Home

K2 GSM Security Alarm User Manual V1.0

image

Contents

1. Communication protocol GSM PHASE 2 2 include data service Wireless Zone 16 can accept one learning code wireless detector in each zone and accept unlimited PT2262 2272 fixed code wireless detectors in each zone Remote Control 3 Wireless Frequency 433Mhz Wireless Distance 100m in open air Backup Rechargable Battery 3 7V 900 1200mAH lithium batteries Net Weight 0 50Kg 10 Warranty 1 This system is warranted to be free of defects in material and workmanship for one year 2 This warranty does not extend to any defect malfunction or failure caused by abuse or misuse by the Operating Instructions In no event shall the manufacturer be liable for any alarm system altered by purchasers 11 Affix Table Table 1 K2 Installation Schedule Before install the K2 please write down the installation plan firstly it is very useful for saving your test and installation time After installed successful then tear down this Schedule for review in further Ee ee ee eee ESM SMS Alarm amp Dialer GSM SOS Call System K2 Installation Schedule Attr SMS Alarm Content Attr eenscr PacelEg ssi a ewer fo fe wesen 2 S wesen 2 fe wisesznesawmi 2 Fs wrcwszonesawm 2 YT ft wiseszoesaom 2 a fo wesen 2 pte wieeszneonem 2 fe wesen 2 weesen 2 aie ee Alarm soeone Water Leakage Alarm a fe a ee psf Panic Help Alarm Emergency Silent Alarm K2 Authorized Number Schedu
2. gt Based on the GSM communication network no distance limitation Ee ee ee eee CSM SMS Alarm amp Dialer GSM SOS Call System 5 Installation and Connection Diagram 5 1 Inserting the SIMCard Important Make sure to switch off K2 Panel before inserting or removing your SIM card 1 At the backside of the panel please remove the cover and Slide the SIM card holder in the direction of OPEN and insert the SIMCard See below photos 2 Close the SIM card holder and then slide it in the opposite direction of OPEN to lock it See above photo 5 2 Contacting the Siren hooter The user can connect one 9 12V rated siren or hooter to the K2 Panel s siren output once alarm occurrence this output ports will start the siren or hooter to make sounds The positive of the siren connect to the Siren port and the negative of the siren contact to the Siren port Generally the siren wire marked red color and black color the red color is positive and the black color wire is negative See below 5 3 Contacting the AC DC Power Supply Please contact the 12VDC to the K2 Panel the Positive of the 12VDC connect to the PWR the negative of the 12VDC please contact to PWR Generally the red color from the AC DC Adaptor is Positive and the black color is negative The AC DC Adaptor is 12V1A or 12V2A see above mentioned Ee eee eee CSM SMS Alarm amp Dialer ESM SOS Call System 5 4 Switching
3. amp Dialer GSM SOS Call System 1 Writing Installation Schedule Please write down your schedule in below table it will make you clearly what sensor in which zone and with what attribute e g using a wireless door contact for entrance using the photoelectric beams for wired zone in outdoor fence and using a wireless smoke detector for fire alarm and so on Please see the Affix table 2 Read the Switch Combination Zone Number Corresponding Table The K2 with fixed switch combination positions for different wireless detectors and wireless remote controls please see Switch Positions Zone Number Corresponding Table Structure and Switch Combination Remote Control Corresponding Table Switch combination Zone Number Corresponding Table Zone Switch Position 4 8 Number SWTICH4 SWTICH5 SWTICH6 SWTICH7 SWTICH8 Notice The value in the table for each zone corresponding the position of the switch 0 stands for OFF side 1 stands for ON side Ot aw a ag EF a es 1 o el So the 01 zone should setup as UN En FTELALALLI E i ee O 7 amp the 02 zone should be setup as The 15 zone should be setup as ON we 1 8 SAT Gere Switch combination Remote Control Corresponding Table Switch combination Remote Control Corresponding Table Serial Switch Position 2 3 Number SWTICH 2 SWTICH 3 The value is same as above mentioned So 01 should be setup as CSM SMS Alarm amp Dialer GSM SOS Call Syst
