Manual - Goldair
Contents
1. The third device disconnects the appliance permanently in case of overheating by means of a thermal fuse it is non resettable IMPORTANT NEVER COVER THIS HEATER WARNING Do not use this heater with a programmer separate timer remote control system or any other device that switches the heater on automatically CAUTION The heater generates heat during use Proper precautions must be taken to prevent the risk of burns scalds fires or other damage to persons Phone 64 0 9 917 4000 Phone 0800 232 633 info cdb co nz CARE AND CLEANING The heater requires regular cleaning to ensure trouble free operation Unplug the heater from the mains supply before cleaning Ensure that the heater has been allowed to cool down completely before cleaning Use a damp cloth not wet to wipe the exterior of the heater to remove dust and dirt Never use solutions such as benzene thinners or polishing agents Use a vacuum cleaner to remove dust and fluff from around the grills and fins Ensure the heater is dry before plugging back into the mains supply Do not attempt to dismantle the heater There are no user serviceable parts For service or repair contact an authorised electrical service technician PROOF OF PURCHASE To receive warranty retain receipt as proof of purchase SUPPORT AND TECHNICAL ADVICE Goldair New Zealand Monday Friday 8am 5pm Goldair Australia Monday Friday 8am 5pm Phone 61 0 3 92. B Assembly Of Your Oil Column Heater ff if ASSEMBLY OF THE HEATER Carefully turn the Main Body upside down on a non scratching and stable surface Be careful to prevent damage to the paint finish or your floor surfacing Fig 1 Fit the wheel assemblies onto the Main Body by placing the U shaped bolts between the outermost fins on each side of the Main Body see Fig 2 4 Securely fasten the wheel assemblies onto the Main Body by screwing the wing nuts onto the U shaped bolts see Fig 5 IMPORTANT Please fit the wheel assemblies as per the diagram Any other position may affect the stability of the heater WARNING Operate the heater in normal upright position only with wheel assemblies attached to the bottom Any other position could create a hazardous situation Operating Your Oil Column Heater Always choose a safe location for the heater keeping in mind the safety precautions outlined Ensure all packaging has been removed from the unit before use This appliance requires no installation it should be used solely as a portable appliance WARNING Keep all objects at least 1 metre SETTING THE TEMPERATURE from the front sides and rear of the appliance HEAT ONCE SWITCH v JE MODE 7 q OF F C 4 Check that the Heat Control Switch is set to Off position before plugging the heater into the mains supply Press the On Off switch along side the heater to On l
3. Press the power button in the centre of the control panel once to start the heater on High Heat 2 If left at this setting the unit will run continuously on High Heat and will not shut off until the unit is manually turned off Press the power button again to change to Low Heat 2 If left at this setting the unit will run continuously on Low Heat and will not shut off until the unit is manually turned off Press the power button a third time to turn the heater OFF and then press the On Off switch along the side of the heater to Off O For greater economy use the High Heat setting initially and then switch to the Low Heat setting Temperature Icon E WT UNE Press the MODE button until the Temperature Icon blinks Use the and button to set your desired temperature After the desired temperature is set the Temperature Icon will stop blinking and the current room temperature will appear The heat will turn off shortly after the set room temperature is reached and the Temperature display will blink The heater will turn back on when the room temperature drops below the set temperature The temperature display will then stop blinking and will display the current room temperature NOTE The temperature display will not reflect the accurate room temperature until the heater has been operating for at least 20 minutes FAHRENHEIT CELSIUS FUNCTION This heater offers the option to read the temperat
4. have been given instruction concerning the use of the appliance by a person responsible for their safety Do not use this appliance in the immediate surrounds of a bath a shower or a swimming pool or other liquids The appliance must not be immersed in any liquids When the appliance has been unpacked check it for transport damage and ensure all parts have been delivered If parts are missing or the appliance has been damaged contact the Goldair Customer Services Team If your appliance does not work or is not working properly contact the place of purchase or the Goldair Customer Services Team Repair work on the appliance by unqualified persons can cause serious risk to the user There are no user serviceable parts installed in the unit Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards This unit is not supposed to be used in or around locations where foodstuffs works of art or delicate articles of science etc are stored Indoor use only Children should be supervised to ensure that they do not play with the appliance Ensure heater is on a flat stable heat resistant surface It is important that you do not cover this heater Components Of Your Oil Column Heater Main Body x1 TONMMUOowz U shape Bolt x2 Wheel Castor x2 Wing Nut x2 ay Cy Main Body LCD Display Control Panel Handle On Off Switch Cable Storage Wheel Assembly Wheel D
5. regularly by unplugging the appliance and vacuum cleaning the air vents and grills Do not use abrasive cleaning products on this appliance Clean with a damp cloth not wet rinsed in hot soapy water only Always remove plug from the mains supply before cleaning Do not connect the appliance to mains supply until completely assembled and adjusted Switch off and use handles provided when moving Do not operate with cord set coiled up as a heat build up is likely which could be sufficient to become a hazard Do not use an extension cord powerboard or external timer with this unit Do not remove plug from power socket until the appliance has been switched off Do not remove plug from power socket by pulling cord always grip plug TECHNICAL SPECIFICATION Model No Supply Wattage GOC4011 230 240VAC 50Hz 2300 2400W 16 17 18 19 20 21 22 23 24 29 26 27 28 29 Always unplug appliance when not in use Do not locate the heater directly below any power socket during operation Do not twist kink or wrap the cord around the appliance as this may cause the insulation to weaken and split Always ensure that all cord has been removed from any cord storage area and is unrolled before use This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they are supervised or
