User Manual
Contents
1. is recommended 24 41 dp b Camddns service DONS Setting Enabled Disabled Provider ddns camddns com Username State Hote 1 Schedule Update Feature of DOHS schedule update iz designed for IP products which installed behind the ICS or HAT devices Update range from every 5 minutes to 5000 minutes and 0 remain 10 off 2 Please note that the hostname will be blocked by DynDH5 orqg if schedule update iz more than once every 5 minutes to 60 minutes In general schedule update in every 1440 minutes is recommended Please enable this service Key in user name 1 2 3 IP Schedule update is default at 5 minutes 4 Click Apply DDNS Status I 2 3 Updating Information update Idle Stop service DDNS registration successful can now log by http lt username gt ddns camddns com Register successfully Update Failed the name is already registered The user name has already been used Please change it Update Failed please check your internet connection Network connection failed Update Failed please check the account information you provide The server user name and password may be wrong 25 41 CAMERA dp C Setting LI M Image Setting Privacy Mask Image Setting Brightness Contrast Sharpness m Compensation Hight Mode Video Orientation Fip Mirror For the security purpose there are three areas2. Hetwork 03 07 52 130752f avi Hetwork Diz connected 03 08 22 1908227 Hetwork Diz connected 09 08 51 I30851f auvi Hetwork Dis connected 09 09 21 190921 Hetwork Diz connected 09 09 51 1909517 avi Hetwork Dis connected 2 The video format is AVI Click the video to start Microsoft Media Player to play it 3 To delete the video check it then click Del When the SD card is full it will remove the oldest video automatically 38 41 dp VI Network Configuration i Configuration 1 ADSL Modem Internet 1 Real IF 2 BERGE Internet Access ADSL or Cable Modem IP address One real IP or one dynamic IP Only IP CAMERA connects to the internet For fixed real IP set up the IP into IP CAMERA For dynamic IP start PPPoE ii Configuration 2 oc oUSESE sk t REL o ooo E el z oe Di Ll switch Hub ADSL Modem Internet 1 Real lP 2 PRERE Internet Access ADSL or Cable Modem IP address More than one real IP or one dynamic IP IP CAMERA and PC connect to the internet Device needed Switch Hub For fixed real IP set up the IP into IP CAMERA and PC For dynamic IP start PPPoE Go p m 39 41 iii gt Configuration 3 IP Sharing A ADSL Modem Internet Virtual IP Internet Access ADSL or Cable Modem IP address one real IP or one dynamic IP
3. windows Messenger Internet Options Security Settings Settings C Enable Binary and script behaviors Administrator approved Disable 0 Enable Download signed Activex controls Disable Enable Download unsigned Actives controls Disable Enable pal eR a bk l L 22 4 2 4 w il gt Reset custom settings Internet Options General Security Privacy Content Connections Programs Advanced Select a Web content zone to specify its security settings dama o o e Local intranet Trusted sites Restricted sites Internet This zone contains all Web sites you haven t placed in other zones Security level for this zone Custom Custom settings Ta change the settings click Custam Level use the recommended settings click Default Level Custom Level Default Level Security Settings Settings C Disable Enable Prompt E Download unsigned Activex controls E Disable Enable E Initialize and script Activex controls not marked as safe C Disable Enable 3 Run Actives controls and plug ins Administrator approved z D Lu lli ba Reset custom settings When popup the following dialogue box click Yes Warning A Are vou sure vou want to change the security settings for this zone dp IV
