Before using device, read the user manual caref
Contents
1. press R button on Zed BULL keypad transponder details will be displayed on the screen DATA 00008003D89D0515 761348C2B7480000 TYPE 73 MTSB VOLVO WR The details of the chip will be displayed on the screen Next you will press the W button Suitable transponders to write onto will be displayed on the Zed BULL screen remove customer key from antenna and insert suitable transponder Select Choose Which Type Of Chip You Will Use 1 Philips 7930 31 35 2 Sokymat T5 the transponder type by pressing the listed numbers on the display After transponder type is selected and enter button is pressed the following expressions will be seen on Zed BULL screen WRITING VERIFIYNG SUCCESSFULL transponder cloning process is completed If transponder needs to be cloned with PC software Copy with PC Software expression is displayed on the screen All 4D transponders are cloned to Silca Electronic Heads EH2 or JMA batteryless TPX2 transponders with Zed BULL 4D client PC software FF 00 50EADAOC L TYPE 4D 60 CRYPTO WR Copying 4D transponders is possible only with Zed BULL Client PC Software User must connect to server to copy 4D transponders Zed BULL PC Software connects to the server and gets neccessary datas to write on to electronic key User should choose correct communication port car manufacturer car model and model year if these informations are not selected correctly copy operation2. L Device Token 0 Left side of the window is reserved for EEPROM and MCU applications Picture of the immobox and suitable adapter of the IC programmer is displayed on left bottom side Details of the selected module is displayed on the text box just below the selected module When IC programmer adapter picture or immobox picture is clicked bigger picture of each is displayed on another window the IC that must be removed from board is marked with red buble See the pictures below The EEPROM or MCU of the selected module is read with IC 17 Programmer File with bn or dat extension is selected using open file button from the exact location of the file in PC hard drive After choosing the correct file choose the format correctly if the output file of the IC programmer is 8 bits use 8 bit format if the output file of the IC programmer is 16 bits use 16 bit format Choosing wrong format will cause corrupted data and calculated datas will be wrong To programme transponder place the correct transponder to the Zed BULL antenna and click on button programme transponder The Eeprom amp Mcu application list is given in Appendix A As long as new solutions are obtained number of the applications will be increased soon new applications will be added to software with new updates Important Notes User must use external IC programmer to read the Eeproms and Mcus The pictures of the IC programmer in Zed
3. This device is produced for assisting automotive locksmiths Before using device read the user manual carefully Avoid strokes to device and accessories Avoid device and accessories contacting with water and conductive liquids Use only original accessories After using device unplug power adapter Do not use device under high electromagnetic field Use the device in a sturdy dust free well ventilated place Updated user manuals will be available at web After using device unplug all accessories and keep them in the package Do not place heavy materials on the package Keep package in room conditions Clean the device with soft and dry piece of cloth If a problem occurs do not disassemble the device Contact your local distributor or device manufacturer Complete package Zed BULL security login card PC Usb cable Power Adapter Lighter Adapter Transponder box Width 285 mm Height 285 mm Depth 105 mm Weight 0 6 kg External Power Supply 100 250 V 50 60Hz AC Current 117 mA Power consumption 1 05 Watt Adapter 9 12 V DC Transponder Freguencies 125 134 Khz Communication Interface USB and Serial Port Temperature range 5 C to 40C Zed BULL is a friendiy automotive locksmithing tool it has been developed for all range of automotive locksmiths from beginners to advanced It s ease in use technical support and unique properties makes it a powerfu
