User Manual
Contents
1. Programing The Remote Control There are two ways to program the remote control Automatic Code Search or Direct Entry Using Automatic Code Search Turn on the component you want to control TV VCR or DVD 2 Press and hold the component key you want to program Holding the component key until the LED on the remote control turns on then release the key Point the remote at the component press and release the UP A button then wait three seconds or until the LED stops flashing At this point the remote control is searching for the correct code to program If after three seconds the component you want to control does not turn off press and release UP A button again to tell the remote to search the next set of codes If the component you want to control does turn off Press and release OK button then the LED blinks three times Using Direct Entry Method Turn on the component you want to control TV VCR or DVD Locate the enclosed Code List Find your brand of the component you want to control Press and hold the component key you want to program Holding the component key until the LED on the remote control turns on then release the key Enter 3 digit code from the code list then the LED blinks three times If you getno response repeat these steps using the next code listed for your brand until the component responds to the remote control command Changing Volume Lock Locking the volume controls t2. amp Save The range is from 0 to 63 0 delegates the original position You can select the proper value when you has rotated the antenna Go to X Press OK key to pop up the drop down list select the proper position reference or from 1to 63 to realize the selected position West lt Save gt East Press key to turn west while press m key to turn east Press OK key to pop up the dialogue Are you sure to change this satellite s position Press OK key at the Yes button to save the current position or press OK key at the No button to cancel the operation Recalculation Press OK key to pop up the dialogue Are you sure to change this satellite s posi tion Press OK key at the Yes button to recalculation TOCOM SAT Menu Information 5 Limit Setup Press OK key to pop up the Limit Setup window Limit Setup Press za keys to switch among Disable Limit East Limit and West Limit Limit Setup Move cursor to the Limit Setup button You can press key to turn west or press r key to turn east Go to Reference Press OK key to go to reference If you select Disable Limit in the above Limit Setup item this button will turn grey 6 If select USALS Delete All item will turn grey Local Longitude Local Latitude Press zr keys to switch between West and East or press r keys to switch between North and South Press OK key to enter into the editing mode Use numeric keys 0 9 to input the longitude or lati
3. TOCOM High Definition Digital Satellite Receiver CAE D DVB S2 HD DVB S DVB S2 MPEG 2 MPEG 4 H 264 7 days EPG PVR function through USB 2 0 Automatic time change u m HDMI Media player bie F Z oea Fine Hoos leeden ECKE z H USE SE DV OUT CSN Q Contents GENERAL INFORMATION NEI Rg ci 0 Sn E E E E EE E 3 FOr VOU e EE 4 UNPACKING EE 5 cnar OPET la WE 5 KS 6 FLOREEN EE H EE E E E S EE E EE eeeteteedee H Connecting to TV USING RCA support NENNEN 8 Connecting to Riet EIElal TT 8 MATUNONU aerea E R E 9 e elei HE 10 ga Wi IR a 2 9 a EE 11 T2 VE le let eu il EE 12 Te SITS AW eeneg 13 Zs WASTAMW AMON EE 13 2 1 Antenna CONNECTION cccccescceessssceeccesseeeeesseeeccssaeeeeecsaeeeeseeeatecesesetessesseeeesesateesseneteeens 13 HH E a ee ee ee ee ee ee 13 2 3 Antenna Setup 0 0 cceccescccesssccccssseeeseeeeesssecesseeeeessseecesaeeeecseeecesseeeseseeeeeeseesessaeeeessatesseaeeess 14 2 4 Single Satellite Search 0 ee eccccccsseccssecessseesseeeesseeesseeecueesseeeeceeeessseseseesesseeesseeseseeess 16 2 SIMU aele COM E 17 PA oa E E 18 Ts OU ODD EE EE E AE N AEE EEEE A EN EEA 19 Sl LAN UA E 19 SPER LE E eee E N en EA eee ee A 20 SS Re Ed E 20 SA LOCA WINING e WEE 20 O20 HNIC DO de MEN 20 BEE EO CK EEN 21 Fy OG Gettmg ee 22 FOT NOO EE 22 TOCOMmSAT Contents 3 9 Audio Descrption Setting icise cocdcesnncrccacruwasdeairenceadoctuwars