4. IP CAMERA and PC connect to the internet Device needed IP sharing v do p m Use virtual IP set up port forwarding in IP sharing 40 41 dp VII Factory Default To recover the default IP address and password please follow the following steps Remove power and press and hold the button in the back of IP CAMERA Factory Default ii Power on the camera Don t release the button during the system booting v It will take around 30 seconds to boot the camera v Release the button when camera finishes proceed vi Re login the camera using the default IP http 192 168 1 200 and user name admin password admin Vill Package contents i IP CAMERA Network Camera ii Adaptor ii gt Ethernet Cable iv CD title User manual IP installation Utility Appendix SD Card Recommended SanDisk 128M SanDisk 8GB SanDisk 256M SanDisk 16GB SanDisk 512M SanDisk 32GB SanDisk 1G Transcend 4GB SanDisk 2G Transcend 8GB SanDisk 4G Transcend 16GB Transcend 32GB 41 41
5. OS Windows 2000 XP 2003 Microsoft IE 6 0 or above Hardware Suggested Intel Dual Core 1 66G RAM 1024MB Graphic card 128MB Minimum Intel C 2 8G RAM 512MB Graphic card 64MB SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Ill Product Installation A Monitor Setting l Right Click on the desktop Select Properties Arrange Icons By Refresh Save s Scheme Graphics Options Display Modes Mew Properties ii Change color quality to highest 32bit 6 41 Display Properties Themes Desktop Screen Saver Appearance Settings Display Plug and Play Monitor on Intel R 82815G 73V 310GL Express Chipset Family Screen resolution Calor qualit Less J More Highest 32 bit v 1024 by 768 pixels B Hardware Installation and I O Pin Assignment Connect a power adapter and IP Camera to PC or local network XN 12v rer js 3 5mm Phone Jack Audio Input Red Wm 3 5mm Phone Jack Audio Output 3 mm Phone Jack Audio Output Green 1 1 RJ 45 7141 2 Tilt 30 90 3 Rotation 180 Once the users open the case the gimbal adjustment offers the convenience method to install on the wall The pan tilt and rotation are provided in this model The users can adjust the gimbal with Pan 172 degree tilt 30 90 degree and rotation 180 degree respectively Control Instruction I O terminal connector used
6. can be playback remotely 3 Axis IP Dome is an easy to use IP Camera which is designed for security application Il Product Specifications Support Video out 2M CMOS Sensor Power over Ethernet available 3 Axis Gimbal Adjustments IR LED Built in 12M Mechanism IR Cut Filter Available 264 JPEG MPEG4 3GPP only compression SD card backup 2 way audio Support Cell Phone PDA 3GPP SDK for Software Integration Free Bundle 36 ch Recording Software Specifications Image Sensor 1 3 CMOS 2M Pixel Lens Type Vari focal 2 7 9mm Mega Pixel Lens 4 41 IC LE Built in 18 IR LED optional IR Distance 12M Optional 1 in 1 Relay Out T x x Yes Optional DC 12V 470mA 3 Axis Gimbal Pan 172 R Mechanism IR cut Filter Optional D Adjustments Angle Tilt 30 90 Rotation 180 Ethernet 10 100 Base T Network Protocol HTTP TCP IP UDP SMTP FTP PPPoE DHCP DDNS NTP UPnP 3GPP System 1600x1200 1280x1024 1280x960 1280x720 a aka 800x600 640x480 320x240 176x144 Video Adjust Brightness Contrast Sharpness BLC Night Mode Full Screen Yes Rowe NI Yes 3 different areas Mail FTP Save to SD card Relay Yes configurable Password protection Firmware Upgrade HTTP mode can be upgraded remotely 9 41 SD card management Recording Trigger Motion Detection IP check Network break down wire only Schedule Relay Video Format AVI JPEG Web browsing requirement
7. uninterruptible power supplies UPS to ensure 24 hours a day 7 days a week operation Ethernet su e PoE IP Camera PoE Switch Ethernet Cable Ethernet Cable PoE IP Camera 11 41 dp C Vi Vil IP Assignment Use the software IP Installer to assign the IP address of IP CAMERA The software is in the attached software CD IP installer supports two languages a IPlInstallerCht exe Chinese version b IPlnstallerEng exe English version There are 3 kinds of IP configuration a Fixed IP Public IP or Virtual IP b DHCP Dynamic IP c Dial up PPPoE Execute IP Installer For Windows XP SP2 user it may popup the following message box Please click Unblock Windows Security Alert ae To help protect your computer Windows Firewall has blocked some features of this program Do pou want to keep blocking this program Q Name IPInstaller V2 1 Network Device Scan Publisher Unknown Keep Blocking Unblock Ask Me Later Windows Firewall has blocked this program from accepting connections from the Internet a network recognize the program or trust the publisher you can unblock it Wher should unblock a program IP Installer configuration IP Installer Y2 2 Device lists e 1 C Server Name IP Address Static DHCP IP Camera 192 168 001 200 Mane IP Camera IP 192 168 Netmask 255 255 Gateway 192 168 DN
