SERIAL ATA
Contents
1. G5019750301622 SERIAL ATA HOST CONTROLLER CARD USER MANUAL SATA1620 1622 1623 eSATA1620 1622 1623 WARNING Before installing and activating RAID function please make sure you have a complete backup of your existing data loss due to abuse misuse or neglect Should you have any installation problem please contact us for assistance All other company and product names are trademarks or registered trademarks of their respective owners Installing the Serial ATA host controller card into your computer 1 Turn off your computer and all external devices connect to it Disconnect your computer from the power sources Open the computer case Refer to your manual for more details Find an available PCI slot and remove the slot bracket Save the bracket screw for later use Align the serial ATA host controller card horizontally with respect to the PCI slot and insert it into the slot firmly and evenly Take care not to force it into the slot Once you have properly positioned the Serial ATA host controller card 6 Connect any Serial ATA device to the connector s of the Serial ATA host controller card with the provided Serial ATA cable 7 Connect the HDD led connector CH3 from the computer case to the HDD busy LED connector one Serial ATA host controller card Close the computer case Make sure to reconnect all the external devices to your computer Driver Installation The chapter contains the procedure2. NCQ commands support Memory Interface Support for 256K FLASH and Serial EEPROM Data FIFO 256 Byte data FIFO for each channel On Board PCI Bus Master Engine On board Bus Master Engine relieve the system processor from book keeping and enhance performance Uses Initio s Proprietary Host Adapter Mode of Operation Initio s Proprietary Auto DMA mode IDMA Queued Overlapping ATA Commands support Other Features Disk RAID 0 1 JBOD support SATA hot plug unplug hardware support Implements Power Management Full driver support for all Major Operating Systems Supports Plug and Play allowing users to change configurations without the use of jumpers Integrated Serial ATA Transport link logic and PHY layer Supports 48 bit LBA Logical Block Addressing for hard drives larger than 137GB Supports ATAPI devices LED support for each channel External Flash BIOS Accessories One User Manual One Serial ATA host controller card One Serial ATA cable One Driver CD 4 Click the Next button to confirm the installation 5 Click the Close button it has been successfully installed 6 Restart system During Install the Windows 2000 XP 2003 Operating System to SATA Hard Drive When Windows 2000 XP 2003 Operating System setup program is running 1 Press F6 to install the driver of SATA Host Controller Press F6 if your need to install a third party SCSI or RAID driver 2 Press to Specif
3. s for installing the Windows 98 ME 2000 XP 2003 and Vista Red Hat Linux7 0 8 0 9 0 and Mac OS 8 6x 9 1x 9 2x 10 1x 10 2x 10 3x 10 4 operating systems Macintosh OS 10 2x 10 3x 10 4x support is built into the Macintosh BIOS on the SATA board For Windows 98SE ME 2000 XP Server 2003 Vista Support you will also need this Windows Installer for the RAID drivers and utility in addition to the PC RAID BIOS on the SATA board For adapters based on the INIC 162X SATA host chipset and our SATA E model and SATA I host adaptors use the following Windows drivers INITIO 1620 drivers for the SATA 1620 eSATA 1620 INITIO 1622 drivers for the SATA 1622 eSATA 1622 SATA 1623 eSATA 1623 INITIO 162x_vista Windows 64 bit driver for the SATA 1620 1622 1623 Installing drivers with existing Windows98 ME 2000 XP 2003 and Vista 1 Click the setup exe file to install the application of RAID Manager and driver 2 Click the Next button 3 Click the NEXT button install a different folder by press the Browse button the button of Disk Cost provides the disk space for user to choice Features PCI 32 bit 66MHz interface PCI 2 3 compliant interface Burst transfer rate of 264 Mb s Built in hardware bus master engine Supports both 3 3V and 5V ATA Interface Serial ATA Revision 1 0a Serial ATA II Revision 1 0 Extensions to Serial ATA 1 0a Serial ATA transfer rate of 1 5 GB s Two SATA channels support SATA TCQ and
4. y additional drivers for use with Windows2000 3 Please insert the disk labeled and press ENTER key when ready 4 The content as below is the driver and index file for installation Initio 162x txtsetup oen 5 Select the S ATA Adapter you want from the following list and press Enter key to continue 6 Press the Enter key to continue the Windows setup process Windows 98 ME Driver PnP method for Installation 1 Select the selection of specify the location of the driver and click the NEXT button 2 Choose the specify a location and assign the 162x driver s location 3 Press the NEXT button for installs the driver 4 Press Finish button for finish the installing 5 You can Verify the driver is installed normally or not on Device Manager BIOS Setup If you already have a bootable hard disk connected to the main board s IDE controller but want to use the SATA hard disk connect to the serial ATA host controller card as default bootable driver Driver C you need to set the main board s BIOS to SCSI first Please refer to the main board s user manual for more details
Download Pdf Manuals
Related Search