4. occurrence gt Learning code more safe and easy to add new wireless remote keys and wireless detectors gt Supports 16 Wireless Zones can accept one learning code wireless detector in each zone and accept unlimited PT2262 2272 fixed code wireless detectors in each zone gt Supports verity programmable zone attributes includes Away normal At House or Stay Entrance Zone 24 Hours Sound Zone 24 Hours Silent Zone Local Zone SOS Zone Door Bell Zone gt The SMS Alarm Content of each zone is programmable by user through SMS Commands gt Supports 3 Remote Keys each Remote Key includes one SOS Panic Button for emergency condition to ask for help gt Supports Armed delay to give enough time to leave the home the delay time is programmable by user gt Supports Alarm Delay to give enough time to Disarm it when you come back home the delay time is programmable by user gt Equips one siren output for sounding while alarm occurrence to warning gt The external AC power failure amp recovery alert function supports 2 optional Immediately Send SMS to user after 30 minutes if not recovery then send SMS to user gt Standby internal large capacity rechargeable battery which can standby upto 8hours after AC Power failure also can provide power to wired siren after AC power failure gt Secure Using caller ID for identification unknown callers are ignored gt Supports Password to increase the security of the whole system
5. Meanwhile the K2 will enter to previous status 2 Only the zone attribute code setup as 0 1 2 3 4 will cause the siren sound while alarm occurrence And the siren will sound about 20 seconds then interrupt about 2 seconds the time according to the setting 3 Once any zone triggered the corresponding LED will always on till Disarm or Restart the K2 8 1 Operation by Remote Controls Press the button i on the remote key or Press the wireless or wired Arm button the K2 enters arm status delay time according to the setting Under this status any detector triggered the K2 will alarm if answered the call the siren will stop and can listen in the alarm area by phone If you use the remote control to arm the K2 you press the Arm Button then press the SOS button within 2 Seconds the K2 will enter Armed mode immediately no delay Press the button mi on the remote control or press the wireless or wired Disarm button or access control and RFID Card Reader with authorized access signal the K2 disarms immediately Under this status any detector triggered the K2 will not alarm Except the zone attribute is the 24 Hour Emergency Zones Press the button on the remote control or the wireless or wired Stay button the K2 enters Stay Partial Armed status the zones attribute had been set as outer zone and 24 hours emergency zone triggered will cause alarm but the zone attribute had been set as inner zone triggered will no
6. by the digital number 6 While setup phone numbers please try to plus the country code or remove country code E g 0086 13500001111 or 135000011117 7 Please write down the setting list in a paper for review in further please see the affix table at the last page and tear down from this instruction for review 8 Ifthe command is incorrect the K2 will return Or other warning message So please check the Command or check the input is in ENGLISH INPUT METHOD and CAPS LOCK If the password incorrect will not return any SMS 9 When power on the K2 will alert Di sound once and all zones LED will turn on once then the LED which registered wireless sensor already will turn on once more 10 If more than 2 minutes the GSM Simcard still register the GSM Network failure the buzzer will make Di once and every 10 seconds detects the SIMCARD registering status and failure will alert by D once till restart or switch off 11 Ifthe communication between the MCU and GSM Module failure the buzzer will make DiDi twice to warning every 10 seconds till switch off or restart 12 If detect the K2 hasn t inserted SIMCard the Buzzer will only make once di sound to alert And will not detect the SIMCard again CSM SMS Alarm amp Dialer GSM SOS Call System 13 When alarm occurrence and in the delay alarm time the buzzer will alert by DiDi sounds once the delay timeout the buzzer will stop to sound 14 Reset the K2 wi
7. on off the K2 Panel After finished all of the connections please plus the AC DC Adaptor to external AC Power socket and switch the PSW Switch to ON side to switch on the K2 Panel See abovementioned 5 5 Amounting the K2 Panel The K2 Panel should be installed in a place where the intruders cannot discover it And the GSM Signal covered well Also the user can see the LED easily to know what happened and what is the status of the K2 Panel 6 Settings The K2 is an advanced multifunctional programmable controller The user can program it by SMS Commands for various application requirements 1 The default Password is 1234 2 All the settings are through SMS commands please edit the below SMS commands in your cell phone then send to the K2 Tips The K2 cannot support PIN Code Protected SiMCard Please ensure you have disabled the PIN Code of the SIMCard otherwise can not register GSM Network successful 3 You can program the GSM Alarm amp Dialer K2 with SMS commands using your phone It is safe to do so because in addition to the fact that other people may not know the number of the SIM inserted in it we also use a Password that makes it impossible for anybody who doesn t know it to access the system by chance 4 Remember that commands must be CAPITAL LETTERS It is PWD not pwd CAP not Cap etc Don t add spaces or any other character 5 The pwd in the commands is means the password when you use it please in stand of it