8. 9 41 dp Rate to use CBR 32Kbps 4Mbps the higher the CBR is the better the video quality is VBR 1 10 Compression Rate 3 Video Frame Rate The video refreshing rate per second 4 GOP Size It means Group of Pictures The higher the GOP is the better the quality is 5 Video Format MPEG4 or JPEG 6 RTSP Path RTSP output name f 3GPP Streaming mode JGPP Streaming Setting Q Enabled Disabled Resolution 176 144 FPS 45 Farmat MPEG4 Path lt gt Audio AMR lt gt Audio 3GPP mode suggested setting 176x144 resolution 5FPS MPEG4 format 1 Enable or Disable 3GPP Streaming 2 3GPP 3GPP output name 30 41 CAMERA dp iii gt Audio IP CAMERA supports 2 way audio User can send audio from IP Camera Built in mic to remote PC User can also send audio from remote PC to IP Camera s external speaker a Audio from IP camera built in mic to local PC select Enable to start this function IP Camera to PC Enabled Disabled b Audio from local PC to IP Camera Check chatting in the browsing page 2009 SEP 03 11 51 04 Size 800x592 FPS Chatting Online Visitor 1 Relay Out OFF The Audio will not be smooth when enable SD card recording function simultaneously 31 41 CAMERA dp D Event List IP CAMERA provides multiple event settings i Event Setting Event Setting
9. ALLATION AND I O PIN ASSIGNMENT ccccscccsccescceccesccsccescesccescetccesccseesscesccesensscesceuscs 7 TS E E SM ELI MUS S M S 12 14 A LIVE VIDEO 16 V 18 WEE V RE 19 NET 1 PN RCEX 22 26 cEVENDDBISTA cea ME ME RPM E 32 VI NETWORK CONFIGURATION Henne nennen enhn nnn nnn renun nnus 39 VIL FACTORY 41 Vili PACKAGE CONTENTS 2 2 F M CUI Sea Sa DROP NF D E SUEDE 41 APPENDIX A A 41 V1 1 110103 3 41 dp l Preface 3 Axis IP Dome is a professional CMOS 2 Mega Pixel IP Vandal Dome It has built in web server which enables user to view real time video via IE browser It also supports simultaneously H 264 JPEG MPEG4 3GPP Only video compression with CMOS M Pixel Sensor which provides smooth and high video quality The video can be stored in the SD card and
10. Group Modify admin Administrator a Anonymous User Login Yes Allow anonymous login No Need user name amp password to access this IP camera b Add user Type the user name and password then click Add Set C Click edit or delete to modify the user 20 41 dp z User Setting Microsoft Internet SPEI User Setup Username admin Password Confirm ii gt System update System Update Firmware Upgrade Firmware Version y3 2 11 Hew Firmware Reboot System Factory Default Setting Management Right click the mouse button on Setting Download Save Az a File and then select Save As to zave current system s setting in the Hew Setting File a To update the firmware online click Browse to select the firmware Then click Upgrade to proceed b Reboot system re start the IP camera Factory default delete all the settings in this IP camera d Setting Management User may download the current setting to PC or upgrade from previous saved setting 1 Setting download Right click the mouse button on Setting Download Select Save AS to save current IP CAM setting in PC gt Select saving directory Save 2 Upgrade from previous setting Browse gt search previous setting gt open gt upgrade gt Setting update confirm gt click index html to return to main page 21 41 dp B Network i IP Setting IP Camera support
