa t sich an das EMC richtungweisendes 2004 108 EC und Erkl rung der bereinstimmung ist von Ohaus Corporation vorhanden Entsorgung In bereinstimmung mit den Anforderungen der Europ ischen Richtlinie 2002 96 EG ber Elektro und Elektronik Altgerdte WEEE darf dieses Ger t nicht mit dem Hausm ll entsorgt werden Sinngem ss gilt dies auch f r L nder ausserhalb der EU entsprechend den geltenden nationalen Regelungen Bitte entsorgen Sie dieses Produkt gem ss den rtlichen Bestimmungen in einer getrennten Sammlung f r Elektro und Elektronikgerate Bei allf lligen Fragen wenden Sie sich bitte an die zust ndige Beh rde oder den H ndler bei dem Sie dieses Ger t erworben haben Bei Weitergabe dieses Ger tes z B f r private oder gewerbliche industrielle Weiternutzung ist diese Bestimmung sinngemdss weiterzugeben Vielen Dank f r Ihren Beitrag zum Schutz der Umwelt Registrierung nach ISO 9001 Im Jahr 1994 wurde der Ohaus Corporation USA ein Zertifikat der Registrierung nach ISO 9001 vom Bureau Veritus Quality International BVQI verliehen in dem best tigt wird dass das Ohaus Qualit tsmanagements
4. On May 15 2003 Ohaus Corporation USA was re registered fo the ISO 9001 2000 standard Test Equipment Depot 800 517 8431 99 Washington Street Melrose MA 02176 TestEquipmentDepot com FCC Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant fo Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user iS encouraged fo try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Industry Canada Note This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada Conformidad La conformi
5. menu The last item in the main menu is E n d Press Yes to return to the previous weighing mode 4 2 1 Setup Menu 5 6 t u 7 The Setup menu contains the following sub menus Auto Off R 0FF Auto Off settings Gn BFF Setting I will nce turn the balance off after no activity is detected for 4 minutes Light L She Backlight settings On GFF Ruta selecting Ruta will turn the backlight on when the balance detects any activity Minimum 2 seconds Span Calibration SPAT Uses two weight values Zero and a value at or near the full capacity of the balance Span calibration should be performed if the balance is repositioned or when the room temperature changes significantly Linearity Calibration L Uses three weight values Zero a mid range value and full capacity Generally this calibration is not required unless testing shows that the linearity error exceeds the linearity tolerance in the specification table Accuracy of weights is important to maintain weighing integrity Selecting GFF for these settings will reduce battery consumption EN 10 TAJ Carat Gold Balances 4 2 2 Unit Menu t t Each Weighing Unit may be individually set to In or GFF see Table 4 1 for the symbols associated with each Unit or Mode 4 2 3 Other Menus Additional Menus are available if a serial interface option is installed in the balance These menus are explained within the user manual of each option kit 4 3 Calibratio
6. of shipment to the authorized dealer No other express or implied warranty is given by Ohaus Corporation Ohaus Corporation shall not be liable for any consequential damages As warranty legislation differs from state to state and country to country please contact Ohaus or your local Ohaus dealer for further details Test Equipment Depot 800 517 8431 99 Washington Street Melrose MA 02176 TestEquipmentDepot com
7. Test Equipment 99 Washington Street Depot Melrose MA 02176 Phone 781 665 1400 1 800 517 8431 Toll Free 1 800 517 8431 2 7 OHAUS TAJ Carat Gold Balances Instruction Manual Compliance Compliance to the following standards is indicated by the corresponding mark on the product Voltage Directive 2006 95 EC The complete declaration of Conformity is C This product conforms to the EMC directive 2004 108 EC and the Low available from Ohaus Corporation Disposal In conformance with the European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE this device may not be disposed of in MS domestic waste This also applies to countries outside the EU per their specific requirements Please dispose of this product in accordance with local regulations at the collecting point specified for electrical and electronic equipment If you have any questions please contact the responsible authority or the distributor from which you purchased this device Should this device be passed on to other parties for private or professional use the content of this regulation must also be related Thank you for your contribution to environmental protection ISO 9001 Registration In 1994 Ohaus Corporation USA was awarded a certificate of registration to ISO 9001 by Bureau Veritus Quality International BVQI confirming that the Ohaus quality management system is compliant with the ISO 9001 standard s requirements