4. the game that you want to play and press OK key to enter into the window 6 REC 6 1 PVR Storage Information Press OK key Storage Info item to know the information about the USB device TOCOM G 4T Menu Information 6 2 PVR Setting 1 Timeshift Select between Off and On 2 Jump Select among 30sec 1min 5min 10min and 30min 3 Timeshift to Record Select between On and off 4 PS Record Select between Off and On 7 Hot Key 7 1 Info Press INFO key to pop up the Info bar Press INFO key again to pop up the program guide of the current program You can press z r keys to know the pro gram guide of the future 16 days 7 2 EPG Press EPG key to enter into the EPG window 1 Press PR PR zo c keys to select up or down left or right 2 Press RED colour key to pop up the Time Bar window Press PR PR keys to select up or down while press za keys to select left or right in the time bar Press OK key at this button to return to the EPG window a Press OK key at this button to move the cursor to the current time line lt gt Press OK key to push the time forward or backward by half an hour ap Press OK key to push the time forward or backward by half an hour am Press OK key to push the time forward or backward by a day TOCOM SAT Menu Information 3 Detail Information In the EPG window press PR PR r keys to select the channel and progra
5. 2 Satellite List 1 Press PR PR keys to select the satellite up or down Press OK key to select and mark and you can press OK key again to cancel the selection and the mark 2 If there is no satellite the RED colour and BLUE colour keys will be invalid 3 Press RED colour key to pop up the Edit Satellite window Press PR PR keys to move cursor up or down Name User numeric keys to change the name of the satel lite please refer to the Edit Channel Name TOCOM G 4T Menu Information Longitude You can press r keys to switch between east longitude and west longitude After pressing OK key you can use numeric keys to edit the longitude press EXIT key or the PR PR keys to exit editing mode The range of the longitude is from 1to 180 degree If beyond this range system will inform you out of range when you press YELLOW colour key on the RCU After setting press YELLOW colour key to save and exit while press BLUE colour key to exit without saving 4 Press GREEN colour key to pop up the Add Satellite window Since the same operation as the above Edit Satel Sd lite window here we don t explain any more i CAPS DEL POX BCANCEL 5 Press BLUE colour key to pop up the dialogue Are you sure to delete Select Yes button and press OK key to delete the selected satellite You can cancel this operation by pressing OK key at the NO button 2 3 Antenna Setup Part A Fixed a Suppose that you have s
6. Channel List 1 Press 24 keys to select satellite 2 Press PR PR keys to select the program that you want to play and then press OK key to view it in the small window If move the YELLOW cursor to select up or down you will see a gray line which indicates the playing program in the small window 3 Press FAV key to move the FAV button upward Select the program and press OK key to pop up the favourite group list In the list select the group that you want to add into and press OK key and then you will find the favourite mark is displayed at the right side of the selected program Press FAV key again to exit from the fav mode and you will find the FAV button return to the origin position 4 Press RED colour key to move the Lock button upward Select the program and press OK key to mark this program with the Lock mark You can cancel this mark by pressing OK key once more Press RED colour key again to exit from the lock mode and you will find the Lock button return to the origin position TOCOM SAT Menu Information 5 Press GREEN colour key to move the Skip button upward Select the program and press OK key to mark this program with the skip mark You can cancel this mark by pressing OK key once more Press GREEN colour key again to exit from the skip mode and you will find the Skip button return to the origin position 6 Press YELLOW colour key to move the Move button upward Select the program and pres
7. List Box if the column has 34 mark You can also use the numeric keys on the RCU to enter numeric value Use the PR PR key to move upwards and downwards from one line to another line and use 1 key to move from main menu to sub menu and move from left side to right side or versa Meantime you want to escape the menu system please press MENU or EXIT key on the RCU f there is no program you can not exit from the Main Menu window by pressing MENU or EXIT key System will inform No channel and the following items turn grey Submenu Turn grey when there is no program e TV Channel List Radio Channel List Delete all Antenna Connection Antenna Setup Multi Satellite Search Language Local Time Setting Parental Lock Favorite Display Setting Information Upgrade by USB Remove USB devicesafely Othello Sudoku PVR Storage information e PVR Setting Channel List Satellite List Single Satellite Search TP List TV System Timer Setting OSD Setting Audio Description setting Other Factory Setting Media Player Network Local Setting Installation TOCOM SAT Menu Information 1 Edit channel 1 Press OK key or key to pop up the Input Password dialogue you can not enter into the menu unless the correct password is inputted The default password is 0000 2 Press PR PR keys to move the cursor up or down 3 Press EXIT key or key to move the focus to the left menu 1 1 TV