11. Live Video otart a IE browser type the IP address of the IP camera in the address field It will show the following dialogue box Key in the user name and password The default user name and password are admin and admin Connect to 192 168 1 21 IP Camera User name Passivord Remember mv password When connect to the IP CAMERA The following program interface shows 2009 SEP 08 18 01 02 Size 800x592 i Chatting 7 Online Visitor 1 Relay Out OFF 16 41 dp eee 1 QJ Get into the administration page Video Snapshot 3 Show system time video resolution and video refreshing rate Select video streaming source When streaming 2 setting in Video Setting is closed this function will not display 5 IP Camera supports 2 way audio Click the Chatting check box Then you can use microphone which connects to the PC to talk to server side which is IP Camera side 6 Shows how many people connect to this IP camera 7 Control the relay which is connected to this camera Double click the video it will change to full screen mode Press Esc or double click the video again it will change back to normal mode Right Click the mouse on the video it will show a pop up menu snapshot Record start Mute Full Screen zoom 1 Snapshot Save a JPEG picture 2 Record Start Record the video in the local PC It will ask you where to save the video To stop recording righ
12. Motion Detection a M LE S RA D NET EA aav LL A 1 RR kA koki D Ls Sensitivity 10 High gt 1 rHigh 1 High Area 1 E mait FTP Save to 50 card Area 2 E mait FTP C Save to SD card Area 3 E mait FTP C Save to SD card Log E mait FTP Interval period of time between every two motions detected Record File File Format JPEG Files with Record Time Setting Only with JPEG Compression Format AVI File with Record Time Setting Record Time Setti PEG Files with Record Time Setting Only with JPEG Compression Format Pre Alarm JPEG File Single File with Interval Setting Network IP Check IP Check O Enabled Disabled IP Check Save to 50 card a Motion Detection IP CAMERA allows 3 areas motion detection When motion is triggered it can send the video to some specific mail addresses transmit the video to remote ftp server trigger the relay and save video to local SD card To set up the motion area click Area setting Using mouse to drag and draw the area The same operation for area 2 and 3 b Record File Setting IP CAMERA allows 3 different types of recording file to change its record size 32 41 dp a I a When motion alarm is triggered there are 3 different types of record mode 1 AVI File With Record File Setting 2 Multi JPEG
13. S 1 168 95 DNS 2 168 Porti 00 0 00 20 08 5 Search Device To Change Device Name IP address and Gateway 1 Select the device on the left side 2 Change network parameter on the right side 3 Press Submit button 4 Press Search Device to re search again 5 Double click the device to open it IP Installer will search all IP Cameras connected on Lan The user can click Search Device to search again 12 41 dp CAMERA viii X Click one of the IP Camera listed on the left side The network configuration of this IP camera will show on the right side You may change the name of the IP Camera to your preference eg Office warehouse Change the parameter and click Submit then click OK It will apply the change and reboot the Device Pinstayer Rebooting Please wait Please make sure the subnet of PC IP address and IP CAM IP address are the same The same Subnet IP CAM IP address 192 168 1 200 PC IP address 192 168 1 100 Different Subnets IP CAM IP address 192 168 2 200 PC IP address 192 168 1 100 To Change PC IP address Control Panel gt Network Connections gt Local Area Connection Properties Internet Protocol TCP IP Properties Please make sure your IP Camera and PC have the same Subnet If not please change IP Camera subnet or PC IP subnet accordingly Local Area Connection Properties Internet Protocol TCP IP Properties m
14. With Record File Setting only with JPEG compression format 3 Single JPEG Single File with Interval Setting Record Time Setting Pre Alarm and Post Alarm setups for video start and end time when motion detected I O or other devices got triggered Note Pre Post Alarm record time is base on record time setting and IP Cam built in Ram memory Limited by IP Cam built in Ram Memory When information is too much or video quality set too high it will cause recording frame drop or decrease on post alarm recording time Network Dis connected When the network is down it will save the video to local SD card This function is