8. 30minutes 01 99 minutes Siren Response to Arm Operation owd ON Default Siren NOT Response to Arm P owd OFF Operation l 00 99hours default is 00 Automatically report Status function pwd T xx means disabled 7 Setup Authorized number a 7 The End
9. 34 then please send 1234D00 0 D01 1 D02 4 D03 6 D08 94 6 8 Inquiry the Zone Attribute If send successful will return the zone attributes 00 1 01 0 02 2 6 9 Setup the Siren Sound time Default is 180seconds If setup successful will return Siren ON xxx Seconds E is the identification character of this command Xxx 000 999 unit is second 3 digits Default is 180 seconds E g if you want to setup the siren sound 60seonds when alarm occurrence and password is 1234 then please send Tips Only the zone attribute code setup as 0 1 2 3 4 will cause the siren sound while alarm occurrence And the siren will sound about 20 seconds then interrupt about 2 seconds 6 10Setup the Alarm Delay Time Default is O00second If setup successful will returniAlarm Delay xxx Seconds F is the identification character of this command Xxx 000 999 unit is second 3digits Default is 000 second Tips Only the zone attribute code setup as 1 2 3 will delay to cause alarm while alarm occurrence CSM SMS Alarm amp Dialer GSM SOS Call System 6 11Setup the Arm Delay Time Default is 30seconds If setup successful will returnAArmed Delay xx Seconds G is the identification character of this command Xxx 00 99 unit is second 2digits Default is 30 seconds Tips 1 Only the zone attribute code setup as 1 2 3 will delay to enter into Arm mode when Arm the K2 2 If Armed the K2 by remote control after press
10. 99 minutes will send SMS Power Goes off 01 99minutes to all authorized numbers or send SMS IAC Power Goes ON when AC Power goes on If the AC Power goes off less than 01 99 minutes then goes on will not send SMS If setup successful will returni AC Power Goes off Send SMS After 01 99minutes 6 15Setup Siren Response Feature to Arm Operation as ata system CSM SMS Alarm amp Dialer ESM SOS Call System Xx ON or xx OFF Default is off Xx ON stands for when armed the K2 by remote control successful the siren will sound 2seconds If setup successful will return Set Ok Xx OFF stands for when armed the K2 by remote control successful the siren will NOT sound If setup successful will return Set Ok if armed or disarmed by phone call or SMS the siren will not make sounds to response 6 16Setup Automatically report Status function XX 00 99 unit is hour stands for the interval time to report the K2 status to the first SMS Alert Number default is 00 means disable report function If no SMS number this function will be invalid The return SMS is the same as by 8 4 Inquiry Status and GSM Module IMEI Code 6 17Reset the K2 Panel to Factory Default The K2 Panel can be reset to the factory default by following operation Switch off the K2 Panel then press the UP and Down Button at the same time See below Switch on the K2 Panel about 3Seconds later the K2 Panel will make sounds to alert then loose the RESET butt
11. GoM Security Alarm GSM SOS Call System An Advanced Programmable Multifunctional GSM Auto Dialer GSM Alarm Panel In The Worldwide User Manual Ver 1 1 Date Issued 2013 02 01 All rights reserved ESM SMS Alarm amp Dialer GSM SOS Call System index 1 Brief introduction 6 12Enable to Alert the first Authorized Number 10 2 Safety Directions 6 13Required the K2 callback 3 Standard Packing list 6 14Setup External Power Status Alert Feature 4 Mainly Features 6 15Setup Siren Response Feature 5 Installation and Connection Diagram 6 16Setup Automatically report Status function 5 1 Inserting the SIMCard 6 17Reset the K2 Panel to Factory Default 5 2 Contacting the Siren hooter 5 3 Contacting the AC DC Power Supply 7 Zone Settings 5 4 Switching on off the K2 5 5 Amounting the K2 8 Operating Instructions 6 Settings 8 1Operation by Remote Controls 6 1Setup New Password 8 2Armed or Stay WITH a FREE call 6 2Setup Authorized number 8 3SMS Commands for Arm or Disarm or Switch 6 3lnquiry the Authorized number On Off Siren 6 4Remove the Authorized Number 8 4Inquiry Status and GSM Module IMEI Code 6 5Modify the SMS Alarm Content 8 5Android Apps Instructions 6 6Inquiry the SMS Alarm Content Setting 8 Technical specifications 6 7Setup the Zone Attribute 9 Maintenance 6 8Inquiry the Zone Attribute 10 Warranty 6 9Setup the Siren Sound time 11 Affix Table 6 10Setup the Alarm Delay Time Table 1 K2 Panel Installation Schedule 6 11Set