4. This menu is used for preparing transponders to use with diagnostic devices Transponders that can be produced with this menu is listed below 40 opel 41 nissan 42 VAG 44 Mitsubishi 44 VAG 45 Peugeot 46 61 62 65 and 73 Mitsubishi When transponder type is selected key number options are displayed on the same window under transponder type options area Both transponder type and key number must be selected before clicking the button produce transponder Transponders with different key numbers can be programmed to same car The Blank transponder to use is shown in Red Just over the produce transponder button On the right side of the window according to the selected transponder type matching car models are displayed zi Tod e TRANSPONDER CATALOGUE KEYFOB DATABASE DISTRIBUTOR SETTINGS UPDATE SUPPORT CONTACT MAIN MENU EXTENDED FUNCTIONS TRANSPONDER PRODUCTION Factory Contig TRANS PONDER Crypto L SR SL ME 00 Crypto Hi d SAL Secret Key Lock OTF z 515 Factory Config O PG3L Page 3 Lock TRANSPONDER e Mi J PPT Page Write Protect 1 PCF 336 O PCF7341 PWPO Page Write Protect 0 PCF7942 44 PCF7946 7 00 oo oo oo USER 3 Gr 9 2 212 S S S Z S EN Enable Crypto Made H51 Read Only Mode
5. Settings PIN Code Reader Highlight choice 4 using up and down arrows and press enter When there is transponder inside the key TRANSPONDER expression will be displayed on Zed BULL screen if there is no transponder inside the key only TEST expression will be displayed on the screen for some seconds and main menu will be displayed back gt gt TRANSPONDER lt lt TEST This menu is used for choosing device language updating device getting device info and loading device token Usage Highlight choice 5 using up and down arrow and press enter for language selection highlight choice 1 and press enter language options will be displayed on the screen Highlight your language using up and down arrows and press enter selected language choice is now activated Use Esc button to 13 return back to main menu MENU 1 Language 1 2 Update Firmware 2 Update Firmware urkce Englisch 3 Deutsch taliano 5 Dansk Device Info Device Into 4 load Device Token Update Firmware When user wants to update device this choice should be selected The loader version and the serial number is displayed on the screen To quit this menu device needs to be re started Detailed information of firmware update is described in the Pc software settings sub menu MENU Zed BULL Language 1 Language LOADER V 0 3 Update Firmware Update Firmware 3 Device Info UPLOAD ZBC F LE Device Info
6. antenna and click the programme transponder button on Zed BULL Pc Software precoded transponder is prepared 5 Do not remove the transponder from antenna press Create Image File 19 button on Extended Function Menu Save the file with different name such as m image bin or image dat in order not to overwrite on to the previous file 6 Using the IC programmer write the file that you saved to the eeprom or Mcu of the immo board The process is completed The tranponder will start the car directly v re Zed DULL err e DISTRIBUTOR SETTINGS UPDATE SUPPORT CONTACT 1 TRANSPONDER PRODUCTION HITAG2 13066 8 pin 512 Bytes Fiat Altar Lanci m gt ni Prepare 11 Temiz Transponder Data Transponder Type Megamos Lrupto Programme Transponder to car with diagnostic device Prepare 11 Temiz Transponder Data from 3 eeprom byte SE Calculate E W rs F gc E m Programme Transponder Create Image File n 16bit I Calculate Pin Code Kla HTUNDAJ E Calculate Pin Code from last B digits of VIN a Calculate Pin Code Device Token 0 Right top side of the main menu window is reserved for preparing data for 11 12 temic 13 megamos 4C texas and 33 renault transponders from eeprom bytes This feature is added to the software for professionals If the location of bytes that is related with transponder data is known thi
