Portable Whole Blood Test System User Guide
Contents
1. 9 For the reflectance test a After applying blood to the electrochemical test strip wipe the finger to remove any blood with a clean piece of gauze b Gently without force apply pressure to the fingertip to accumulate a large drop of blood c Excessive squeezing of the finger may alter test results d Use a pipet or capillary blood collector to apply whole blood to the test strip blood application window e In about 2 minutes the results will appear on the display Remove and discard test strips DO NOT add more blood to any test strip that has been used 31 VII MEMORY Test results are automatically stored in the CardioChek Plus analyzer s memory The analyzer can store up to 50 results of each chemistry and 10 results for control tests The analyzer allows review of the results in order from the most recent to the oldest Each result is displayed with time and date Results stored in memory are not deleted when the batteries are changed How to Review Results Stored in Memory 1 Press either button to turn on the analyzer If the display reads INSTALL MEMO CHIP go to Step 2 If the display reads INSERT STRIP press Enter Press Next until MEMORY is displayed Press Enter CHEM is displayed Press Enter then Next to select the desired chemistry Note Until the chemistry has been run at least once the test name is not displayed Press Enter to view the test result including time and2. See Section lll Setup How to Reset the Language The wrong date and or time is displayed Date and time have not been set correctly See Section lll Setup How To Set the Date and Time FAILED is displayed during a check strip test Analyzer needs to be cleaned Check strip is dirty or damaged Wipe the test strip slot with a clean damp and lint free cloth Use spare check strip If check strip still fails call Customer Service TOO MUCH LIGHT Test is being performed in direct light or outside Test inside away from windows and away from direct lamp light MEMO CHIP ERROR MEMo Chip is defective Use another MEMo Chip from the same lot TEST ERROR Insufficient sample has been Test again with a new test added to test strip strip and make sure the correct volume of sample is used LANGUAGE Analyzer is new or language Follow user guide instructions option has not been set to set language TEST NOT ALLOWED Test selected by MEMo Chip Check MEMo Chip and make installed cannot be run on sure that the correct MEMo your analyzer Chip is inserted Call Customer Service LOW TEMP Analyzer is below acceptable Move to warmer environment operating temperature and test after analyzer reaches proper temperature HI TEMP Analyzer is above acceptable Move to acceptable operating temperature environment and test after analyzer reaches proper
3. to run e Contains the calibration curve and the lot number for the specific test strip lot e Controls test sequences and timing e Provides the measuring range for the test Guidelines for using the MEMo Chip e The MEMo Chip must be inserted to run a test e Use only the MEMo Chip that is included with each package of test strips The lot number code on the test strip vial s MEMo Chip and analyzer display must match e lf the expiration date in the MEMo Chip has passed the analyzer will display EXPIRED LOT e f your MEMo Chip is lost or misplaced please call PTS Inc Customer Service for a replacement Apply blood to ll INTRODUCTION TO THE CARDIOCHEK PLUS TEST SYSTEM continued The MEMo Chip port is located at the top center of A Jh A the analyzer The MEMo Chip is inserted into this port with the finger notch facing up Push firmly but gently until the MEMo Chip is fully inserted Important Be careful not to bend the connector CardioCbe Y Plus Test Strip Test strips are designed for specific analytes A test strip is inserted into the analyzer then blood is applied to the blood application window for reflectance tests or the tip of the test strip for electrochemical tests As previously described the ensuing chemical reaction produces a color change or an electrical current which the analyzer measures and compares to the calibration curve stored in the lot specific MEMo Chip The analyzer conver
4. STRIP v TECHNICAL SUPPORT MEMO CHIP i i i i i i INSTALLED sn amp i Win D POLY T SYSTEMS 1 35 e 03 05 2013 rs H ECH D L H i i USE CODE 1 95 0205 2011 to D oam i t y H nas oxos 20 H i bod P301 i od 0 od A CONTROL RUNCORTROL o oO D mas 03 05 2014 J E a pant i H E D P 1 3 SECONDS i D H 1 bd bo ias mamm UU D I mmm II i H i D H mas 05 30 201 Z i NW 0 HED aT a 7 JI y oi E Fo CLEAR MEMORY H D POLY T SYSTEM i ti 1 1 35 03 05 2014 H i 35 05 2011 aech Lwsi OUND O a A Se T APPLY SAMPLE Q H APPLY enke mas 03 05 2014 ued prepa i i H D 1 35 03 05 2013 U EEN a i b 1 HT vg PS H H mas mmm H Note If the units are locked the UNITS screen does not appear 11 IL SETUP continued i How to Turn Off the Analyzer To turn off the analyzer press both buttons Enter and Next at the same time for three seconds After three minutes of idle time without a test strip or check strip inserted the analyzer will perform a 6 second count down and turn off To stop shutdown press either button You can also remove the batteries to turn off the analyzer Setting Language The first time the analyzer is turned on you will be reguired to set the language date and time The language menu consists of the following choices Eng