6. 336 4423 Phone 1300 465 324 info cdbgoldair com au CDB 4 GOLDAIR Two Year Warranty Thank you for purchasing this Goldair product Your product is warranted against faults and manufacture when used in normal domestic use for a period of two years In non domestic use Goldair limits the voluntary warranty to three months Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the warranty period This warranty excludes damage caused by misuse neglect shipping accident incorrect installation or work carried out by anyone other than a qualified electrical service technician PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in relation to the goods or services to which this warranty relates In Australia our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act 1993 Goldair New Zealand Goldair Aus
7. Operating Instructions Oil Column Heater General Care And Safety Guide Thank you for choosing a Goldair Oil Heater This Goldair Heater has been designed and manufactured to high standards of engineering and with proper use and care as described in this leaflet will give you years of useful service Please read these instructions carefully 10 11 12 13 14 15 Use only the voltage specified on the rating label of the appliance Keep all objects at least 1 metre from the front sides and rear of the appliance Do not place appliance close to radiant heat source Do not operate in areas where petrol paint or other flammable liquids are used or stored Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock fire or damage to the appliance Do not sit on the appliance Do not operate this appliance with a damaged cord plug or after the appliance malfunctions or has been dropped or damaged in any manner Return to a qualified electrical person for examination electrical service or repair This appliance is intended for household use only and not for commercial or industrial use Use this appliance only as described in this manual Any other use is not recommended by the manufacturer and may cause fire electrical shock or injury The common cause of overheating is deposits of dust or fluff in the appliance Ensure these deposits are removed
8. ays set your desired temperature prior to setting the Timer so that the heater will turn on at the desired temperature setting Press the MODE button until the Timer icon blinks The hour display will appear The Auto On icon will also appear Use the and button to set the heater start time for between 1 and 24 hours from now This function will activate once the Timer icon stops blinking The heater will automatically turn on when time expires NOTE If the desired temperature was set prior to setting the Timer function the heater will cycle on and off as per the selected desired temperature setting once the heater begins to operate TIMER RESET Press the MODE button until the Continuous Run icon appears When set to Continuous Run mode the auto on auto off settings and the temperature setting will be cancelled In Continuous Run the heater will operate to the thermostat maximum temperature setting WARNING Take care in positioning your heater using the Timer will mean the heater will come on automatically Fire may result if the heater has been placed next to combustible material Operating Your Oil Column Heater SAFETY DEVICE This appliance has three protection devices The first device will automatically turn the appliance off if the appliance is not in the appropriate operating position The second device automatically disconnects amp reconnects the appliance at a pre set temperature
9. tralia CDB Goldair CDB Goldair Australia Pty PO Box 100 707 PO Box 574 N S M C South Morang Auckland Victoria 3752 Phone 64 0 9 917 4000 Phone 61 0 3 9336 4423 Phone 0800 232 633 Phone 1300 GOLDAIR 1300 465 324 www goldair co nz www goldair com au Goldair Two Year Warranty IMPORTANT Please complete and retain this warranty card Name Address Place Of Purchase Date Of Purchase Name Of Product Model Number Attach a copy of the purchase receipt to this warranty card Due to continual design improvements the product illustrated in this User Manual may differ slightly from the actual product
10. ure setting in either Fahrenheit or Celsius F C Temperature Display F C feature functions from only the Power or Set Temperature screens Press F C button to toggle between Fahrenheit and Celsius Operating Your Oil Column Heater SET THE TIMER TO AUTO OFF This function should only be set if you want the heater to automatically shut off after a certain period of time 1 to 24 hours from the time the function is set Timer Icon Auto Off Icon Always set your desired temperature prior to setting the Timer so that the heater will shut off at the desired temperature setting Press the MODE button until the Timer icon blinks The hour display will appear The Auto Off icon will also appear Use the and button to set the heater operation time for between 1 and 24 hours from now This function will activate once the Timer icon stops blinking The heater will automatically turn off when time runs out NOTE If the desired temperature was set prior to setting the Timer function the heater will cycle on and off as per the selected desired temperature setting and will discontinue operation once the programmed Timer setting has been reached SET THE TIMER TO AUTO ON This function provides a delayed start option and should only be set if you want the heater to automatically turn ON after a certain period of time 1 to 24 hours from the time the function is set Timer Icon Auto On Icon Alw
Download Pdf Manuals
Related Search