7. company directly 26 QUALITY MANAGEMENT SYSTEM OF ISTANBUL ELEKTRONIK ANAHTAR VE GUVENLIK SIS SAN TIC LTD STI IS REGISTIRED WITH THE STANDARD ISO 9001 2000 STANBUL ELEKTRON K ANAHTAR G V SIS SAN T C LTD T ADRESS HOCA UVEYZ MAH VATAN CAD NO 40 A FAT H STANBUL T RK YE PHONE 0090 212 621 5793 FAX 0090 212 621 5796 E MAIL info istanbulanahtar com support istanbulanahtar com wwwi istanbulanahtar com OCTOBER 2008 25 Appendix A Precoded Transponder Automatic Detailed Detailed Eeprom amp MCU Applications Transponder for ready to start EUR module immo box immo board Diagnostic the car recognition picture picture 1 Opel immo2 Siemens immobox X A A A A A 2 VW Seat immo2 Siemens immobox X A A A A A 3 VW Seat immo3 Valeo immobox X A A A A 4 Fiat Lancia Citroen Peugeot Delphi immobox X A X A A 5 Opel immo1 Siemens immobox X A A 6 Honda Acura Megamos immobox X A X A dr Honda Rover Valeo immobox X A X A A A 8 Fiat Lancia imm001 01 magneti marelli immobox X A A A 9 Fiat Lancia imm110 01 magneti marelli immobox X A X A 10 Mercedes Sprinter Vito Vw volt Temic immobox X A A A A 11 Fiat Afa Romeo Lancia magneti marelli immobox dr A 12 Fiat Citroen code2 Delphi immobox A A A 13 VW Skoda Seat immo1 Siemens immobox X dr 14 Daihatsu 1998 2000 X A X X N N 15 Daihatsu 2000 2001 X X
8. device Is turned on before logging in number of tokens 16 digit device serial number device software version device applications information ZB refers to Zed BULL which is consisted of transponder cloning functions E refers to Eeprom application T refers to Transponder production application are displayed on the Zed BULL screen Tokens are loaded as in the steps below 1 Choose 5 choice settings in the main menu 3 Device will give Outcode outcode should be sent by e mail to token istanbulanahtar com as a reply of this e mail user will get In code this In code should be entered carefully and correctly to the device if In code is entered wrong repeatedly 5 times device will want new In code If In code is entered correctly tokens will be loaded to the device Or tokens are loaded directly by PC software Settings sub menu Is selected Reguest outcode button is clicked E mail adress of the user is entered Send button is clicked As a reply an Incode will be sent to the e mail address entered 0 00 D 8 ae Pe Fan FET iia E m POMPE E feet Trepi nn Ee urna ra ae pa paya L kt elf og geg Dumb Each ep L i Lo OL DCH arr h re L Raiber remenin _ Ta G In code should be entered carefully to the Incode box Enter In code button is clicked If successfull tok
9. for most of the car models v reen Tod ww e MAIN MENU EXTENDED FUNCTIONS TRANSPONDER PRODUCTION HITAG2 TRANSPONDER CATALOGUE DATABASE DISTRIBUTOR SETTINGS UPDATE SUPPORT CONTACT 1 with the doors shut and from inside the vehicle 2 Turn ignition to position 1 and back to off within 5 seconds 3 Remove key from ignition and press and hold the unlock button has an arrow it for 15 seconds during this time press the key lock button haz car logoja times within 5 seconds 4 Release both buttons 5 Doors will lack and unlock to show correct programming has occurred 13 Fiat Lancia 2U Mitsubishi Programming key fobs manually is described step by step in this sub menu On the left side of the window car type is selected and on the right side of the window programming procedures are displayed in a text box 9 Zed DULL e e MAIN MENU EXTENDED FUNCTIONS 1 TRANSPONDER PRODUCTION HITAG2 gt TRANSPONDER CATALOGUE KEYFDE DATABASE DISTRIBUTOR SETTINGS UPDATE SUPPORT CONTACT nee 7 Load Transponder Data Car Model ID Note OPEL VALUSHALL S000F0000070E OFS0F FCF SOF OOF FOF my car __ Device Token 0 23 Unlimited number of cust