8. O 0CO N amp 01 amp JIN Ifthe name is empty system will pop up a dialogue informing Name once YELLOW colour key is pressed Press OK key to close this dialogue iii Delete BLUE colour key In Delete window press BLUE colour key to move the Delete button upward Select the program and press OK key to mark this program with the deletion mark You can cancel this mark by pressing OK key again Press EXIT key to pop up the dialogue Are you sure to save Select Yes button and press OK key to save or select NO button and press OK key to exit without saving 1 2 Radio Channel List Sine the same operation as 1 1 TV Channel List here we don t explain any more TOCOM G 4T Menu Information 1 3 Delete All Move cursor to the Delete All item and press OK Key to pop up the dialogue Warning Do you really want to delete all channel Press EXIT key to pop up the dialogue Are you sure to save Select Yes button and press OK key to save or select NO button and press OK key to exit without saving 2 Installation 1 Press OK key or e key to pop up the Input Password dialogue you can not enter into the menu unless the correct password is inputted The default password is 0000 2 Press PR PR keys to move the cursor up or down 3 Press EXIT key or key to move the focus to the left menu 2 1 Antenna Connection Press a keys to select between Motor Antenna and Fixed Antenna 2
9. arpmess Press zr key to select from 0 9 3 4 Local Time Setting 1 Summer Time Select between ON and OFF OFF delegates the normal time If select ON time will add one hour 2 GMT Offset When select ON in GMT Usage item system will get the date and time information from the screen automatically Date and Time two items will turn grey Select the proper option in the GMT Offset item Thedefault setting is GMT ON 3 Date Time When select OFF in GMT Usage Date and Time two items take effect while GMT Usage turns grey Use numeric keys to input the desired value 3 After setting press MENU key or EXIT key to exit and save If the value is invalid system will inform Invalid input Continue to edit Press OK key at the Yes button to continue the modifica tion or press OK key at the No button to exit without saving 3 5 Timer Setting If there is no program you can not enter into this window There are 8 timers that can be set Select Timer up or down and press OK key to enter into the setting window 1 Timer mode The default mode is off You can set the timer once daily weekly monthly and yearly TOCOM SAT Menu Information 2 Timer Service Select between Channel and Message If Channel is selected the Wakeup Channel is displayed in the following item If Message is selected the Wakeup Mes Sage is displayed in the following item In wakeup message you can select among Birthday Anniver
10. change in product design or performances as progress in engineering or technol ogy Main Features m MPEG4 HD with Twin tuner m Smart Card Reader m SCPC and MCPC receivable from C Ku band satellite m FULL HD 1080P m 5000 channels TV and radio program mable m 8 different favorite groups selection m Multi language OSD m Electronic Program Guide EPG m Picture in Graphics PIG support m 256 color On Screen Display m Automatic network search for newly added transponders m DiSEqC 1 2 fully support 13 18V 0 22K m Various channel editing functions favorite moving locking renaming deleting and sorting m Parental control for channels m Easy to use Menu System m imer Reservations automatically switch to a specific channel Automatic save for last channel m Channel list can be sorted by alphabetic A Z Scramble Favorite Lock Sat m Support FAT 12 FAT16 FAT32 NTFS m Software update by USB m JPEG viewer m MEDIA PLAYER m MP3 OGG support m AVI MKV MP4 support TOCOM G4 T General Information For your Safety 1 To avoid electric shock hazards do not open the cabinet refer servicing to qualified personnel only 3 Do not expose the receiver un der the sunlight And keep it away from the heat source 5 When the abnormal phenomenon occur you should cut off the power immediately 7 Switch the receiver off whenever it remains out of service for an extended period 2 Keep the receiver away