8. dad a los estandares siguientes es indicada por la marca correspondiente en el producto ce A Este producto se conforma con el EMC 2004 108 EC directivo y la baja tension 2006 95 EC directivo El declaracion completo de la conformidad esta disponible de Ohaus Corporation Eliminacion de residuos De conformidad con las exigencias de la directiva europea 2002 96 CE sobre residuos de aparatos el ctricos y electr nicos RAEE este equipo no puede eliminarse como basura dom stica Esta prohibici n es asimismo v lida para los pa ses que no pertenecen a la UE cuyas normativas nacionales en vigor as lo reflejan Elimine este producto seg n las disposiciones locales mediante el sistema de recogida selectiva de aparatos el ctricos y electr nicos Si tiene alguna pregunta al respecto dir jase a las autoridades responsables o al distribuidor que le proporcion el equipo Si transfiere este equipo por ejemplo para la continuaci n de su uso con fines privados comerciales o industriales deber transferir con l esta disposici n Muchas gracias por su contribuci n a la conservaci n medioambiental Registro ISO 9001 En 1994 Bureau Veritus Quality International BVQI le otorg a Ohaus Corporation EE UU un certificado de registro ISO 9001 el cual confirma que el sistema administrativo de calidad de Ohaus cumple con los requerimientos del est ndar ISO 9001 En mayo 15 del 2003 Ohaus Corporation EE UU fue registrada
9. n Lock Feature sliding the switch fully to the L lock position prevents calibration of the balance Using a paper or wire seal will physically secure the switch if required Locking the calibration Adhesive paper seal Wire or plastic tie seal Figure 4 1 Locking and Sealing the Calibration Lock Switch 4 4 Weigh Below Feature The Weigh Below Hook is stored inside the battery cover Thread the hook into the access hole at the bottom of the balance Mount the balance onto an appropriate assembly that allows free working space below the hook See Figure 4 2 Note Never allow the balance to rest directly on the hook Weigh Below iv access hole A 6 6 Figure 4 2 Setup for using the Weigh Below Hook Test Equipment Depot 800 517 8431 99 Washington Street Melrose MA 02176 TestEquipmentDepot com TAJ Carat Gold Balances EN 11 9 MAINTENANCE 5 1 Troubleshooting The following table lists common problems and possible causes and remedies If the problem persists contact Ohaus or your authorized dealer TABLE ns 1 TROUBLESHOOTING Cannot turn on e A power to balance e Verify AC adapter connections and voltage e Empty or incorrectly installed e Replace batteries check polarity batteries Poor accuracy e Improper calibration e Perform calibration e Unstable environment e Move balance to suitable location e Transportation Lock is set e Slide the pin to the unlocked posi
10. nted the nominal weight of one piece Average Piece Weight must be established using a small quantity of pieces With Clear APW L APY displayed press No to use the previously saved APW or press Yes fo establish a new APW The display indicates the number of pieces to be used fo establish the new APW If a different sample size is preferred press No until the desired sample size is displayed 5 10 20 50 or 100 Put the specified number of pieces on the pan Press Yes to accept new APW After the new APW is established the number of pieces is shown on the display Test Equipment Depot 800 517 8431 99 Washington Street Melrose MA 02176 TestEquipmentDepot com TAJ Carat Gold Balances EN 7 APW Enhancement Since the weight of each piece may vary slightly APW Enhancement when enabled Ent Enh may be used to increase the accuracy of the count The Average Piece Weight is automatically recalculated if the next stable weight is less than or equal to 2 times the original sample weight Enhancement will then continue provided that each additional weight is less than or equal to the previous weight The display shows FAFuU Enh each time the APW is recalculated Establish new APW Press and hold Unit until PC blinks Count Press Zero button Place the quantity fo be counted on the pan Exit Press and hold Mode uniil the prior weighing unit is shown EN 8 TAJ Carat Gold Balances 4 SETTINGS The Settings all
