Camera Network Bullet Camera - Free Security
Contents
1. Quick Start Guide 2 Installation Before you start e Make sure the device in the package is in good condition and all the assembly parts are included e The standard power supply is 12V DC or 24V AC please make sure your power supply matches with your camera e Make sure all the related equipment is power off during the installation Check the specification of the products for the installation environment e Make sure that the wall is strong enough to withstand four times the weight of the camera and the bracket For the camera that supports IR you are required to pay attention to the following precautions to prevent IR reflection e Dustor grease on the dome cover will cause IR reflection Please do not remove the dome cover film until the installation is finished If there is dust or grease on the dome cover clean the dome cover with clean soft cloth and isopropyl alcohol e Make sure that there is no reflective surface too close to the camera lens The IR light from the camera may reflect back into the lens causing reflection The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly 14 Network Bullet Camera Quick Start Guide 2 1 Micro Card Installation This series of camera support micro SD card installation and we take type2. Secure the Camera 2 3 3 Wall Mounting with a Gang Box Before you start For mounting with a gang box you have to purchase a gang box Steps 1 Secure the camera attachment to a gang box with screws 2 Route the cables of the camera 3 Secure the camera to the camera attachment with screws 25 Network Bullet Camera Quick Start Guide Camera Attachment Figure 2 14 Secure the Camera 2 4 View Angle Adjusting 3 axis pan tilt rotation adjusting allows adjustment for optimum camera rotation and placement Please follow the steps below to adjust the view angle We take type II camera as the example to explain the adjusting steps Pan Adjustment Steps 1 Loosen the lock screw 1 2 Adjust the panning position of the camera The adjusting range is from 0 degrees to 360 degrees 3 Tighten the lock screw 1 Tilt Adjustment Steps 1 Loosen the lock screw 2 26 Network Bullet Camera Quick Start Guide 2 Adjust the tilting position of the camera The adjusting range is from O degrees to 90 degrees 3 Tighten the lock screw 2 Rotation Adjustment Steps 1 Loosen the lock screw 3 2 Rotate the rotation position to adjust the azimuth angle of the image The adjusting range is from degrees to 360 degrees 3 Tighten the lock screw 3 Panning Rotation i f N Tilting Figure 2 15 Lens Adjustment 2 5 Zoom and Focus Adjusting
3. the supplied screws Pan Screw Tilt Screw Figure 2 6 Install the Camera 3 Adjust the view angle refer to chapter 2 4 18 Network Bullet Camera Quick Start Guide 4 Adjust the zoom and focus refer to chapter 2 5 5 Optional Install the water proof jacket for network interface s Nore It is recommended to adopt the water proof jacket supplied for the network interface when the camera is installed outdoor 1 If the network cable has been settled down cut off the plug of the network cable first 2 Route the network cable through the following components in sequence fix nut water proof ring and the main body of the water proof jacket as shown in the figure 3 Insert the water proof ring into the main body of the water proof jacket to increase the sealing ability of the components 4 Wire the plug and network cables up 5 Fix the O ring to the network interface of the camera and then connect the network cables 6 Wrap the network interface with the main body of the water proof jacket and then rotate the fix nut clockwise to assemble it to the main body of the water proof jacket Network Interface O ring Plug Water proof Jacket Water proof Ring Fix Nut Network Cable Figure 2 7 Install the Water proof Jacket 19 Network Bullet Camera Quick Start Guide 2 2 2 Pendant Mounting s rea You need to purchase a pendant bracket separately if this mounting method is se
4. 22 Network Bullet Camera Quick Start Guide 3 If you need to route cables through the wall or ceiling cut a cable hole according to the drill template Skip this step if you want to route the cables on the surface of the ceiling 4 Route the cables of the camera 5 Secure the camera to the wall or ceiling with expansion screws Figure 2 12 Secure the Camera 2 3 2 Wall Mounting with a Junction Box Before you start 23 Network Bullet Camera Quick Start Guide For mounting with a junction box you have to purchase a junction box Steps 1 Attach the drill template supplied to the wall where the camera is to be mounted 2 Drill holes in the wall according to the number two holes of the drill template 3 If you need to route cables through the wall or ceiling cut a cable hole according to the drill template Skip this step if you want to route the cables on the surface of the ceiling 4 Secure the junction box to the wall with expansion screws 5 Route the cables of the camera 6 Connect the video output connector to the monitor Connect the power connector to the power supply 7 Adjust the image and focus Please refer to the chapter 2 4 and chapter 2 5 for more detailed information 8 Hook the camera to the junction box with the safety rope 9 Secure the camera to the junction box with screws 24 Network Bullet Camera Quick Start Guide Junction Box Figure 2 13