12. ck to OFF Meanwhile please switch off the wireless detector otherwise will alert by Di Di two sounds after you switch the switch back to OFF If before switch the switch to OFF then alert by Di Di two sounds then means the operation failure please switch them back to OFF then retry again Switching the other switch combinations from OFF to ON one by one to learn the wireless detectors to other zones Notice a Remote Control and Wireless Detectors activated method For remote control press any key then can activate it no need to press all of them The wireless door contact can be triggered by dispatch the two parts when installed battery inside The wireless PIR Motion Detectors can be triggered by pass though its front when switched on The wireless panic buttons can be triggered by press its button The wireless gas leakage or wireless water leakage and wireless smoke detector equips Test Button press the Test Button then can trigger them The other wireless detectors please reference its user instructions ee eee Eee CSM SMS Alarm amp Dialer GSM SOS Call System b When the wireless PIR Motion detection is PIR 100B please remember setup the PIR 100B to Test Mode while learning to the K2 after learned to the K2 then please setup to Normal Mode by change the Black PIN Jumpers in the PCB please see the PIR 100B user manual c The differences of PIR Motion Curtain Motion and Ceiling motion detector are the det
13. ection direction areas d When the wireless Detectors is PT2262 fixed IC code please setup its wireless code by use some Jumpers to configured it randomly recommend 4 6 jumpers see below 1 Removing the back cover carefully 2 Locate the IC boards black jumpers labeled AO A7 and DO D3 please see below figure 3 Configured the AO A7 and DO D3 different from each wireless detectors If configured the AO A7 and DO D3 are the same the system will treat them as the same one sensor So if you want to add more than one wireless detector to any zone please configure the jumpers as the same in the wireless detectors 4 Also please check the Resistors value is 3 3M Ohm there re 3 Jumpers 1 5M 3 3M and 4 7M if you select incorrect value the wireless distance usually very short or cannot learn to the K2 L N 0 H N 1 L N H 2 am ame amn m n m O 5 Removing wireless accessories After learned the wireless accessories to the K2 it can be replaced by learning a new wireless detector to its position to in stand of it If you want to remove the wireless detector in specified position then please reset to remove all wireless detectors and re learn the other wireless detectors again 6 Some popular wireless detectors i PIR Motion Detector Dual Element PIR Motion Detector Ceiling PIR Motion Detector Door Contact GoM SMS Alarm amp Dialer ESM SOS Call System f mm fe w Door Contact Garage Door Contac
14. em 03 should be setup as 3 Enter Leaning Mode Please press the Learn button and switch on the K2 after switch on the K2 will alert Di once then after enter learning mode will alert Di Di two sounds total 3 Di sounds about 5 Seconds it being learning mode then loose the button The learning Button under Pressed status before switching on the K2 till heard total 3 Di sound The LED of each zone which registered wireless detector or remote control or button will turn on Learn 1 The K2 cannot exit the learning mode automatically must switch off the unit then switch on again to enter the normally mode The Switch Combinations for each zone must be active by at least one switch to learning mode by switch the buttons from OFF to ON and after learned the correct detector into this position please switch the button back to OFF otherwise the zone will in learning mode all the time 2 When learning one detector to the K2 the other wireless detectors must be in OFF status otherwise will confuse the learning operation 4 Learning the Wireless Detector or Remote Control to K2 When the K2 in the learning mode then switch the corresponding switch combinations from OFF to ON one by one and trigger the wireless detector see Notice the K2 will learn the code from the wireless detector automatically When alert by long Di sounds means the wireless detector was learned to the zone position please switch the switches ba