11. dow are displayed on the down part You can press r keys to switch among them 2 FTA Only Press z r keys to select between Yes and No 3 Scan Channel Press zx keys to select among TV Radio TV Channel Radio 4 Network Search Select between No and Yes This item turns grey when Auto Scan is selected in the following Scan mode item 5 Scan Mode Press r keys to select between Auto Scan and Preset Scan Auto Scan is Blind scan while Preset Scan is to search the preset frequencies 6 Search Press OK key to start searching TOCOM G 4T Menu Information 2 6 TP List 1 Press PR PR keys to select the proper satellite 2 Press RED colour key to pop up the Edit TP window Frequency Symbol rate Dress za keys to add or reduce by step one Or press numeric keys 0 9 to input the desired value The range of the frequency is 3000 13450 while the range of the symbol rate is 1000 45000 The inputted value is beyond this range the value will return to the origin value Polarity Press a m keys to switch between Vertical and Horizontal 3 Press GREEN colour key to pop up the Add TP window Since the same operation as the above Edit TP window here we don t explain any more 4 Press YELLOW colour key to pop up dialogue Are you sure to delete Press OK key at the Yes button to delete the selected TP or press EXIT key to cancel the operation 5 Press BLUE colour key to pop up the TP Search
12. easennabdosaphaohdestimuasJesautenddecteneddexsacuienss 22 STOOT ee 22 A La e E 23 GER Tute le EE 23 EZ e ee ET Le WE 23 e E el DYU E 23 e NIG GIN GE 24 4 5 Remove USB device safely 00 cccccccscecsssccsssecessecesseescseeessseessseessseesssseeseseesseesssseeeenaes 29 4 6 Network Local Setting wcsisnivcsccsicneascnscssmnseecilsscnceeestwoascnsasies ssuint dveasenestanseunstanesenssbonecerasuecsemecexs 25 RE A e E A A E A AE EA E ee 25 KA 25 6 1 PYR SOFA SHO HANOI DEE 25 CZP YR SOUNO ME 26 T TAO EE 26 s MUN WEE 26 E i EE 26 Teo TAINO EE 27 e NUDO EE 2 1 5 TVIRADIO 0 cccccccccccsseeccseeecsseeecseeecsaeeccseeecseeescseeeeaeescaescseeesesaesssseesesaeessseessseessneeeseneess 27 7 6 Up Down Channel Change 27 T ale VOMITING EE 2 Aca 0 eee ee E N A TNE E AEE 27 ERT 2 TWO OU eebe 28 EMV Cell ME 28 MR ORS UE 28 UW AE 28 Tee NO OU ON ote dase E E E E E E NN E gece 29 KISLO ER 29 Trouble Shooting RCU Information TOCOM SAT General Information A Digital Satellite Receiver is a convenient product that allows you to view a variety of programs provided through satellite This user s guide covers the installation of the DSR and the necessary steps to implement various features This also explains special features available only in this DSR in detail which will allow you to make full use of these feature Information confirmed in this document is subject to change We reserves the right without notice to make
13. elected Fixed Antenna in the en Antenna Connection window VE Are you swg bo dalela ME Ho 1 Satellite All selected satellites in the satellite list are displayed in this item Press keys to select the satellite in circle Or press OK key to pop up the drop down list then select the desired satellite in the list and press OK key to confirm 2 LNB Freq Transponder DiSEqC1 0 DiSEqC1 1 The same operation as the above 3 22K Polarity You can press r keys to select in circle TOCOM SAT Menu Information Part B Motor Suppose that you have selected Moter Antenna in the Antenna Connection window 1 LNB Type Select the proper LNB type 2 Motor Type Select between DiSEqC1 2 and USALS If you select DiISEqC1 2 the following Local Longitude and Local Latitude items will turn grey Aro you sura io cloar sat Sakeile posiies of ihig lute 3 Delete All Press OK key to pop up the dialogue Are you W s No sure to clear set satellite position of this tuner Press OK key at the Yes button to clear all the memories about the posi tion of the satellites that are connected to the tuner 4 Motor Setting Press OK key to the Motor Setting window Satellite Press n keys to select the satellite in circle Or press OK key to pop up the drop down list then select the desired satellite in the list and press OK key to confirm Transponder The same operation as the above Position No