10. internet connection If customer transponder data is present it is possible to type these datas manually using Zed BULL keypad In main menu highlight choice 3 using up and down arrows and press enter Read amp Identify Clone Chip anual Programmi Test settings PIN Code Reader of transponder will be asked to user Using up and down arrows choose transponder type that you want to write data Manual Programming Temic 12 Megamos 13 Philips 33 Texas 4 Press enter using key pad type the datas manually and press enter Use up and down arrows to choose the type of transponder that the datas will be written into Finally press W button to write datas to the transponder Manual Programming Enter Transponder Data An important point is that the data entered manually must include valid 12 information for the 11 12 13 and 4C type transponders Before writing process starts Zed BULL checks the validity of the data and informs the user if the data is non valid For example ID 11 should have at least 1 5F byte in data string ID 12 should have at least 1 C1 byte in data string ID 13 should have at least 1111 1111 xxxx xxx1 bit string in data string ID 4C Cre calculation must be valid for the data string This menu is used for checking whether key has a working transponder inside or not Usage Read amp Identify Clone Chip IX 13
11. models are displayed on the Zed BULL screen Also for Renault 33 transponders pin code of the car is diplayed Usage Insert customer key to the Zed BULL antena and Press R button on Zed BULL keypad or use up and down arrow to highlight choice 1 on main menu and press enter right arrow MENU 2 Clone Chip Manual Programming 4 Test 6 PIN Code Reader An important point is while reading the transponder It should be put on the antenna perpendicular See pictures below Zer BL Pium Zed Bull screen displays of some of identified transponders are as below er _ A ae LAT MI NADOPAARA29DRAN JATA I1 AC BARC N 101810 A H PPS rx N En A MN i IA ie ei Viu JK 4 yay LA F I FSI D D DATA 5F000000071AB07D DATA 3E8199C1A3A3261D DATA LETUALODUUUUUUUL Sis PP EQ000 AA A IT TYDE 4 TKR LAK 1 s 5 VW if lt m D VV R T VY P Ar TEXAS WR eis Si 6 sias I X I CAAS VYA TYPE 41 CRYPTO NIS WR TYPE 42 CRYPTO VAG WR p ADA4ADEPEQ9414 Bi VU l 0 7067 This menu is used for duplicating transponders Usage Insert customer key to the Zed BULL antenna and highlight choice 2 Clone chip on main menu and press enter right arrow ATTENTION 1 Read amp Identify Put The Original Key Zi Clone Chic And Press R 3 Manual Programming 4 Test 5 Settings 6 PIN Code Reader Dont Remove The Key During Process
12. 4 Load Device Token Test denge PIN Code Reader S NO 33 E338802000098 Device Info When this sub menu is selected Information about device such as serial number version apllication information device token is displayed on the screen MENU Language 1 Language S NO 337E338802000098 Update Firmware 2 Update Firmware Device Info 3 VERS 04 10 US ZBETHPC Test 4 Test Device Token 342 moettings PIN Code Reader Press BACK Key Load Device Token Load Device Token sub menu should be choosed in settings menu In main menu highlight 5th choice settings using up and down arrow and press enter highlight choice 4 Load Device Token and press enter Details about loading token is described in General features section section 5 VAG Pin Code reader automatically extracts the pin code of the car for VAG group Adapter side is connected to the OBD of the car and the other side is connected to Zed BULL 14 Zed BULL VAG Pin Reader OBD II 1 Choose 6th choice Pin Code Reader from main menu MENU 1 Read amp Identify 2 Clone Chip 3 Manual Programming 4 Test 5 Settings PIN Code Reader 2 Press enter Waiting for Module expression will be displayed on the screen PIN Code Reader WAITING FOR MODULE 3 Plug the Pin reader adapter to the OBD II connector The device will extract the pin code automatically and will be displayed on the screen If extracting i