5. 4 108 EC the RoHS Directive 2011 65 EU Network Bullet Camera Quick Start Guide 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper HEN recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info Industry Canada ICES 003 Compliance This device meets the CAN ICES 3 B NMB 3 B standards requirements Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss The precaution measure is divided into Warnings and Cautions Warnings Serious injury or death may occur if any of the warnings are neglected Cautions Injury or equipment damage may occur if any of the cautions are neglected Network Bullet Camera Quick Start Guide A Warnings Follow these
6. Cautions Follow these safeguards to prevent precautions to prevent serious injury or death potential injury or material damage A Warnings Proper configuration of all passwords and other security settings is the responsibility of the installer and or end user In the use of the product you must be in strict compliance with the electrical safety regulations of the nation and region Please refer to technical specifications for detailed information Input voltage should meet both the SELV Safety Extra Low Voltage and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950 1 standard Please refer to technical specifications for detailed information Do not connect several devices to one power adapter as adapter overload may cause over heating or a fire hazard Please make sure that the plug is firmly connected to the power socket When the product is mounted on wall or ceiling the device shall be firmly fixed Network Bullet Camera Quick Start Guide e If smoke odor or noise rise from the device turn off the power at once and unplug the power cable and then please contact the service center A Cautions e Make sure the power supply voltage is correct before using the camera e Do not drop the camera or subject it to physical shock e Do not touch sensor modules with fingers If cleaning is necessary use clean cloth with a bit of ethanol and wipe it gently If the camera will not be used for an
7. HIKVISION Network Bullet Camera Quick Start Guide UD 6L0201B1867A01 www hikvision com Network Bullet Camera Quick Start Guide Quick Start Guide COPYRIGHT 2015 Hangzhou Hikvision Digital Technology Co Ltd ALL RIGHTS RESERVED Any and all information including among others wordings pictures graphs are the properties of Hangzhou Hikvision Digital Technology Co Ltd or its subsidiaries hereinafter referred to be Hikvision This user manual hereinafter referred to be the Manual cannot be reproduced changed translated or distributed partially or wholly by any means without the prior written permission of Hikvision Unless otherwise stipulated Hikvision does not make any warranties guarantees or representations express or implied regarding to the Manual About this Manual This Manual is applicable to 26xx Network Camera The Manual includes instructions for using and managing the product Pictures charts images and all other information hereinafter are for description and explanation only The information contained in the Manual is subject to change without notice due to firmware updates or other reasons Please find the latest version in the company website http overseas hikvision com en Please use this user manual under the guidance of professionals Trademarks Acknowledgement HIKVISION other Hikvision s trademarks and logos the properties of Hikvision in various
8. LAW HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES Network Bullet Camera Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW THE LATER PREVAILS Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied C accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the EMC Directive 200