15. le SIMCard Number in the K2 Authorized Type Phone Number Alert when Alarm Occurrence AccesstheK2 SMS amp Call Stay Arm Serial Number Notice Please mark V if for enable and X for disable ESM SMS Alarm amp Dialer GSM SOS Call System Table 2 K2 Program and Operation SMS Command List K2 SMS Command List Caps Lock Function Description Arm Away 1234AA Password is 1234 Disarm 1234BB Password is 1234 Switch On The Siren 1234CC Password is 1234 Switch OFF the Siren 1234DD Password is 1234 Inquiry Status GSM Signal IMEI 1234EE Password is 1234 Setup New Password 1234P6666 owd Serial Number A Function 1 Code Function 2 code Telephone Number See 6 2 Inquiry the Authorized number owd A Remove Authorized Number Modify the SMS Alarm Content owd B ZoneNumber SMS TEE G Alarm Content breaking the windows Inquiry the SMS Alarm Content pwd B Zonenumber 1234B01 Setup the Zone Attribute pwd D Zonenumber Attribute Code See 6 8 Inquiry the Zone Attribute owd D Setup the Siren Sound time owd E xxx 1234E060 Default 1 80S Setup the Alarm Delay Time pwd F xxx 1234F999 Default 000S Setup the Arm Delay Time pwd G xx 1234G09 Default 30S Enable Alert the 1 Authorized No pwd H Disable Alert the 1 Authorized No pwd J Default Required to callback owd K AC Power Goes OFF Alert atonce pwd M 00 AC Power Goes OFF Alert after l owd M xx Default is
16. ll alert by a 2seconds Di sound by the buzzer 15 After you reset or learning remote control or wireless sensors please remember to restart it otherwise can not work proplerly 16 The SMS commands that you will certainly use in the GSM Alarm amp Dialer K2 are the following 6 1 Setup New Password if successful the unit will return new password This is the New Password please remember it The password is 4digits For example the original password is 1234 you want change it to 6666 then you can send the command below 6 2 Setup Authorized number lf you GSM Operator use different number format for SMS and Dial out then please see Notice 6 must setup as includes country code and not includes country code two formats Serial Number 1 6 A is the identification character of this command Function 1 Code 1 2 3 It is for alarm receiving attribute setting 1 stands for when alarm occurrence the K2 will dial as well as send SMS to this number The SMS Number Format must be the Same as the Dial Number Format include or not includes Country code 2 stands for when alarm occurrence the K2 only send alarm SMS to this number doesn t dial 3 stands for when alarm occurrence the K2 only dial this number doesn t sends SMS Function 2 Code 1 2 3 It is for accessing K2 attribute setting 1 stands for when this number dial to the K2 will be rejected after the first ring meanwhile the K2 will be changed to Sta
17. mp Dialer K2 is an Ultra Version of GSM Alarm includes multi functions and ultra low cost and high reliability special for Residential areas business area commercial area office factory industrial area and other Varity applications It integrated high performance GSM Module and MCU inside and with innovative and experienced functions and features to meet the required and potential demands in the worldwide markets The user can receive SMS Text and calling from the K2 once the alarm occurrence immediately Also the user can remotely armed or disarmed and switch on or off the siren by SMS Commands or remotely switch the K2 to arm or disarm with free call from mobile phone or remotely call in the K2 to two way voice combination or send SMS Command to request the K2 call back to create two way voice communication Moreover the K2 supports Android Apps and iOS though the Android Apps the user can quickly to Arm Disarm Inquiry Status and Switch ON or OFF Siren armed or disarmed with free call no need to program the SMS commands every time The K2 equips 1 Big SOS button this button can be programmed as SOS armed stay disable functions 2 Safety Directions Safe Startup Do not use K2 when using GSM equipment is prohibited or might bring disturbance or danger Interference All wireless equipment might interfere network signals of K2 and influence its performance Avoid Use at Gas Station Do not use K2 at a gas station Powe
