PiXORD H.264 Series 2-Megapixel Network Camera PL621 / PL621E
Contents
1. 40 I O Terminal Connector Pin 51 40 Restore Factory niae oot redo 40 Notices This user manual is intended for administrators and users of the PIXORD Network Camera including instructions for using and managing the camera on your network The use of surveillance devices may be prohibited by law in your country It is the user s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use Before the Network Camera is installed all the safety and operating instructions should be carefully read and followed to avoid damage due to faulty assembly and installation This also ensures the product is used properly as intended Heed all warnings gt Do not drop or strike this equipment Sensitive electronics inside the camera are vulnerable to excessive strike Donotinstall the equipment near any flames or heat sources Excessive heat could damage this equipment gt gt cover cloth or to install this equipment in poorly ventilated places Overheating could damage this equipment gt expose this equipment to rain or moisture Do not touch the power connection with wet hands Risk of short circuit electric shock or fire gt gt damage the power cord or leave it under pressure Risk2. Q Mone Default Q External Q Own Select image file ta upload Upload 39 FAQ Terminal Connector Pin Assignment B Video output LL e 3 T Microphone input FSD Audio output GREED Network 5 6 Load default Restore Factory Default To restore factory default please follow the steps 1 Unplug the power jack to turn off the camera 2 Short pin 5 and pin 6 with a wire 3 Plug in the power jack to turn on the camera The power LED will start flashing in a short while 4 Break the short when the LED starts quick flashing Wait for a few minutes the device should be set back to factory default 40
3. DDNS Status Date amp Time Event Schedule Network System Customize Server Maintenance Log Service PIZORD 2009 09 08 10 48 05 1 0 2 rc7 4391 00 04 29 01 05 ff 1 0 1 131 Connected DHCP 192 168 6 85 255 255 255 0 192 168 6 254 192 168 0 13 192 168 0 16 Refresh 33 User Login users for Web access and operations authentication required The Check box is for anonymous logging on to the live view page Logging for further configurations will still require user name and password Follow the conditions shown to add different users with different authority Live View ideo Camera Event Schedule Network System Customize Information User Date amp Time Server Maintenance Log Service User Setting Enable anonymous lagin no user name or password required User List User Hame User Group Administrator Add Remove 34 Date amp Time System date time configuration Options of synchronizing with PC and NTP server are provided for automatic adjustment Live View ideo Camera Event Schedule Network System Customize E Information User Date amp Time Server Maintenance Current Server Time Log Service Date Time Set Server Time Automatically adjust for daylight saving time changes Time Mode Q Synchronize with camputer time Date Time Synchronize with NTP server Time zone Set Manually Date
4. l Image Format 264 Resolutian 540 x 460 GOP 3n 1 150 Video Made Frame Rates 30 530 FPS Quality Level Standard Stream 3 Setting RTSP Path 02 Image Format H 264 Resolution 320x240 30 Wideo WER Frame Rates 30 820 FPS Quality Level Standard Save Stream 1 Setting gt gt gt RTSP Path It is the stream ID used for RTSP client streaming connection such as VLC player Resolution Choose image size from 320x240 to 1600x1200 Video Mode Choose between variable bit rate VBR and constant bit rate CBR VBR gt Choose quality level from best to standard CBR gt Choose target bit rate range from 64 to 6000kb Image Format 2 kinds of format to choose from MJPEG and H 264 GOP Group of pictures Frame Rates FPS Choose the number of frames to display per second With resolution 1600x1200 FPS can only set up to 15FPS The rest can set up to 30FPS Stream 2 Setting Configuration of stream 2 is the same as stream 1 Note Resolution can only be set to 320x240 or 640x480 Stream 3 Setting Only RTSP path image format and frame rate can be adjusted the rest of the settings are fixed 15 3 Camera General e Live View ideo Camera Event Schedule Network System Customize 1 General Advanced Camera General Setting o Bp SS 8S 31i Hee p 9 1 uni p i Rotation 180 Audio Setting v A