9. Purpose You can use the zoom lever and focus lever to adjust the zoom value and focus value Please follow the steps below to adjust the focus 27 Network Bullet Camera Quick Start Guide and zoom We take type II camera as the example to explain the adjusting steps Steps 1 Disassemble the camera 2 View the camera image using the monitor 3 Loosen the zoom lever and move the lever between T Tele and W Wide to obtain the appropriate angle of view 4 Tighten the zoom lever 5 Loosen the focus lever and move the screw between F Far and N Near to obtain the optimum focus 6 Tighten the focus lever 7 Assemble the camera Zoom Focus Lever Figure 2 16 Zoom and Focus Adjustment E NOTE If the camera is equipped with a fixed lens you don t need to adjust the zoom and focus 28 Network Bullet Camera Quick Start Guide 3 Setting the Network Camera over the LAN Note You shall acknowledge that the use of the product with Internet access might be under network security risks For avoidance of any network attacks and information leakage please strengthen your own protection If the product does not work properly please contact with your dealer or the nearest service center 3 1 Wiring Please connect to the camera to the network according to the following figures o or wo Network cable fa Network Camera Computer Figure 3 1 Connecting Directly Network Camera Computer F
10. camera as the example to explain the installation steps Steps 1 Rotate the lock screw counterclockwise to loosen it Slide the sun shield according to the arrow direction as shown below Figure 2 1 Loosen the Lock Screw 2 Remove the sun shield 15 Network Bullet Camera Quick Start Guide Figure 2 2 Remove the Sun Shield 3 Remove the front cover by rotating it counterclockwise 4 Insert the SD card to the SD card slot Figure 2 3 Insert the SD Card 5 Rotate the front cover clockwise back to the camera and install the sun shield back 6 Tighten the lock screw clockwise to tighten the sun shield 16 Network Bullet Camera Quick Start Guide Rotating Figure 2 4 Tighten the Front Cover E NOTE For water proof please align the rotating label on the front cover with that on the camera when you rotate the front cover clockwise 2 2 Type Camera Mounting 2 2 1 Wall Mounting E You need to purchase a wall bracket separately if wall mounting is selected Steps 1 Install the wall bracket to the wall with the supplied screws 17 Network Bullet Camera Quick Start Guide Pedestal Figure 2 5 Install the Wall Bracket Please insert the expansion screws first if the camera is mounted to the cement ceiling And you can use the self tapping screws directly if camera is mounted to the wooden ceiling 2 Align the camera to the pedestal of the bracket and fix the camera with
11. d by the SADP please refer to the User Manual of SADP for details 34 Network Bullet Camera Quick Start Guide 4 Accessing via Web Browser System Requirement Operating System Microsoft Windows XP SP1 and above version CPU 2 0 GHz or higher RAM 1G or higher Display 1024x768 resolution or higher Web Browser Internet Explorer 8 0 and above version Apple Safari 5 0 2 and above version Mozilla Firefox 5 0 and above version and Google Chrome 18 and above version Steps 1 Open the web browser 2 Inthe browser address bar input the IP address of the network camera and press the Enter key to enter the login interface Note The default IP address is 192 168 1 64 If the camera is not activated please activate the camera first according to Chapter 3 2 3 Input the user name and password The admin user should configure the device accounts and user operator permissions properly Delete the unnecessary accounts and user operator permissions Note The device IP address gets locked if the admin user performs 7 failed password attempts 5 attempts for the user operator 35 Network Bullet Camera Quick Start Guide 4 Click Login English UserName admin Password seese Login Figure 4 1 Login Interface 5 Install the plug in before viewing the live video and managing the camera Please follow the installation prompts to install the plug in You may have to close the web bro
12. ecially in the high security system resetting the password monthly or weekly can better protect your product 4 Confirm the password 5 Click OK to save the password and enter the live view interface 31 Network Bullet Camera Quick Start Guide 3 2 2 Activation via SADP Software SADP software is used for detecting the online device activating the camera and resetting the password Get the SADP software from the supplied disk or the official website and install the SADP according to the prompts Follow the steps to activate the camera please refer to the User Manual of Network Camera for other two activation methods Steps 1 Run the SADP software to search the online devices 2 Check the device status from the device list and select the inactive device Figure 3 4 SADP Interface Note The SADP software supports activating the camera in batch Please refer to the user manual of SADP software for details 32 Network Bullet Camera Quick Start Guide 3 Create a password and input the password in the password field and confirm the password STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing using a minimum of 8 characters including upper case letters lower case letters numbers and special characters in order to increase the security of your product And we recommend you reset your password regularly especially in the high security system
