US Steam ES2100 Steam Cleaner Owner`s Manual
Contents
1. 13 ES2100 OPERA nce cece ate 15 ES 1900 OPERATION jivapesecswidicuceuzsolsitvweverses bidenrvenneesideiuueuerbsiveewuernensead 16 100 OPERATION 17 ES1900 ES2100 ES6100 MAINTENANCE 18 WARRANTY 19 EUROSTEAM TRAINING MANUAL Page 3 of 20 EUROSTEAM US STEAM SANITIZED FOR HEALTH REDEFINED SECTION I THE EUROSTEAM UNIT I HOW TO START UP THE EUROSTEAM a Make sure the unit is unplugged plus the POWER switch is off b Remove the top cap c Fill unit with water using the filler bottle d Press gently down the bottle to release water through the spill proof cap or use funnel e Fill until 2 1 below top of tank Hand tighten the top cap hand tighten ONLY f Plug the unit into a grounded 120V outlet If you use an extension cord the heating will take longer time Turn the heating switch on Extension cord maximum 50 10 gauge extension cord g Wait until the green light is on pressure gauge should be between 4 and 5 h Warm up time is usually 15 minutes i Insert the flexible hose into the unit connection front left side of EUROSTEAM unit clicks into place j Now bleed the system by using high pressure 51900 amp ES2100 press both switches forward on the hose handle ES4500 turn steam control knob to HIGH all the2. jurisdiction and venue of the state COURTS of Texas to resolve any and all customer disputes with seller and THE customer waives all defenses to such jurisdiction and venue including but not limited TO any defense based on INCONVENIENT forum In the event the customer and seller are unable to resolve any customer dispute and any collection action suit or other judicial PROCEEDING is commenced the prevailing party in any such action suit or judicial proceeding shall be entitled to recover its costs and reasonable attorney s fees incurred EUROSTEAM TRAINING MANUAL Page 20 of 20
3. FIXTURES Using the 1 hole nozzle blow out around faucet and fixture detail areas Add 1 inch nylon brush for light scrubbing on chrome or brass fixtures soap containers etc BATHTUB FIBERGLASS SHOWER AND BATHTUB INSERTS Mist area with EUROSTEAM VAPORMATE Using the 1 hole nozzle blow out detail areas Add 1 inch nylon brush for fixtures Next using a 3 hole nozzle with 3 inch round or 3 inch triangle brush start from top with a light scrubbing action Wipe cleaned area with cotton towel as you go SILICONE SEALANT Using a 1 hole nozzle no closer than one inch use back and forth movement blowing out debris NOTE DO NOT OVERHEAT SEALANT IF MOLD AND MILDEW DOES NOT COME OFF WHILE CLEANING HEAT WILL KILL THE GROWTH GLASS SHOWER DOORS Mist with EUROSTEAM VAPORMATE Pre heat glass with glass attachment keeping attachment 2 to 3 inches away Using 3 inch round or 3 inch triangle brush start from top of door using light scrubbing action Wipe cleaned areas as you go Work quickly so as to keep heat to a minimum while cleaning TOILET Mist with EUROSTEAM VAPORMATE Using 3 inch round or 3 inch triangle brush start from top using light scrubbing action Wipe cleaned area as you go NOTE ALWAYS CLEAN 2 FOOT RADIUS OF FLOOR AROUND TOILET TO KILL BACTERIA FLOORS WAXED FLOORS Use large floor brush and incorporate the 2 inch round brush if necessary in corners and tight areas Spray EUROSTEAM VAPORMATE lightly on area to be cleaned
4. Vapor Steam Systems and Cart System sold by the seller Seller will be free from defects in materials and workmanship for a period of eighteen 12 months from the date EUS receives the product warranty card not to exceed Twenty 18 months from the date of sale Pressure Tank will be covered under warranty for a period of 3 years Thirty six 36 months from the date of sale from manufactures defects TERMS OF LIMITED WARRANTY The limited warranty becomes effective upon receipt of the System by Customer is granted to the initial Customer end user and is transferable with notification of new ownership Any claims under this warranty must be made before the end of the applicable warranty period During such period if EUS determines that a part or System is defective in material or workmanship EUS at its option will provide Customer with a repaired part or System or replace any part of the System that is covered by the limited warranty EUS reserves the right to substitute functionally equivalent new or serviceable reconditioned parts or systems ESS s responsibility is limited to repair replacement credit or refund any of which may be selected by EUS at its sole discretion The limited warranty covers only defects arising from normal use and does not include malfunctions or failures arising from misuse abuse neglect alteration mineral build up from neglect usage not in accordance with user manual and instructions depletion
5. not stay on one spot too long NON WASHABLE Use triangle brush with 1 towel Preheat towel and wipe with no steam Move quickly with smooth strokes Do not stay on one spot too long PAINTED WALLS AND CEILINGS CAUTION THE HEAT MAY REMOVE SOME PAINT IF IT IS THIN OIL PAINT Use large or triangle brush with 1 towel on low to medium pressure and wipe Do not stay on one spot too long Use extension tubes to reach ceilings LATEX PAINT Use large or triangle brush with 1 towel Preheat towel and wipe with no steam Do not apply pressure Move quickly with smooth strokes Or use nozzle on high pressure 5 off surface to pre steam spot Do not get surface too wet Wipe gently with towel TRACKS MOLDINGS TRACKS Use 1 hole nozzle with detail brush on medium pressure Wipe cleansed area immediately with towel MOLDINGS Use 1 nozzle on medium to high pressure Hold the nozzle in one hand and a towel in the other hand Move the nozzle and towel at the same time in one direction blowing the dirt into the towel Hold the nozzle parallel to surface Move quickly Wipe with dry towel WINDOWS AND WINDOW FRAMES CAUTION ALWAYS PREHEAT GLASS WITH THE SQUEEGEE 2 3 INCHES FROM SURFACE BEFORE CLEANING DO NOT CLEAN GLASS WHEN TEMPERATURES ARE BELOW FREEZING POINT NEVER CLEAN A GLASS THAT HAS A CRACK GLASS MAINTENANCE Use window squeegee on low to medium pressure and go over window Turn off steam re squeegee window and wipe excess wate
