ATU-R301 USB User Manual
Contents
1. NULL Encapsulation Modulation Multimode Auto Modulation lt Back Cancel Figure 8 Communication Settings window Note Encapsulation types vary depending upon the application CTC Union Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup 9 The Start Copying Files window will be displayed You may review the current settings and click Customize or Back to change the settings Click Next to accept the current settings a message will be displayed indicating that files are being copied as Figure 9 Start Copying Files y 2 Setup has enough information to start copying the driver files IF you want to review or change any settings click Back or Customize If you are satisfied with the settings click Next to begin copying files Current Settings Service Provider Other Service Provider Hardware Type USB Driver type ATM Annex type 88 Encapsulation RFC 2364 PPPo amp TM NULL Encapsulation Modulation Multimode Auto modulation Yes gt Customize Figure 9 Start Copying Files window 10 For Windows 2000 applications the Digital Signature Not Found window may appear warning that the installation software is not a digitally signed version A digital signature is not necessary Click Yes to allow the installation to continue CTC Union 15 Chapter 2 USB ADSL Modem ATU R301 Installation and Software Set2. connections are possible PVC Permanent Virtual Circuit and SVC Switched Virtual Circuit Several different protocols are used on top of ATM The protocol required in your configuration depends on the equipment deployed by your DSL service provider There are several possibilities 1 Point to Point Protocol PPP Over ATM RFC 2364 PPP provides session setup user authentication login and encapsulation for upper layer protocols such as Internet Protocol The use of PPP makes the modem appear as a dial modem to the operating system Dial Up Networking is used to establish a connection PPP is supported by either the WAN Wide Area Network driver or the ATM driver 2 Bridged Routed Ethernet IP over ATM RFC 1483 This protocol makes the modem appear as a local area network LAN device to the operating system CTC Union 3 Chapter 1 Overview RFC 1577 this is another local area network like protocol for IP address ATM address mapping Point to Point Protocol PPP Over Ethernet RFC 2516 This protocol makes the modem appear as a local area network LAN device to the operating system It allows multiple computer users on an Ethernet to share a common DSL connection to the Internet Three types of device drivers are provided for the ADSL USB modem ATU R301 WAN LAN and ATM Note that all three drivers support ATM protocol In addition the ATM driver works with ATM services that are available
3. easy to follow by users worldwide In order to ensure optimal comprehension the following list provides brief descriptions of the formatting styles used throughout this manual Q Commands Commands are always referred to by using the word click before them These commands are always shown as bold faced words For example click Next click OK or click Cancel Q Names of Windows Dialog Boxes The names of the windows also referred to as dialog boxes that appear on the PC screen are always referred to in quotes For example the Setup Complete window Q Names of Options in Windows The names of options to choose from inside the windows that appear on the PC screen are always referred to in italics For example choose the Yes want to restart my computer now option from the window Notes In some cases preparatory or cautionary information is needed before proceeding onto the next step in an installation process This kind of information is provided in the form of notes which are always referred to in bold faced and italicized letters For example Note To access the Control Panel the driver must be running Also make sure the USB cable is plugged into the modem CTC Union Preface The USB ADSL Modem ATU R301 Manual This manual contains information regarding the installation operation and configuration of the USB ADSL Modem ATU R301 Additionally it outlines the use of the Control Panel Application T
4. in recent Windows operating systems The proper choice of driver depends on the combination of Windows operating system and protocol 1 3 WAN driver this driver causes the modem to resemble a dial up modem Call establishment is performed through Dial Up Networking This driver supports RFC 2364 with PVC connections It can be used with Windows 98 Windows 98 SE Windows 2000 and Windows Me LAN RFC 1483 driver this driver makes the modem appear as a LAN or Ethernet device Connection establishment is automatic This driver supports RFC 1483 with PVC connections Additionally PPPoE is supported It can be used with Windows 98 Windows 98 SE Windows 2000 and Windows Me ATM driver this driver works in conjunction with ATM services provided by Windows Both RFC 1577 and RFC 2364 are supported The ATM driver uses Dial Up Networking to create a PVC or SVC connection to establish a PPP RFC 2364 connection This driver can be used with Windows 98 SE Windows 2000 and Windows Me The device driver choices are summarized in the table below Driver Type Protocol Windows OS LAN RFC 1483 Windows 98 Windows 98 SE Windows 2000 Windows Me WAN RFC 2364 Windows 98 Windows 98 SE Windows 2000 Windows Me ATM RFC 1577 Windows 98 SE RFC 2364 Windows 2000 Windows Me Chapter 1 Overview Features The USB ADSL Modem ATU R301 provides the following features Compliant with Unive