11. nuevamente al est ndar ISO 9001 2000 Conformite La conformit aux normes suivantes est indiqu e par la marque correspondante sur le produit ce A Ce produit se conforme a l EMC 2004 108 EC directif et la basse tension 2006 95 EC directif La d claration complete de la conformit est fournie par Ohaus Corporation Elimination En conformit avec les exigences de la directive europ enne 2002 96 CE relative aux d chets d quipements lectriques et lectroniques DEEE cet appareil ne doit pas tre limin avec les dechets m nagers Logiquement ceci est aussi Valable pour les pays en dehors de l UE conform ment aux reglementations nationales en vigueur Veuillez liminer cet appareil conformement aux prescriptions locales dans un conteneur separe pour appareils lectriques et lectroniques Pour toute question adressez vous aux autorit s comp tentes ou au revendeur chez qui vous avez achete cet appareil En cas de remise de cet appareil p ex pour une utilisation priv e ou artisanale industrielle cette prescription doit tre transmise en substance Merci pour votre contribution la protection de l environnement Enregistrement ISO 9001 En 1994 le Bureau Veritus Quality International BVQI a octroy la certification d enregistrement ISO 9001 Ohaus Corporation Etats Unis d Am rique confirmant que le syst me de gestion de la qualit Ohaus tait conforme aux conditions normalis es de ISO 9001
12. ows the user to customize the balance 4 1 Menu Structure Table 4 1 illustrates the menu structure TABLE 4 1 MENU End Notes Press Unit Symbol Factor Yes or No Gram g Grain GN 15 432 Carat ct 5 Kilogram kg 0 001 Ounce OZ 35 273e 3 Ounce Troy ozt 32 150e 3 Yes or No SEN m Taelshk thk 26 7 18e 3 Taels sg tsg 26 455e 3 Press Taelstw tiw 26 668e 3 Yes or No Mu I Tola tola 85 7 35e 3 Tical tical 61 239e 3 Press dl GN E Penny dwt 64 301e 3 Yes or No Pound Ib 2 204e 3 ct Modes m Parts Count PC EU Default menu settings are shown t sg Gn GF F Gold models have Q unit TW On as default OFF dwt En Carat models have Cf unit DFF as default tola En OFF Kg and Ib are not available in u y tical Ir lower capacity models See Table 6 1 Yes or No TAJ Carat Gold Balances EN 9 4 2 Menu Navigation Main level menus are identified by decimal points between each letter for example SELF Enter Menu With the balance off press and hold the On bution Continue holding the On button until 5 t u 7 is displayed Each main menu is entered by pressing Yes Advance to the next main menu by pressing No Changing Settings Within each main menu are sub menus Enter each sub menu by pressing Yes Advance to the next sub menu by pressing No To accept the displayed sub menu setting press Yes To advance to the next setting press No Menu Exit The last item in each sub menu is End Press Yes to return to the main
13. razione ISO 9001 da Bureau Veritus Quality International BVQI come conferma che il sistema di gestione della qualit Ohaus risponde alle caratteristiche standard di ISO 9001 Il 15 Maggio 2003 Ohaus Corporation USA stata riregistrata per la normativa ISO 9001 2000 vii TAJ Carat Gold Balances EN 1 1 INTRODUCTION This manual contains installation operation and maintenance instructions for the TAJ Carat and Gold Balances Please read the manual completely before using the balance 1 1 Safety Precautions Please follow these safety precautions e Verify that the Power Adapter input voltage matches the local power supply voltage Use the balance only in dry locations Do not operate the balance in hostile environments Do not drop loads on the pan Do not place the balance upside down on the pan service should be performed only by authorized personnel 1 2 Controls ke set Ml ere of Figure 1 1 Controls TABLE 1 1 CONTROL FUNCTIONS e Primary function Short Press If balance is Off turn On If balance is on perform Zero Tare function e Secondary function Long Press Turn balance Off e Menu function Yes This key is used to accept the currently displayed setting value to serial port if installed calibration as available in Menu EN 2 TAJ Carat Gold Balances Key Name Function e Primary function Short Press of Unit Advances to next available unit Unit e Secondary F
14. tion e Debris touching the pan e Clean any debris next to or under the pan e Draft shield is touching the pan e Check that pan is fully seated check sample or sample height Cannot calibrate e Unstable environment e Move the balance to a suitable location e Incorrect calibration mass e Use correct calibration masses e Transportation Lock is set e Slide the pin to the unlocked position e Calibration Lock switch is set e Slide the switch to the unlocked position Err 1 e Invalid Checksum data e Cycle balance off on e Contact Ohaus or authorized dealer Err 2 e Over load or Under load e Verify pan is installed and or excess load is condition removed from pan e Transportation Lock is set e Slide the pin to the unlocked position e Improper calibration e Perform calibration e Invalid calibration mass e Verify correct calibration mass is being used Err 8 e RS232 buffer is full e Cycle balance Off On e Check RS232 settings in balance and computer when RS232 option is installed e Internal data error e Contact Ohaus or authorized dealer Mi Flashing e Battery power is low e Replace batteries soon e Battery power is too low for e Replace batteries proper operation EN 12 TAJ Carat Gold Balances 5 2 Service Information If the troubleshooting section does not resolve or describe your problem contact your authorized Ohaus service agent 6 TECHNICAL DATA 6 1 Specifications TABLE 6 1 SPECIFICATIONS 0 Le Tas a