6. ANCE IS ALREADY GONE AND THE CARPET SHOULD BE RE TREATED AFTER IT IS CLEANED Use same technique as Industrial Type carpet but do not stay on one spot too long NON COLORFAST Use nozzle 2 4 above carpet on high pressure and shoot steam from the side with quick side to side movements lengthwise and crosswise Hold a towel to the side to catch all dirt particles as they blow out of the carpet Do not get closer than 2 with the nozzle Fluff up the fibers evenly with a dry towel DELICATE CARPETS Not Recommended for Silk EUROSTEAM TRAINING MANUAL Page 10 of 20 EUROSTEAM SANITIZED FOR HEALTH REDEFINED Use large rectangular brush with diapered towel Preheat towels and wipe with no steam Wait a few minutes To dry use the triangle brush with 1 towel without steam and wipe with vertical and diagonal strokes WALLS amp CEILINGS NEVER USE BRUSHES WITHOUT A TOWEL ON PAINTED SURFACES ALWAYS USE 2 TOWELS ON THE RECTANGULAR BRUSHES WALLPAPER WASHABLE Use rectangular or triangle brush with one towel Preheat towels and wipe with no steam or low pressure Use smooth rapid strokes For spot cleaning use nozzle on high pressure 5 off surface to pre steam spot wipe immediately with towel DEEP CLEANING If surface is heavily soiled pre steam surface or spray the towel with biodegradable soap Follow up with a clean towel to remove soap residue If wallpaper is textured pre steam 2 off surface Wipe with towel Do
7. ARNINGS 1 DO leave the steam cleaner unattended while plugged in Turn off all controls and unplug the electrical cord when not in use when moving to another location and before servicing 2 DO use with a damaged cord or plug If the steam cleaner is not working as it should has been dropped damaged left outdoors or dropped into water call for service before using 3 NEVER attempt to disassemble this product in a way not instructed in this manual 4 DO handle the plug with wet hands 5 DO allow this steam cleaner to be used as a toy DO NOT use near children 4 DONOT pull or carry by cord Keep cord away from heated surfaces 5 DO use extension cords greater than 25 ft or cords or outlets with inadequate current carrying capacity 12 gauge capacity and must have ground wire capabilities 6 DO add anything other than clean drinkable water to the boiler tank see Water Conditioning Section on p 5 of the Manual 7 DO add water to boiler while boiler is hot 8 NEVER unscrew the safety cap while boiler tank is under pressure 9 See Refill Section on Page 3 of this manual 10 Keep body away from nozzle or brush steam Steam can cause burns 11 ALWAYS set safety switch on hose handle to the forward or locked position when not in use Not setting safety switch to locked position could result in an injury 12 ALWAYS test a small area before cleaning a large area on any type
8. Clip a clean cotton towel over the large floor brush Apply medium steam and quickly adjust to low steam cleaning a small area quickly as you go This should melt a top layer of wax holding the dirt in the pores of the floor If the floor is greasy or very dirty you may need to repeat this procedure UNWAXED VINYL FLOORS Apply EUROSTEAM VAPORMATE to area to be cleaned Use the large floor brush with no towel on medium steam HINT Place a rectangle scrubber pad inside the bristles of the large brush This will agitate the dirt and grime Use a back and forth motion Wipe cleaned area with a cotton towel as you go NOTE DO NOT OVERHEAT ANY KIND OF VINYL SINCE THIS COULD SOFTEN THE SURFACE AND AFFECT THE TEXTURE THIS ALSO APPLIES WHEN USING SMALL BRUSHES TO REMOVE TOUGH SPOTS WOOD PARQUET FLOORS Use large brush with a cotton towel clipped over it and low steam Move quickly to avoid heat or moisture buildup in wood If the floor is greasy or very dirty spray towel with EUROSTEAM VAPORMATE MARBLE FLOORS Use the same techniques as used for wood parquet floors keeping heat and moisture off the surface as much as possible NOTE SOME MARBLE SURFACES CAN DISCOLOR TEST A SMALL NON CONSPICUOUS AREA FIRST EUROSTEAM TRAINING MANUAL Page 9 of 20 EUROSTEAM US STEAM SANITIZED FOR HEALTH REDEFINED CARPETS Always VACUUM carpet first Always TEST an area for discoloring before cleaning Some carpets are made with vegetable dyes which are no
9. EUROSTEAM US STEAM TRAINING MANUAL MODELS ES1900 ES2100 ES4500 ES6100 EUROSTEAM US Steam Sanitized for Health REDEFINED Vapor Steam Systems and Solutions Since 1992 EUROSTEAM US STEAM 110 South Hampton Crowley TX 76036 800 613 3874 EUROSTEAM COM EUROSTEAMIUS STEAM SANITIZED FOR HEALTH REDEFINED PRECAUTIONS KEEP THESE INSTRUCTIONS Read these instructions carefully before using the appliance and make sure that anyone using the machine is familiar with these instructions and warnings KEEP FOR YOUR RECORDS THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE PLEASE READ UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS MANUAL BEFORE USING THIS VAPOR STEAM CLEANER DO NOT USE THE STEAM FUNCTION ON DRAYLON VELVET LEATHER OR OTHER SENSITIVE FABRICS In order to reduce the risk of fire electric shock personal injury or damage to property follow these instructions carefully When using electrical appliances basic safety precautions should be followed including the following NOTICES 1 Read all instructions before using this steam cleaner Save these instructions for future reference 2 View instructional video before operating this steam cleaner 3 Use of any replacement parts other than authorized Eurosteam parts voids all warranties and can cause bodily injury to the operator and damage equipment Service performed by anyone other than factory authorized personnel will void warranty W
