OPERATING MANUAL
Contents
1. OIL TUBE NOZZLE ELECTRODE CLAMP Py NOZZLE ADAPTER SPINNER ASSEMBLY RETENTION HEAD AIRTUBE NOZZLE ASSEMBLY FIGURE 2A INSERTING REMOVING NOZZLE HEAD ASSEMBLY User s Manual Clean Burn Radiant Heater Reinstall nozzle check electrodes WARNING Inspect the nozzle adapter before replacing the nozzle If the threads have been damaged or shows score marks replace the nozzle line adapter assembly Replace the retention head by replacing screw removed during disassembly When reassembling align weep hole perpendicular to the bottom of heater so when unit is fully assembled weep hole faces the ground When reassembling spinner assembly the Spinner Clamp should be firmly against the nozzle adapter shoulder Tighten Spinner Clamp screw to secure spinner clamp position Check the electrode settings Position the electrodes as shown in Figure 2A These settings are critical in ensuring a reliable ignition Once the electrodes are set check all clamps to ensure they are securely tightened Figure CAREFULLY SUPPORT THE NOZZLE ADAPTER WHEN REMOVING OR INSTALLING NOZZLE To replace the nozzle assembly reverse the previous sequence See Figure 2A Use care when tightening the oil line fitting to oil tube extension Tighten securely but do not cross thread or over tighten SEE FIGURE 2A 3 3 User s Manual Clean Burn Radiant Heater Air Band Adjustment Air band is pre set from factory an2. OLOHd WNIWYAL woud Nd TOYLNOD INVA YOLINDI 1 10N ova on 0 1318 2 ILIHM HLV3HS ILIHM YOLOW HaMOTE OL 1NN FAIM 5 OL 68LEE Nd YOLIN I 9S767 FIGURE A1 COMPLETE WIRING SCHEMATIC User s Manual Clean Burn Radiant Heater Troubleshooting Heater Fails to Start Solution Cad Cell Dirty or Defective Clean or Replace Erratic Flame Solution NOTES CLEAN 4 BURN ENERGY SYSTEMS CLEAN BURN LLC 4109 Capital Circle Janesville Wisconsin 53546 1 800 331 0183 www cleanburn com CLEAN BURN is a registered trademark of CLEAN BURN LLC
3. THIS MANUAL IMPORTANT Review the list of general safety precautions provided in your Radiant Heater Operator s Manual These precautions must be heeded to ensure proper safe operation 1 1 User s Manual Clean Burn Radiant Heater SPECIFICATIONS amp CLEARANCES Model Sunfire SF 100 Manufacturer Clean Burn LLC Janesville WI Listed Fuel NO 2 Fuel Oil Input Rating W No 2 oil GPH High 1 10 Low 0 97 Minimum Installation Clearance to Combustible Surfaces Front 72 Right Side 24 Left Side 24 Above N A Back N A Below 0 to Non Combustible Flooring The designated clearances are the minimum required to avoid overheating Additional clearances may be needed for accessibility Electrical Rating 120V 2A 60HZ Fuel Tank Capacity 19 1 US G Weight 181 LBS Empty 307 LBS Full Air Setting 1 00 Nozzle 85 60A 1 2 User s Manual Clean Burn Radiant Heater WARRANTY INFORMATION Clean Burn warrants that it s Radiant Heaters and component parts will be free from defects in material and workmanship for a period of 24 months from date of purchase when properly installed operated and maintained in accordance with the installation and maintenance instructions safety guides and labels contained with each unit If any component proves defective in either material or workmanship during the limited warranty period Clean Burn at its option may repair the defective part or equipment or replace the equipment o
4. after running out of fuel it will be necessary to prime the pump With power switch off remove black outer burner hood Loosen the bleeder valve on pump with a 3 8 wrench Prepare a small container to catch any oil coming out of the bleeder valve and then start the unit letting the oil run free of any air bubbles This may require pushing the reset button more than once as the primary control will shut down if no flame is sensed within 15 seconds Once the burner priming process is complete replace the burner hood WARNING DO NOT OPERATE RADIANT HEATER WITHOUT THE BURNER HOOD SECURELY ATTACHED NOTE When in operation if the heater runs out of fuel you will have to bleed the pump NOTE After the first hour of operation the unit will require a re torque of the screws around the outer ring on the front of the heater to 23 10 65 2 1 User s Manual Clean Burn Radiant Heater HOOD CONTROL DETAIL ZOOM ON OFF HIGH LOW INDICATOR INDICATOR LIGHT LIGHT RESET SWITCH RESET ON OFF HIGH LOW TOGGLE TOGGLE SWITCH SWITCH 56 TOP OF HOOD FIGURE 1A RADIANT HEATER HOOD CONTROLS OVERVIEW 2 2 User s Manual Clean Burn Radiant Heater SECTION 3 MAINTENANCE REMOVING INSTALLING HEAD ASSEMBLY WARNING Only attempt to handle burner components after the unit has fully cooled down Components can be hot and could cause severe personal injury NOTE You will need to remove the burner assembly for inspection of the