5. indicating the software is being removed 7 The Setup Complete window indicates successful completion of this portion of the updating process click Finish 8 Unplug the USB modem cable 9 Processing will continue with Step 7 of the Software Setup process Please turn to page 11 Step 7 to complete the installation portion of the updating process 18 CTC Union Chapter 5 Control Panel Application Chapter 5 Control Panel Application The USB ADSL modem ATU R301 control panel program provides a quick and easy way to configure and check the performance of the modem and the ADSL connection When open the monitor window updates every 2 seconds 1 There are two methods to access the control panel e From the Control Panel window Start Settings Control Panel double click the DSL Modem icon or e From the PC desktop double click the icon in the system tray Note To access the Control Panel the driver must be running Also make sure the USB cable is plugged into the modem CTC Union 19 Chapter 5 Control Panel Application DSL Modem Physical Link System Info Configuration State No Signal Modulation G DMT Transmit Receive Data Rate kbps Link Status Data Activity Transmitting Receiving Cancel Figure 11 Physical Link window 2 The Physical Link tab of the DSL Modem window Control Panel allows you to review the current state of the US
6. ATU R301 Transmission Unit USB ADSL Modem Operating Manual CTC UNION TECHNOLOGIES CO LTD ABOUT THI PREFACE Table of Contents SIMAN WAL THE USB ADSL MODEM ATU R301 MANUAL 0 CHAPTER 1 AB Ao PROTOCOL AND DEVICE DRIVER FEATURES CHAPTER 2 USB ADSL MODEM ATU R301 INSTALLATION AND SOFTWARE SETUP MODEM HARDWARE INSTALLATION ccccccccceecccccececccceeeeecessceeueeseeeeceeeecueuuseeeeesueeeeueuuaeeeeeueeeeeueeeeeseeenseeees SOFTWARE SETUPS CHAPTER 3 CUSTOMIZING COMMUNICATION SETTINGS 00 17 CHAPTER 4 UPDATING THE USB ADSL MODEM ATU R301 18 CHAPTER 5 CONTROL PANEL 19 CHAPTER 6 SOFTWARE UNINSTALL ccceeseeeeeeeeeeeeeeceee sense seeeesceeesseeseeeeseeeeseeeeeseesaseeeeneeeeseeeeeees 23 CHAPTER 7 TROUBLE SHOOTING 0001 26 About This Manual This manual provides a comprehensive user s guide and installation manual for USB modem ATU R301 It has been organized in such a way to make it
7. B ADSL Modem ATU R301 and connection The green indicator in the Link Status field signifies that a connection has been made This indicator blinks while a connection is being established Individual flashing yellow indicators show the Transmitting and Receiving data activity separately as Figure 11 20 CTC Union Chapter 5 Control Panel Application DSL Modem es Figure 12 System Info window 3 The System Info tab displays the release number of the DSL modem driver the firmware release number and the control panel version that you are currently using as Figure 12 CTC Union 21 Chapter 5 Control Panel Application DSL Modem Physical Link System Info Configuration Modulation G DMT Save Figure 13 Configuration window 4 The Configuration tab offers driver appropriate Modulation Encapsulation and VPI and VCI values If you are using a WAN or ATM driver only the Modulation type will be displayed and may be modified LAN driver applications will be able to view and modify the Modulation type Encapsulation type and VPI and VCI values as Figure 13 22 CTC Union Chapter 7 Trouble Shooting Chapter 6 Software Uninstall Remove the USB ADSL Modem ATU R301 software drivers by performing the following steps Note The USB cable should not be unplugged until after the uninstall process has been completed For Windows 98 applicat
8. e list below If your ISP is not listed select Other Service Provider After making selection click Next to continue To make changes to the communication settings click Customize Other Service Provider Customize lt Back fi Cancel Figure 6 Select ISP window If your DSL service provider is listed and you would like to accept the default values highlight the name and click Next Continue with Step 10 below If your DSL service provider is listed and you would like to change the default values highlight the provider s name and click Customize Continue with Step 9a below If your DSL service provider is not listed select Other Service Provider and click Next Continue with Step 9a below 12 CTC Union Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup a Select the type of driver to be installed from the Select Driver Type window and click Next as Figure 7 Select Driver Type Driver N Dri Figure 7 Select Driver Type window CTC Union 13 Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup b Enter the VPI VCI Encapsulation type and Modulation type from the Communication Settings window and click Next as Figure 8 x Communication Settings Enter your communication settings below These settings are supplied by your service provider Encapsulation RFC 2364