14. enu Information 7 10 OK 1 During the viewing or listening press OK key to pop up the TV program list or the Radio program list 2 Press PR PR keys to select the channel up or down and then press OK key to play this channel in full screen 3 Press za keys to select the satellite 4 Press MENU or EXIT key to close this window 7 11 Audio 1 Press Ch keys to enter into the Audio window 2 Press za keys to select among Left Right Stereo and Mono 3 Changing the audio mode is only connected with the current channel not all the channels 4 Press MENU or EXIT key to close this window 7 12 Recall Press RECALL key to switch the current channel to the previous channel 7 13 FAV 1 Press FAV key to pop up the favourite group window 2 Press za keys to select the favorite group Press PR PR keys to select the channel up or down Press OK key at the selected channel to view it in full screen Press MENU or EXIT key to exit 3 If there is no favorite channel system will inform No FAV Channel when you press FAV key TOCOM SAT Menu Information 7 14 Teletext Press TXT key to open the teletext on the screen If there is no teletext system will inform No Teletext Data Press EXIT key to exit 7 15 Zoom 1 Press ZOOM key to switch among Zoom 1 Zoom 2 Zoom 3 Zoom 4 Zoom Zoom 6 Zoom s Zoom 12 Zoom 16 2 In zoom mode press PR PR zc keys to move the curso
15. from flower vases tubs sinks etc in order to avoid damaging the equipment 4 Do not block ventilation holes of the Receiver so that air can circulate freely 6 Do not touch the receiver during thunder since that might create electric shock hazards 8 Be sure to turn the Receiver off and disconnect the AC power cord before cleaning the Receiver surface lf the surface is dirty wipe clean with a cloth which has been dipped in a weak soap andwater solution and wrung out thoroughly and then wipe again with a dry cloth General Information Remote Control Guide Audio Video cable General Operation 1 Throughout this manual you will notice that the everyday operation of the receiver is based on a series of user friendly on screen display and menus These menus will help you get the most from your receiver guiding you through installation channel organizing viewing and many other func tions 2 All functions can be carried out using the buttons on the RCU and some of the functions can also be carried out using the buttons on the front panel 3 The receiver is easy to use always at your command and adaptable for future advances 4 Please be aware that new software may change the functionality of the receiver 5 Should you experience any difficulties with the operation of your receiver please consult the relevant section of this manual including the Problem Shooting or alternatively call you
16. m and press INFO key to know the detail information of the current program 4 Press GREEN colour key to enter into the Timer window You can add the current program to the Timer If 8 timers are already yet system will inform you Timer is fulll 7 3 Find Press FIND key on to pop up the FIND window Use numeric keys to enter into the character and use the colour keys to realized the corresponding operation 7 4 Number CAPS DEL SOK Use the numeric keys 0 9 to input the number of the desired channel If the inputted number is beyond the valid channel number system will No such a channel and press OK key to close this message 7 5 TV RADIO In normal mode press TV RADIO key to switch between TV mode and Radio mode 7 6 Up Down Channel Change Press PR PR keys to change the channel up or down If in the all satellites group you can select channel in all searched channels If in the specific satellite only can select channel in the satellite group 7 7 Left Righ Volume Press keys to change the volume Press zakeys to decrease the volume while press keys to increase the volume 7 8 Mute Press X key to turn off the volume You can press X key once again to restore the volume or press z keys to increase the volume 7 9 Pause During the viewing you can press PAUSE key to stop the picture while the volume continues You can play the picture by pressing PAUSE key once again TOCOM SAT M