5. analyzer or any of the supplies or accessories to high humidity extreme heat cold dust or dirt The analyzer may be stored at a temperature of 50 104 F 10 40 C and 20 80 Relative Humidity RH Do not freeze Do not scratch or damage the surface of the check strip Please read the test strip package insert for storage and handling information that applies to each test strip 35 IX CARE AND CLEANING continued Cleaning Instructions 1 Locate the optical glass within the reflectance test strip slot 2 Open an alcohol wipe prep pad 3 Fold the wipe and carefully wipe the optical glass and test strip guides clean If the area is especially dirty this may require additional wipes 4 Immediately dry the optical glass completely with gauze Make sure the glass is clean dry and completely free from any fingerprints dust or smudges The glass must look clean when held at different angles If the exterior of the analyzer needs cleaning wipe with a damp not wet alcohol wipe or dampen cloth with water or medical grade disinfectant and wipe surfaces and the display area very carefully Be careful not to get the test strip port or slot where the test strip is inserted wet Do not use bleach window cleaner or hydrogen peroxide 36 X TROUBLESHOOTING MESSAGE or ISSUE PROBABLE CAUSE WHAT TO DO Desired language is not displayed Language has been set incorrectly Turn analyzer off
6. dry before testing Warm the fingers to increase blood flow Let the arm hang down at the patient s side briefly to allow blood flow to the finger tips 27 VI RUNNING A TEST continued How to Obtain a Blood Sample 1 2 3 6 7 Clean the finger Be sure the finger is completely dry Use a new sterile disposable lancet to puncture the skin Stick the finger on the side of the fingertip instead of the center See the following picture To get a drop of blood gently apply pressure to the finger starting at the end of the finger closest to the hand and moving towards the tip e lf running an electrochemical test with a reflectance test apply a blood sample to the tip of the electrochemical test strip wipe away any remaining blood with gauze and collect a blood sample for the reflectance test e lf only running a reflectance test lance the finger wipe away the first drop of blood with gauze and use the second blood drop for testing The blood drop should be hanging down from the finger to make it easier to collect the sample with a pipet or capillary blood collector Follow the specific instructions found in the test strip package insert for each test for sample application and volume ranges For reflectance tests use of a pipet or capillary blood collector ensures a sufficient volume of blood has been applied to the test strip Make sure the test strip is inserted all the way into the test st
7. temperature 37 X TROUBLESHOOTING continued MESSAGE or ISSUE PROBABLE CAUSE WHAT TO DO INSTALL MEMO CHIP MEMo Chip is not properly Insert same or new MEMo inserted or is defective Chip properly EXPIRED LOT Test strips are expired wrong MEMo Chip is inserted or date is not set properly Check test strip expiration date and make sure correct MEMo Chip is inserted Check date setting see Section lll Setup How To Set the Date and Time REPLACE BATTERIES Batteries need to be replaced Replace all batteries with new high quality AA batteries The analyzer will not run tests until batteries are replaced TEST ABORTED Test strip was not properly Test again with a new test inserted or was removed strip before test was complete PRINT ERROR Print function has been Print result in MEMORY or interrupted test again Results will not print Communication Cable was improperly connected Printer cover is not closed properly Printer indicator light is red Labels paper were not loaded in the printer Check all connections Reprint test results stored in memory Close printer cover correctly ensuring that the printer indicator light is green Reprint test results stored in memory See Printer System Setup Operating System Instruction Sheet packaged with the printer STRIP ERROR MEMo Chip is defective Use another MEMo Chip from the sam
8. to the values on the Quality Control Range Card included with control materials 13 The control result s will also be stored in the analyzer s memory 14 To exit the control testing menu press Next until EXIT is displayed Press Enter 15 Press Next until RUN TEST is displayed If Ouality Control Results Are Not in Range 1 2 Ensure test strip port area is clean Make sure neither the test strips nor the controls are past the expiration date printed on the label Make sure the MEMo Chip matches the test strip lot Repeat the test again using fresh materials Call Customer Service for assistance 26 VI RUNNING A TEST Blood Testing A package insert is included with each box of PTS Panels test strips Please read the test strip package insert and this section of the user guide completely and carefully before testing Testing Supplies To perform a blood test you need CardioChek Plus analyzer PTS Panels test strips Lot specific MEMo Chip Sterile lancet Pipet or capillary blood collector Gauze or cotton balls Alcohol wipe optional This analyzer requires whole blood for testing Do not operate the analyzer in direct light Reference the Section IX Care and Cleaning section for more information Helpful Hints on Getting a Good Drop of Blood 1 2 Instruct the patient to wash hands in warm soapy water Rinse well and dry completely If an alcohol wipe is used let the finger air