5. Snapshot the image Rotate image 90 degrees clockwise 12 Configuration Pages List Video gt General Advance gt External Video Source Camera gt General gt Advance Event gt Event Server gt Motion Detection gt Ports gt Event Configuration ochedule gt General gt Storage Network gt General Advance gt SMTP E mail gt DDNS System gt Information gt User gt Date amp Time gt Server Maintenance gt Log Service Customize gt Style Layout 13 2 Video General Live View Video Camera Event Schedule Network System Customize General Advanced Video General Setting Enable Stream 1 v Enable Stream 2 Enabled Digital PTZ Enable Strearn 3 OSD Setting Enable Camera Mame 20 character max Date Time Save Video General Setting Check each box to enable streams max 3 for live viewing Note Digital PTZ is only available with stream 2 OSD Setting Enable OSD to display camera name and date time on the image 14 Advanced Live View viden Lamera Event Schedule Network System Customize NN General Advanced External Video Source Stream 1 Setting RTSP Path Image Format H 264 Resolution 640 x 480 bul 30 1 150 Video Made Frame Rates 30 530 FPS Target Bit Rates 2000 64 6000 Kb Stream 2 Setting RTSP Path
6. 2009 09 07 Time 02 38 42 ex 2008 01 011 ex 01 00 00 35 Server Maintenance This page provides tool for system maintenance Reboot and Load default settings as well as functionalities of launching upgrade process backup restore user settings and language defines Live View ideo Camera Event Schedule Network System Customize Information User Date amp Time Server Maintenance Log Service Maintain Server Reboot Load default Firmware Upgrade Model Firmware Version 1 0 2 rc7 4391 Address 00 04 29 01 9e ff Actives 1 0 1 131 Specify the firmware to upgrade Upgrade Backup Save all parameters and user defined scripts to a backup file Backup Upload Setting Use a saved backup file to return the unit to a previous configuration Specify the backup file ta use Upload Add Language Get a language file fram lang lang js Select language file to upload Upload Language 36 Log Service Most system operations and or process will be kept in a log system The link provides the review of these records Live View ideo Camera Event Schedule Network System Customize Information User Date amp Time Server Maintenance Log Service Reports Server Report Parameter List 37 7 Customize This page provides the function of adjusting the look of live view page There are two types of layout settings use default lo
7. gt Open Web on the menu bar If the device has been configured correctly the default Web browser will open to the home page of the selected device If you find your browser is opened and automatically connected to the camera Home Page it means you ve assigned an IP Address to the unit successfully Now you can close the IP Installer and start to use your camera Verify and Complete the Installation from Your Browser When browsing the Home Page at the first time with the Microsoft Internet Explorer you must temporarily lower your security settings to perform a one time only installation of the ActiveX component onto your workstation as described below 1 2 3 4 5 From the Tools menu select Internet Options Click the Security tab and then click Custom Level button to see your current security settings Set the security level to Low and click OK Type the URL or IP address of your camera into the Address field A dialog box will pop up asking if the ActiveX control should be installed Click Yes to start the installation Once the ActiveX installation is complete return the security settings to their original value as noted above Using the Web UI otart your Web browser and enter the URL or IP address in the Address field The Home page of the camera is now displayed Edit gt Favorites Tools Help EE a O Xr O S S L
8. YI Address 192 168 2 87 __ HN MM ivl ws e windows Live What s New Profile Photos Calendar Share Sign in PIXORD IP 192 168 2 7 H264 640X480 15 FPS 932 K bps 2009 09 22 oe lt a 009 07715 15 3473586 72 4 Done Internet 10 1 Live View Video format Bit rate 4 5 Cha IP address of the camera ET fm co NO s mimi ahan oe Resolution Frame Rate GR Nimes So LEA n 1 EL PiXORD 92 10 1102 FPS 1976 bg y 1 D xi Pa k truy Errep E ___ TE Button Description Click for more general advance camera settings LANGUAGE Select languages among English traditional Chinese and simplify English Chinese IMAGE SETUP TEE Check actual size to view the actual size resolution of the image Actual Size MANUAL TRIGGER Click to trigger the alarm manually VIDEO STREAM Sie EE Choose among the 3 streams for viewin PIN DE E 9 9 11 PiXORD ICT TET FPS OP Kbps a oy ej a i Listen the audio input from local end Talk function om Record instant live video