10. MER The ES4500 delivers the next generation cleaning and sanitation solution It utilizes Dry Steam only 6 water vapor to efficiently clean and sanitize The ES4500 s patent pending technology can apply cleaners antimicrobial coatings and eco friendly sanitation products with steam enhancing their effectiveness THE ES4500 ADDITIVE TANK STEAM PRESSURE CONTROL KNOB BOILER REFILL CAP Turn to the right to INCREASE SWITCH 1 Boiler ON Off SWITCH 2 Steam Release ON Off LOW WATER LIGHT SWITCH 3 Additive ON OFF GREEN READY LIGHT ADDITIVE CONTROL KNOB Turn right to DECREASE amount HOSE CONNECTION PRESSURE GUAGE PREPARING THE ES4500 FOR USE a Make sure the unit is unplugged plus the POWER switch is off b Remove the Water Filler cap NOTE If unit is warm let pressure gauge go down to 0 and machine cool off before proceeding c Remove Water Filler Cap and fill unit with water using the Filler Bottle d Press gently down the bottle to release water through the spill proof cap or use funnel Fill until 2 1 below top of tank f Hand tighten the Water Filler Cap hand tighten ONLY FILLING THE ADDITIVE TANK a Remove the cap from the additive tank plastic container on the back of the ES4500 b Use the small funnel to fill the Additive Tank with the EJUROSTEAM approved additive c Screw the red tank cap on carefully d Insert the feed line into the back of the ES4500 the mono plug will c
11. TRINGS Pull the blind all the way up Wipe the string with a towel wet with EUROSTEAM VAPORMATE Pull the string slowly through a detail brush on medium pressure DRAPES NOTE VACUUM DRAPES FIRST SHEER ONE PLY FABRIC Use triangle brush with one towel on low or medium pressure on one side of the pleat AND use the large rectangular brush with one towel on the other side to hold curtain steady Move both brushes at the same time from top to bottom at medium speed The steam will go through the fabric and remove dirt from both sides simultaneously INSULATED MULTIPLE LAYERED FABRIC Same technique as SHEER 9 1 but do not move too slow since the insulation is generally heat sensitive Go over surface twice FURNITURE UPHOLSTERY NOTE ALWAYS CHECK AREA FOR SCOTCH GUARDING Using large triangle brush with diapered towel heat towel on high 3 to 5 seconds Clean furniture on low pressure using back and forth movement If material seems to be getting too wet cut steam off Reheat towel as needed LEATHER Using 1 hole nozzle blow out cracks and crevasses Clean the same as upholstery VINYL Using 1 hole nozzle blow out cracks and crevasses Use appropriate brush according to the amount of surface cleaning and amount of dirt on material EUROSTEAM TRAINING MANUAL Page 12 of 20 EUROSTEAM SANITIZED FOR HEALTH REDEFINED SECTION Ill THE ES4500 CLEANING AND MAINTENANCE DRY VAPOR CLEANER SANITIZER AND ADDITIVE APPLICATION STEA
12. are accessible by the operator Cleaning e Make sure unit is cool e Unscrew drain plug and drain excess water from the tank Replace drain plug e Weekly Cleaning Add 1 cup CLR quart of water let sit for 15 minutes This method is not recommended for the ES6100 e Un screw drain plug located on bottom of unit and rinse thoroughly EUROSTEAM TRAINING MANUAL Page 18 of 20 EUROSTEAM SANITIZED FOR HEALTH REDEFINED US Steam Maintenance And Water Recommendations Water Conditioning It is essential to supply US Steam Systems with clean low mineral content water to help prevent scale build up Even though US Steam Systems are engineered to minimize scale formation scale development depends on the hardness of your water and the number of hours the equipment operates Most tap water sources are full of minerals which form scale during operation It is this scale which could lead to early component failure We recommend using distilled water which will provide longer life to the unit higher steam capacity and reduce maintenance requirements If you notice a reduction in steam production check the unit for scale build up Heavy scale reduces the unit s ability to boil water and may cause the heating element to overheat and burn out Pre cautions 1 Never unscrew cap while boiler tank is under pressure 2 Keep hands away from steam coming out of turbo nozzles steam can cause burns 3 Always protect hands when chan
13. face is sensitive to heat like wood paint wall paper color fabric and plastic WIPE Remember to always wipe the area you just cleaned All surfaces have pores even glass The works by the hot steam opening and cleaning deep into the pores Wipe off dirt immediately before the surface cools down Once surface reaches the right temperature soil is released moisture from the steam surrounds soil and at this point the terry towel is your vacuum wipe surface with towel OTHER EQUIPMENT Vacuum Vacuum floors and other surfaces before steam cleaning VI CHEMICALS VERY IMPORTANT NEVER ADD CHEMICALS INTO THE BOILER TANK It will void the warranty and could result in malfunction or damage to the system NOTE THE ES4500 has a tank in the back of the unit for EUROSTEAM approved chemicals Go to Eurosteam com for an up to date of approved chemicals At the printing of this document the approved chemical additives are e SaniShield Anti Microbial Coating e Goldshield Anti Microbial Coating e Vapormate For most of the jobs you do not need to use chemicals together with the system When do use chemicals avoid harsh toxic chemicals We recommend using Eurosteam Vapormate see Appendix A Vapormate Data sheet VII NATURAL CHEMICAL SUBSTITUTES Use Natural Chemical Substitutes to pre treat surfaces prior to the steam application NEVER ADD CHEMICALS INTO THE BOILER TANK BLEACH Lemon juice i