5. handled or refilled and no maintenance should be performed on it e Smoke that is produced from the first combustion is due to the evaporation of organic materials ceramic present in the combustion tank and anti corrosion oil present on the surface of the burner After a few minutes this will stop The operating temperature is 20 F to 80 F 1 5 User s Manual Clean Burn Radiant Heater 1 6 User s Manual Clean Burn Radiant Heater SECTION 2 OPERATION Following is an outline of the Radiant Heater basic operation process RADIANT HEATER OPERATION Keep unit a level non combustible surface at all times If the unit 15 on sitting on a 25 angle or more the tip switch will prevent the heater from starting Fill tank with Diesel or 2 Fuel Oil Plug into a grounded outlet or extension cord Switch to high fire Turn power switch ON The blower will come on and run for 15 seconds prior to lighting pre purge Se the heater is running you will have green light for power and an amber light for high fire When the unit is switched to low fire the amber light is off 7 When shutting down the heater turn power switch to off Allow the burner to complete the post purge cycle 300 seconds before disconnecting power Failure to complete the post purge cycle may result in excessive heat damaging the unit as well as a longer pre purge cycle on the next start On initial start up or
6. motor to blower housing a Slide the motor out and rotate to remove and access blower wheel b Use a brush and vacuum to clean each blade and the blower housing interior Replace motor wheel in blower housing and secure with the two bolts Push wire slack back into junction box Replacing blower motor or wheel 1 If either the blower wheel or motor must be replaced remove the two bolts securing the motor to housing Disconnect the motor wires in the burner junction box Loosen the Allen screw securing the blower to the motor shaft and remove the wheel When assembling the replacement assembly slide the wheel onto the motor shaft and use feeler gauges to set a space of 3 64 inch between the blower wheel and the motor face 5 Replace the motor wheel assembly in the housing wire the motor leads and secure the motor with the two bolts 3 4 User s Manual Clean Burn Radiant Heater Motor maintenance The PSC motor is constructed with permanently lubricated bearings and requires no oiling CAUTION Any time you replace a component or disassemble any part of the burner for service maintenance perform a complete operational test after reassembly to verify the burner operates correctly Failure to verify operation could result in severe personal injury death or substantial property damage WARNING CHECKING IGNITOR A Never test an ignitor by placing a screwdriver or other metallic object across the high voltage clips Check the i
7. nozzle and electrodes To remove the burner assembly 1 2 3 Remove the rear hood screw and set aside for re installation Remove the four bolts securing the burner assembly to the outer cone of the heater Pull gently to remove the burner assembly from the outer cone of the heater taking care not to disconnect any wiring If nozzles or electrodes are in need of replacement gently prop the burner assembly on the heater tank to allow access to nozzle assembly again taking care not to disconnect any wiring To remove the nozzle assembly 1 Loosen and then rotate the two screw clamps securing the ignitor plate in place Swing the ignitor plate open Unscrew the oil line fitting and thumb nut at the burner housing Figure 2B Remove the retention head Figure 2A Gently push the nozzle assembly through the front of the burner Handle the nozzle assembly with care to avoid bending moving the electrodes or damaging the electrode ceramic insulators and spinner assembly Inspect the gasket on the bottom of the ignitor cover The gasket prevents air from escaping from the housing Replace the gasket if not in good condition Inspect the ignitor contact clips Clean or replace if necessary to ensure reliable contact with the electrodes FIGURE 2B OIL LINE FITTING 3 1 User s Manual Clean Burn Radiant Heater 1 8 to 5 32 FLUSH TO 1 16 7 7 0 1 5 SPINNER CLAMP ELECTRODE