9. ear indicating that the setup process has begun 2 Click Settings from the DSL Modem Installer window 3 The Communication Settings window will be displayed Make the necessary changes to the VPI Encapsulation type and or Modulation type and click Apply 4 The Setup Complete window indicates successful completion of the customization process Select the Yes I want to restart my computer now option remove any disks from their drives and click Finish Your PC will reboot CTC Union Chapter 4 Updating The USB ADSL Modem ATU R301 Software Chapter 4 Updating The USB ADSL Modem ATU R301 Software Once the USB ADSL Modem ATU R301 has been installed updating to a new version of the software is a simple process as detailed below 1 From your PC desktop click Start Programs DSL Modem Configure A notification message will appear indicating that the setup process has begun 2 Click Update from the DSL Modem Installer window 3 message will be displayed asking you to confirm the update click Yes 4 The Select installation location window will be displayed Indicate the location of the Setup files and click OK 5 Since updating the modem software requires removing the old version and installing a new one a message will be displayed informing the user not to unplug the USB modem cable until the uninstall process has been completed Click OK A message will be displayed
10. g of the options will be different for each operating system but the same procedure applies The recommended option will always search for the appropriate driver software 3 For Windows 98 Windows 98 SE and Windows 2000 applications you will be required to specify a location for the new driver software Select the CD_ROM drive option a check will appear in the box next to the selected option with no other options selected and click Next CTC Union 9 Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup 4 For Windows 98 Windows 98 SE and Windows 2000 applications a message will indicate that the system is ready to install the device driver click Next as Figure 3 Add New Hardware Wizard Windows driver file search for the device DSL Modem Windows is now ready to install the best driver for this device Click Back to select a different driver or click Next to continue Location of driver C CHARLESSGS_USB GROOTUSB INF Figure 3 Windows is ready to install driver 5 For Windows Me applications the Select Other Driver window may ask you to select the driver from a list of drivers If asked highlight the root directory identified with GROOTUSB INF the Location column and click OK 6 message will confirm that the device driver software has been installed click Finish 10 CTC Union Chapter 2 USB ADSL Modem ATU R301 Installation and Soft
11. he following chapters are included in this manual Chapter 1 Overview offers a brief description of ADSL protocol and device driver selection and the features of the USB ADSL Modem ATU R301 Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup describes the steps for installing the USB ADSL Modem ATU R301 and details the software installation procedure Chapter 3 Customizing Communication Settings provides detailed steps for altering the ATM Virtual Path ID VPI ATM Virtual Circuit ID VCI Encapsulation type and or Modulation type values previously defined Chapter 4 Updating the USB ADSL Modem ATU R301 Software details the procedure for updating to a new version of the modem software Chapter 5 Control Panel Application describes how to configure and check the performance of the USB ADSL Modem ATU R301 and the ADSL connection Chapter 6 Software Uninstall provides detailed steps for removing the USB ADSL modem ATU R301 software from the PC Chapter 7 Trouble Shooting answers some problems that might be encountered in installation and manipulation Chapter 1 Overview Chapter 1 Overview About ADSL Asymmetric Digital Subscriber Line ADSL technology provides high speed data access across regular phone lines copper wires by making use of previously unused frequency bandwidth above the voice band By placing the ADSL signal above the frequency of the voice s