14. ging accessories after use 4 Extension cords must be used at a maximum length of 25ft with 12 gauge capacity and have ground plug capability 5 Never unscrew drain plug while water in boiler is hot or pressure gauge reads over 0 6 Allow machine to cool before de scaling tank 7 Do not add anything other than clean water or CLR into the boiler 8 Before cleaning outside of unit disconnect electric power supply Keep water and cleaning solutions out of controls and electrical switches 9 Use of any replacement parts other than US Steam parts supplied by US Steam or their authorized business partners voids all warranties and can cause bodily injury to the operator and damage the equipment Service performed by anyone other than factory authorized personnel will void all warranties 10 Do not expose machine to freezing temperatures Weekly Cleaning Make sure unit is cool Unscrew drain plug and drain excess water from the tank Replace drain plug Add 1 quart of water shake unit to release minerals from element Remove drain plug and rinse unit until water is clear of any mineral replace drains plug Drain plug has rubber o ring do not over tighten EUROSTEAM TRAINING MANUAL Page 19 of 20 EUROSTEAM US STEAM SANITIZED FOR HEALTH REDEFINED EUROSTEAM US STEAM PRODUCT WARRANTY STANDARD TERMS AND CONDITIONS TWELVE MONTHS LIMITED WARRANTY Austin K Inc DBA Eurosteam US Steam EUS warrants that the EUROSTEAM US STEAM
15. he middle position Monitor the pressure gauge If pressure drops below 2 0 bars turn hose switch lock Wait for pressure to rebuild before using HIGH PRESSURE again MEDIUM PRESSURE is generally enough for most cleaning jobs Use HIGH PRESSURE to pre steam heavily soiled areas to preheat towels on the brushes and to blow out dirt from hard to reach areas IV TEMPERATURE The temperature of the steam at the tip of the nozzle is between 185 235 depending on accessory used but since the vapor is so dry it cools to under 100 F approximately 9 10 inches from the tip A preheated towel on a brush will cool to under 150 F within seconds after the steam is turned off Use this method to regulate the temperature you apply to surfaces where heat is a concern like paint wood plastic etc EUROSTEAM TRAINING MANUAL Page 4 of 20 EUROSTEAM SANITIZED FOR HEALTH REDEFINED V WORK TECHNIQUES Work from the top down on any project so dirt will not fall on cleaned surfaces Start with cleaning corners and other tight areas first with the nozzle and small brushes working your way up to larger surfaces and brushes PRE STEAM Get a habit of pre steaming a surface if it is heavily soiled At a 5 distance shoot steam on surface from all directions for 10 seconds on HIGH PRESSURE Depending on the size of surface use nozzle triangle or rectangular brush SPEED Let the heat do the work for you Do not move too quickly unless sur
16. itch is in the on position d Adjust the additive flow by turning the Additive Control Knob turn all the way clockwise is the minimized position e Adjust the steam flow by turning the Steam Pressure Control Knob all the way right to the right is the maximum flow position RECOMMEND MEDIUM PRESSURE 1 TURN f Start using the EUROSTEAM to dispensing the additive if more additive is needed increase the flow by turning the Additive Control Knob to the left increasing the flow to the desired position TURNING OFF THE STEAM ADDITIVE FUNCTION AND RINSING THE ADDITIVE FROM INSIDE THE ES4500 After each use it is important to rinse the additive from the pump dispenser tube path This prevents the additive from clogging up the dispensing mechanism not to mention guarantees the next time the unit is used it is ONLY dispensing the desired additive a Unscrew the red cap from the Additive Tank leave the dispenser hose attached b Place the end of the dispenser cap in a cup of water c Turn the Additive Control Knob setting to HIGH turn all the way to the left d Place the nozzle of the ES4500 in another cup and operate until the cup in the back is empty e NOTE this will flush all the additive from the pump dispenser tubing and unit f Turn off Switch 3 Additive Switch 2 Pressure and Switches 1 Boiler FREEING A CLOG IN THE ADDITIVE DISPENSER PATH If the ES4500 is not cleaned the ADDITIVE DISPENSER PATH can become cl
17. lick into place STARTING THE EUROSTEAM UNIT a Plug the unit into a grounded 120V outlet If you use an extension cord the heating will take longer time Turn the heating switch on Use a maximum 50 10 gauge extension cord b Turn Switch 1 Boiler Switch to ON yellow light will be display when switch is in the on position c Wait until the Maximum Pressure Light is on pressure gauge should be between 4 and 5 d Warm up time is usually 15 minutes e Insert the Steamer Flexible hose into the Hose Connection connection clicks into place EUROSTEAM TRAINING MANUAL Page 13 of 20 EUROSTEAM US STEAM SANITIZED FOR HEALTH REDEFINED f Turn Switch 2 Steam Release to ON yellow light will be displayed when switch is in the on position g Bleed the system by using high pressure ES1900 ES2100 press both switches the hose handle ES4500 turn Pressure Control knob to HIGH all the way to the right h Press the trigger to remove water residue from the hose into towel for about 5 seconds i Wait until MAXIUM PRESSURE lights again before starting to clean j Now the system is ready for any cleaning task k COMBINING STEAM ADDITIVE FUNCTION To combine the additive in the tank with the steam a Fill the Additive Tank with the Eurosteam approved additive b Place the Red Cap on the Additive Tank and tighten the Cap c Turn Switch 3 Additive Switch to ON yellow light will be displayed when sw