13. Bull Pc software is for brand Omega Mtrk IC Programmer Omega Mtrk IC Programmer covers all the applications in the list and we suggest this programmer But user is free to use any of the IC programmers in the market According to the features of IC Programmer all the Eeproms and Mcus might need to be desoldered from immo board For most of the IC programmers in the market Eeproms and Mcus must be desoldered from immo board While desoldering the Eeproms and Mcus user must be very carefull since the pins of the Eeproms and Mcus are thin they might be broken if not disoldered slowly and properly When an Eeprom or Mcu is read with IC Programmer we strongly recommend user to save a copy of the original Eeprom or Mcu data file When a problem occurs while using the file copy of the original file will be still holding the needed datas and might be used for recovery The Eeprom or Mcu must be soldered back in the same direction when it is desoldered While soldering back the Eeprom or Mcu user must be carefull against unwanted short circuits between pins While reading motorola Mcus removing the security of the Mcu is suggested If the Mcu is read without removing the security all the 18 informations might be deleted for some Mcu types So user must be carefull about this detail while reading Motorola Mcus Some non original IC programmers in the market might delete Eeprom and Mcu datas while reading Using original IC program
14. Select p Auto Detect y MODE Zei Password Mode Data Coding Select 0 HC A BF Crypto Mode MSO Read Only Mode Select Frequency Mode Zei Manchester Made Biphase Save Load Config C Bevie Token 0 It is possible to edit latest generation transponder hitag 2 with Zed BULL Pc software Pages of hitag 2 transponders can be both read and written with Zed BULL and Zed BULL PC Software Software shows transponder type transponder mode frequency mode transponder pages and transponder configuration bits to the user and can be edited by the user rs d BULL M INMENU EXTENDEDFUNCTIDNS TRANSPONDER PRODUCTION HITAG2 KEY FOB DATABASE DISTRIBUTOR SETTINGS UPDATE SUPPORT CONTACT Lar Model Year Transponder Type Eprom 3 5RL 133 13 93c 46 ACU HA LL amp TL 1333 13 g3c45 ACURA MD 2001 g3c45 ACURA INTEGRA 2000 2001 S3c45 ACURA HS 2001 93c46 ACURA 52 2002 g3c45 ALFA ROMEO BRERA 2005 ALFA ROMED 145 1995 1998 S3c45 ALFA ROMEO 146 1335 1338 93c 46 ALFA ROMEO 147 2000 ALFA ROMEO 155 1395 1335 g3c45 ALFA ROMED 156 1998 2001 S3c5b5 ALFA ROMEO 155 2001 2003 ALFA ROMEO 156 2003 2005 Device Token 0 In transponder catalogue sub menu user finds usefull informations about transponders and matching car models Information about the IC type in immo box of the car is also given
15. X A d 16 Renault Dacia Sagem immobox X A A A A A 17 Renault Siemens A X A A A 18 Fiat Lancia Afa romeo Delphi immobox A A A A A A 19 Peugeot Citroen Valeo immobox X A A A A 20 Toyota Corolla 1998 99 89780 12060RI 3BTY X A X X A 21 Volvo immo3 Bosch immobox X A X A A 28 22 Toyota Corolla Bosch X X X N N 23 Toyota Yaris 2 X A X X N y 24 Toyota Corona X A X X N N 25 Renault Laguna 2 X X A d d N 26 Mercedes Actros Atego Temic immobox X A X d N y 27 Renault Megane 2 X X A d N 28 Afa Romeo Code Bosch immobox A d d N y N 29 Mitsubishi Bosch immobox X X d y N 30 BMW ews X A X d N N 31 BMW ews2 X A X d N y 82 BMW ews3 X X d N y 33 Daily Iveco Truck Bosch immobox A X d y N N 34 Renault Laguna Valeo immobox X A d d N N 35 Afa Romeo Iveco Bosch immobox X X d N N 36 Suzuki Swift X X X y N 37 Toyota Corolla 2000 X X X N X 38 Mitsubishi carisma Bosch immobox X A X d N N 39 Toyota Corolla 2000 20002 Delson X X X N N 40 Nissan Subaru Siemens immobox X A X d N N 41 Peugeot motorbike Marelli immobox X A X d N N 42 Renault Sagem immobox A X d N N N 43 Peugeot 406 Siemens immobox X d d N N 44 Peugeot 206 Siemens immobox X d d d 29 45 Audi Delphi immobox 46 Peugeot Fiat Lancia Citroen Texton immobox 47 Chrysler SKIM immobox 48 Mazda 323 Te