8. operate your radiant heater safely and correctly USE ONLY NO 2 FUEL OIL DIESEL To diminish the risk of fire or explosion Never use gasoline crankcase drainings naphtha paint thinners alcohol or other highly flammable materials FILLING THE TANK a The person filling the tank should be qualified and completely familiar with the factory instructions for the operation of the radiant heater b Use only the type of fuel expressly specified on the identification plate located on the Radiant Heater c Before filling the tank extinguish all of the flames including the radiant heater and wait for the radiant heater to cool down d While filling the tank inspect all of the fuel lines and their junctions to check for fuel losses Any losses must be repaired before starting the radiant heater again e All of the fuel tanks should be located a minimum safety distance from the heater like current government regulation as well as oxyhydrogen blowpipe torches welding equipment and similar ignition sources with the exception of the fuel tank incorporated in the Radiant Heater f The fuel should be stored in areas where the flooring will not soak up any fuel spills or any drips of fuel line the flame underneath that could cause a fire g fuel storage must be stored in compliance with the current regulations 1 4 User s Manual Clean Burn Radiant Heater SAFETY GUIDELINES CONT GENERAL OPERATION GUIDELINES e Neve
9. CLEAN BURN ENERGY SYSTEMS OPERATING MANUAL CLEAN BURN MODEL SF 100 SUNFIRE 100 PORTABLE RADIANT HEATER PUBLICATION DATE 11 02 15 Rev 2 MANUAL PART 43219 Important Read this entire manual carefully before operating or performing any maintenance on this Radiant Heater Misuse may result in serious of fatal injuries due to burns fire explosion electrical shock or asphyxiation from carbon monoxide TABLE OF CONTENTS NOTE A Special Bulletin which appears just after the Table of Contents has been added to your manual to highlight important information about the adjustment and operation of your Radiant Heater Be sure to read this sheet before beginning any procedures in this manual SECTION 1 INTRODUCTION siscsssiscsssccciscsscsseessessessccsscessetscesscessestsessessensseassnsssesseessessscessesscessesssesss 1 1 Guide to this Manual amp Safety Notifications 1 1 Specifications and Clearances 1 2 Warranty Information 1 3 Special Safety Bulletin 1 4 SECTION 2 OPERATION essessesssvsscnssssscccssseseessessseasonssesssvecsestsessonsdeasenstensesetsessecsssessessesscensesssnsstseesesss 2 1 amp 2 1 Hood Controls Overview 2 2 SECTION 3 MAINTAINING THE RADIANT HEATER ccsssscccssseccccsssccecsssscccsssscces
10. d in most cases will only require adjustment in high altitude locations 1 To adjust air band loosen screw and rotate air band open or closed until desired flame is attained 2 Re tighten Screw to re secure Air Band in newly adjusted position Burner Pump Pressure Adjustment Burner pump pressure is factory set and in most cases should not be changed If adjustment is required please contact your distributor for assistance Annual Maintenance and Service Procedures NOTE Maintaining and Cleaning your heater at the end of each heating season is important to prolong the life of your radiant heater and keep it operating in peak condition WARNING Turn off power to appliance when servicing burner Failure to comply could result in severe personal injury death or substantial property damage Replace filter element after 200 hours approximately 5 tanks of fuel Clean the blower wheel The blower wheel accumulates dust and debris from normal operation You will need to clean the wheel blades periodically to prevent reduction in airflow 1 Inspect the blower wheel by removing the blower wheel access cover a remove the cover open the ignitor plate and loosen the blower wheel access cover screw about three turns b Inspect the blower wheel to see if it needs to be cleaned Dirt and lint on the wheel reduce air flow and must be removed if the burner is to operate correctly 2 clean blades remove the two bolts securing the