18. mperature dirt will release and be Surrounded by the moisture of the steam Wipe with towel as you clean GROUT To clean floor grout attach 2 extensions to hose attach single hole nozzle with one inch brush to last extension Start in one corner cleaning a 3 FT to 4 FT square at a time Spray grout with Vapormate set steam on Medium to High Set brush on grout line turn brush at angle as if to blow dirt on tile and push away from you When pulling back to you turn at opposite angle 2 times up and 2 times back should clean grout excessively dirty grout make take longer to clean 1 INCH BRASS BRUSH Oven interiors BBQ grills and other non scratch surfaces Use with 1 hole nozzle Use Vapormate on surface as you clean Using med high steam move across surface to be cleaned making sure to cover all areas Let the heat do the work for you once the surface reaches the correct temperature dirt will release and be Surrounded by the moisture of the steam Wipe with towel as you clean 3 HOLE NOZZLE Use with small triangle brush or 3 inch round brush when multi directional cleaning action is needed 3 INCH ROUND BRUSH Attach the 3 hole nozzle to the hose handle and then the brush to the nozzle Set the steam dial to medium or high pressure ps kitchen or bathroom sinks dishwasher igerators fiberg porcelain bathtubs and glass shower doors Use Vapormate on surface as you clean Using med high steam move across surface to be cleaned making
19. nd button B is for Low steam pressure and manual Pulse action NOTE High Steam is activated by placing both A and B buttons in the forward position 7 High Pressure Water Turn all 3 machine switches 1 2 3 the Position push hose button A forward to release water and steam press button B to the forward position or press down using the pulse for water when needed EUROSTEAM TRAINING MANUAL Page 15 of 20 EUROSTEAM US STEAM SANITIZED FOR HEALTH REDEFINED ES1900 Controls There are two sets of operator controls the first set of two buttons are located on the front of the unit First button 1 heats the element in the pressure vessel Heating element button Second button 2 allows the steam to reach the hose Steam button Green light 4 illuminates when pressure is correct and machine is ready to use Yellow light 5 illuminates when unit is low on water OONA AS 5 A 2 AN W w mu The second set of two buttons is located on the hose handle 3 First button A is for Medium steam pressure 4 Second button B is for Low steam pressure and manual Pulse action NOTE High Steam is activated by placing both A and B buttons in the forward position EUROSTEAM TRAINING MANUAL Page 16 of 20 EUROSTEAM SANITIZED FOR HEALTH REDEFINED ES6100 Controls There are two sets of operator controls the first set of two buttons are located on the front
20. ng Diaper a towel around brush using clips before connecting to hose turn on steam and bleed hose Attach large triangle move slow across mattress make sure get all corners and crevasse Change towel often to keep moisture from soaking mattress Upholstered items Use same technique as mattress cleaning High Heat Sanitizing Diaper towel around attachment this creates highest amount of heat to sanitize countertops walls floor rugs bathrooms Slide on to the bottom of the large rectangular brush to kill dust mites and mold spores in carpets EXTENSION WANDS Use with any nozzle brush combination to extend reach for pone floors walls and ceilings Can use up to 3 wands at a time Two wands come in the standard package SQUEEGEE For windows and glass TOOL cleaning and sanitizing drains pipes and sinks NOTE USE DANCO WATERPROOF GREASE FAUCET REPAIR to lubricate hose nozzle wands and accessories CLEANING OF ACCESSORIES There are a number of options to clean the accessories Get in the habit of cleaning brushes BEFORE the dirt dries on them e Use the single hole nozzle clean out brushes using high steam e All accessories can be cleaned in the dishwasher except the flexible hose EUROSTEAM TRAINING MANUAL Page 7 of 20 EUROSTEAM US STEAM SANITIZED FOR HEALTH REDEFINED SECTION II APPLICATION TIPS amp PRECAUTIONS IX DISTILLED WATER We recommend using de mineralized or distilled
21. of Consumables accessories acts of nature or damage caused by repairs where such repairs were made without EUS s express approval The Warranty does not cover defects or damage arising from the disassembly or attempted disassembly of products without EUS approval WARRANTY SUPPORT PROCEDURES If support is required for the System call Eurosteam US Steam Customer Service at 1 800 613 3874 Have the serial number and proof of purchase available A customer service representative will troubleshoot the problem and determine if the product should be returned for further diagnosis The customer service representative will advise you if you should ship your machine to a local service center or return it to the central repair facility DO NOT SHIP THE SYSTEM OR ANY SYSTEM COMPONENT TO ANY REPAIR FACILITY WITHOUT FIRST RECEIVING A RETURN AUTHORIZATION NUMBER FROM A EUROSTEAM CUSTOMER SERVICE REPRESENTATIVE RETURN PROCEDURES Prior to shipping the System or a System component to any repair center for warranty service Customer must contact Eurosteam US Steam Customer Service at 1 800 613 3874 to receive a Return Authorization number and specific instructions on how to package and ship the System to avoid further damage The Customer Service Representative will provide instructions to drain all water from the boiler tank pack the System in original packing material and ensure that the System wheels are protected so as to minimize potential shipping damage to