16. e done correctly in order to use the software Choose language and com port Clicking Refresh Port button will show the possible communication ports that Zed BULL using After choosing correct com port click on connect button if connection fails an error message will be displayed if connection is succesfull all buttons will be active In main menu window normal read write operations are done when READ button is clicked the transponder identification is displayed on the software window Writing to transponder is done in 2 steps first the transponder type to write onto is choosen later WRITE button is clicked Transponder informations are added to database after clicking on ADD TO LIST button 16 On bottom left side status bar gives information about the existing process When process is completed the bar becomes totally blue v err 7ed BULL e e TRANSPONDER CATALOGUE KEY FOB DATABASE DISTRIBUTOR SETTINGS UPDATE SUPPORT CONTACT MAIN MENU EX N Yi XTEMDED FUNCTIONS TRANSPONDER PRODUCTION HITAG 1 Opel imma2 Siemens immabos Transponder Fin Code e TTMS370L 702 28 pin 256 Bytes Prepare 11 Temic Transponder 2 Y T d CZD SE d Calculate Programme Transponder J A 16bit Calculate Pin Code Kl HYUNDA S Calculate Pin Code from last B digits of VIN Calculate Fin Cade F
17. en will be loaded to the device If not successfull Pc software will give an error message Invalid Incode then user should check and enter the Incode again connections of Zed BULL are shown in the picture below VAG Pin Reader connection Zed BULL USB Zed BULL Zed BULL Power Switch Interface Power Jack Zed BULL Power Adapter G gf _ PC USB Zed BULL USB PC Interface Cable After Power switch of the Zed BULL is turned on user should put the Security login card on the antenna Unless Security login card is put on the antenna at start up the Zed BULL functions won t work Pressing button RI allows to try logging in again The Security login card is put on the antenna as IN the picture below 7777 Pam 4 W X w CESR Read LOGIN Card 07 If user ooses or has problem with security login card local distributor should be contacted immediately Functions of the key pad buttons are described in the figure below apen bt n B Z wo Hi Read A e gt E Write Back Up mags Enter the functionalities of Zed BULL such as transponder identification transponder cloning transponder production Eeprom and Mcu applications Pc Software are upgradable it is possible to improve fuctionalities of Zed BULL with new developed technologies This menu is used for reading and identifying transponder Transponder ID transponder logic lock status and car type for some
18. ll device in the market Let s take a look what Zed BULL can do It can identify all transponders used in autmotive industry copy all fixed coded transponders copy some of 40 all 41 all 42 unlocked 44 VAG all 45 and all 4D transponders Also it can copy all type of Texas AC transponders to batteryless TPX1 transponder all type of 4D transponders to batteryless TPX2 or Silca Electronic heads It can prepare transponder from EEPROM or MCU datas of car which directly starts the car or ready to match with diagnostic devices It can calculate pin code from EEPROM MCU VIN number or key data of the car for some car models Device is supported with PC software where user can find usefull informations about transponders and matching car models and remote programming procedures Storing unlimited limited with Pc harddrive capacity customer information to database is another advantage of Zed BULL PC Software Zed BULL PC Software also has all functionalities of the device itself such as reading identifying and cloning transponder Zed BULL PC Software is capable of reading and writing to new generation Philips Hitag 2 crypto transponders One of the most usefull feature of the PC Software is transponder production application User can prepare their own transponders such as 11 12 13 4C 33 40 41 42 44 VAG 44 Mitsubishi 45 46 61 62 65 and 73 for diagnostic devices Zed BULL has got token system which is free of charge when