9. 00 a m to 7 00 p m USA Eastern Time using the following contact information Polymer Technology Systems Inc 7736 Zionsville Road Indianapolis IN 46268 USA 1 317 870 5610 Direct 1 877 870 5610 Toll free inside the US 1 317 870 5608 Fax Email inforequest cardiochek com Website http www cardiochek com ll INTRODUCTION TO THE CARDIOCHEK PLUS TEST SYSTEM The CardioChek Plus Test System The CardioChek Plus test system consists of three main parts These include the analyzer PTS Panels test strips and a lot specific MEMo Chip The CardioChek Plus Test System and Operating Principle The analyzer employs both light reflectance and electrochemical biosensor technology to measure an enzymatic chemical reaction When a blood sample is applied to a reflectance test strip a chemical reaction occurs that produces a color change on the test strip When blood is applied to an electrochemical test strip a current is produced This color or current is measured and compared to a calibration curve stored in the lot specific MEMo Chip The analyzer converts this color or current reading into a test result the darker the color or greater the electrical current the higher the analyte concentration The test result appears on the display screen ll INTRODUCTION TO THE CARDIOCHEK PLUS TEST SYSTEM continued D A E F C Display A Display shows test results messages time date and stored resu
10. 27 How to Obtain a Blood EE ul E 28 How to Run a Reflectance Test 29 TABLE OF CONTENTS How to Run an Electrochemical Test 29 How to Run an Electrochemical Test with a Reflectance Test 30 VIl MEMORY aW GR UC FA NAG cen ee 32 How to Review Results Stored in Memonm ANEN 32 How to Clear Results Stored in Memonm Y YYHHHYLLL LLYR RRnn EF FF LLun 33 VI Wi a FFF NG HR FE BR RTH FFAFRIR NADYNT HD PR FAAN AR 34 TE EE 34 Wi Fi Compatibility RF _ _ m r 34 IX CARE AND CLEANING i visisccsscnccesccsscsascessessccatacscacsscccetectecioccisseveisshecteiedssncateesents 35 Storage and Handling WEE 35 date lala a e ennnen annene 37 XI INTERPRETING RESULTS cccccssscssssessssesssssessnsnesenenesenenesenenesenenesenenaeensnaeens 39 XII CLIA INFORMATION WE 40 XIII SPECIFICATIONS Gei RYG Y RAA NR AYRA naaa REEE 41 XIV CONTACT INFORMATION c eccscseeeesseeeeeseeeeseeeeeseeeeeseeeeesseeeeseneeeeseeeenseeeens 42 XV WARH e EE 43 CardioChek Plus Analyzer Limited Two Year Warramtv 43 XVI EXPLANATION OF SYMBOLG ccccseecesseeeeeseeeeseeeeeseeeeessneeeseeeeeseeeeeneeeeens 44 CardioChek Plus Test System Symbols AAA 44 Sal n NF _ rr O OO O ER EF Hy RD RR 45 I INTRODUCTION The CardioChek Plus analyzer from Polymer Technology Systems Inc PTS Inc is intended for in vitro diagnostic use using whole blood samples This point of car
11. CardioChekF Plus Portable Whole Blood Test System User Guide For Professional Use TABLE OF CONTENTS LINO BUG ON E 4 ll INTRODUCTION TO THE CARDIOCHEK PLUS TEST SYSTEM 5 The CardioChek Plus Test EE 5 The CardioChek Plus Test System and Operating Prince 5 The MEMO CHIP cccncituienoithanntindantitdows a ES 7 SEH 9 Battery Use and Replacemenbivicisissicisteceiwcestsscensvereiwearesdansertsatweeresbonscnuesterereraiwess 9 CardioChek Plus Analyzer Menus cccceeeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeeeeeeeeeeeeenaaees 10 How to Turn Off EE 12 Setting Language EE 12 How to Set the Language First Time Usel 12 How to Reset the Language EE 13 How to Set the Date and Time ENEE 13 How to Set the EE 15 How to Set the Sound EE 16 How to Set the Wi Fi On or EE 17 Testing the dE 19 How to Print Results From MGM y scacccccstwisresiwscntss FRYN A UED FRYN FN ARR UD UO 19 How to Get Help and Information Regarding Your CardioChek Plus Analyzer 20 IV CHECKING THE SYSTEM NEE 21 Analyzer Check Eege Eed 21 How to Use the Analyzer Check Gip LL LLYFR YHn FFF FFF Lon 21 V QUALITY CONTROL TESTING ccccseecseseeeeeseeeesneeeeeeeeeeseeeeesseeeesseeeeeseeeessneees 23 Q lity e ed 23 How To Run a Quality Control Test on Reflectance Test Gips 25 How To Run a Quality Control Test on Electrochemical Test Strips 26 VI RUNNING A TES Wess eeh 27 lm B6 Mi EFE NF DE NO YNN eee er eege
12. RT STRIP Note If RUN TEST is displayed go to Step 3 Press Next The display will read RUN TEST Press Next until MEMORY is displayed then press Enter Press Enter to select CHEM or press Next then Enter to select CONTROL Press Next to highlight the test name then press Enter to select LIPIDS for example Press Next to highlight the date time of the test result you want to print Press Enter to print the selected results IL SETUP continued i How to Get Help and Information Regarding Your CardioChek Plus Analyzer 1 2 mb oh 8 9 If the analyzer is off press either button to turn on the analyzer Wait for the display to read INSTALL MEMO CHIP or INSERT STRIP Note If RUN TEST is displayed go to Step 3 Press Next The display will read RUN TEST Press Next until INFORMATION is displayed Press Enter then TECHNICAL SUPPORT is displayed Press Enter to display contact information Press Enter then Next for ABOUT CardioChek Plus display Press Enter to display serial number SN and software version information Press Next to display wireless IP address and SSID if applicable Press Enter to return to ABOUT CardioChek Plus display 10 Press Next until EXIT then press Enter 11 Press Next to return to RUN TEST 20 IV CHECKING THE SYSTEM Analyzer Check Strips A quality control of the analyzer operation can be performed using the gray check strip Two are included in the ana
13. alyzer displays FAILED Clean the CardioChek Plus analyzer test strip slot where the check strip is inserted into the analyzer See Section IX Care and Cleaning Inspect the check strip to make sure it is not dirty or damaged Use the spare check strip and repeat See Section X Troubleshooting in this user guide 22 V QUALITY CONTROL TESTING Quality Control Controls also known as quality control materials are solutions for which an expected analyte concentration range has been established Controls are tested to check the performance of your test system CardioChek Plus analyzer MEMo Chip and PTS Panels test strips Use quality control materials provided by PTS Inc or commercially available quality control materials Refer to the Range Card provided with the controls or visit http www cardiochek com for control specifications Healthcare professionals should follow their facility s guidelines and policies regarding quality assurance and the use of quality control materials Quality control materials should be run whenever a new lot of PTS Panels test strips are received Important Check the expiration date printed on the control bottles Do not use control solutions that have expired For performing a quality control test see the instructions below To perform a control test you need e CardioChek Plus analyzer e PTS Panels test strips e Quality control materials e Quality control