22. of surface to make sure no damage will occur 13 DO NOT expose machine to freezing temperatures while not in use 14 DO NOT store gasoline or other flammable vapors and liquids the vicinity of this or any other appliance ELECTRICAL CONNECTIONS The steam cleaner uses 110 Volts and will pull 12 9 Amps when starting It should be the only appliance plugged into an outlet 1 Any alteration of electrical cord supply on this steam cleaner will void all warranties 2 Once electrical hook up meets requirements make sure all switches on front of unit are in the off position before plugging unit into electrical outlet 3 For circuit breaker protection if possible plug the unit into an outlet isolated from other equipment or turn the other equipment off while using the steam cleaner the combined electrical amperage of other equipment and the steam cleaner together may cause a circuit breaker to trip 4 Always press Switch 1 to OFF before you unplug the unit EUROSTEAM TRAINING MANUAL Page 2 of 20 EUROSTEAM SANITIZED FOR HEALTH REDEFINED EUROSTEAM US STEAM TRAINING MANUAL TABLE OF CONTENTS CONTENT PAGE SECTION IF UNIT INFORMATION entre rceceacceeenesndinpenuenenateceeease 4 TOOL USE GUIDE 6 SECTION 11 APPLICATION TIPS amp 9 SECTION 111 THE ES4500 OPERATION amp
23. of the unit 10 First button 1 heats the element in the pressure vessel Heating element button 11 Second button 2 allows the steam to reach the hose Steam button 12 Green light 4 illuminates when pressure is correct and machine is ready to use 13 Yellow light 5 illuminates when unit is low on water water can be added to the ES6100 without shutting unit off ES6100 control for steam is located on top of unit turn knob to position for high steam and towards position for low steam Once desired steam is set red button A on hose handle control release of steam Note Once the ES6100 cools down water will siphon into the boiler this may cause unit not to release steam immediately on next use If you do not get immediate steam on next heat up 1 Hold hose handle over sink or drain 2 Press hose buttons to high position 3 Run on high until water stops and steam flows EUROSTEAM TRAINING MANUAL Page 17 of 20 EUROSTEAM US STEAM SANITIZED FOR HEALTH REDEFINED The ES6100 ES1900 and ES2100 are designed for minimum maintenance and no user adjustments should be necessary Certain parts may need replacement after prolonged use If there is a need for service only Eurosteam service personnel or authorized Eurosteam service agents should perform the work Always use water with a low mineral count that meets the standards outlined in the Water Conditioning section of this manual This unit contains no fuses that
24. ogged the dispenser tubing and pump To clear the ES4500 additive dispenser path a Make sure ES4500 is on and warmed up pressure gauge is between 4 and 5 b Bleed the ES4500 by pressing the trigger and letting out the steam for 5 seconds c Wait until the MAXIMUM PRESSURE light is on again d Remove the mono plug from the back of the unit e Unplug the Black mono plug at the end of the additive tank plugged into the ES4500 f Place the single hole nozzle on the ES4500 g Place the nozzle in the hole for the mono plug was plugged into h Turn on Switch 3 Additive Switch i Blow steam into the unit by pull the trigger and letting the ES4500 operate until the pressure is flowing freely through the Additive Dispenser Path EUROSTEAM TRAINING MANUAL Page 14 of 20 EUROSTEAM SANITIZED FOR HEALTH REDEFINED ES2100 Controls There are two sets of operator controls the first set of three buttons are located on the front of the unit First button 1 heats the element in the pressure vessel Heating element button Second button 2 allows the steam to reach the hose Steam button Third button 3 is for water and steam combination Hot water button Green light illuminates when pressure is correct and machine is ready to use Yellow light illuminates when unit is low on water SS The second set of two buttons is located on the hose handle 1 First button A is for Medium steam pressure 2 Seco
25. r from the glass surface DEEP CLEANING Use small triangle on low to medium pressure Then use squeegee or a clean dry cotton towel to dry window WINDOW FRAME PAINTED WOOD Use 1 hole nozzle with detail brush depending on application 1 round 3 round or 3 triangle on medium pressure Place 1 towel around the brush and wipe frame PLASTICS Use 1 nozzle on medium to high pressure Hold the nozzle in one hand and a towel in the other hand Move the nozzle and towel at the same time in one direction blowing the dirt into the towel Hold the nozzle parallel to surface Move quickly Wipe with dry towel EUROSTEAM TRAINING MANUAL Page 11 of 20 EUROSTEAM US STEAM SANITIZED FOR HEALTH REDEFINED ALUMINUM Use brass brush directly on the surface to remove dirt and to polish Wipe with towel BLINDS CAUTION NOT RECOMMENDED FOR CLOTH BLINDS DO NOT USE EXCESSIVE HEAT ON VINYL BLINDS SLATS DUSTING Open blinds and use i hole nozzle on medium to high pressure to blow dust onto a wipe cloth or on the window and wipe clean DEEP CLEANING Close blinds with top of slats facing you Use triangle brush with one towel on low or medium pressure Wipe side to side from the top down To reach the whole slat spread the slats with the other hand while wiping Close the blinds from the opposite direction and clean from the bottom up Keep changing towels until clean If needed pre spray the blinds with VAPORMATE S