only enabled in wire connection Network IP check When the connection is down it records the video to SD card Make sure the video recording is continuous To use this function key in the IP address of the PC which has recording software installed Enable the function of Save to SD card then click Apply The interval of two video files on SD card is fixed with 30 seconds Schedule Schedule After complete the schedule setup the camera data will be recorded according to the schedule setup Snapshot After enable the snapshot function user can select the storage position of snapshot file the interval time of snapshot and the reserved file name of snapshot 33 41 Schedule NNEMEKNEENNENENNENE Wrth schedule setup Snapshot Enabled Disabled Sn
15. apshot C E mail Save to 50 card Interval 10 Second s 1 50000 File Hame Snapshot ii I O Setting IP CAMERA supports 1 input 1 output When alarm input is triggered there are four related actions can be selected which is sending the E mail to the setup email address transmitting the video to remote ftp server activating the related action in output and saving the video to local SD card lO Setting Input Setting Input 1 Sensor v Input 1 Action E mail FTP Save to SD card Subject GPIO In Detected Interval 10sec Based on the schedule Output Setting Mode Setting 9 onoff Switch Time Switch Interval 34 41 dp CATUTION Please connect to propriety relay output device to reduce the risk of electric shock amp damaged Alarm Input Setting Among alarm input setting the user can setup the connected device which can send the signal to relay output when the device is triggered Sensor ALARM 1 Non Triggered Device 3 Mw O bond 3V Tasers Sensor Device Relay Output Setting In relay output setting the user can setup the output device to perform the related output action 35 41 Contact Rating 30V DC 1A 125V AC 0 3A Depends on the devices the user should connect N C and COM pins or N O and COM pins RELAY INSTALLATION EXAMPLE 1 Trigger a normal off Normal Open alarm siren on when event mot
16. can be setup for privacy mask Click Area button first and pull a area on the above image Finally click button to reserve the setting Adjust Brightness Contrast Hue Saturation to get clear video Adjust Brightness Contrast Hue Saturation to get clear video Moreover IP CAMERA supports Back Light Compensation Night Mode and Video Orientation Video Setting User may select 2 streaming output simultaneously otreaming 1 Setting Basic mode and Advanced mode otreaming 2 Setting Basic mode Advanced mode and 3GPP mode Max Video Frame Rate for both streaming combined is 30 FPS 26 41 dp a Video Setting click the drop down list to select the following items Video Setting Input Resolution 1280x720 z 30fps Video System TV Output Auto Auto Based on the Video System 1 Input Resolution There are 1600x1200 0195fps 1280x1024 22fps 1280x960 25fps 1280x720 30fps 800x600 30fps 5 sort of resolution can be selected Different input resolution will have different streaming resolution 2 Video System There are NISC and PAL video system can be adjusted 3 TV Output there are Auto NTSC and PAL 3 options can be changed Under the Auto option it will be based on the selected option in Video System b Streaming 1 Basic Mode Streaming 1 Setting Basic O Advanced Mode Resolution 800 600 Quality Best Video F
17. deem User Manual CMOS 2 0 Mega Pixel 3 AXIS IP Vandal Dome Camera 1 41 dp eee WARINGS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL COPYRIGHT THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED TO THEIR RESPECTIVE COMPANIES 2 41 dp Content l 4 Il PRODUCT 1 4 Ill PRODUCT 6 A MONITOR SETTING cccceccesccsccsccsccecceccscescesccsccsccescscescescesccsccsccscescescesccsscescescescescesccsecssctscescescescesseescens 6 B HARDWARE INST