17. me size time and favorite 2 Press ZOON A B to select the repeat mode 3 Press SAT Swap to change among Video image music and Record window e RED key Press RED key to enter the rename window you can rename the file by press number 0 9 on RCU e GREEN key Press GREEN key to enter the copy window pressza key to select the place you want to copy to and press GREEN key to begin copying e YELLOW key Press YELLOW key to add the delete symbol on your selected file press YELLOW key again the symbol will disappeared Press OK key on the file with delete symbol it will pop up a dialogue Are you sure to delete Select YES to delete and select NO to quit without delete the file and press EXIT key to quit without delete the file e BLUE key Press BLUE key to enter the New Folder window you can press number 0 9 to edit TOCOM G 4T Menu Information 4 5 Remove USB device safely Press OK on this item it will pop up a dialogue You can safely remove USB device now then you can move your USB device safely 4 6 Network Local Setting DHCP Select between ON and OFF when it ON the IP Address Subnet Mask and Gateway item will turn gray you can not edit them Press number 0 9 the input the address 5 Game 1 Press OK key or e key to enter into the game 2 Press PR PR keys to move the cursor up or down 3 Press EXIT key or za key to move the focus to the left menu 4 Select
18. o a single device makes it easier to control volume without having to guess whether the volume will change If you lock the remote s volume controls to the TV you will always be able to change the volume to the level you want without having to adjust it on multiple devices If you want to lock the volume for the STB component 1 Press and hold the STB component key until the LED on the remote contro turns on 2 Enter 3 digit code 9 9 9 3 Press and release the STB component key then the LED blinks three times Unlocking volume control If you want to unlock the volume for the STB component 1 Press and hold the STB component key until the LED on the remote control turns on 2 Enter 3 digit code 9 9 9 3 Press and release the STB component key then the LED blinks three times TOCOM G 4T
19. r dealer or a customer service adviser TOCOM SAT General Information AUDIO TEXT SUBTITLE gt e TV VCR DVD STB 0 9 TV RADIO RECALL FIND V Format EPG AUDIO OK LIST MENU INFO EXIT Dect PAGE PAGE PR PR lt gt gt E RECORD SAT TV AV ZOOM SLEEP FAV TXT SUB TITLE ee Turns power ON OFF of the DSR When watching a channel mute the sound Press each button to changes the mode of RCU Enter number of the required menu item or select a channel number to watch Switches between TV and Radio mode Switches back to previous channel Display the Find window Select Video resolution Call up the EPG Electronic Program Guide Display the Audio window Executes the selected item in the menu screen or enters the desired value in any input mode Press this key one time to run menu on screen Show information of the current channel Return to the previous menu on the menu screen or escape from the menu When watching a channel adjust the volume or move to the left or right item in the menu Moves up down a page in the list When watching a channel change channels or move to the next higher or lower item in the menu Press to fast Forward or fast backward Play and stop the program Press once to pause the screen picture press once again to go to the normal mode Record the program Display the satellite list Switch between TV and AV mode
20. r up left right down 3 Press MENU or EXIT key to exit 7 16 Subtitle Press the Subtitle key to display Subtitle TOCOM G 4T Trouble Shooting Problem Possible causes What to do EE nig front e Main cable is not connected sigs a ANEDE panel does not light up plugged into the power socket No sound or picture but the e The receiver is in standby mode Press the standby button front panel shows red light e The satellite dish is not pointing Adjust the dish Check the signal at the satellite level in the Antenna Setup menu No sound or picture e No signal or weak signal e Check the cable connections LNB and other equipment connected between the LNB and the receiver or adjust the dish e The satellite dish is not pointing e Adjust the dish at the satellite e Connect a signal attenuator to the e Signal is too strong LNB input Bad picture blocking error e Change to a larger dish e Satellite dish is too small e Change to an LNB with lower noise factor e The LNB is faulty e Change the LNB e LNB noise factor too high e Battery exhausted e Change the batteries The RCU is not working W e Aim RCU at the or check that e RCU is incorrectly aimed nothing blocks the front panel Note If you have tried all of the actions suggested above without solving the problem please contact your dealer or service provider TOCOM G 4T RCU Information