9. Enabled Stream 2 1 Slice File Size Save Device Local Disk E n ni EH E Scheduled 26 otorage Display the storage information includes disk size info type and status The warning message shows when recording is on process SD card should not be removed during the recording process Live View Video Camera Event Schedule Network System Lustomize General Storage Disk Status Model Hama fdevufmrmeblkop1 Total Size 1929024 Used Size 1788864 KB Free 5122 140160 Disk 50 Disk Status recording _ Refresh Browse Remove Event Images The system is recording now please stop recording first It is the best to format the disk first before using it 27 6 Network General Device IP configuration includes DHCP Static IP setting and PPPoE Enable ARP Ping enable device to accept ARP or ping packets from the network Disable this option may provide extra security from intentional ping Live View Video Camera Event Hetwork Customize General Advanced 4MTP E Mail Service Static IP Address IP Address 192 168 2 102 Hetmask 295209422959 Gateway 0 0 0 0145 1 158 95 1 1 DHS 2 168 95 1 1 PPPoE User Name Password TH Mote Please make sure Email Setting has been set Enable ARP Ping After all settings are made please re
10. PiXORD H 264 Series 2 Megapixel Network Camera PL621 PL621E User s Manual Version 1 0 Date 09 04 2010 Contents INOUE CS rear a RR NT 2 LIO Bis oat 4 TriStar OM co uide qt o E pedi beoe MM 2 5 Usine the Neb S 10 EL CR I e C 11 dese EU T E 14 SINT T UU Um 14 PRIN NC 15 SA i210 E T T M MM mE 16 RSS INS TTE HER 16 Advan Dd lm 18 LM ISI mE 19 EV ce ica asset 19 Moton Dee TTE 21 T Ts 23 Eventt A 24 xm E eT 26 GENET MC 26 E 24 M MEME M ORE E 28 Ee eie aM 28 JN A CC ace ee 29 Vul N 31 BD cr 32 DINER Rr E 33 E TUM 33 e 34 PE 35 OIM RISUS NE IT 36 EOS SCE VACE C 37 eI COMM ZC corns 38 FA sasha ct
11. allation The following software is necessary for the proper display and use of the PL621 from the Web site The software will be taken from the Software Package CD IP Installer The IP Installer is used to locate and configure network cameras and video servers on the LAN This utility is useful for conveniently configuring the network settings of the device or for finding a device once the network settings have been modified To install the IP Installer from the Software Package CD UI select IP installer then follow the on screen instructions XVID Codec An H 264 codec is applied for displaying the video stream and playing the recoded AVI files If the video stream can t be displayed or the recorded AVI files can t be play on PC install this software from the Software Package CD VLC Though not necessary this can be used for viewing the streaming without a Web browser 3 Network Configuration IP Installer is a utility that provides an easier more efficient way to configure the IP address and network settings of the devices It even provides a convenient way to set the network settings for multiple devices simultaneously using the batch setting function Moreover IP Installer can save the network settings for all devices as a backup and restore them when necessary Preparation before IP Assignment 15 U 1 Always consult your network administrator before assigning an IP address to your server in order to avoi
12. amera Event Schedule Network System Customize Event Server Motion Detection 170 Ports Event Configuration Event Server List Hame Protocol Hetvork Address Upload Path User Hame AddFTP Remove Mote The maximum number of event servers is 10 Click Remove to delete selected event servers circled in red 20 Motion Detection O Live View Video Camera Event Je Event Server Motion Detection Event Configuration fresh Motion Detection List Windows Area Hame Note The maximum number of motion detections is 10 Set New Motion Detection Area 1 Click Add and rename the windows area 2 Drag a detection area on the image To add a motion detection area 1 Click on Add to set up a detection area Set up panel will be expanded 21 Motion Detection Setup Windows Area Name 2 Trigger Level qup 7077 1 Sensitivity 3 4 Im jo 7 Sensitivity value 0 100 low High Color 4 xm View All Windows View Selected Window 2 Give a name to this window area Select the trigger level and sensitivity for this detection window 07100 low high 4 Select color for detection window 5 Draw detection window on the image Live View Video Camera Event Event Server Motion Detection Event Configuration 6 Once everything is done click on Save to save the configuration made 22 Configured detecti
13. boot the camera to activate PPPoE You will receive email with IP address later 28 Advanced Enable or configure other network functions NTP Configure a NTP Network Time Protocol server so that the device system date and time can be synchronized with a specified Time Server This configuration is provided for one of the potions of system date time adjustment HTTP set the HTTP port that will be applied for Web UI access RTSP set the RTSP Video port for video data transmission HTTPS Enable Disable Http security function Bonjour Enable Bonjour service so that the device can be discovered with Bonjour service applied UPnP Enable UPnP so that the device can be discovered in an UPnP Compliant Network NAT Traversal Enable NAT traversal so that client from Internet can have access to the devices behind the Note with UPnP enabled the IP Sharing device Router capable of UPnP function will automatically be noticed with the device s NAT port 29 Live View Video Camera Event Network System Customize Advanced Obtain ATP server address via DHCP Use the following NTP server address Network address time stdtime tw host name or IP address HTTP Port RTSP Part Pee 30 SMTP E Mail Configure an email host in the device that will send email on behalf of the configured email account in a circumstance like sending an email notice to a specified mail addr