14. ardioChek Plus analyzer by releasing the latch and pulling the door away from the back of the analyzer 2 Remove old batteries from the compartment and properly discard 3 Insert the new batteries into the battery compartment with the positive terminals correctly facing as marked on the inside compartment 4 Replace the battery door To make sure the batteries were installed correctly push either of the two buttons on the front of the analyzer to turn on the CardioChek Plus analyzer Warning Dispose of the old batteries properly IL SETUP continued CardioChek Plus Analyzer Menus The following diagram provides a layout of the menus within the CardioChek Plus analyzer Detailed information on the use of each menu follows Use the following buttons to navigate the menus Enter Button SA Press this button to turn on the analyzer or to accept the current menu choice Next Button ESA Press this button to turn on the analyzer or to advance to the next menu option Note Hold SA and Le down at the same time for three seconds to turn off the analyzer 10 IL SETUP continued CardioChek Plus Analyzer Menus INSTALL Beto CHIP uw TEST 7 HEHORY l mum j SETTINGS INFORMATION i PEs Ei O T ele M i KR H mas 0205 2013 nas osoon H mas 005 2014 H 1 35 0530 201 mas 03 05 2014 mas oosa o H H H ar i 5 eg r i i H ZS a s gt lt a i i v H v H i TECK
15. ause harmful interference to radio communications There is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Wi Fi Compatibility e See Section lll Setup for instructions on turning Wi Fi on and off e Connecting to Wi Fi requires a CardioChek Developer s Kit Contact PTS Customer Service or your local authorized CardioChek dealer for more information Note If unable to run a test wireless communication and patient ID lock may be on You will see a Wi Fi symbol flashing To run a test send a new patient ID to the analyzer turn off wireless communication or press and hold both buttons on your analyzer to override the patient ID lock 34 IX CARE AND CLEANING Storage and Handling Handle the CardioChek Plus analyzer with care do not drop Do not store or operate the analyzer in direct light such as sunlight spotlight under a lamp or by a window Do not expose the
16. date a To recall Control results press Next until EXIT is displayed Press Enter Press Next until CONTROL is displayed b Press Enter when the desired Control test is displayed c For example to review Lipid Panel results from the CHEM display press Next until LIPIDS is displayed then Enter The time and date will be displayed Press Enter when the desired test time and date is displayed Press Next to scroll through results To exit press Next until the display reads EXIT then press Enter Repeat this step until you return to RUN TEST 32 Vil MEMORY continued How to Clear Results Stored in Memory 1 Press either button to turn on the analyzer Wait for the display to read either INSTALL MEMO CHIP or INSERT STRIP 2 Press Enter then press Next until UTILITY is displayed Press Enter 3 Press Next until CLEAR MEMORY is displayed Press Enter to clear memory 4 To exit press Next until the display reads EXIT then press Enter Press Next until you return to RUN TEST 33 VIII Wi Fi Wi Fi Statement This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 1 of the FCC Rules These limits are designed to provide reasonable protections against harmful interference in a residential installation This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instructions may c
17. e POC test system is designed for professional use The CardioChek Plus test system has an optional printer software solutions and wireless communication capability to assist in data reporting The CardioChek Plus analyzer is fast portable and reliable This analyzer is a component of a test system that includes PTS Panels test strips The PTS Panels test strip box includes a lot specific MEMo Chip that contains the assay calibration curve and other important information about the assay PTS Panels test strips are sold separately and are available as single and multiple analyte test strips The test system uses reflectance photometry and electrochemical biosensor technology Reflectance test strips utilize an enzymatic reaction to produce a color change that is detected by the analyzer after whole blood is applied Electrochemical test strips measure an electrical current when whole blood is applied This user guide includes all the information that you need to run point of care assays using the CardioChek Plus test system Before you begin testing please read this entire user guide and the package inserts instructions for use which are included with the PTS Panels test strips Please remember to return the enclosed warranty card to PTS Inc to ensure that you receive product updates and other important information For questions or additional assistance with your CardioChek Plus test system please contact PTS Inc Hours 8