19. mers is suggested While desoldering the Eeprom or Mcu user must be careful about not desoldering the neighbour components on the immo board accidentaly For BMW applications user must be careful about the key number When customer wants spare key the original customer key should be read and the key number should be noted Zed BULL is able to show key number when read In the PC software window proper key number should be selected E seers Ted BULL 9 TRANSPONDER CATALOGUE KEY FOB DATABASE DISTBIBUTOB SETTINGS UPDATE 5 MAIN MENU TRANSPONDER PRODUCTION HITAG2 32 BMY Ew Transponder MCBSHCTTEA8 2D47J 52 pin 512 Bytes Bei Range Rover ID 33 Transponder Type PCF 330 35 REMOTE KET Transponder 1 ready to start the car Programme Transponder Food Calculate Pin Code 0 Calculate 16bit Ela HYUNLAJ L Calculate Pin Code from last 6 digits of VIN Calculate Pin Code Device Token 0 To make key which directly starts the car for the modules 11 12 and 18 few additional steps required The prosedure is as below 1 Desolder the Eeprom or Mcu from immo board 2 Read Eeprom or Mcu with external IC Programmer 3 Save the file with bin or dat extension with any name and to any location as you wish 4 Open the file that you saved using the Zed Bull Pc Software insert the suitable transponder to the
20. mic 49 Suzuki Grant vitara 50 Peugeot Fiat Citroen 51 Toyota avensis 52 Nissan Siemens immobox NATS 4 53 Volvo Bosch immobox 54 Daewoo immobox 55 Opel isuzu immobox 30
21. omer information be stored in database section of the PC software When a customer whose information exists in the database comes again using recorded information it is possible to make key Here user will find contact details of Zed BULL distributors around the world g r e e MAIN MENU E m EXTENDED FUNCTIONS TRANSPONDER PRODUCTION E HITAG2 TRANSPONDER CATALOGUE DATABASE DISTRIBUTOR SETTINGS UPDATE SUPPORT CONTACT Device Information Device Seral Number Software Version Device package information Token Device Information EN Database back up R Back up Load database A F X id Load Token OUTCODE Request Duteode 1 E Mail Adress INCODE send 4 Enter Incode Device Token 0 In this menu user can load token and update the device Loading token Is described in General Features section with details Clicking the button Serial number version user can learn the device serial number and version of the software When user wants to update the device update file is loaded using open file button and selecting the correct update file for the device and Update button is clicked Device starts updating it self The status bar shows the percentage of the process Important note When user wants to update device for additional applications such as Eeprom amp Mcu ap
22. plications or transponder production applications and other applications uploading both ZBP and ZBC file is required When 24 user wants to update Zed BULL for new version only ZBP file needs to be uploaded to Zed BULL User should contact local distributor for ZBC and ZBP files Steps for updating Zed BULL 1 Choose Update Firmware choice in Settings sub menu Update Firmware Device Info Load Device Token 2 The device will be in loader mode The screen display should be as below Zed BULL LOADER V 0 3 UPLOAD ZBC FILE S NO 337E338802000098 Or directly from Pc v veer Zed BULL o MAIN MENU EXTENDED FUNCTIONS TRANSPONDER PRODUCTION HITAG2 softwa re user may click TRANSPONDER CATALOGUE KEY FOB DATABASE DISTRIBUTOR SETTINGS SUPPORT CONTACT Update Mode button to E get the device to loader EE mode Here user should upload ZBC or ZBP file using pc UPDATE PIN READER SOFTWARE software Click open file load ZBC or V ZBP file and finally click update button 3 After uploading ZBC file user may restart the device and end updating or upload ZBP file if updating to newer version is required Device Token 0 LOADING FILE UPDATED UPLOAD ZBP FILE OR RESTART DEVICE Device is restarted turning off the power switch 25 Whenever user has problems or guestions this sub menu can be used An e mail will be sent to the manufacturer