14. ce Adjust the white balance according to the environment Exposure Select the exposure frequency Max Exposure Time Increase reduce the exposure time for lens Max Gain Control image at low light control on how much noises are allowed Infrared IR Cut Filter IR will activate depending on the light sensor it is for better vision at night Color Mono Mode Switch among color mono or auto mode Video External Output Format Adjust the format according to the environment 18 4 Event ou uu Live View Video Camera Event Schedule Network Customize Event Server Motion Detection 170 Ports Event Configuration Event Server List Hame Protocol Hetwork Address Upload Path User Hame AddFTP Remove Hate The maximum number of event servers is 10 Event Server D Remove Mote The maximum number of event servers is 10 FIP Server Marcie HewFTP Server Network Address Upload Path Part 21 Login Information User Mame Guest Password Save Click on the Add FTP to expand server setting FTP Server gt Give a name for the FTP server gt Network Address Input the network address of the FTP server gt Upload Path Choose the desired upload path for events gt Port Input the port number of the FTP server 19 Login Information gt Username Password Input the username and password of the FTP Live View Video C
15. d using a previously assigned IP address Ensure the PL621 is powered on and correctly connected to the network MAC Address Each device has a unique Ethernet address MAC address shown on the label of the device as the serial number S N with 12 digits e g 000429 XXXXXX M N POF0512E030001 0004290000 Although the IP Installer is able to find and configure any PL621 in the LAN except those that are behind a router it is a good idea to set the host PC to the same subnet In order to connect to the Web based user interface of the camera the host PC must be in the same subnet For more information about subnets please consult your network administrator IP Installer to Assign an IP Address to PL621 Once IP Installer has been successfully installed on the PC double click the IP Installer icon on the desktop or select it from Start gt Programs gt IP Installer gt IP Installer gt Launch IP Installer IPInstaller exe Click the menu bar Tool Search Network Device to search the device in the LAN Untitled IPInstaller File Edit View T Search Network Device State Model fermi Subnet Mask Gateway Sameer oes Selec Led i Compare Selected 4 Serach Network Device From the list select the device with the MAC Address that corresponds to the device that is to be configured The MAC Address is identical
16. ess Event Configuration Sender Complete the Mail Server Server Port Authentication information if required and the sender email address Receiver the receiver email address Live View Video Camera Event Network Advanced SMTP E Mail SMTP email Setting Customize Mail Server smtphost yaurdamain name host name or IP address Server Port 0 65535 Authentication 31 DDNS Dynamic DNS configuration the network device can be assigned with a host name by registering this service Internet access required Host Name Assigned name that will be used for access to the device User Name Password Account authentication for logging to this service Update Time Periodically the device updates its access info to sever in the configured time the device responds the connection info Live View Video Camera Event Hetwork Customize General Advanced SMTP E Mail Dynamic ONS Setting C DONS Enable Link to http www dyndns org Update Time 600 86400 Seconds Response na 32 7 System Information Lists of System and Network configurations Live View video Lamera Information User System Model System up time Firmware version MAC Address Actives Control version Ethernet Status Mode IP Address Netmask Default Gateway DAS Server Primary DMS IP address Secondary IP address