18. e lot INSUFFICIENT Sample size was not large Repeat test s using proper SAMPLE enough to complete testing sample amount s and get result s STRIP REMOVED Test strips were removed during testing Repeat test s without removing test strip s until results are displayed 38 XI INTERPRETING RESULTS All test results must be assessed by a qualified medical professional Depending on the analyte being assessed high or low results may have medical consequences If the result reads gt greater than or lt less than or results are not as expected always repeat the test correctly with a new unused test strip If a test result is displayed that is not expected consult the following table MESSAGE or ISSUE PROBABLE CAUSE WHAT TO DO A displayed result reads lt less than a value Result is below the measuring range of the test Repeat the test Run controls and confirm that controls are in range A displayed result reads gt greater than a value Result is above the measuring range of the test Repeat the test Run controls and confirm that controls are in range Display reads __ __ or N A Result is not available due to a missing value from a calculation or a value is outside the measuring range Repeat the test Run controls and confirm that controls are in range TRIGS TOO HIGH LDL N A Lipid Panel triglycerides test resu
19. in 3 8 cm Weight without batteries 5 5 oz 156 g PTS Panels Test Strips Please read the instructions package insert included with the test strips for information specific to each chemistry Optional CardioChek Printer Power Supply For complete details refer to each printer s user guide 41 XIV CONTACT INFORMATION l Help For assistance with the CardioChek Plus test system please contact PTS Customer Service or your local authorized CardioChek dealer Polymer Technology Systems Inc 7736 Zionsville Road Indianapolis IN 46268 USA 1 317 870 5610 Direct 1 877 870 5610 Toll free inside the US 1 317 870 5608 Fax Email inforequest cardiochek com Website http www cardiochek com 42 XV WARRANTY CardioChek Plus Analyzer Limited Two Year Warranty PTS Inc warrants to the original purchaser only that the CardioChek Plus analyzer shall be free of any defects in materials or workmanship for a period of two years from the date of original purchase Activation of this warranty shall be conditioned upon completion and return of the warranty registration card to PTS Inc If the analyzer becomes inoperative during this time PTS Inc will replace the analyzer with equivalent analyzer at its option at no cost to the purchaser The warranty becomes void if the analyzer is modified improperly installed or operation not in accordance with the user guide damaged by accident or
20. instructions e Quality Control Range Card 23 V QUALITY CONTROL TESTING continued How To Run a Quality Control Test on Reflectance Test Strips 1 Install the correct MEMo Chip for the lot of test strips that you are using Press either button to turn on the analyzer Press Next until the display reads UTILITY Press Enter Press Next until RUN CONTROL is displayed Press Enter Insert the reflectance test strip into the analyzer The CardioChek Plus analyzer will display APPLY SAMPLE This indicates the system is ready for a sample control to be applied Immediately replace the vial cap making sure the test strip vial is closed tightly 6 Remove cap from the quality control material and turn bottle upside down 7 Hold bottle directly over and perpendicular to the blood application window on the test strip 8 Squeeze bottle so that a large drop of control solution is formed 9 Allow the drop of control solution to fall onto the application window of the test strip Do not allow the tip of the bottle to touch the test strip 10 Replace the cap on the quality control material 11 During testing TESTING is displayed Results will be displayed within about one to two minutes 12 Compare the control results to the values on the Quality Control Range Card included with control materials The control result s will also be stored in the analyzer s memory 13 To exit the control testing menu press Next until EXIT
21. is displayed Press Enter 14 Press Next until RUN TEST is displayed If Quality Control Results Are Not in Range ST ee SC Fe 1 Ensure test strip slot area is clean 2 Make sure neither the test strips nor the controls are past the expiration date printed on the label 3 Make sure the MEMo Chip matches the test strip lot 4 Repeat the test again using fresh materials 5 Call Customer Service for assistance 25 V QUALITY CONTROL TESTING continued How To Run a Quality Control Test on Electrochemical Test Strips 1 ST ee Se Fe Install the correct MEMo Chip for the lot of test strips that you are using Press either button to turn on the analyzer Press Next until the display reads UTILITY Press Enter Press Next until RUN CONTROL is displayed Press Enter Insert the electrochemical test strip into the analyzer The CardioChek Plus analyzer will display APPLY SAMPLE This indicates the system is ready for a sample control to be applied Remove the cap from the quality control material and turn bottle upside down Hold bottle near the tip of the test strip Squeeze the bottle so a drop of control solution is formed Allow the drop of control solution to touch the tip of the electrochemical test strip Do not allow the tip of the bottle to touch the test strip 10 Replace the cap on the quality control material 11 Results will be displayed in about 10 seconds 12 Compare control results