13. es according to the instructions provided by the battery manufacturer If the product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the camera yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance Network Bullet Camera Quick Start Guide Table of Contents 1 Appearance Description 10 1 1 Type Camera 1 2 Type II Camera 2 Installation 2 1 Micro Card Installation 2 2 Type Camera Mounting sees 17 2 2 1 Wall Mounting 2 2 2 Pendant Mounting 2 3 Type Il Camera Mounting is 2 3 2 Wall Mounting with a Junction Box 2 3 3 Wall Mounting with a Gang Box 2 4 View Angle Adjusting 2 5 Zoom and Focus Adjusting 27 Setting the Network Camera over the LAN 29 3 1 Wiring 3 2 Activating the Camera 3 2 1 Activation via Web Browser ps 3 2 2 Activation via SADP Software 32 3 3 Modifying the IP Address 33 4 Accessing via Web Browser lt 35 Network Bullet Camera Quick Start Guide 1 Appearance Description 1 1 Type Camera The overv
14. extended period please replace the lens cap to protect the sensor from dirt e Donotaim the camera at the sun or extra bright places Blooming or smearing may occur otherwise which is not a malfunction and affect the endurance of sensor at the same time The sensor may be burned out by a laser beam so when any laser equipment is in using make sure that the surface of sensor will not be exposed to the laser beam e Donot place the camera in extremely hot cold the operating temperature shall be 30 C 60 C or 40 C 60 C if the camera model has an in its suffix dusty or damp locations and do not expose it to high electromagnetic radiation e To avoid heat accumulation good ventilation is required for operating environment e Keep the camera away from liquid while in use Network Bullet Camera Quick Start Guide While in delivery the camera shall be packed in its original packing or packing of the same texture Regular part replacement a few parts e g electrolytic capacitor of the equipment shall be replaced regularly according to their average enduring time The average time varies because of differences between operating environment and using history so regular checking is recommended for all the users Please contact with your dealer for more details Improper use or replacement of the battery may result in hazard of explosion Replace with the same or equivalent type only Dispose of used batteri
15. iew of type camera is shown below SE 1 LS HN Figure 1 1 Overview of Type Camera Table 1 1 Description No Description 1 Sun Shield 2 Front Cover 3 Zoom and Focus Lever 10 Network Bullet Camera Quick Start Guide No Description 4 IR LED 5 Lens 6 Air Vent 7 Video Output Interface 8 Reset Button 9 SD Card Slot 10 Audio Cable 11 Alarm Cable 12 Power Cable 13 Network Cable NOTE Press RESET about 10s when the camera is powering on or rebooting to restore the default settings including the user name password IP address port No etc 1 2 Type Il Camera The overview of the network bullet camera is shown below 11 Network Bullet Camera Quick Start Guide Figure 1 2 Overview of Type Il Camera Table 1 2 Description No Description 1 Sun Shield 2 Front Cover 3 Zoom and Focus Lever 4 IR LED E Lens 6 Air Vent 12 Network Bullet Camera Quick Start Guide No Description 7 Video Output Interface 8 Integrated Bracket 9 Reset Button 10 SD Card Slot 11 Audio Cable 12 Alarm Cable 13 Power Cable 14 Network Cable E vore Press RESET about 10s when the camera is powering on or rebooting to restore the default settings including the user name password IP address port No etc 13 Network Bullet Camera
16. igure 3 2 Connecting via a Switch or a Router 29 Network Bullet Camera Quick Start Guide 3 2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera Activation via Web Browser Activation via SADP and Activation via Client Software are all supported We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation Please refer to the User Manual of Network Camera for Activation via Client Software 3 2 1 Activation via Web Browser Steps 1 Power on the camera and connect the camera to the network 2 Input the IP address into the address bar of the web browser and click Enter to enter the activation interface Notes e The default IP address of the camera is 192 168 1 64 e Forthe camera enables the DHCP by default you need to activate the camera via SADP software and search the IP address 30 Network Bullet Camera Quick Start Guide Figure 3 3 Activation Interface Web 3 Create a password and input the password into the password field STRONG PASSWORD RECOMMENDED We highly A recommend you create a strong password of your own choosing using a minimum of 8 characters including upper case letters lower case letters numbers and special characters in order to increase the security of your product And we recommend you reset your password regularly esp