21. re are 32 favorites group listed in this window Press PR PR keys to select one and press OK key to the Rename window Since the same operation as the above the Add Satellite window here we don t explain any more 3 9 Audio Description Setting When you input to Favorite menu you will see a screen like below 1 AD service Enable Disable AD function 2 Use AD as default Show AD information by enable AD mode when play AD stream 3 AD Volume Offset Adjust AD vol 3 3 3 10 Other 1 LNB Power Select between Off and On 2 Channel Play Type Select among All Free Scramble 3 Channel change Select between Black screen or Freeze 4 Auto standby Select on off TOCOM SAT kat k E O wi kat 28 i E wi Menu Information 4 Tools 1 Press OK key orza key to pop up the Input Password dialogue you can not enter into the menu unless the correct password is inputted The default password is 0000 2 Press PR PR keys to move the cursor up or down 3 Press EXIT key orzakey to move the focus to the left menu 4 1 Information Press OK key to the Information window 4 2 Factory Setting Press OK key to enter into the Factory Setting window Select Yes button and press OK key to return to the factory setting All searched channels and set information will be erased Select No button and press OK key to cancel this operation or press MENU or EXIT ke
22. s Enter into the zoom in mode Enter into the sleep in mode Displays the favorite group list Display teletex Display subtitle TOCOM G 4T General Information Front Panel Rear Panel LNB 1 IN CONNECT TO SATELLITE ANTENNA LNB 1 OUT CONNECT TO THE OTHER RECEIVER LNB 2 IN CONNECT TO SATELLITE ANTENNA LNB 2 OUT CONNECT TO THE OTHER RECEIVER CONNECT TO AUDIO R L TO TV OR AUDIO TUNER CONNECT TVIDEO TO TV USING RCA JACK CONNECT TO APC FOR S W UPGRADE i POWER ON OFF CONNECT TO USB FOR S W UPGRADE OR PVR FUNCTION CONNECT TO THE INTERNET CONNECT TO FOR DIGITAL A V CONNECT TO A DIGITAL AMPLIFIER CONNECT Y Pb Pr TO TV USING 3RCA JACK TOCOM G 4T Installation Connecting to TV using RCA support Satellite Dish Sg _ Connecting to Digital Amplifier DIGITAL AUDIO CONVERTOR OR AMPLIFIER DIGITAL AUDIO SPEAKER TOCOM SAT Menu Information Make sure that you have properly installed and connected the cables of the receiver If the receiver is the factory status or there is no program list when power on the Main Menu window will be displayed on the screen During the normal TV Radio mode press MENU key on the RCU to enter into the Main Menu window ck This menu consists of 6 major main menus as follow Edit Channel Installation System Setup Tools Game REC During the installation the OK key confirms a selection and LIST key shows Down
23. s OK key to mark this program with the move mark Press PR PR keys to move the cursor to the position where you want to locate and press OK key to confirm Press YELLOW colour key again to exit from the yellow mode and you will find the yellow button return to the origin position 7 Press BLUE colour key to enter into the Edit channel window i Sort RED colour key Press RED colour key to pop up the Sort drop down list Name A Z The ascending order omitting the character the number is ahead then the capital letter at last the lower case Name Z A The opposite order of the above Name A Z Free Scramble All FTA programs are listed ahead while all scrambled programs are listed last Lock all locked programs are listed at the last Default TOCOM G 4T Menu Information li Edit GREEN colour key Press GREEN colour key to move the Edit button upward Select the program and press OK key to pop up the Rename window In Rename window press RED colour key to switch between capital letter and lower letter press GREEN colour key to I cies occ sorsomon delete the character on the cursor press 1 keys to move the cursor left or right press numeric keys 0 9 to input the character please refer to the down table Press YELLOW colour key to save and exit or press BLUE key to cancel and exit Press numeric key repeatedly display in circle CO O
24. sary General At the same time the duration item turns grey 3 Wakeup Date On Time Use numeric keys to input the valid date Duration Set the gap time After waking up system will power off automatically after the duration time Press MENU or EXIT key to save and exit 3 6 Parental Lock Before entering into the Parental Lock window you need input the correct password The default password is 0000 1 Menu Lock Press keys to select between Off and On If select On you can not enter into the window before entering the password 2 Channel Lock Press keys to select between Off and On The default value is Off If select On you can not view the locked channel set in Chanel List Edit window until you have inputted the correct password 3 New Password User numeric key 0 9 to input the new password 4 Confirm Password Input the new password once again Confirm password must be the same as the New password System will inform you Change password successfully while they are the same or inform you to input the password of Confirm password once again when they are not the same TOCOM SAT Menu Information 3 7 OSD Setting 1 OSD Timeout Press c keys to select from 1 to 10 by step1 The default values Is 5 2 OSD Transparency Press z r keys to select among Off 10 20 30 40 The default option is Off Press MENU or EXIT key to save and exit 3 8 Favorite The