26. s a good bleach plus it softens hard water deposits and leaves a pleasant smell Especially effective in bathroom and kitchen areas AMMONIA Use a solution of vinegar salt and water or use baking soda and water GLASS CLEANER Use white vinegar OVEN CLEANER Scrub with a paste of baking soda salt and water GROUT CLEANER Scrub with a paste of baking soda salt and water RUST REMOVER A paste of lemon juice mixed with salt is a good rust remover METAL POLISH Stainless Steel Use baking soda or plain carbonated water Copper Soak in vinegar and salt solution Silver Soak 1 quart of warm water containing 1 tsp baking soda 1tsp salt and a piece of aluminum foil EUROSTEAM TRAINING MANUAL Page 5 of 20 EUROSTEAM US STEAM SANITIZED FOR HEALTH REDEFINED TOOL USE GUIDE TOOL APPLICATIONS 1 HOLE NOZZLE Use with Medium or High pressure where focused cleaning is needed Tile grout refrigerator dishwasher toilet bowls corners and crevices Spray area with Vapormate use on Medium or High heat 1 Hole Nozzle is also used with 1 inch brushes see 1 inch nylon and brass 1 INCH NYLON BRUSH Attach the 1 hole nozzle to the hose handle and then the brush to the base of toilets shower crevices and grout animal and birdcages Use Vapormate on surface as you clean Using med high steam move across surface to be cleaned making sure to cover all areas Let the heat do the work for you once the surface reaches the correct te
27. sure to cover all areas Let the heat do the ork for you once the surface reaches the correct temperature dirt will release and be surrounded by the moisture of the steam Wipe with towel as you clean EUROSTEAM TRAINING MANUAL Page 6 of 20 EUROSTEAM SANITIZED FOR HEALTH REDEFINED TOOL APPLICATIONS SMALL TRIANGULAR BRUSH Use to get into corners Attach the 3 hole nozzle to the hose handle and then the brush to the nozzle Set the steam dial to medium pressure doors Use Vapormate on surface as you clean Using med high steam move across surface to be cleaned making sure to cover all areas Let the heat do the work for you once the surface reaches the correct temperature dirt will release and be surrounded by the moisture of the steam Wipe with towel as you clean LARGE TRIANGULAR BRUSH Use this brush for cleaning hard to reach corners of floors under baseboards or wall tiles mattresses bed rails curtains upholstery carpets small windows stainless steel countertops cabinets kitchen bathroom walls door fronts and metal vertical blinds NOTE USE WITH TOWEL ON LOW PRESSURE SETTING TO KILL DUS MITES BED BUGS AND SANITIZE MATTRESSES AS WELL AS OTHER UPHOLSTERY ITEMS Use this brush without a clipped on towel for cleaning hard to reach corners of floors under baseboards or wall tiles then wipe immediately pets small windows i i vertical blinds Use with towel at low medium pressure change towel as Mattress Cleani
28. t set by heat the color can bleed from heat and moisture Man made carpet fibers melt at temperatures 300 and above The heat from the vapor system does not melt the fibers but it can change their shape at temperatures 185 F 250 F Use method described in SECTION IV to regulate the heat SPOT CARPET CLEANING Use single hole nozzle on high pressure Blow the steam parallel to the carpet surface working quickly in a back and forth motion Take a towel in your hand and blow the stain into the towel If any residue remains gently wipe area with towel Repeat until spot is gone Do not apply nozzle directly on to the spot this keeps the heat from exceeding 180 F 185 F which can chemically set protein based and food dye stains onto the fibers Once a stain is set it is hard to remove To remove stain treat it first see below and then follow up with the above procedure Lightly mist the stain with VAPORMATE if not available we offer the following suggestions PROTEIN STAIN Dab with towel dampened with a solution of 1 teaspoon white vinegar and 1 quart cold water FOOD DYE STAIN Wet stain with a solution of water and lemon juice or white vinegar WATER STAIN First wet the stain with carbonated water then use triangular brush with 1 towel on step 1 and wipe REOCCURRING STAIN If a stain comes up again and again it has a reservoir under the padding Before removing the stain yo
29. the System Customer is responsible for shipping charges incurred when shipping the System or a System component to an authorized repair center Customer is responsible for a 15 restocking fee plus replacement cost for any used parts Returned units must be shipped in original shipping container and unused before return credits will be considered by AKI LIMITATIONS EXCEPT AS SET FORTH HEREIN ENHQ MAKES NO WARRANTIES EXPRESSED OR IMPLIED AND DISCLAIM AND NEGATE ALL OTHER WARRANTIES INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND CONFORMITY TO MODELS OR SAMPLES SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES SO THESE LIMITATIONS MAY NOT APPLY TO YOU THE WARRANTY SET FORTH HEREIN GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN NO EVENT SHALL SELLER ENHQ BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU NO VARIATION OR EXCEPTIONS IN THE TERMS STATED HEREIN CAN BE MADE GOVERNING LAW JURISDICTION AND COSTS These limited warranties are incorporated into and are essential and material provisions of the terms and conditions of sale of seller products to you All disputes arising out OF OR related to the limited WARRANTY SET forth herein customer disputes shall be governed by the laws of the state of Texas the customer hereby consents to the