11. gnitors only by observing spark at appliance ignition electrodes with fuel supply OFF Using any other method could cause ignitor damage and severe personal injury Carefully energize ignitor and check for spark arcing at the high voltage terminals If spark jumps the gap ignitor is good Tank maintenance If it becomes necessary to drain the fuel tank there is a drain plug located on the bottom of the tank WARNING CERAMIC FIBER MATERIALS The appliance may contain ceramic fiber and or fiberglass materials Ceramic fiber materials such as chamber liners may contain carcinogenic particles chrystobalites after exposure to heat Airborne particles from fiberglass or ceramic fiber components have been listed as potentially carcinogenic by the State of California Take the following precautions when removing replacing and handling these items Avoid breathing dust and avoid contact with skin or eyes Wear long sleeved loose fitting clothing gloves and eye protection Use a NIOSH N95 certified respirator This respirator meets requirements for protection from chrystobalites Actual job requirements or NIOSH regulations may require other or additional protection For information refer to the NIOSH website http www cdc gov niosh homepage html Ceramic fiber removal To prevent airborne dust thoroughly wet ceramic fiber with water before handling Place ceramic fiber materials in a plastic bag and seal to dispose Avoid blowing tearing
12. l find the step by step procedures easy to follow and understand Should questions arise please contact your Clean Burn dealer before starting any of the procedures in this manual Please read all sections in this manual carefully including the following safety information before beginning any installation procedures doing so ensures your safety and the optimal performance of your Clean Burn Radiant Heater FOR YOUR SAFETY For your safety Clean Burn documentation may contain W ARN IN G the following types of safety statements listed here in order of increasing intensity e NOTE A clarification of previous information or additional pertinent information e ATTENTION A safety statement indicating that potential equipment damage may occur if instructions are not followed CAUTION A safety statement A that reminds of safety practices or directs attention to unsafe practices which could result in personal injury if proper precautions are not taken WARNING A strong safety statement indicating that a hazard exists which can result in injury or death if proper STOP precautions are not taken gt A DANGER The utmost levels of YOUR SAFETY IS AT STAKE safety must be observed an extreme hazard DO NOT INSTALL OPERATE OR exists which would result in high probability MAINTAIN THIS EQUIPMENT of death or irreparable serious personal WITHOUT FIRST READING injury if proper precautions are not taken AND UNDERSTANDING
13. ome states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you TRADEMARKS The Clean Burn logo is a trademark of Clean Burn LLC other brand or product names mentioned the registered trademarks or trademarks of their respective owners COPYRIGHT Copyright 2015 Clean Burn LLC All rights reserved No part of this publication may be reproduced or distributed without the prior written permission of Clean Burn LLC Subject to change without notice 1 3 User s Manual Clean Burn Radiant Heater SPECIAL SAFETY BULLETIN IMPORTANT INFORMATION CONCERNING SAFETY GUIDELINES SAFETY GUIDELINES DANGER Carbon monoxide asphyxiation can be fatal CARBON MONOXIDE ASPHYXIATION The first symptoms of carbon monoxide asphyxiation are similar to that of the flu headaches dizziness and or nausea These symptoms could be caused by the malfunction of the Radiant Heater In this case go outside immediately Have the Radiant Heater repaired Then you may start it again Some people are more affected by the effects of carbon monoxide than others especially pregnant women those who suffer from heart or lung disease or people with anemia also those who have consumed alcoholic beverages and those who are at high altitudes Be sure to read and understand all of the warnings Save this manual for future reference it will provide you with instructions to