17. k Camera delivers superior H 264 AVC performance state of the art design and function PL621 is specifically adapted for maximum performance indoor applications such as commercial banking government buildings schools universities and airports H 264 AVC video compression can lower bandwidth and storage requirements without compromising image quality Motion JPEG is supported for increased flexibility as well as multiple independent video streaming PL621 value added features include on board video motion detection SD slot for storage recording and two way audio P 600 PoE available full PoE IEEE 802 3af feature supplies power to the camera via the network eliminating the need for power cables reducing installation costs and complexity Consequently PL621 is Best in Class for maximum performance IP video surveillance systems demanding superior image quality ease of installation and intelligent video capabilities Installation 1 Hardware Connection gt w E Power 612 terminal p 2 E y 3 Video output B _ 5 Microphone input RED t i 1 AC M Audio output GREED Prepare a PC with Ethernet link to the network Connect LAN port RJ45 of the camera to a network switch hub Connect power jack Ensure the power adaptor specification matches the power system 110V or 220V and connect the adaptor to the outlet Check LED status Power Network 2 Software Inst
18. of fire or shock circuit Toreduce the risk of electric shock do not remove the Cover or Back No user serviceable parts inside Misusage improper and negligence could damage this equipment Need to refer servicing to qualified service personnel gt gt continue to operate if there appears to be fault If the unit ceases to function contact qualified service personnel for help All work related to the installation of this product should be made by qualified service personnel or system installers Liability PiXORD Corporation reserves the right to make corrections modifications enhancements improvements and other changes to its products and services at any time and to discontinue any product or service without notice Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete All products are sold subject to PIXORD Corporation s terms and conditions of sale supplied at the time of order acknowledgment PiXORD is not responsible or liable for the resale of its products with statements different from or beyond the specification parameters stated by Customers are responsible for their applications using PIXORD products To minimize the risks associated with customer applications customers should provide adequate operating safeguards is under no obligation to provide any further technical support service or prod
19. ok or use custom settings Live View ideo Camera Event Schedule Network System Customize Live View Layout Setting Use Default Look Q Use Custom Settings User Defined Links show Custom Link 1 Mame Custom Link 0 URL show Custom Link 2 Mame Custom Link 1 URL show Custom Link 3 Mame Custom Link 2 URL show Custom Link 4 Mame Custom Link URL Save Use Default Look the default layout of live configuration pages Use Defined Links Web link s will be presented on the live page when enabled It can be a link to another IP camera for instance or other preferred web link 38 Use Custom Settings The modifications allowed are change of Background Text Color Background picture Use Custom Settings Mame Custom Link 0 URL Title Description Logo and etc Live View Layout 5etting Q Use Default Look User Defined Links Show Custom Link 1 Show Custom Link 2 Mame Custom Link 1 URL show Custom Link 3 Mame Custom Link 2 URL show Custom Link Marne Custam Li URL https Custom Settings Modify the Default Lack Background Calor 9 Default Eram Text Color Default Q own Background picture Hane Q External http Titla Hone Default own Title Descriptian Nane Default own Description Logo Link None Default Q own http
20. on window will be displayed in motion detection list circle in blue Motion Detection List Windows Area Hame qu Add Del Nate The maximum number of mation detectians is 10 Set Mew Motion Detection Ares 1 click Add and rename the windows area 2 Drag detection area on the image Note Maximum number of detection window is 10 I O Ports RES Live View Video Lamera Event i Event 5erver Motion Detection 170 Ports Event Configuration Input Ports Setting 1 Schedule Network Customize Marne Inputi Current State high Input Ports 5etting 2 Marne Inputz Current State high Output Ports Setting Mame OQutputl law Current State Input Ports Setting 1 and 2 gt The name of Digital Input1 2 gt Current State Current Input state Output Ports Setting gt The name of relay output gt Current State Current Output state 23 Event Configuration Live View Video Camera Customize Event 5erver Motion Detection 170 Ports Event Configuration Event Record File File Format JPEG Event Type List Hame Status Enable Trigger Actions 1 Remove im e maximum number of events is 10 Fu FTP Upload Hu HTTP Upload Eu Email Upload G Gutput Part En Email Notification Hn HTTP Notification Tn TCP Notification To add an event trigger click on Add and setup panel will be expanded 24 Event T