18. on means the reset operation successful And please restart the K2 Panel again RESET Learn After this operation all the registered wireless detectors and wireless panic buttons and Remote Controls will be removed from the K2 Panel and all of the settings will be reset to the factory default 7 Zone Settings 7 1 Registering the wireless sensor remote control wireless buttons to the K2 a After registered the wireless sensor remote control or wireless buttons must restart the K2 b After your registered a wireless sensor or remote control or button to the position must switch back the DIP to OFF Side except the 1st position c The package wireless detectors registered in the K2 already no need to relearn it again The K2 is learning code more safe and easy to add new wireless remote keys and wireless detectors it supports 3 remote controls and 16 Wireless Zones it can accept one learning code wireless detector in each zone and accept unlimited PT2262 2272 fixed code wireless detectors in each zone The K2 integrated verity programmable zone attributes includes Away normal At House or Stay Entrance Zone 24 Hours Sound Zone 24 Hours Silent Zone Local Zone SOS Zone Door Bell Zone The SMS Alarm Content of each zone is programmable by user through SMS Commands Please follow below step by step to learning the wireless detectors or remote controls or wireless buttons to the expected zones Ee eee a CSM SMS Alarm
19. or office When come back the home or office will delay 20 seconds to alarm in order CSM SMS Alarm amp Dialer GSM SOS Call System to the user can change it to Stay or Disarm the K2 1 stands for outer zones in Armed or Stay mode when triggered will cause alarm 2 stands for inner zones in Stay mode if triggered will not cause alarm in Armed mode if triggered will cause alarm 3 stands for spot alarm zone in Stay mode if triggered only cause the siren to sound Neither dial out nor send SMS out in Armed mode if triggered will cause alarm 4 stands for 24hours emergency zone with sounds In any mode if triggered will cause alarm immediately with siren sounds 5 stands for 24hours emergency silent zone In any mode if triggered will cause alarm immediately the siren will not sound 6 stands for Armed Button trigged it to make the K2 change to Arm Mode 7 stands for Stay Button triggered it to make the K2 change to Stay Mode 8 stands for Disarm Button triggered it to make the K2 change to Disarm mode 9 stands for door bell button triggered it to cause the buzzer to sound 8times Tips 1 When the attribute code setup as 6 7 8 9 the siren will not sound 2 More than one zone attribute can be setup in one SMS Command but don t exceed the SMS character limitation e g if want to setup the attributes of wired zone 01 wireless zone O2wireless zone 03 wireless zones 08 wireless zone the password is 12
20. r off K2 when it near fuels or chemicals Power it off near Blasting Places Please follow relevant restrictive regulations Avoid using the device in blasting places Reasonable Use Please install the product at suitable places as described in the product documentation Avoid signal shielded by covering the mainframe Use Qualified Maintenance Service Maintenance can be carried out only by qualified maintainer ESM SMS Alarm amp Dialer ESM SOS Call System 3 Standard Packing List a a GSM Alarm Panel tt Wireless Door Contact 1 Wireless PIR Motion Detector 1 Remote Control 1 AC DC Adaptor oo o User Manual Optional Accessories wireless detectors PIR Motion Sensor Glass Break Sensor Magnetic Window Sensor Temperature Sensor Vibration sensor Siren ACIDC Adaptor _ a 4 Mainly Features gt Supports Away Armed Partial Armed At House or Stay or Disarmed by Remote Control Wireless Buttons Wired Buttons SMS Commands Call in with free charge Android Apps apps gt Supports 6 Authorized Numbers each number can be setup as receive SMS or receive call or both of them also each number can be setup authorized to call in to listen or call in to arm or stay the system gt Supports 2 way vioice communication through internal sensitive microphone and speaker and call back according to SMS request gt Automatically send SMS Alert Alarm Message and dial to the authorized numbers when alarm
21. t cause alarm Press Emergency button SOS P on the remote control The K2 will cause emergency alarm The siren will not sound but will alert the pre set phone number immediately The Alarm SMS Content is Remote Key SOS Help The Alarm SMS Content for the remote control SOS button can not be modified 8 2 Armed or Stay WITH a FREE call from authorized phone The K2 supports armed or Stay by a free call from authorized phone after you setup the authorized number Function 2 Code as 1 then the user can use this phone number to Arm or Stay the K2 by free charge call in Please reference 6 2 Setup Authorized Number to setup it When the K2 in Disarmed mode any number with the authorized right call in will change it to Stay mode When the K2 in Stay Mode any number with the authorized right call in will change it to Armed Away mode and return SMS confirmation Armed When the K2 in Armed Away Mode any number with the authorized right call in will change it to Stay E T ESM SMS Alarm amp Dialer GSM SOS Call System Mode This function is very useful while you leave or come back home 8 3 SMS Commands for Arm Away or Disarm or Switch On Off Siren The User can Arm Disarm Switch on or off the siren by sending SMS to the K2 The SMS Commands are below INoticejThe system will carry out the commands immediately with no delay after the K2 receive this SMS command 8 3 1 Armed Away Example 1234AA 0 0 04 VAN
