User`s Manual
Contents
1. Mid Span Type B Hardware Specification 10 100Mbps Switch AccHitercure Store and Forward Switch Throughput 148810pps 64Bytes 7 840 s Maximum Back pressure for Half Duplex IEEE 802 3x Pause Frame for Full Duplex e 1 x PoE IN Green e 1 x LAN Data Green e 1 x PoE OUT Green Protection ESP Ethernet 6KV TBD Surge EFT for power 6KV TBD Dimension W x D x H 94 x 70 x 26 mm 215g Power IEEE 802 3af compliant with voltage Requirement within 44V 56V DC Power 2 Watts system maximum Metal Wall Mountable Cable TIA EIA 568 Category 5 5e cable LED Indicators Standards Conformance Reguiation cc part 15 Class A CE Compliance IEEE 802 3 10Base T Ethernet IEEE 802 3u 10 100Base TX Fast Ethernet Standard IEEE 802 3af Power over Ethernet PSE Compliance Mid Span IEEE 802 3af Power over Ethernet PD Mid Span IEEE 802 3x Flow Control Temperature 0 50 Degree C Relative Humidity 0 95 non condensing Operating Temperature 40 85 Degree C Relative Humidity 5 95 non condensing Storage Hardware Description 2 1 Product Outlook PLANGI UJIRA Power over Ethernet Extender 10 100Base TX Li i OO O AS e eG e4 2 2 Ports Connection Connect the PoE IN port from following 802 3af PSE device through a CAT 5e 6 UTP cable e PoE Injector e PoE Injector Hub e PoE Ethernet Switch e Previous POE E101 Connect the P2. remote PoE powered device to the OUT port of next or third POE E101 300 meters 200 meters 100 meters O meters 11W 13W 15W POE E101 POE E101 100 meters 100 meters 100 meters POE Access Pomt PoE Extender PoE Extender PoE IP Camera POE E101 100 meters 100 meters PoE Ethernet Switch PoE Extender Injector Hub PoE Splitter POE E101 100 meters 100 meters PoE Extender Power Line AC Power Line DC 100Base TX UTP Non PoE IP Camera 100Base TX UTP with PoE 1 Per POE E101 will take 2 watts maximum for the system itself please check the total power consumption of your 802 3af PD and the POE E101 before you make the daisy chain connection If the overall power consumption is overloaded the local PSE could shutdown the whole power system Per POE E101 cable segment is limited in 100 meters CAT 5e 6 UTP wire from its IN OUT port to the other data end use of any other non standard cable or over distance could results in unstable connection PLANET Technology Corp 2350 AF0230 001 WwwWw PLANET com tw 3 3 5 Optional DIN Rail mounting There are two DIN Rail holes on the left side of the POE E101 that allows the converter can be easily installed with DIN Rail mounting The PLANET optional DIN Rail mounting Kit RKE DIN can be order separately When need to replace the wall mount application with DIN Rail application on the POE E101 please refer to following figures to screw the DIN
3. POE E101 injects power to the PDs without affecting the data transmission performance It offers a cost effective and quick solution to extend power and data an additional 100m The POE E101 can be installed with third party device if the device complied with IEEE 802 3af standard 3 2 Connect POE E101 to the Power Source Equipment PSE There are 2 RJ 45 ports in the PoE Extender of which the IN port functions as PoE Data and Power Input and the OUT port on the other side functions as PoE Data and Power output Step 1 Connect a standard CAT 5e 6 UTP cable from Power Source Equipment PSE such as PoE Switch PoE Injector hub and single port PoE injector to the IN port of POE E101 The PSE delivers both Ethernet Data and PoE power over UTP cable to the POE E101 and the PoE IN LED will be steady on 1 The PoE IN LED turn on steady green means POE E101 is being powered successfully with PoE class 0 2 If POE IN LED does not turn on please check the remote PSE or the cable with a PC or a network device to see if the cable is correct Or with an 802 3af device such as the target PD to check the power injection is correct either 3 3 Connect POE E101 to the Powered Device PD Step 3 Connect the additional CAT 5e 6 cable that will be used to connect to the remote Powered Device PD to the OUT port of POE E101 Step 4 The OUT port is also the power injectors