18. e m General Authentication Advanced General Connect using fou can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for 88 Realtek RTL8133 Family PCI Fast Ethernet NIC the appropriate IP settings C Obtain an IP address automaticall This connection uses the following items Use the following IP address ivi IE Client for Microsoft Networks IP address ivi m File and Printer Sharing for Microsoft Networks JE 005 Packet Scheduler Subnet mask Internet Protocol TCPAP Default gateway Description Use the following DNS server addresses Transmission Control Protocol Internet Protocol The default FRITS server 192 Wr 32 wide area network protocol that provides communication across diverse interconnected networks Aun DHS Seu 168 95 192 1 C Show icon in notification area when connected A quick way to access remote monitoring is to left click the mouse twice on a selected IP Camera listed on Device list of IP Installer An IE browser will be opened 13 41 IP Installer Y2 2 Device lists Server Name IP Address IP Camera 192 168 001 165 Name IP Netmask Gateway DNS 1 95 DNS 2 95 192 1 Porti 80 00 0F 0D 00 21 0F Search Device To Change Device Name IP address and Gateway 1 Select the device on the left side 2 Change network parameter on t
19. econd NTSC Max 30 frames second PAL Max 25 frames second GOP Size It means Group of Pictures The higher the GOP is the better the quality is Video Format H 264 or JPEG RTSP Path RTSP output connecting route 28 41 Streaming 2 Setting Basic Resolution Quality Video Frame Rate Video Format Streaming 2 Basic Mode Q Advanced Mode 640 480 Standard v 15 FPS JPEG RTSP Path Audio G 711 Resolution There are 8 resolutions can be chosen 1600x 1200 1280x1024 1280x960 1280x720 800x600 640x480 320x240 176x144 Quality There are 5 levels to adjust Best High Standard Medium Low The higher the quality is the bigger the file size is Also not good for internet transmitting Video Frame Rate The video refreshing rate per second Video Format H 264 or JPEG RTSP Path RTSP output connecting route aming 2 Advanced Mode 9 Stre Streaming 2 Setting Advanced Mode Y CBR Q Basic Mode Resolution VBR Bitrate Control Mode Video Quantitative Video Bitrate 1 5Mbps Video Frame Rate 15 FPS GOP Size Video Format 264 RTSP Path exmtspuw2 Audio G 711 1 Resolution There are 8 resolutions can be chosen 1600x 1200 1280x1024 1280x960 1280x720 800x600 640x480 320x240 176x144 2 Bitrate Control Mode There are CBR Constant Bit Rate and VBR Variable Bit 2
20. he right side 3 Press Submit button 4 Press Search Device to re search again 5 Double click the device to open it xi Then please key in the default user name admin and password admin Connect to 192 168 1 217 A Camera User name admin Password Remember my password D Install ActiveX control For the first time to view the camera video via IE it will ask you to install the ActiveX component IP CAMERA Microsoft Internet Explorer File Edit View Favorites Tools Help 5 ix E 5 jo 5 Favorites B m 28 A E EE Address htEp 192 158 1 217 i This site might require the following Actives control Hunt Verisign Control From Hunt Electronic Co Ltd Click here to install If the installation failed please check the security setting for the IE browser l IE gt Tools gt Internet Options gt Security Tab gt Custom Level gt Security Settings gt Download unsigned ActiveX controls gt Select Enable or Prompt li IE gt Tools gt Internet Options gt Security Tab gt Custom Level gt Initialize and script ActiveX controls not marked as safe gt Select Enable or Prompt 14 41 IP CAMERA Microsoft Internet Explorer File Edit View Favorites BEES n a aua Address 192 168 1 21 Mail and News Pop up Blocker Manage Add ons Synchronize windows Update
21. ice icon will be added to MY Network Places 6 User may double click the IP device icon to access IE browser PPPoE PPPoE Setting Enabled Disabled Username Password Send mail after dialed Enabled Subject PPPoE From IPcam Select Enabled to use PPPoE Key in Username and password for the ADSL connection Send mail after dialed When connect to the internet it will send a mail to a specific mail account For the mail setting please refer to Mail and FTP settings i DDNS It supports DDNS Dynamic DNS service DynDNS 23 41 Poa CAMERA dp DONS Setting Enabled 9 Disabled Provider Hostname Username Password Schedule Update 1440 