22. light ij on Press Enter to select sound or press Next to highlight d off Press Enter to accept the sound choice highlighted Press Next until EXIT is displayed Press Enter to return to SETTINGS O Press Next to return to RUN TEST IL SETUP continued i How to Set the Wi Fi On or Off The CardioChek Plus analyzer wireless communication has been preset to off To turn the Wi Fi to on or off follow the steps listed below 1 lf the analyzer is off press either button to turn on the analyzer Wait for the display to read INSTALL MEMO CHIP or INSERT STRIP Note If RUN TEST is displayed go to Step 3 Press Next The display will read RUN TEST Press Next until SETTINGS is displayed Press Enter Wi Fi is displayed Press Enter The display will highlight A Wi Fi on Press Enter to select Wi Fi on or press Next to highlight lt amp Wi Fi off Press Enter to accept the Wi Fi choice highlighted Press Next until EXIT is displayed Press Enter to return to SETTINGS 0 Press Next to return to RUN TEST o o Nu 2 Oi AWD Note If unable to run a test wireless communication and patient ID lock may be on You will see a Wi Fi symbol flashing To run a test send a new patient ID to the analyzer turn off wireless communication or press and hold both buttons on your analyzer to override the patient ID lock See the Wi Fi Statement section for additional information regarding wireless compatibilit
23. lish ENGLISH Spanish ESPANOL Italian ITALIANO German DEUTSCH French FRANGAIS Portuguese PORTUGUES Dutch NEDERLANDS Chinese rh XI and Russian PYCCKUN How to Set the Language First Time Use 1 Turn on the analyzer by pressing either button Enter or Next 2 The display will read LANGUAGE Press Enter 3 ENGLISH will be displayed Press Enter if English is desired 4 For other languages press Next until the desired language is displayed then press Enter To set the date and time proceed to the How to Set the Date and Time section IL SETUP continued i How to Reset the Language 1 2 4 Turn off the analyzer Press and hold down Enter for approximately 5 seconds during the analyzer power up stage until LANGUAGE is displayed Press Enter Press Enter again to select English or press Next to scroll through the language choices Press Enter to select the desired language that is displayed How to Set the Date and Time 1 ST de ele If the analyzer is off press either button to turn on the analyzer Wait for the display to read either INSTALL MEMO CHIP if a current MEMo Chip is not installed or INSERT STRIP if a current MEMo Chip is installed Note If RUN TEST is displayed go to Step 3 Press Enter The display will read RUN TEST Press Next until SETTINGS is displayed Press Enter then press Next until SET TIME is displayed Press Enter to display the date and the ti
24. lt was 400 mg dL 4 52 mmol L or greater No action needed LDL will not be calculated on samples with triglycerides of 400 mg dL 4 52 mmol L or greater 39 XII CLIA INFORMATION l General CLIA Information US Only Please read before testing 1 CLIA waived Each laboratory or testing site using the PTS Panels test strips MUST have a CLIA Certificate of Waiver or other CLIA operating license before testing To obtain a Certificate of Waiver or any other type of laboratory license call your state health department or PTS Inc at 1 877 870 5610 Toll free or 1 317 870 5610 for an application form CMS 116 Before you start testing carefully read all instructions including quality control Failure to follow instructions including quality control instructions will result in high complexity rating and subject the facility to all applicable CLIA requirements for high complexity testing For complete information including performance please refer to the product specific package insert and user guide CLIA waived for whole blood fingerstick and venous EDTA or heparin testing only 40 XIII SPECIFICATIONS l CardioChek Plus Analyzer Calibration Curve Input from MEMo Chip per test strip lot Batteries 4 AA 1 5 volt alkaline Operating Temperature Range 50 104 F 10 40 C Humidity Range Between 20 and 80 RH Dimensions Width 3 2 in 8 13 cm Length 6 0 in 15 24 cm Height 1 5
25. lts Enter q Button B Press this button to turn on the analyzer or to accept the current menu choice Reflectance Test Strip Slot C The reflectance test strip slot is positioned in the lower front center of the analyzer The reflectance test strip is inserted here with the smooth side facing down MEMo Chip Port D The MEMo Chip port is located at the top of the analyzer USB Port E A port that allows communication with a CardioChek branded printer Next E Button F Press this button to turn on the analyzer or to advance to the next menu option Electrochemical Test Strip Port G The electrochemical test strip port is positioned just to the right of the reflectance test strip slot The electrochemical test strip is inserted here with the arrow facing up and pointing toward the analyzer ll INTRODUCTION TO THE CARDIOCHEK PLUS TEST SYSTEM continued The MEMo Chip Each package of PTS Panels test strips contains a color coded lot specific MEMo Chip The color coded MEMo Chip contains the settings for each test The top of the MEMo Chip has a finger notch The bottom has a label with the test name and lot number Always make sure you insert the MEMo Chip into the port with the finger notch facing up MEMo Chip What does the MEMo Chip do The MEMo Chip contains proper settings for the test strip lot you are using The MEMo Chip e Reads the test strip expiration date e Tells the analyzer which test s