4. which transmit DC Voltage to the CAT 5e 6 cable and _ transfer data and power simultaneously between the PSE and PD Once POE E101 detects the existence of an IEEE 802 3af device the PoE OUT LED indicator will be steady ON to shows it is providing power POE E101 Data BA Power Data P Power PoE 100 meters 100 meters PoE IP Camera PoE Extender e _ ____ _ 200 meters Power Line AC Power Line DC 100Base TX UTP 1 100Base TX UTP with PoE 1 If the connected device is not fully complying with IEEE 802 3af standard or in line power device the PoE OUT LED indicator of POE E101 will not be steady on 2 According to IEEE 802 3af standard the POE E101 will not inject power to the cable if not connecting to a standard IEEE 802 3af device 3 4 Multiple PoE Extender Installation The POE E101 PoE Extender supports multiple units daisy chain installation They can be employed in series for even longer distances based on remote PoE IP Camera or PoE Wireless Access Point power requirement Step 1 Connect the additional CAT 5e 6 cable from the OUT port of the first POE 101 the other end of the UTP cable be used to connect to the IN port of remote next POE E101 The PoE OUT LED indicator of the first POE 101 will be steady to shows it is providing power to next PoE Extender The PoE IN LED on the next POE 101 will steady on Connect the additional CAT 5e 6 cable to the
5. Introduction 1 1 Packet Contents Thank you for purchasing PLANET POE E101 IEEE 802 3af Power over Ethernet Extender your Power over Ethernet Extender package shall contains following contents Check the contents of your package for following parts Power over Ethernet Extender x 1 User s Manual x 1 If any of these pieces are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 Key Features Complies with IEEE 802 3af Power over Ethernet Extends the range of PoE an additional 100 meters 328ft Forwards both Ethernet data and PoE power to remote device Auto detect and protect of PoE equipment from being damaged by incorrect installation Multiple units daisy chain installation support No external power cable installation required Compact size Wall mountable design Plug and Play installation 1 3 Technical Specification Interfaces 1 x 10 100Base TX Ethernet with IEEE 802 3af PoE Data DC in Auto MDI MDI X Auto negotiation RJ 45 connector 1 x 10 100Base TX Ethernet with IEEE 802 3af PoE Data DC out Auto MDI MDI X Auto negotiation RJ 45 connector Power over Ethernet PoE Standard IEEE 802 3af Power over Ethernet PoE Power Supply Type PoE Power 48V DC 270mA Max 13 Watts Output Power Pin
6. Rail on the converter To hang the POE E101 follow the below steps Step 1 screw the DIN Rail on the POE E101 M a lt ay lt A x lt PLANET Networking amp Communication User s Manual PoE Extender IEEE 802 3af Power over Ethernet Extender Step 2 Lightly press the button of DIN Rail into the track You must use the screws supplied with the mounting brackets Damage caused to the parts by using incorrect screws would invalidate your warranty
7. oE OUT port to following 802 3af PD device through a CAT 5e 6 UTP cable e PoE IP Camera OUT Port POE VoIP Phone PoE Wireless AP PoE Splitter Next POE E101 2 3 LED Definition LED Color Function Green Lights to indicate the port is providing 48V DC in line power Lights to indicate the port is link up LNK Blink indicate that the extender is Green i a ACT actively sending or receiving data over IN port PoE Been Lights to indicate the port is OUT providing 48V DC in line power Hardware Installation This product provides two different running speeds 10Mbps 100Mbps in the same device and automatically distinguishes the speed of incoming connection This section describes the hardware features of POE E101 Before connecting any network device to the POE E101 read this chapter carefully 3 1 Before Installation Before your installation it is recommended to check your network environment If there is any far away IEEE 802 3af devices need to power on the POE E101 can provide you a way to supply power for this Ethernet device conveniently and easily The POE E101 is installed between the PSE Power Source Equipment and the PD Powered Device it is powered by PSE and forwards the Ethernet data and remaining POE power to the PD The POE E101 doesn t require an external power supply and it can be installed easily just plug and play that means the operator does not need to configure the POE E101 The
Download Pdf Manuals
Related Search