21. to the unit s S N Serial Number Double click the item to open the Property Page for the selected device or click the menu bar View gt Property we Untitled IF Installer Ga Toolbar Es AA gm __ Situs IP Ad ms SgubnetMssk onsi pN32 192 168 294 4552553255 192168 2254 192169013 192 1868 0 16 192 165 2 95 235 45532550 192168 2254 19 168 0 13 168 95 1 1 PEE 192 166 2 142 255255255 19216852254 192169013 1868 35 1 1 hese eee lla 192 165 2 31 235 45532550 192168 2254 192169013 192 16 0 16 FAQODN O0 04 29 00 8c ff 192 168 2 90 255 255 2550 1921682254 15685511 158 395 1 1 AID After filling in the properties click Set button to complete the configuration settings in the remote device while saving configuration in the PC If click Close button the configuration is only be saved in the PC Property Page porn Addr ELLL L U V 00 04 29 01 08 Cancel Firmware Version cet 0 2 rc5 4381 Property IP Address 192 168 2 155 Subnet Mask 255 255 255 0 Gateway 192 168 2 25d Http DNS 192 168 0 13 DNS 192 168 0 16 LINS3 158 85 1 1 amp Password Use Custom Username admin Password Open the Web based UI of the Selected camera To access the Web based UI of the selected unit run the View
22. uct software alteration beyond PiXORD s representation PiXORD products are not authorized for use in safety critical applications where a failure of the PIXORD product would cause severe personal injury or death unless officers of the parties have executed an agreement specifically governing such use Reproduction of PIXORD information or datasheets with alteration is an unfair and deceptive business practice is not responsible or liable for any such statements Every care has been taken of this manual If there are any inaccuracies or omissions please inform your local office PIXORD Corporation cannot be held responsible for any typographical or technical errors PIXORD Corporation is not liable or responsible for incidental or damages caused by mishandling Trademarks All names used in this manual for hardware and software are probably registered trademarks of respective companies PiXORD is a registered trademark of PIXORD corporation All rights reserved Support If you require any technical assistance please contact your reseller You can connect to the Internet PiXORD s website www pixord com for below information e Download user documentation and firmware updates at PIXORD Support http www pixord com support support asp Find answers to resolved problems in the FAQ database Or contact our FAE at technical support http www pixord com contact2 asp Introduction PL621 Networ
23. udio Enable Web Record Setting Save Path Fila Marne Browse Web Snapshot Image Setting Save Path File Marne Browse 16 Camera General Setting gt Brightness hue and saturation Adjust the image for a better view gt Rotation 180 Rotate the image by 180 degrees so that the image becomes upside down This function is useful when camera device must be physically installed in vertically reversed direction Audio Setting gt Audio Enable Turn on off the audio Web Record Setting gt Save Path File name Click on the Browse button to select the desired path to save as well as naming the video file Web Snapshot Image Setting gt Save Path File name Click on the Browse button to select the desired path to save as well as naming the snapshot Default gt Set camera general setting and audio setting back to default Note Will not change the configuration of Web Record Setting and web Snapshot Image Setting Save gt Save the changes that have been made 17 Advance Live View Video Camera Event Network System Customize Camera Advanced Setting White balance Aute Exposure Flicker free 50 Hz Max Exposure Time 1 30 5 Gain Control dB Infrared IR Cut Filter Auto Color Mono Moder Aute Video External Output Setting Video External Output Format White balan
24. ype 5etup m 00 00 00 Set min time between maera max 23 59 59 Respond to Trigger 4 9 Only during time frame Start Time max 23 59 59 Duration max 168 00 08 5 Never Trigger by When Triggered 6 Upload Images Activate Output Port Save 2 Give a name to this event 3 Set the time interval between each trigger 4 Set the time period for the trigger Choose Always During time frame or Never During time frame Choose a day and the starting time then configure the duration time 168hrs 24 7 For example if duration time is set to 168 hrs it is the same as choosing Always 5 Choose the triggering condition GPIN Manual trigger Motion detection and On boot 6 Choose the triggered event Upload images Active Output port Send email notification 7 Finally click on Save to save the configuration made 25 5 Schedule General Define the day specified by days of a week and time specified by each single hour for that will be recording during the scheduled period Note that only video data will be recorded User can select which video stream should be recorded and the size of each sliced file When the check box is ticked and setting is saved recording process starts Recording files are saved to the SD storage Network Customize Live View Video Lamera Event Schedule General Storage
Download Pdf Manuals
Related Search