26. lyzer carrying case The check strip verifies that the CardioChek Plus analyzer s electronic and optical systems are functioning properly Each gray check strip is calibrated to read a specific reflectance To perform this verification insert the check strip into the analyzer The analyzer will read the reflectance of the gray check strip and indicate if the reading is within the acceptable range When the check strip is not in use store it in the analyzer carrying case It is recommended that the check strip verification be performed e Daily e lf the analyzer has been dropped e When a result is not consistent with expected results How to Use the Analyzer Check Strip 1 Turn on the analyzer by pressing either button 2 When INSTALL MEMO CHIP or RUN TEST is displayed press Next until UTILITY is displayed Press Enter 3 Press Enter when CHECK STRIP is displayed 4 Hold the check strip at the base and insert the check strip ribbed side up into the reflectance test strip slot when INSERT STRIP is displayed 5 The analyzer should display PASSED along with a checkmark icon If the display reads FAILED see the note at the end of this section Remove the check strip and store it in the analyzer carrying case 6 Press Next until EXIT is displayed Press Enter 7 Press Next until RUN TEST is displayed 8 Press Enter The analyzer is ready to run tests 21 IV CHECKING THE SYSTEM continued Note If the an
27. me which is formatted as YYYY MM DD and HH MM The display will then highlight the year Press Enter to accept the highlighted year or press Next to advance the year Press Enter to select The display will then highlight the month Press Enter to accept the displayed month or press Next to advance the month Press Enter to select The display will then highlight the day Press Enter to accept the displayed day or press Next to advance the day Then press Enter to select IL SETUP continued i How to Set the Date and Time continued 9 The display will then highlight the hour Press Enter to accept the displayed hour or press Next to advance the hour Press Enter to select 10 The display will then highlight the minutes Press Enter to accept the displayed minutes or press Next to advance the minutes Press Enter to select 11 The display will then highlight AM or PM Press Enter to accept the AM PM 12 hour clock format or press Next to switch to the 24 hour clock format 12 Once the clock format has been selected the SET TIME menu will display Press Next until EXIT is displayed and press Enter to return to SETTINGS IL SETUP continued How to Set the Units The CardioChek Plus analyzer may be shipped with preset units If the SETTINGS menu does not display UNITS the analyzer is locked in preset units The units cannot be changed if the system has been locked If your analyzer s units have not been preset foll
28. nalyzers and associated test strips may be covered by one or more of the following patents U S Patent Nos 7 435 577 7 625 721 7 087 397 7 214 504 7 374 719 7 494 818 5 597 532 and D534444 Australian Patent No 2002364609 Eurasian Patent No 010414 Mexican Patent No 267323 South African Patent Nos 2004 4929 and 2006 06561 EP Patent No 0750739 DE FR GB IT Other patents pending Polymer Technology Systems Inc 7736 Zionsville Road Indianapolis IN 46268 USA 1 877 870 5610 Toll free inside USA 1 317 870 5610 Direct 1 317 870 5608 Fax E mail inforequest cardiochek com Website http www cardiochek com MDSS GmbH Schiffgraben 41 30175 Hannover C Germany Copyright 2014 Polymer Technology Systems Inc PS 004561 E Rev 2 4 14
29. neglect or if any parts are improperly installed or replaced by the user Note Removing or loosening screws from the back of the analyzer voids all warranties There are no user serviceable parts inside the case 43 XVI EXPLANATION OF SYMBOLS CardioChek Plus Test System Symbols Age gt gt R A vd Consult Instructions for Use Temperature Limitation In vitro diagnostic medical device Serial Number Manufacturer Catalog Number Authorized Representative in the European Community This product fulfills the requirements of the European Directive 98 79 EC for in vitro diagnostic medical devices Product requires separate collection for electrical and electronic equipment per the WEEE Directive Federal Communications Commission 44 XVII INDEX l AN e dee De E A eii CA EE 9 Blood WS SUG rr O Oe RT 27 Check SID eerst anene EER NIRE E EREE 21 cleaning a CU ee ror enor ern aeey ermne tree 35 CLIA Informati n geed 40 TT Le Cun LL EE 42 Date EN HE 13 HeD oea NY RT D creme meee er ere nett meee er hace men aera ee 42 Interpreting Results aco ea ns wc a enc genau AA HE 39 Is gfe E ele EE 12 EE 32 Quality OMG ee 22 HEEN 12 SOUNA SEMINO E 16 EE 41 EE 44 Festing CEN E 27 MIME SEWING eree a 13 Troubleshooting ee 37 Unts Semino rae ieee cecececnteieien dace ere eetereeteceieneetemee ced 15 ATC 43 The CardioChek brand a
30. nger to the tip of the electrochemical test strip to apply a drop of blood Do not place blood on top of the test strip Do not press the test strip into the finger Blood will be drawn into the strip automatically by capillary action TESTING will appear until the result is displayed 29 VI RUNNING A TEST continued How to Run an Electrochemical Test with a Reflectance Test 1 Insert the MEMo Chip that matches the lot number on both the electrochemical AND the reflectance test strip vials 2 Press either button to turn on the analyzer Remove a single electrochemical test strip from the test strip vial and immediately replace the cap Insert the electrochemical test strip into the designated electrochemical test strip port Remove a single reflectance test strip from test strip vial and immediately replace cap Insert the reflectance test strip into the designated test strip slot The reflectance icon and electrochemical icon will display together For the electrochemical test a Obtain a drop of blood using a lancet per the correct technique b Gently hold finger to the tip of the electrochemical test strip to apply a drop of blood Do not place blood on top of the test strip Do not press the test strip into the finger c Blood will be drawn into the strip automatically by capillary action d Test result will display upon completion of the reflectance test results 30 VI RUNNING A TEST continued
