WL-090 LED Dental Curing Light
Contents
1. TURBO E oe y GO OR Approx 2400 mW cm 10 If result of intensity test in STANDARD mode is under 700 mW cm the output is too low please contact with your dealer we will check your light Clean and disinfection The plastic of the handpiece cradle and filter may be cleaned with a wet cloth while the optical light guide rod may be cleaned with alcohol or put it in autoclave for disinfection Suggestion is to use autoclave 134 C 75 psi for maximum result The disinfection time at 134 C should be 5 minutes A disposable curing sleeve available from your dealer may be used as protection over the optical light guide rod without loss of light intensity The applicant will or have validate the sterilization procedure according to ISO 17665 1 LEDEX WL 090 LED Dental Curing Light EN Warranty DENTMATE TECHNOLOGY Co Ltd warrants the product to be free of manufacturing defects for a period of 1 year from date of purchase this being deemed the date of the invoice It will repair or replace at its own discretion all equipment failures due to manufacturing defects The following are however expressly excluded from the warranty 1 Damage and or failure of the equipment caused by falling and or jolting during transportation after purchase and or during normal use 2 Damage and or failure of the equipment caused by natural disasters such as but not limited to earthquakes floods lightning pollution incorrect electrical vo2. cycle has expired after approx 30 months The LEDEX WL 090 is the specialized equipment for dental department and it should be operated by specialist only in the dental clinic To avoid to damage the eyes please do not point the beam of the light toward the eyes LEDEX WL 090 PP LED Dental Curing Light EN Do not exceed recommended irradiation time and light intensity for an application as tooth overheating may result Please do not continuously irradiate on any specific area for a long time because it may cause the head of the device to be too hot If so we strongly suggest you to move it away for a while Remember to properly adjust the time of light irradiation according to different light intensity Li ion It is danger of explosion if battery is incorrectly replaced To reduce risk of fire or burns do not disassemble crush puncture short external contacts expose to temperature above 60 C 140 F or dispose of in fire or water Replace only with specified batteries Recycle or dispose of used batteries according to the local regulations or reference guide supplied with your product LEDEX WL 090 LED Dental Curing Light EN Indication for use LEDEX WL 090 is a visible curing unit programmed for polymerization of dental light cured materials by dental professionals Conditions for use 10 C 40 C 30 75 relative humidity 500hPa 1060hPa atmospheric pressure Conditions for storage and transpo
3. of items 01 LEDEX WL 090 handpiece Eech 02 Battery Including in handpiece 3 7V 2500mAh EE E EAE 1 03 Cradle aal 04 Power supply Input AC100 240 V 50 60Hz output DC5V 1 2A Y 1 05 Optical fiber light guide rod 11 gt 8 mm 1 d OUT FR EFYRNWY saben cab lee eee RAIN RIN FRON NEFYN EN A NEU FYNO 1 OZ Anti glare shield iei ni ENEE YRU OLA NA ADDO ikea SENNENG 2 08 Light guide sleeves Y eee cee neiaa 20 09 Curing light sleeves LLY eee cence eee ee eee DRYLL LYFR Y FE nuu 10 10 Users manual eu GE GG ANNE NN YNO GN DE wn fog d ebe 1 LEDEX WL 090 LED Dental Curing Light EN Charging the Battery The battery is not fully charged at shipment Before use please charge the battery charging time is about 2 hours 1 Connect the power supply to AC100 240V electronic socket and plug in connector to cradle Put hand piece into cradle to charge battery 2 When the battery is in low status the display of handpiece will glow showing battery low sign Refer to figure 1 3 When the battery is fully charging the display of handpiece will glow showing battery full sign Refer to figure 2 4 When the battery is charging the display of handpiece will glow showing battery charge sign Refer to figure 3 Figure 1 Figure 2 Figure 3 LEDEX WL 090 LED Dental Curing Light EN Turn on handpiece Push the on off button to turn on the LEDEX WL 090 handpiece Output Interrupt the light When t
4. D20 OEF UK TEL 44 0 1535 652 750 FAX 44 0 1535 652 751 WEBSITE www topdental org EMAIL sales topdental co uk DENTMATE TECHNOLOGY CO LTD 8F No 8 11 Sec 1 Zhongxing Road Wugu District New Taipei City 24872 Taiwan TEL 886 2 8976 9226 FAX 4886 2 8976 9236 WEBSITE www dentmate com tw EMAIL info dentmate com tw 2014 01
5. LEDEX wL 090 LED Dental Curing Light I hr e2 V User s manual CE A lot of research amp development has gone into the manufacturing of this EN product and we sincerely hope that it will give you many years of trouble free use Please read and understand all the instructions before using this equipment and save this manual for your reference gt PGP gt gt LED Dental Curing Light EN This icon marks warnings information that should be read before using your product to prevent possible injury Use only the authorized parts provided for the purpose to maintain compliance with product regulations Do not disassemble Touching the product s internal parts could result in injury In the event of a malfunction the product should be repaired only by a gualified technician When inserting the battery do not attempt to insert it upside down Do not short or disassemble the battery Do not expose the battery to flame or to excessive heat Do not immerse in or expose to water For as long a life cycle of battery as possible please return the hand piece to the cradle as often as possible and do not store battery for longer than 6 months In order to avoid irrevocable deep discharge if the battery is not used a new battery is best purchased only once the old battery needs to be replaced Since the battery is a consumable it has to be replaced if the performance drops considerably or after its typical life