22. t Fall Down SOS Button Microwave Dual PIR Detector li WWW Gas Leakage Detector Smoke Detector 4 a lt Necklace Waterproof Panic Button Emergency Button Wireless Signal Repeater 8 Operating Instructions Tips 1 The user can arm disarm Stay Partial armed by Remote Control SOS Button Wireless Button Dial in and SMS Another the user can switch on or off the Siren by SMS Commands 2 Mode explanation Armed Away In this mode any detector triggered will cause alarm It be used for away the home and need to protect all of the home or office or store etc Stay Partial armed at home in this mode only the outer zones and emergency zones triggered will cause alarm the inner zone triggered will not cause alarm It be used for partial armed e g some people at home and need to monitoring the outer security Disarmed Except the 24 Hours emergency zones triggered will cause alarm all of the other zones triggered will not cause alarm Usually for maintain or other special requirements 3 Alarm Occurrence 1 When alarm occurrence the K2 will send out Alarm SMS Content firstly then automatically dial the authorized ae eee ee CSM SMS Alarm amp Dialer GSM SOS Call System numbers one by one if picked up the call the K2 will stop to sound and enter to listen mode can not speak If nobody picked up or rejected the K2 will dial all of the authorized numbers 3 times in cycle then stop to dial any more
23. the Armed Button and press its SOS button within 2 Seconds the K2 will enter into Armed Mode immediately will not delay 6 12Enable to Alert the first Authorized Number when other number armed or disarmed the K2 Default is Disable If setup successful will return Send Operation Code to 1 Number H is the identification character of this command Tips f enable this function when the Authorized Number that Function 2 Code 1 can dial in to change the status from Stay to Arm call in the K2 will send SMS to the 1st Authorized Number If any other number armed or disarmed the K2 it will send SMS to the 1st Authorized number The SMS content is Armed By Telephone number or Disarmed by Telephone number Disable this function SMS Command is 6 13 Required the K2 callback lf send successful the K2 will call back the user immediately It is special for the Authorized Number that Function 2 Code 1 can dial in to change the status from Stay to Arm to listen on site 6 14 Setup External Power Status Alert Feature Default is 30 minutes If send successful will return SMS M is the identification character of this command Xx 00 99 Default is 30 Unit is minute Xx 00 stands for when external AC Power goes off will send SMS to all authorized numbers or send SMS when AC Power goes on If setup successful will return AC Power Goes off Send SMS Immediately Xx 01 99 stands for when external AC Power goes off more than 01
24. up the Arm Delay Time Table 2 K2 Panel SMS Command List This handbook has been designed as a guide to the installation and operation of K2 GSM Alarm amp Dialer Statements contained in the handbook are general guidelines only and in no way are designed to supersede the instructions contained with other products We recommend that the advice of a registered electrician be sought before any Installation work commences The manufacturer its employees and distributors accept no liability for any loss or damage including consequential damage due to reliance on any material contained in this handbook The manufacturer its employees and distributors accept no liability for GSM Network upgrading or SIMCard upgrading due to the technology specifications contained in this handbook SMS Command List SMS COMMAND Functions amp Actions Very Important AA To arm the K2 in this mode any detector triggered will alarm Please fill the To disarm the K2 in this mode detector triggered will not alarm Installation To switch ON the Siren output Schedule at Page To switch OFF the Siren output 20 before Inquiry the K2 Status and GSM Module IMEI Code programming it The commands should plus Password the format is Password SMS Command i e if the password is 1234 then you can send to arm 1234BB to disarm the AA EE must be Caps Lock CL a CSM SMS Alarm amp Dialer ESM SOS Call System 1 Brief introduction The GSM Alarm a