17. jurisdictions Other trademarks and logos mentioned below are the properties of their respective owners Network Bullet Camera Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THE PRODUCT DESCRIBED WITH ITS HARDWARE SOFTWARE AND FIRMWARE IS PROVIDED AS IS WITH ALL FAULTS AND ERRORS AND HIKVISION MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION MERCHANTABILITY SATISFACTORY QUALITY FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT OF THIRD PARTY IN NO EVENT WILL HIKVISION ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL CONSEQUENTIAL INCIDENTAL OR INDIRECT DAMAGES INCLUDING AMONG OTHERS DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION OR LOSS OF DATA OR DOCUMENTATION IN CONNECTION WITH THE USE OF THIS PRODUCT EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES REGARDING TO THE PRODUCT WITH INTERNET ACCESS THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK HACKER ATTACK VIRUS INSPECTION OR OTHER INTERNET SECURITY RISKS HOWEVER HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED SURVEILLANCE LAWS VARY BY JURISDICTION PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE
18. lected Steps 1 Fix the pendant bracket to the ceiling with the supplied screws Ceiling Figure 2 8 Fix the Pendant Bracket 2 Loosen and remove the set screw on the sun shield of the camera 3 Aim the screwed hole on the camera at the top of the pendant bracket and then rotate the camera until it is secured tightly 20 Network Bullet Camera Quick Start Guide Figure 2 9 Secure the Camera 4 Loosen the knob on the bracket and adjust the camera body to get the desired surveillance view angle Then tighten the knob on bracket to secure the camera Figure 2 10 Adjust the View Angle 21 Network Bullet Camera Quick Start Guide 5 Adjust the view angle refer to chapter 2 4 6 Adjust the zoom and focus refer to chapter 2 5 7 Optional Install the water proof jacket for network interface For details refer to the Step 5 in Chapter 2 2 1 2 3 Type Il Camera Mounting This camera is equipped with a bracket on the bottom It can be mounted to a wall directly and can also be mounted to a wall with a junction box or a gang box 2 3 1 Wall Mounting Steps 1 Attach the drill template supplied to the wall where the camera is to be mounted 2 Drill screw holes in the wall according to the number one holes of the drill template 2 ceiling Mounting 1 e 1 2 Screw Hole fo Screw Hole for Mounting Base Figure 2 11 Drilling Holes in the Wall
19. resetting the password monthly or weekly can better protect your product 4 Click OK to save the password You can check whether the activation is completed on the popup window If activation failed please make sure that the password meets the requirement and try again 3 3 Modifying the IP Address Purpose To view and configure the camera via LAN Local Area Network you need to connect the network camera in the same subnet with your PC Then install the SADP software or client software to search and change the IP of network camera We will take modifying the IP Address via SADP software as an example to introduce the IP address modification Steps 1 Run the SADP software 2 Select an active device 33 Network Bullet Camera Quick Start Guide Note Please refer to Chapter 3 2 to activate the camera if the camera is inactive 3 Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP Modify Network Parameters IP Address Port Subnet Mask IPv4 Gateway IPv6 Address IPv6 Gateway IPv6 Prefix Length HTTP Port Device Serial No Enable DHCP Password 192 168 1 64 8000 255 255 255 0 192 168 1 1 0 80 XX XXXXXXX XXXXXXXX Save Figure 3 5 Modify the IP Address 4 Input the password to activate your IP address modification The batch IP address modification is supporte
20. wser to finish the installation of the plug in 36 Network Bullet Camera Quick Start Guide Live View Playback Log Configuration e click here to download and install the plug in the plug in Figure 4 2 Download Plug in Setup Web Components Click Next to continue or Cancel to exit Setup Cave Figure 4 3 Install Plug in 1 37 Network Bullet Camera Quick Start Guide a Setup Web Components Setup has finished installing Web Components on your computer Click Finish to exit Setup NN Figure 4 4 Install Plug in 2 6 Reopen the web browser after the installation of the plug in and repeat steps 2 4 to login un Nore For detailed instructions of further configuration please refer to the user manual of network camera 38 First Choice for Security Professionals Hikvision All Rights Reserved
Download Pdf Manuals
Related Search