23. s unsuccessfull UNSUCCESSFULL expression will be displayed on the screen 4 If pin reading is unsuccesfull try the steps from 1 to 3 again Zed BULL PC software is used for EEPROM and MCU applications transponder production Hitag 2 reading and writing storing customer information getting informations about transponders and matching car models key fob programming procedures distributor contact details Transponder reading and writing can be both done with or without PC software Software Setup Double click on the setup exe icon and install the software After 15 installing software with the USB cable given connect Zed BULL to PC using any of the USB ports Click on Zed BULL exe to run the software Note to use the software NET framework minimum version 3 5 should be installed in your PC v wink Ted w TRANSPONDER CATALOGUE KEY FOB DATABASE DISTRIBUTOR SETTINGS UPDATE SUPPORT CONTALT MAIN MENU 1 EXTENDED FUNCTIONS TRANSPONDER PRODUCTION mes SI S asas a ul HITAI2 2 Philips PCF 7330731 00 oo oo oo Philips PCF 7835 _ Electronic Head TPE eb ZA v 5 06 5 T5 WRITE ADD TO LIST Model Year Transponder Type 3 BHL 1997 13 ACURA 1999 13 ACURA MD 2001 13 ACURA INTEGRA 2000 2001 ACURA 2001 13 ACURA Ha 2002 13 ALFA ROMEO BRERA 2005 46 Device Token 0 In this menu all settings must b
24. s feature is used The eeprom bytes are written and key data is calculated This calculated data can be written manually to transponder Preparing random data and unlocking 48 megamos crypto transponder is also available in this sub menu Right bottom side is reserved for Hyundai Kia pin code application 20 Hyundai and Kia pin code is calculated from last 6 digits of the VIN For Hyundai calculation is not valid for numbers beginning with O for Kia all numbers are valid v wee Zed BULL www TRANSPONDER CATALOGUE KEY FOB DATABASE DISTRIBUTOR SETTINGS UPDATE SUPPORT CONTALT MAIN MENU EXTENDED FUNCTIONS TRANG HITAG2 T ransponder Type A0 Opel 41 Nissan 42 Vag 44 Mit O 44 ag 45 Peugeot Lar Model Transponder Type 46 O 62 ALFA ROMEO BRERA 2005 46 gt FMi ALFA ROMEO 156 2001 2003 4B ALFA ROMEO 156 SPORT WAGON 2001 2005 46 Key Number _ ALFA ROMEO 159 2005 46 EM AUDI AB 2003 2006 I 7 ALFA ROMEO 166 2004 46 2 BMW 4 C CITROEN C3 2000 2004 Es PROMED SPIDER 2005 45 2 BMW eb5 J PORSCHE CAYENNE CHEVROLET MALIBU 2004 2005 46 BMW e87 O Vw TOUAREG CHEVROLET DAEWOO CAPTIVA 2006 O Vw PHAETON CO PEUGEOT 307 CHRYSLER 300C 2005 46 O CITROEN Picasso 2000 2004 CHRYSLER TOWN amp COUNTRY 2005 46 CHRYSLER VOYAGER 2004 1b CITROEN BERLINGO 2001 46 OSE BLANK PCF7935 Produce Transponder Device Token 0
25. will be successfull but in order to reduce the copying process time these informations should be selected correctly Manufacturer Communication Port Sqlect Select Copy Button Disconnects from server Fed Bull ED BULL CHRYSLER EIRRUS Z LLLI AA Model Year Select Status Bar After informations are selected copy button is pressed Connection test will be done automatically and if it is successfull transponder pages will be read to be send to server The message below will be displayed fed Bull Please take Orginal 4D Transponder off From 2ed Bull antenna After puting Electronic4D or TPxz Transponder to Zed Bull antenna Click OK and please wait Tamam When this message is displayed user must remove the original key from Zed BULL antenna other wise Zed BULL will try to write on to original key and it will cause data corruption with the original transponder server will give approximate time for copy process when user confirm the given time copying process will start fed Bull Waiting Time 30 minute Do vo accept 11 If user wants to end process before it is completed Disconnect button should be pressed After server makes the calculation datas will be written to transponder automatically if user wants to write second or third key write button is pressed to write the datas to transponder Copying process is completed Note To copy 4D transponders user should use a PC which has
Download Pdf Manuals
Related Search