30. u have to dry it out first Press a drying agent such as talcum powder a mixture of cornstarch and cornmeal or clean unscented uncolored cat litter into the fibers do not rub Let sit for 20 minutes and then vacuum it out SURFACE STAIN If the stain is only on the surface of the carpet it can be removed by shooting the steam against the spot from the side 1 2 above surface Hold a towel on the other side to catch the residue This prevents driving the particles deeper into the fibers GUM Same technique as SURFACE STAIN except use paper towel instead of cotton towel If the gum melts too much let it cool off before trying again INDUSTRIAL APPLICATIONS MAINTENANCE Use rectangular brush 2 inches above carpet and pre steam on high pressure a 6x6 foot area The steam causes the dirt and soil particles to loosen their grip on the carpet fibers and opens up the fibers Then use the rectangular brush with 2 towels on medium pressure and go over pre steamed area with same movements as when you vacuum Change towels when dirty Repeat these steps if necessary Move on to next area DEEP CLEANING Pre steam the whole carpet and vacuum again Follow same steps as maintenance cleaning If needed pre spray carpet with VAPORMATE STAIN RESISTANT THE HEAT FROM THE STEAM CAN REMOVE THE CHEMICALS THAT MAKE THE CARPET STAIN RESISTANT AT TEMPERATURES BETWEEN 150 200 IF THE CARPET IS HEAVILY SOILED THE STAIN RESIST
31. water This eliminates the possibility of creating hard water stains while you are cleaning and prevents excessive build up of mineral deposits around the heating element in the tank If you use tap water get into the habit of flushing the tank every second week See water conditioning MAINTENANCE THE EXTERNAL STAINLESS STEEL CASING After each use it is recommended to wipe the EUROSTEAM external with a cleaning cloth and water to keep it clean of dirt and chemicals If buildups appear use the single hole nozzle and a wipe cloth to remove the dirt and grime In the case of heavy staining due to caustic chemical usage use a stainless steel polisher to restore the finish THE BOILER TANK RINSE THE MINERAL DEPOSITS FROM THE EUROSTEAM TANK AT LEAST ONCE A WEEK A good way of monitoring the mineral build up in the tank is by FLUSHING the system If the water residue from the hose is discolored on the towel or unit is heating up to slow Flush the tank e When unit is cold and unplugged place it over a sink open top cap unscrew drain plug on bottom of unit e Use tap water and rinse the tank until the water is clear e Replace drain plug hand tighten only XI CIRCUIT BREAKER ALWAYS TURN THE HEATING SWITCH TO OFF BEFORE YOU UNPLUG IT If possible plug the unit into an outlet isolated from other equipment or turn the other equipment off while using the EJUROSTEAM the combined effect of other equipment the EUROSTEAM together ma
32. way to the right press the trigger to remove water residue from the hose into towel for about 5 to 10 seconds Wait until green MAXIUM PRESSURE lights again before starting to clean Now the system is ready for any cleaning task VERY IMPORTANT Always release the cold pressure out of the tank before heating up a unit You do this automatically when you fill the unit with water If you don t fill up open the top cap and release the pressure and then turn the heating and main switch on The boiler is well insulated and will keep most of the heat for up to 2 hours after unplugging it II HOW TO REFILL A HOT EUROSTEAM Your Eurosteam is low on water when one of the following happens a Yellow light comes on b The pressure drops fast and pressure gauge stays low TO REFILL c Turn the HEATING SWITCH 1 to off leave steam switch 2 on and use the remaining steam in the unit by continuing to clean until pressure gauge drops to 0 d Turn the POWER SWITCH off and unplug the unit e Place a towel over the top cap and slowly open it to release the remaining steam f Remove the cap and refill with clean water for quicker heat up time fill with clean hot water using the filler bottle with spill proof cap or funnel Hand tighten the top cap Plug the unit in turn the HEATING ELEMENT switch on III PRESSURE Stay in the habit of using MEDIUM PRESSURE ES1900 amp ES2100 left switch up right switch down ES4500 top left knob in t
33. y cause a circuit breaker to trip SURFACE CLEANING KITCHEN COUNTERTOPS Method 1 Use 3 inch round with 3 hole nozzle in slow back and forth movements to cover area being cleaned Wipe with clean cotton towel Method 2 Diaper large triangle brush heat towel with high pressure 3 to 5 seconds Turn pressure to low and clean surface using back and forth movements OVEN MAKE SURE SURFACE IS COOL TO THE TOUCH BEFORE CLEANING Begin by misting with EUROSTEAM VAPORMATE Press stainless steel scrubbing pad onto 3 inch round brush using medium pressure Cover entire surface slowly NOTE Always move slowly to allow heat to break away residue that has adhered to the surface being cleaned DO NOT SCRUB HEAVILY AS THIS MAY DAMAGE ENAMEL DISHWASHER Using single hole nozzle clean out corners and edges For light scrubbing add 1 inch round nylon brush For larger surfaces use 3 inch round or 3 inch triangle with 3 hole nozzle using back and forth movements over area being cleaned Wipe clean with cotton towel REFRIGERATOR FREEZER clean out all food and trays EUROSTEAM TRAINING MANUAL Page 8 of 20 EUROSTEAM SANITIZED FOR HEALTH REDEFINED Mist area with EUROSTEAM VAPORMATE Clean door molding with single hole nozzle Add 1 inch round nylon for light scrubbing Starting from top of refrigerator use a 3 hole nozzle with 3 inch round or 3 inch triangle Clean all areas Wipe cleaned area with cotton towel as you go BATHROOM FAUCET AND
Download Pdf Manuals
Related Search