25. tude press MENU key or EXIT key to exit The range of the longitude is from 0 to 180 while the range of the latitude is from 0 to 90 If the input ted value is not in this range system will pop up a dialogue Out of Range when you exit from this window You can press the OK key to close this dialogue 7 Motor Setting Press OK key to enter into the Motor setting window Satellite Transponder Press r keys to select satellite or transponder or press OK key to pop up the drop down list and select in the list 2 4 Single Satellite Search 1 Satellite Press zi r keys to select the satellite in circle Or press OK key to pop up the drop down list then select the desired satellite in the list and press OK key to confirm 2 FTA Only Press zc keys to select between Yes and No TOCOM SAT INS KU ARABSAT 2 Menu Information 3 Scan Channel Press r keys to select among TV Radio TV Channel Radio 4 Network Search Select between No and Yes This item turns grey when Auto Scan is selected in the following Scan mode item 5 Scan Mode Press keys to select between Auto Scan and Preset Scan Auto Scan is Blind scan while Preset Scan is to search the preset frequencies 6 Search Press OK key to start searching 2 5 Multi Satellite Search From the Multi Satellite Search window you can search several satellites at the one time 1 Satellite All selected satellites in the satellite list win
26. window FTA only Scan Channel Network Search Press z4 keys to select the proper option Press OK key at the OK button to start searching TOCOM G 4T Menu Information 3 System Setup 1 Press OK key or key to move the cursor to the right menu kat i 2 Press PR PR keys to move the cursor up or down bs 3 Press EXIT key or za key to move the focus to the left menu 3 1 Language 1 Press OK key to enter into the Language window Press r keys to select the language in circle while press PR PR keys to move the cursor up or down in circle 2 Press MENU key or EXIT key to save and exit 3 The types of the language pleaser refer to the configura tion of the customer 3 2 TV System Press PR PR key to move the cursor up or down while press za keys to change the setting and the setting will take effect immediately 1 Video Resolution Select among 480i 576i 480p 576p 720p and 1080i 1080p 2 Aspect Mode Select among 4 3 Letter Box 4 3 PanScan 16 9 and Auto 3 Video Output Select between RGB and YUV 4 Digital Audio Out Select among LPCM Out and BS OUT TOCOM G 4T Menu Information 3 3 Display Setting 1 Brightness Press zr key to select from 0 100 2 Contrast Press z key to select from 0 100 3 Saturation Press r key to select from 0 100 2 i GR 4 Hue Press r key to select from 0 100 5 Sh
27. y to cancel and exit 4 3 Upgade by USB 1 Upgrade File Show the Upgrade File 2 Upgrade Mode Select between All Code and Dump When users switch the upgrade mode Upgrade File will show the corresponding file according to the table below Upgrade Mode File feature All code File named as bin Select the upgrade mode and upgrade file then you can start upgrade by USB TOCOM G 4T Menu Information 3 Press OK key on start bitton to start receiving the data from USB device When the USB device is not connected this item is grey you can not edit it now 4 4 Media Player This menu will be disabled when no USB device is plugged Media Play List will not be saved when USB plug out or standby or power off Move scroll bar when press up down key page up or down by page key Go into sub directory when press OK key in the file W directory play the selected file when scroll bar is on the file gata orv mn otar Sort Repeal Exil automatic return USB menu after play is over Color key operation 1 GREEN key Press GREEN key to add the favorite symbol on your selected files and put the file selected by scroll bar to play list 2 YELLOW Key Press YELLOW key to add all the image and music files to the play list 3 RED Key Show the Play List 4 BLUE Key Press BLUE key to enter the edit window Function key 1 Press TV AV Sort to pop up a window In this window you can know na
Download Pdf Manuals
Related Search