12. ignal ADSL service is able to coexist on the same line with your telephone service ADSL is asymmetric in the sense that it provides a higher data rate in the downstream receive direction than in the upstream transmit direction Asymmetric operation is ideal for typical home and small office use where files and information are downloaded more frequently than uploaded There are several standard types of ADSL modulation techniques including Discrete Multitone DMT and Carrierless Amplitude and Phase CAP The USB ADSL Modem ATU R301 is capable of supporting the following DSL standards ANSI 1 413 Issue 2 ITU G 992 1 G DMT ITU G 992 2 1 TR 59 and ITU 6 992 Annexes C as applicable Protocol and Device Driver Selection The USB ADSL Modem ATU R301 can be easily connected to a USB port on the PC viaa standard USB cable The USB ADSL Modem ATU R301 is fully software upgradeable so that new features and updates may be added by simply loading a new version of the device driver onto your PC ADSL modems employ ATM Asynchronous Transfer Mode framing ATM is a protocol that divides packets into small fixed sized cells for rapid transmission over high speed networks The ATM protocol allows various types of traffic e g data voice and video to be securely and efficiently carried over the same network ATM is being widely deployed by telecommunications carriers in their backbone networks Two type of ATM
13. ions the cable must be unplugged immediately following Step 6 1 From your PC desktop click Start Programs DSL Modem Uninstall A notification message will appear indicating that the setup process has begun 2 Click Remove from the DSL Modem Installer window 3 Amessage will be displayed asking you to confirm the removal of the USB ADSL modem software click Yes 4 The Information window will be displayed reminding you not to unplug the USB cable until the uninstall process has been completed Click OK 5 Amessage will be displayed indicating the software is being removed Setup Complete The Setup Wizard requires the computer to be restarted Would you like to restart the computer now will restart my computer later Remove any disks from their drives and then click Finish to complete setup InstallShield 6 The Setup Complete window indicates successful completion of the uninstall process Remove any disks from the drives select the Yes want to restart my computer now option by clicking in the circle to the left and click Finish Note The screen for Windows 2000 applications will not ask the user to reboot the system Click Finish to complete the Uninstall process CTC Union 23 Chapter 6 Software Uninstall 7 Unplug the USB cable from the PC Note The USB cable must be unplugged before the system is rebooted For Windows 98 applications the cable
14. must be unplugged immediately as the reboot process was begun in Step 6 24 CTC Union Chapter 7 Trouble Shooting Chapter 7 Trouble Shooting 1 If the LED of PWR is dark Please check is the USB cable connected well is the PC powered on is the PC USB interface workable ifthe LED is still dark please call your local agent for further help 2 If the LED of ACT is flashing indicates the connection of the modem is fail Unplug plug the USB cable to restart the modem When there is a valid connection the ACT LED will remain solid If the LED is still flashing please call your local agent for help 3 Ifthe modem is installed as Modem Hardware Installation of chapter 2 and the followed Software Setup is not finished This indicates the plug and play of your PC does not function well Unplug your ATU R301 and then run setup program from your USB ADSL Modem ATU R301 installation CD Follow the steps of Software Setup in chapter 2 to complete the software installation and then a DSL Installer message will pop up to ask you to plug in the USB cable to the modem CTC Union 25
15. rsal Serial Bus Specification Revision 1 1 USB bus powered an external power supply is not required Supports three device drivers Microsoft NDIS 4 0 WAN Miniport NDIS 4 0 LAN Miniport or NDIS 5 0 ATM Miniport Compatible with all T1 413 G DMT and G lite compliant CO DSLAM equipment as well as the vast majority of deployed CAP RADSL CO equipment Software upgradeable ATM driver supports up to sixteen simultaneous ATM virtual connections Includes a Microsoft Windows control panel monitoring program for configuring the adapter and checking the status of the connection Provides an RJ 11 connector for connection to the telephone line Supports DSL downstream data rates up to 8 Mbps 125 times faster than standard 56K modems Supports DSL upstream data rates up to 1024 Kbps Supports PPP over Ethernet PPPoE clients i CTC Union Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup The following information may be required for software installation Contact your DSL service provider before proceeding with software installation e IP Address Settings the software installation process allows the server to dynamically assign IP Address settings If your application requires static setting of specific address information you will need to know IP Address Subnet Mask for Bridged Ethernet applications only Default Gateway for Bridged Etherne