6. he status of handpiece is turning on push the ZO on off button again to output the light During the exposure time the specialist can push on off button to interrupt the light Then the system will generate one beep and reset the time automatically Change the mode format Push the M mode button the mode can be changed LOW gt RAMP gt STANDARD gt HIGH gt FAST ORTHO gt TURBO gt LOW Change the timer format Push the T timer button the time can be changed LOW mode 10220230240210 gt 20 gt 30 RAMP mode 5 gt 10215 gt 220225 gt 30235 gt 24025 gt 10 gt 15 STANDARD mode 531031532032533033534035310315 HIGH mode 2343638310323436 FAST ORTHO mode 334353334 TURBO mode 2333435323334 LEDEX WL 090 LED Dental Curing Light EN Recommend for use LOW mode Ideal for curing bonding material that is between tooth and composite resin RAMP mode Ideal for curing the wide area of composite resin it can avoid shrinkage STANDARD mode It is a stable output ideal for most cases HIGH mode Ideal for orthodontic or pediatric dentistry it can save time FAST ORTHO mode Ideal for orthodontic it is easy to bond materials and saving time TURBO mode Ideal for non vital tooth or such as dental cement porcelain veneer fiber post in endodontic fields LEDEX WL 090 LED Dental Curing Light EN Auto sleep designed LEDEX WL 090 will sleeps automatically if
7. ltage and voltage spikes Do not attempt to open the hand piece as doing so will invalidate the warranty LEDEX WL 090 LED Dental Curing Light EN Specifications Dental Curing Light Medical equipment Device Name LEDEX Model Number WL 090 Power supply Input AC100 240V 50 60Hz Output DC 5V 1 2A Battery 3 7V 2500mAh type Lithium ion Light source 10W Dental blue LED The range of wavelength 440 to 480 nm Radiant intensity 600 to 2400 mW cm Hand piece size 38 mm max x L190 mm Hand piece weight 180g Cradle size 0115 mm max x H 68 mm Cradle weight 140g Troubleshooting Situation Troubleshooting Do not turn on the handpiece Remove and reinsert Battery If the error persists please plug in the power supply to cradle and charge the battery at least 10 min then push the ON OFF button again Do not charge the battery Please clean battery contacts If the error persists please change a new battery Display show overheat sign The temperature rises up to high really Please wait a moment and then use it again The intensity is too low If result of intensity test in Standard mode is under 700 mW cm the output is too low please contact with your dealer LEDEX WL 090 European Authorized Representative topdental TOPDENTAL PRODUCTS LTD 12 Ryefield Way Silsden West Yorkshire B
8. no operations are performed for three minutes the display will be turn off Safety mode Whenever the LEDEX WL 090 is operated frequently and or for long periods of time however the temperature may become too high and the Safety mode function will then be automatically activated to protect the light Safety mode cuts the light intensity in approx half and extends the irradiation time Refer to figure 1 When the temperature become quite high the display of handpiece will glow showing Over Heat sign Refer to figure 2 While TURBO mode was be selected it needs enough power of battery just can make a turbo light output If the status of battery power is not enough to turn on TURBO mode the Adaptive mode function will then be automatically activated to turn on the light it cuts the light intensity in approx half and extends the irradiation time Refer to figure 3 Over Heat Figure 1 Figure 2 Figure 3 LEDEX WL 090 LED Dental Curing Light EN Intensity check A built in radiometer is including in cradle While the cradle gets electric power from power supply output the light into the test area the radiometer will show the intensity of light LOW Mode cinri i eel Approx 600 mW cm 15 RAMP mogde LWY NN SEENEN dale en Approx 1000 mW cm 10 STANDARD mode Approx 1000 mW cm 10 HIGH mode Approx 1800 mW cm 10 FAST ORTHO mode Approx 1800 mW cm 10
9. rt 10 C 40 C 1096 9590 relative humidity 500hPa 1060hPa atmospheric pressure LEDEX WL 090 LED Dental Curing Light EN Properties of the LEDEX WL 090 1 The light has been manufactured with a super high luminosity 10 W LEDs The light wavelength of WL 090 is between 440 and 480 nm and the intensity is up to 2400 mW cm it can cure the composite over 2 mm in 2 sec These characteristics enable the light to polymerize almost all photosensitive composite resins 6 powerful extensive modes including Low Ramp Standard High Fast Ortho Turbo modes The turbo light guide rod is made from genuine optical fiber and not inferior acrylic that optimizes light conduction and minimizes loss of light from source to tip thereby ensuring the highest possible intensity of light at the light guide tip Advanced and high efficient cooling heat sink designed accompanied with over temperature protection A thermal protection circuit and safety mode accord to protect the light from overheating The automatic memorization of the last operation chosen is another unique feature of the light It has OLED display built in radiometer auto sleep designed for saving the energy of battery o TURBO 2 sec FAST OLED Built in Cartridge Powerful I ORTHO 2400 aexe4x3 i Sate ure 2 mm modes E pixels iometer attery LEDEX WL 090 LED Dental Curing Light EN Contents Description Numbers
Download Pdf Manuals
Related Search