25. want to know the authorized number list and the password is 1234 then you can send to check it 6 4 Remove the Authorized Number Please overwrite it with another number that you wish to change it or removed it by SMS Command 6 5 Modify the SMS Alarm Content If setup successful will return the SMS Alarm Content B is the identification character of this command Zone Number 00 16 00 stands for the panel SOS button 01 16 stands for the 16 wireless zones SMS Alarm Content When alarm occurrence the K2 will send the SMS Alarm Content to the authorized numbers by SMS Max 40 characters cannot be empty otherwise the K2 will return SMS Alarm Content cannot be set as empty E g if you want to receive SMS Alarm content of the wireless zone 05 is intruder breaking the windows and password is 1234 then you can send SMS 1234B05 intruder breaking the windows 6 6 Inquiry the SMS Alarm Content Setting If setup successful will return the zone number s SMS Alarm Content 6 7 Setup the Zone Attribute If setup successful will return the zone number s Attribute code D is the identification character of this command Zone Number 00 16 00 stands for panel SOS button 01 16 stands for the 16 wireless zones Attribute Code 0 9 stands for how does the K2 will performance when this zone activated 0 stands for entrance when armed the K2 this zone will delay 30 seconds to enter into Armed mode for leaving the home
26. xxxx Stands for the password 4 digits Return SMS Armed When the Password is 1234 8 3 2 Disarm Example 1111BB XxxxBB xxxx Stands for the password digits Return SMS Disarmed When the Password is 1111 8 3 3 Switch On the Siren XXxxCC xxxx Stands for the password 4 digits Return SMS SICONA Example 1111CC When the Password is 1111 8 3 4 Switch OFF the Siren Example 1111DD xxxxDD xxxx Stands for the password 4 digits Return SMS Siren OFF When the Password is 1111 8 4 Inquiry Status and GSM Module IMEI Code XXXXEE xxxx Stands for the password 4 digits Return SMS Armed or Disarmed AC Power ON or AC Power off GSM Value is 17 or other value IMEI Code XXXXXXXXXXXXXXXXXX GSM Alarm System CSM SMS Alarm amp Dialer ESM SOS Call System 8 5 Android Apps Instructions The user can operate the K2 by Android Apps it istree charge For Android Apps please download from our official website The interface of these tools please see below A 7 1 59 PM GSM Alarm Controller Set the phone No first 9 Technical specifications Rated Voltage 12VDC 1A 12V 14VDC standby Consumption 30 35mA Not charging battery Working Consumption 400mA Siren working Working temperature 10 C 60 C Storage temperature 20 C 60 C Relative humidity 10 90 No condensation GSM frequency 850 900 1800 1 900MHz
27. y Mode and not return SMS This is very useful when the user come back home or office to change the K2 to Stay mode with a FREE call from its mobile phone When the user leave the home or store or office dial the K2 again the K2 will be changed to away armed mode and return SMS to ensure the armed operation is successful Tips When any number with this value call in the K2 the K2 will change from Stay to Armed or Armed to Stay if the K2 in Disarmed mode then the first time call in will change theK2 to Stay mode 2 stands for when this number dial to the K2 will be picked up automatically and create 2 way voice communication mode 3 stands for this number cannot access the K2 by dial in will be hang up Nor listen neither change to Stay or Arm Mode Telephone Number authorized number max 18 characters E g if you want to setup 13512345678 as the third authorized number and the password is 1234 country code is 0086 when alarm occurrence this number can receive both SMS and incoming from the K2 when dial to the K2 from this number can change the K2 to Stay or Armed mode Then you can send 12343A1 1 0086135123456 78 to the K2 Will return Ee eee eee GoM SMS Alarm amp Dialer ESM SOS Call System Tell Empty Tel2 Empty Tel3 008613512345678 1 1 Tel4 Empty Tel5 Empty Tel6 Empty 6 3 Inquiry the Authorized number After received this command the K2 will return the SMS as abovementioned E g lf you

Download Pdf Manuals

image

Related Search

Related Contents

MF-7800/UT25 PDFカタログ  HP mp3130 Installation Card  Descarga aquí  HoMedics Therapist Select    Parameter Unit MR-PRU03 INSTRUCTION  

Copyright © All rights reserved.
Failed to retrieve file