Minutes State Idle Hote 1 Schedule Update Feature of DONS schedule update is designed for IP products which installed behind the ICS or HAT devices Update range from every 5 minutes to 5000 minutes and 0 remain to off 2 Please note that the hostname will be blocked by DynDHS orqg if schedule update is more than once every 5 minutes to 60 minutes In general schedule update in every 1440 minutes is recommended Enable this service Key in the DynDNS server name user name and password oet up the IP Schedule update refreshing rate Click Apply If setting up IP schedule update too frequently the IP may be blocked In general schedule update every day 1440 minutes
22. in application for e g motion detection event triggering alarm notifications It provides the interface to 1 Digital Input GND Alarm An alarm input for connecting devices that can toggle between an open and closed circuit for example PIRs door window contacts glass break detectors etc When a signal 1s received the state changes and the input becomes active Relay output COM COM N C An output to Relay switch for example LEDs Sirens etc Digital Input Alarm Input 1 GND Ground Initial state is LOW 2 Alarm Max 50mA DC 3 3V 8 41 dp eee Relay Output 1 N C Normally Close Max 1A 24VDC or 0 5A 125VAC 2 COM Common 3 N O Normally Open Max 24VDC 0 5 125 O Tab SS ALARM Ex Fx NO X V Relay 1 Digital Input connection ALARM IN COM RELAY OUT Door Window Contacts 9 41 dp 2 Relay Output Connection 10 41 dp eee V PoE Power Over Ethernet Optional 802 3af 15 4W PoE Switch is recommended Power over Ethernet PoE is a technology that integrates power into a standard LAN infrastructure It enables power to be provided to the network device such as an IP phone or a network camera using the same cable as that used for network connection It eliminates the need for power outlets at the camera locations and enables easier application of
23. ion occur at COM NC COM NO RELAY INSTALLATION EXAMPLE 2 Trigger the normal on Normal Close indoor illumination off when event motion occur at COM NC COM NO n O ud Fran 36 41 CAMERA dp IV VI Mail amp FTP To send out the video via mail of ftp please set up the configuration first Mail Setting Mail Server Username Password Sender s Mail Recewer s Mail Bec Mail FIP Setting FIP Server Username Password Log List System Logs Motion Detection Logs VO Logs All Logs Logs sort by System Logs Motion Detection Logs and I O Logs In addition System Logs and l O Logs won t lose data due to power failure SD card dp eee Please Insert SD card before use it Make sure pushing SD card into the slot completely Note The use of the SD card will affect the operation of the IP CAMERA slightly such as affecting the frame rate of the video Playback Playback 19700104 20060417 SD Card lt lt 878M 982M gt gt 1 Itwill show the capacity of the SD card Click the date listed on this page It will show the list of the video Time Event Type 09 05 22 3052 Hetwork Dis connected 09 05 52 19055 7f aui Hetwork Dis connected 09 06 22 1906 Hetwork Dis connected 09 06 52 I30652f auvi Hetwork Diz connected 09 07 22 9072
24. rame Hate 15 FPS Video Format H 264 gt RTSP Path Audio G 711 1 Resolution There are 8 resolutions can be chosen 1600x 1200 1280x1024 1280x960 1280x720 800x600 640x480 320x240 176x144 2 Quality There are 5 levels to adjust Best High Standard Medium Low The higher the quality is the bigger the file size is Also not good for internet transmitting 3 Video Frame Rate The video refreshing rate per second Video Format H 264 or JPEG 5 RTSP Path RTSP output name 27141 dp e otreaming 1 Advanced Mode Streaming 1 Setting Resolution 800 600 Bitrate Control Mode VBR Video Quantitative Video Bitrate Video Frame Rate GOP Size GOP 15 Video Format RTSP Path lt gt Audio G 711 Resolution There are 8 resolutions can be chosen 1600x 1200 1280x1024 1280x960 1280x720 800x600 640x480 320x240 176x144 Bitrate Control Mode There CBR Constant Bit Rate VBR Variable Bit Rate to use CBR 32Kbps 4Mbps the higher the CBR is the better the video quality is VBR 1 Low 10 High Compression rate the higher the compression rate the lower the picture quality is vise versa The balance between VBR and network bandwidth will affect picture quality Please carefully select the VBR rate to avoid picture breaking up or lagging Video Frame Rate The video refreshing rate per s