15. to the power outlet See Figure 2 3 and the power plug to the back of the balance see Figure 2 4 For use only with UL or CSA Certified or equivalent approved power adapter which is a Class 2 or a Limited Power Source device Figures 2 3 Power Adapter Figure 2 4 Power Plug EN 4 TAJ Carat Gold Balances 2 5 Battery Installation and Use The balance may also be powered by batteries Remove the battery cover and install four alkaline AA LR6 type batteries not included Refer to Figure 2 5 to properly install the batteries Under battery power a battery symbol is shown on the left side of the display The Auto Off setting is useful for conserving battery power see section 4 2 1 Figures 2 5 Battery Installation TAJ Carat Gold Balances EN 5 2 6 Draft Shield Installation Carat models only Lay the dome shaped draft shield over the notched metal ring with the open end facing towards the back of the balance With downward pressure rotate the draft shield allowing the bottom edges to slide under the notches of the metal ring Continue rotating the draft shield until the opening is facing forward See Figure 3 1 ee SI a gt E nn a 2 i h im Th il ki j 1 Bi i N j h he at 4 mm A F i i es y f O i ff Pl f l F N i i j K j k J 4 o i A i ef o
16. unction Long Press of Unit Scrolls Mode through available enabled modes and back to the last No used unit e Menu function No This key is used to reject the displayed setting and advance to next available setting 2 INSTALLATION 2 1 Package Contents e Balance Pan Draft Shield Carat models only Power Adapter Calibration Weight Carat models only Gem Scoop Carat models only Instruction Manual Warranty Card 2 2 Location Use the balance on a firm steady surface Avoid locations with excessive air currents vibrations heat sources or rapid temperature changes Adjust the leveling feet so the bubble is centered within the small circle CORRECT INCORRECT Figure 1 1 Level Adjustment Figure 1 2 Level Bubble Test Equipment Depot 800 517 8431 99 Washington Street Melrose MA 02176 TestEquipmentDepot com TAJ Carat Gold Balances EN 3 2 3 Transportation Lock Calibration Lock amp Pan Installation Before using the balance the Transportation Lock must be released At the bottom of the balance slide the locking pin fo the E position See Figures 2 1 If the balance is to be calibrated by the user ensure that the Calibration Lock is set to E position See Figure 2 2 Install the metal pan over the plastic sub platform gt Figure 2 1 Release Transportation Lock Figure 2 2 Release Calibration Lock 2 4 Connect Power A Power Adapter is used to power the balance Connect the Power Adapter
17. ystem den Anforderungen der Norm ISO 9001 entspricht Am 15 Mai 2003 wurde die Ohaus Corporation USA gem der Norm ISO 9001 2000 neu registriert Vi Test Equipment Depot 800 517 8431 99 Washington Street Melrose MA 02176 TestEquipmentDepot com Conformita La conformita ai seguenti campioni e indicata dal contrassegno corrispondente sul prodotto CE A Questo prodotto conforme al EMC 2004 108 EC direttivo e la bassa tensione 2006 95 EC direttivo La dichiarazione completa di conformit disponibile da Ohaus Corporation Smaltimento In conformit a quanto stabilito dalla Direttiva Europea 2002 96 CE in materia di apparecchi elettrici ed elettronici RAEE questo strumento non pu essere smaltito come i normali rifiuti Tale presupposto resta valido anche per i Paesi al di fuori dei confini della UE conformemente alle norme nazionali in vigore Si prega quindi di smaltire questo prodotto separatamente e in modo specifico secondo le disposizioni locali relative alle apparecchiature elettriche ed elettroniche Per qualsiasi chiarimento rivolgersi agli enti preposti o al rivenditore dell apparecchiatura stessa In caso di cessione dello strumento per es per ulteriore utilizzo privato 0 aziendale industriale si prega di comunicare anche questa disposizione Si ringrazia per il contributo alla tutela dell ambiente Registrazione ISO 9001 Nel 1994 Ohaus Corporation USA ha ricevuto il certificato di regist
Download Pdf Manuals
Related Search