14. r relevant parts Proof of purchase and warranty qualification must be established at time of all returns and exchanges BILL OF SALE A copy of the bill of sale must be provided at time of return CLAIM PROCEDURE All claims are to be submitted to your Clean Burn Distributor This limited warranty does not apply to heater component or replacement part damage resulting from incorrect installation misuse abuse accident act of God neglect mishandling contaminated fuel modification incorrect environments or wear from ordinary use The warranty set forth above is the exclusive warranty provided by Clean Burn and all other warranties including any implied warranties or merchantability or fitness for a particular purpose are expressly disclaimed In the event any implied warranty is not hereby effectively disclaimed due to operation of law such implied warranty is limited in duration to the duration of the applicable warranty stated above The remedies set forth above are the sole and exclusive remedies available hereunder Clean Burn will not be liable for any incidental or consequential damages directly or indirectly related to the sales handling or use of the equipment and in any event Clean Burn in connection with the equipment including for claims based on negligence or strict liability is limited to the purchase price Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you S
15. r use the Radiant Heater in rooms where aerosol cans gasoline and paint thinner or other highly flammable materials are located e While the heater is in use follow all of the local codes e Heaters used close to large pieces of fabric curtains or other similar materials must be situated at a safe distance from those objects e For the Ist hour of operation run outside due to gases given off by new insulation When moving push don t pull e Use only well ventilated areas e Supply the Radiant Heater with the proper voltage as specified on the identification plate e Use only extension cords with three wires correctly connected to a grounded plug The minimum safety distance is the distance required by local code e Place the Radiant Heater in a position so that when it is hot or in use it will be on a stable and level surface so that you avoid starting a fire e When you move or store the Radiant Heater maintain it in a level position in order to avoid fuel loss e Keep children and animals away from the Radiant Heater e Disconnect the Radiant Heater when it is not in use When it is controlled by another device like a thermostat or a timer the heater could turn itself on at any time e Never place the Radiant Heater in unoccupied rooms e Never use for this radiant heater for a residential application e Never block vents e When the heater is hot and connected to the power supply it should never be moved
16. sawing or spraying fiberglass or ceramic fiber materials If such operations are necessary wear extra protection to prevent breathing dust Wash work clothes separately from other laundry Rinse clothes washer thoroughly afterwards to prevent contamination of other clothing NIOSH First aid procedures Eye exposure irrigate immediately Breathing fresh air 3 5 User s Manual Clean Burn Radiant Heater 3 6 19 2 NOILaNNOD 01 918 0 10N N3349 t Heater lan Clean Burn Radi User s Manual APPENDIX A ials Reference Materi 1ca Techn wanung 01318 xog NOILINNAL 5 1 MOTTA TETAS LAN FAIM NOILIaNNOD LAN HDLIMS YSAOD 1139 OLOHd NIM OL 4VLSOWYSHL NOILVYNDIANOD LVLSOWYSHL TWNOILdO HOLIMS ALN NOILI3NNOD LAN INYA 1 gionaiios 1301A HM INVA 1 5 LAN ion LAN 135 TIID
17. sssecees 3 1 Removing and Installing Head Assembly 3 1 Air Band 3 4 Burner Adjustment 3 4 Annual Maintenance and Service 3 4 Cleaning the Blower 3 4 Replacing the Blower Motor or Wheel 3 4 Motor Marnitenanice tl nea aa 3 5 Tank Maintemarice 3 5 Ceramic Fiber Removal 3 5 NIOSH First Aid 3 5 APPENDIX cctssisecscsasccccsssseccsnssecccnasseccnassecscassecccnnssencisssenscunsenscusssenscessenscunssescuassenccnasentenasseecnassecccnassencs 4 1 Complete Radiant Heater Wiring 1 1 Troubleshooting 2 User s Manual Clean Burn Radiant Heater SECTION 1 INTRODUCTION Guide to this Manual IMPORTANT This manual provides all the instructions necessary to safely use the Clean Burn Sunfire Radiant Heater Please refer to this manual for instructions on operating and maintaining your Sunfire Radiant Heater Consult the Table of Contents for a detailed list of topics covered in this manual You l
Download Pdf Manuals
Related Search