25. s DHCP and static IP IP Assignment DHCP 9 Static IP Address subnet Mask Gateway DHS 0 DHS 1 Port Assignment Web Page Port RTSP Port RTP Start Fort RTP End port UPnP UPnP 192 168 1 200 192 158 1 254 168 95 1 1 168 95 192 1 1024 10000 1025 10000 Enabled Disabled a DHCP Using DHCP IP Camera will get all the network parameters automatically b Static IP Please type in IP address subnet mask gateway and DNS manually Port Assignment user may need to assign different port to avoid conflict when setting up IP assignment 1 Web Page Port setup web page connecting port and video transmitting port Default 80 2 RTSP Port setup port for RTSP transmitting Default 554 3 Start and End Port in RTSP mode you may use TCP and UDP for connecting TCP connection uses RTSP Port 554 UDP connection uses RTP Start and End Port 22 41 IP znamena a I a UPnP This IP camera supports UPnP If this service is enabled on your computer the camera will automatically be detected and a new icon will be added to My Network Places Note UPnP must be enabled on your computer Please follow the procedure to activate UPnP 1 open the Control Panel from the Start Menu 2 select Add Remove Programs 3 Select Add Remove Windows Components and open Networking Services section 4 Click Details and select UPnP to setup the service 5 The IP dev
26. s is the Camera name This name will show on the IP Installer 2 Select language There are English Traditional Chinese and Simplified Chinese to select When change it will show the following dialogue box for the confirmation of changing language Microsoft Internet Explorer EJ y Change Language Are vou sure b OSD Setting Select a position where date amp time stamp text showing on screen OSD Setting Time Stamp Enabled Disabled Text Enabled Disabled Tes m Moreover click Text Edit can entry to adjust the OSD contents which is including Size and Alpha of text Finally click Upgrade button to reserve the setting Text Edit Text Edit Text 42 v Alpha 10095 C Server time setting Select options to set up time NTP Synchronize with PC s time Manual The date and time remain the same 19 41 dp Time Setting Server Time 20077141 14 56 01 Time Zone GMT 08 00 Date Format yyimrm dd O mmddyy O ddimrnayy Time zone GMT 08 00 v 9 HTP Server Q Synchronize Date Time O Manual Date Time GMIT 03 00 O The date 03 30 GMT 04 30 ii User Management IP CAMERA supports three different users administrator general user and anonymous user User Management Anonymnus User Login Oves Add User Username Password Confirm User List Userame User
27. t click the mouse again Select Record Stop The video format is AVI Use Microsoft Media Player to play the recorded file 3 Mute Turn of the audio Click again to turn on it Full Screen Full screen mode 5 ZOOM Enable zoom in and zoom out functions Select Enable digital zoom option first within the pop up dialogue box and then drag and drop the bar to adjust the zoom factors Enable digital zoom Zoom Factors 113 17 41 dp V Configuration to get into the administration page Click to go back to the live Server Information MAC Address Server IP Camera Status Bar Language 9 English O mun O Polski France OSD Setting Time Stamp OO Enabled Disabled Text OO Enabled Disabled est Text Edit Time Setting Server Time 2009 9 3 10 57 44 Time Zone GMT 08 00 Date Forrnat yyimmidd mmddyy ddimmiyy Time Zone GMT 08 00 O Server 198 123 30 132 Update 6 V Hour Time Shift 0 Minutes 1440 1440 Setting O Synchronize with PC s time Date 2009 9 3 1 1 Time 10 57 49 Manual Date 2009 9 3 Time 10 44 13 The date and time remain the same 18 41 CAMERA dp A System i System Information a Server Information Set up the camera name select language and set up the camera time 1 Server Name Thi
Download Pdf Manuals
Related Search