31. ow the steps listed below to change your units to mg dL mmol L or g L 1 If the analyzer is off press either button to turn on the analyzer Wait for the display to read INSTALL MEMO CHIP or INSERT STRIP Note If RUN TEST is displayed go to Step 3 2 Press Enter The display will read RUN TEST 3 Press Next until SETTINGS is displayed 4 Press Enter then press Next until UNITS is displayed If UNITS is not shown on the display the units on this analyzer have been locked and cannot be changed If UNITS appears on the display screen proceed to the next step 5 Press Enter The display will highlight mg dL If mmol L or g L is desired press Next until the desired units are highlighted on the display screen and then press Enter to select 6 The display will then read UNITS Press Next until EXIT is displayed 7 Press Enter to return to SETTINGS 8 Press Next to return to RUN TEST IL SETUP continued i How to Set the Sound The CardioChek Plus analyzer sound has been preset to on To turn the sound on or off follow the steps listed below 1 2 ONAN OD If the analyzer is off press either button to turn on the analyzer Wait for the display to read INSTALL MEMO CHIP or INSERT STRIP Note If RUN TEST is displayed go to Step 3 Press Next The display will read RUN TEST Press Next until SETTINGS is displayed Press Enter then Next until SOUND is displayed Press Enter The display will high
32. rip slot Use the test strip and lancet one time only Dispose of properly Precaution Handle and dispose of all materials coming in contact with blood according to universal precautions and guidelines 28 VI RUNNING A TEST continued How to Run a Reflectance Test 1 2 Insert correct MEMo Chip for the lot of strips in use Insert MEMo Chip with finger notch top side up lot number code facing down Press either button to turn on the analyzer 4 When INSERT STRIP is displayed insert the test strip into the analyzer as far as it will go Obtain a blood drop following the correct technique When APPLY SAMPLE is displayed apply blood to the test strip Refer to each specific test strip package insert for sample volume and sample application instructions Within one to two minutes the results will be displayed Remove test strip and discard The analyzer automatically shuts down after three minutes of idle time with no test strip inserted How to Run an Electrochemical Test 1 Insert the MEMo Chip that matches the lot number on the test strip vial Press either button to turn on the analyzer Remove a single electrochemical test strip from the test strip vial and immediately replace the cap Insert the electrochemical test strip into the designated electrochemical test strip port APPLY SAMPLE icon appears on the display Obtain a blood drop following the correct technique Gently hold fi
33. ts this color reading or electrical current measurement into a test result displayed on the screen Each PTS Panels test strip box contains a package insert that provides instructions for use and information specific for each test Please read the instructions completely before testing window application U lil t P Apply blood l totp DN E Example of a Example of an reflectance test strip electrochemical test strip lll SETUP Battery Use and Replacement The CardioChek Plus analyzer requires four 4 AA 1 5 volt high quality alkaline batteries When to Replace the Batteries The analyzer will give you an indication on the display that the batteries need to be changed When the display reads REPLACE BATTERIES no more tests can be run until the batteries are changed Always replace the batteries with high quality alkaline batteries It is recommended to keep a spare set of batteries on hand To extend battery life remove the test strip as soon as a result is displayed The time date and results stored in memory will not be erased when the batteries are changed When the REPLACE BATTERIES message is displayed replace the batteries with 4 new AA alkaline batteries of the same brand Do not use NiCad or rechargeable batteries Caution Improper installation of batteries can result in decreased battery life or damage to the analyzer How to Install Replace the Batteries 1 Open the battery door on the back of the C
34. y IL SETUP continued i How to Set Up the CardioChek Plus Analyzer for Printing The CardioChek Plus analyzer supports printing on CardioChek branded printers 1 rc If the analyzer is off press either button to turn on the analyzer Wait for the display to read INSTALL MEMO CHIP or INSERT STRIP Note If RUN TEST is displayed go to Step 3 Press Next The display will read RUN TEST Press Next until SETTINGS is displayed Press Enter then Next until PRINT is displayed Press Enter to display PRINT COPIES Press Enter to display icons for one two or three copies Press Enter to select or Next to highlight the desired option Press Enter to accept and return to PRINT COPIES IL SETUP continued i Testing the Printer 1 S SH E E d If the analyzer is off press either button to turn on the analyzer Wait for the display to read INSTALL MEMO CHIP or INSERT STRIP Note If RUN TEST is displayed go to Step 3 Press Next The display will read RUN TEST Press Next until SETTINGS is displayed Press Enter then Next until PRINT is displayed Press Enter then Next until TEST PRINTER is displayed Press Enter and a sample printout will be generated How to Print Results From Memory Note Up to 50 test results per chemistry and 10 control test results can be stored 1 If the analyzer is off press either button to turn on the analyzer Wait for the display to read INSTALL MEMO CHIP or INSE
Download Pdf Manuals
Related Search