16. t applications only e Name Server Information the software installation process allows the server to dynamically assign Name Server Address settings If your application requires static setting of specific address information you will need to know Primary DNS Address Secondary DNS Address Primary WINS Address Secondary WINS Address e Type of Driver to be Installed WAN LAN and ATM software drivers are supported Note Required if not using default value e ATM Virtual Path ID VPI Note Required if not using default value e ATM Virtual Circuit ID VCI Note Required if not using default value e Encapsulation type Note Required if not using default value e Modulation type Note Required if not using default value e User Name for PPP applications only e Password for PPP applications only 6 CTC Union Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup Modem Hardware Installation Install the USB ADSL Modem ATU R301 by following these steps with the PC running 1 Insert the rectangular end of a USB cable into the USB port of your PC 2 Insert the square end of the USB cable into the USB port of the USB ADSL Modem ATU R301 Note The USB ADSL Modem ATU R301 will be detected and informational messages will be displayed CTC Union 7 Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup Software Setup Note The software setup process for all supported operating sys
17. tems is described in this section with operating system specific differences noted The USB ADSL Modem ATU R301 should be connected to your PC prior to installing the software No other Windows programs should be running on your PC during the software install process 1 For Windows 98 Windows 98 SE and Windows 2000 applications a window will be displayed indicating that new drivers are required click Next to start the installation procedure as Figure 1 Add New Hardware Wizard Figure 1 New driver required 8 CTC Union Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup 2 window will be displayed which allows you to specify the location of the driver software to be installed Insert the USB ADSL Modem ATU R301 installation CD into the CD drive choose the option that allows the system to search for the best driver for your device by clicking inside the circle to the left of it click Next as Figure 2 Add New Hardware Wizard Windows will search for new drivers in its driver database on your hard drive and in any of the following selected Search for the best driver for your device Recommended Removable Media Floppy CD ROM Specify a location oN Browse Display a list of all the drivers a specific location so you can select the driver you want Figure 2 Specify driver location Note The appearance of the window and the wordin
18. up 11 The Setup Complete window indicates that files have been copied Click Finish to complete the installation as Figure 10 Setup Complete The DSL Installer has finished copying files to your computer In a few moments the DSL Installer will attempt to detect your hardware and complete the installation process InstallShield Figure 10 Setup Complete window Note You may need the Windows CD to complete the installation 12 Windows 2000 applications will display a message indicating that the system must be rebooted for the new settings to take effect Click Finish 13 After informational messages are displayed the System Settings Change window will give you the opportunity to reboot the system Remove all disks from their drives click Yes 14 Windows 98 WAN and ATM applications will ask you to provide telephone number and location information when the PC has rebooted Enter the information and click Close NOTE If it is necessary to change TCP IP settings please refer to the user manual of your PCs windows operation system 16 CTC Union Chapter 3 Customizing Communication Settings Chapter 3 Customizing Communication Settings Once the USB ADSL Modem ATU R301 and software have been installed the communication settings may be easily updated by performing the following steps 1 From your PC desktop click Start Programs DSL Modem Configure A notification message will app
19. ware Setup 7 The Welcome window provides an opportunity to quit the setup process to exit all Windows programs before continuing If the Windows programs were previously closed click Next as Figure 4 72 Welcome to the DSL Modem Setup program This 5 program will install the DSL Modem on your computer It is strongly recommended that you exit all Windows programs before running this Setup program Click Cancel to quit Setup and then close any programs you have running Click Next to continue with the Setup program WARNING This program is protected by copyright law and international treaties Unauthorized reproduction or distribution of this program or any portion of it may result in severe civil and criminal penalties and will be prosecuted to the maximum extent possible under law Cancel Installshield Figure 4 Welcome window Note If you quit this process run setup exe from the CD ROM to resume the installation 8 The Select ISP window allows you to specify your DSL service provider A list of service providers is displayed Default values for the Type of Driver ATM Virtual Path ID VPI ATM Virtual Circuit ID VCI Encapsulation type and Modulation type are provided for each DSL service provider listed in the window as Figure 6 CTC Union 11 Chapter 2 USB ADSL Modem ATU R301 Installation and Software Setup Select ISP Select your ISP from th
Download Pdf Manuals
Related Search